Dahua VTO1220A User manual

VTO1210C_X User's Manual
V1.0.0

i
Welcome
Thank you for purchasing our product!
This quick start guide is designed to be a reference tool for your system.
Please keep it well for future reference!

ii
Important Safeguards and Warnings
Please read the following safeguards and warnings carefully before using the product in
order to avoid damages and losses.
Note:
Do not expose the device to lampblack, steam or dust. Otherwise it may cause
fire or electric shock.
Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
Do not expose the device to humid environment. Otherwise it may cause fire.
The device must be installed on solid and flat surface in order to guarantee
safety under load and earthquake. Otherwise, it may cause device to fall off or
turnover.
Do not place the device on carpet or quilt.
Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
Do not place any object on the device.
Do not disassemble the device without professional instruction.
Warning:
Please use battery properly to avoid fire, explosion and other dangers.
Please replace used battery with battery of the same type.
Do not use power line other than the one specified. Please use it properly.
Otherwise, it may cause fire or electric shock.
Special Announcement
This manual is for reference only.
All the designs and software here are subject to change without prior written
notice.
owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
t our website for more information.

iii
Table of Contents
1Product Overview............................................................................................... 1
1.1 Product Introduction........................................................................................ 1
1.2 Features.......................................................................................................... 1
2VTO1210C-X Structure ...................................................................................... 2
2.1 Front Panel ..................................................................................................... 2
2.2 Rear Panel (Ports) .......................................................................................... 4
3Typical Networking............................................................................................. 6
4Install VTO ......................................................................................................... 7
4.1 Installation Illustration...................................................................................... 7
4.2 Screw.............................................................................................................. 7
4.3 Installation Steps............................................................................................. 8
4.4 Wiring.............................................................................................................. 8
5Basic Functions.................................................................................................. 9
5.1 Local Config.................................................................................................... 9
5.1.1 IP Setup................................................................................................ 9
5.1.2 Audio Setup .......................................................................................... 9
5.1.3 Issue Card .......................................................................................... 10
5.1.4 Version................................................................................................ 11
5.1.5 Language Selection ............................................................................ 11
5.2 Unlock Function ............................................................................................ 11
5.2.1 Unlock via IC card............................................................................... 11
5.2.2 Unlock via Password........................................................................... 12
5.2.3 VTH Remotely Unlock......................................................................... 12
5.2.4 Login WEB Interface........................................................................... 12
6Web Function................................................................................................... 13
6.1 Login/Logout................................................................................................. 13
6.1.1 System Login...................................................................................... 13
6.1.2 System Logout.................................................................................... 14
6.2 System Config............................................................................................... 14

iv
6.2.1 Local Config........................................................................................ 14
6.2.2 LAN Config ......................................................................................... 19
6.2.3 Indoor Manager................................................................................... 19
6.2.4 Network Config ................................................................................... 21
6.2.5 Video Set............................................................................................ 22
6.2.6 User Manage ...................................................................................... 23
6.2.7 IPC Info............................................................................................... 24
6.2.8 VTO Info ............................................................................................. 25
6.2.9 IP Auto Allocation................................................................................ 26
6.2.10 Publish Information.......................................................................... 26
6.3 Info Search.................................................................................................... 27
6.3.1 Call History ......................................................................................... 28
6.3.2 Alarm Record...................................................................................... 28
6.3.3 Unlock Record .................................................................................... 28
6.4 Status Statistics............................................................................................. 29
Appendix 1 Specifications ....................................................................................... 30

1
1 Product Overview
1.1 Product Introduction
Unit VTO is part of video talk system, and it connects to VTH, providing a bidirectional
video talk between visitor and resident for the purpose of dual identification of image and
audio.
1.2 Features
Video Talk
When VTH, VTO and MGT center (management center) are configured successfully,
it can achieve bidirectional talks among each two parties of VTO, VTH and MGT
center.
Add Multiple VTHs
You can add more than one VTH at once.
IPAuto Allocation
In VTO config interface, after you have set IP segment, you only need to input room
no. when adding VTH, without manual input.
Multiple Methods to Unlock
You can unlock door via password

2
2 VTO1210C-X Structure
2.1 Front Panel
Plug to power, system boots up and wait for 1 minute, screen turns on. System enters
working interface, see Figure 2- 1.
Figure 2- 1
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
Decoration logo.
2
Microphone
Audio input
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Speaker
Output audio
5
Key Panel
1. Button.
a) Backspace function. It is to delete
the previous symbol.
b) Hang up function. It is to hang up
the call.
2. Number button. Input the number 0 to
9.

