Dahua DH-IPC-PSD8802-A180 User manual


Dahua Panoramic + PTZ Network Camera Web3.0
Operation Manual
Version 1.0.1
ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.


Table of Contents
1PRODUCT INTRODUCTION ....................................................................................... 1
1.1 PRODUCT OVERVIEW ............................................................................................... 1
1.2 FUNCTION FEATURES............................................................................................... 2
2INITIAL CONFIG .......................................................................................................... 5
2.1 DEVICE INITIALIZATION ............................................................................................. 5
2.2 RESET PASSWORD .................................................................................................. 7
3BASIC CONFIG.......................................................................................................... 10
3.1 MODIFY IP ADDRESS.............................................................................................. 10
3.1.1 Modify Individually ........................................................................................... 10
3.1.2 Modify in Batches ............................................................................................ 12
3.2 LOG IN WEB INTERFACE ........................................................................................ 13
3.3 MODIFY USER PASSWORD...................................................................................... 15
4GENERAL OPERATION............................................................................................ 18
4.1 LIVE...................................................................................................................... 18
4.1.1 Live Interface Introduction................................................................................ 18
4.1.2 Video Window Function................................................................................... 19
4.1.3 Video Window Adjustment............................................................................... 20
4.2 PLAYBACK............................................................................................................. 24
4.2.1 Video Playback................................................................................................ 25
4.2.2 Picture Playback.............................................................................................. 31
4.3 CONFIGURE ALARM INFO........................................................................................ 33
4.3.1 Understand Alarm Type................................................................................... 33
4.3.2 Subscribe Alarm Information............................................................................ 34
5CONFIG ..................................................................................................................... 36
5.1 CAMERA SETUP..................................................................................................... 36
5.1.1 Set Camera Condition...................................................................................... 36
5.1.2 Set Video Parameter........................................................................................ 49
5.1.3 Configure Audio Parameters............................................................................ 63
5.2 NETWORK SETUP................................................................................................... 65
5.2.1 Set TCP/IP Parameter..................................................................................... 65
5.2.2 Set Connection Parameter............................................................................... 69
5.2.3 Set PPPoE Parameter..................................................................................... 71
5.2.4 Set DDNS Parameter....................................................................................... 