3
3. button. When you are using the
password to open the door. Press this
button once to begin input. After you
input the password, please press it again
to complete the operation.
4. Call button. After you input the
room number, press it to begin a dial up.
5. Call MGT center button. Press it to
call the center directly.
6. button to page up and down in
contacts. This is a cutomzed button.
6
Card Induction zone
Use the card to open the door.
7
LCD
Here you can view prompt information,
date, time and etc.
Note:
1. “Call: Room No. + ”. Please input
the room number first and then press the
button to dial；
2.”Call MGT Center: Press button”.
Please press the button to call
center.
3.“Password：+ password + ”，If
you want to open the door via the
password, please press the button
and then input the room number and
password. Please press the button
to confirm.
8
Camera
It is to monitor the video of the door.

4
2.2 Rear Panel (Ports)
Figure 2- 2
Please refer to the following sheet for detailed information.
SN
Port Name
Function
1
Vandal Proof Alarm
Button
It can generate an alarm when there is a vandal
operation.
2
Network Port
Connect to the RJ45 port.
3
Access Control Input
Port
Connect to signal from the door sensor, door on/off
signal.
4
Power Port
Connect to 12V DC.
5
Access Control
Output Port
Control NO/NC of door lock.
6
Analog Signal Port
Connect to the analog signal of the distributor.
7
RS422 Port
(Reserved)
Connect to RS422 or RS485 Communication
Device.

5
or

6
3 Typical Networking
Please read the following contents carefully, and install with a rational networking plan.
Network Note:
VTO network port (dual network VTO is in Figure 2- 2 no. network port) connects to switch
IN port.
Select any one network port from switch’s port 1 to 6 to connect to VTH. The switch will
supply power to VTH.

7
4 Install VTO
Unit VTO on-site installation includes: wall embedded installation, door embedded
installation (with box/without box), standalone installation.
This chapter will introduce wall embedded installation of VTO1210C-X series.
4.1 Installation Illustration
Figure 4- 1
4.2 Screw
Component
Illustration
Quantity
M4×40 inner hex flower countersunk flat
head screws-stainless steel
4

8
4.3 Installation Steps
Step 1. Embed plastic housing into wall.
Step 2. Fix device on the bracket with screw.
4.4 Wiring
Please refer to Figure 2- 2.

9
5 Basic Functions
5.1 Local Config
You can configure the device on VTO, including IP setup, audio setup and issue card. You
can view VTO version information as well.
5.1.1 IP Setup
You can set IP address, network gateway, subnet mask and etc. in IP setup interface.
Step 1. In standby interface, press “or ” + “888888” + “ or ” to enter
project setup interface.
Step 2. Select and move by pressing 2 and 8.
Step 3. Press “ or ”. Enter IP setup interface.
Step 4. Select and move by press 2/4/6/8.
Step 5. Press “ or ”. Underline will flash below numbers.
Step 6. Input number via number 0-9, and press “ or ” to confirm.
Step 7. Press “ or ”to exit modificationinterface.
5.1.2 Audio Setup
You can adjust device volume in audio setup interface.
Step 1. In standby interface, press “ or ” + “888888” + “ or ”, to enter
project setup interface.
Step 2. Select and move by pressing 2 and 8.
Step 3. Press “ or ”. Enter audio setup interface.
Step 4. Adjust volume by pressing 4 and 6.
Step 5. Press to save setup.
Step 6. Press “ or ” to exit modification interface.

10
5.1.3 Issue Card
Before issuing card, please ensure the connection between VTH and VTO, and VTH is
added on WEB-end of VTO. The detailed steps to add VTH is in Ch 6.2.3.
Card issuing setup includes password and main card.
You can set right of issuing card in card issuing interface.
5.1.3.1 Issue Card via Password
Step 1. In standby interface, press “ ” + “888888” + ” ”, to enter project setup
interface.
Step 2. Select and move by pressing 2 and 8.
Step 3. Press “ ”.
Enter card issuing setup.
Step 4. Select card issuing via password by press “number key 8”.
Step 5. Input password “002236”. Press “ ” to confirm.
Step 6. Input room no., press “ ” to confirm.
Step 7. Swipe the card you want to authorize.
Step 8. When it prompts you that the process is successful, press “ ” to exit.
You swipe the card at card swiping area, and the system prompts the process is
successful.
5.1.3.2 Issue Card via Main card
Step 1. In standby interface, press “ ” + “888888” + “ ” to enter project setup interface.
Step 2. Select and move by pressing 2 and 8.
Step 3. Press “ ”. Enter card issuing setup.
Step 4. Select card issuing via main card by pressing “number key 8”.
Step 5. Swipe main card. To add main card, please refer to Ch 6.2.3.
Step 6. Input room no., press “ ” to confirm.
Step 7. Swipe the card you want to authorize.
Step 8. When it prompts you that the process is successful, you can continue to

11
authorize more cards, or press “ ” to exit.
You swipe the card at card swiping area, and the system prompts the process is
successful.
5.1.4 Version
You can view version of the device on VTO, including man program version and MCU
version.
Step 1. In standby interface, press “ ” + “888888” +” ” to enter project setup interface.
Step 2. Select and move by pressing 2 and 8.
Step 3. Press “ ”, to enter version interface.
Step 4. By pressing 2 and 8 to move and select main program version or MCU version.
Step 5. Press “ ”, to view corresponding version information.
Step 6. Press “ ” to exit.
5.1.5 Language Selection
You can change language on VTO as you want to.
Step 1. In standby interface, press “ ” + “888888” +” ” to enter project setup
interface.
Step 2. Select and move by pressing 2 and 8.
Step 3. Press “ ” to enter language selection interface.
Step 4. By pressing 2 and 8 to move to and select language.
Step 5. Press “ ” to confirm selection.
5.2 Unlock Function
5.2.1 Unlock via IC card
The door is open after you swipe IC card and the card passed the authentication and
station verification.

12
5.2.2 Unlock via Password
Before you can unlock door via password, you must configure the password on
VTO WEB-end, please refer to Ch 6.2.1.2.
Uniform password: In standby interface, for example your password is “123456”, then
press “+123456+ to unlock. Defualt password can be changed in WEB
interface.
Self password: n standby interface, press “, input 4-digit room no. +
password ” to unlock. For example, to unlock room 101, you shall input:
#0101123456#.
Duress password: In standby interface, for example your password is “654321”, then
input “+ 654321 + ”
5.2.3 VTH Remotely Unlock
Step 1. Under standby interface, input “room no. + ” to call VTH. Or you can press
and select room no. in the contact book, and pressa to call VTH.
Step 2. The VTH accepts call, now you can start a bidirectional talk with the VTH.
Step 3. Resident at the VTH press unlock button to remotely unlock door.
5.2.4 Login WEB Interface
Access VTO via PC, in the browser, input IP address of VTH and enter VTO login page.
Input account and password (admin/admin), click Login to enter. Here you can configure
VTH, please see WEB intro section in this manual.

13
6 Web Function
Warning:
Before you access unit VTO WEB interface via PC, please make sure the PC
and unit VTO are both connected to the Internet and are in the same network
segment. Otherwise, you cannot access.
Before you access unit VTO WEB interface via PC, please make sure you have
set VTO IP address, please refer to Ch 5.1.1.
6.1 Login/Logout
6.1.1 System Login
Step 1. In IE address field, input VTO IP address, and press Enter. See Figure 6- 1.
Figure 6- 1
Step 2. You must input username and password in order to login WEB main interface.
Default username: admin
Default password: admin.
Note:
Once you successfully login in for the first time, please change the login password for
security purpose.
Step 3. Click Login.

14
6.1.2 System Logout
Step 1. Select Logout>Logout to exit system. See Figure 6- 2.
Figure 6- 2
Step 2. Select Logout>Reboot Device to reboot the device. See Figure 6- 3.
Figure 6- 3
6.2 System Config
System Config includes Local Config, LAN Config, Indoor Manager, Network Config,
Video Set, User Manage, IPC Information and others.
6.2.1 Local Config
6.2.1.1 Local Config
Step 1. Select System Config>Local Config.
Step 2. Set parameter. See Figure 6- 4.

15
Figure 6- 4
Parameter
Note
System Type
System type is digital and analog.
Sensor
Set compensation light sensor sensitivity, input number within
0~255. The higher the value, the higher the sensitivity will
be.
Storage Point
Record, snapshot and other info can be stored in FTP server
and SD card. User can login FTP server to view and get
picture or record.
When user select SD card as storage point, please ensure the
SC card is inserted into VTO.
Unit Layer Amount
Set unit layer amount..
Room Amount in
One Layer
Set room amount in one layer.
Create Room
Check to create room no.: according to set room no., system
will add corresponding VTH number in system config>indoor
manager.
Device Type
Display device type.
Reboot Date
In set date, device will reboot.
Version Info
View software version.
Dial Rule
Continuous dial and discontinuous dial.
Language
There are 8 languages for selection.
Step 3. Check room no.
Step 4. Click OK.
According to set room no., system will add corresponding VTH number in system
config>indoor manager. See Figure 6- 5.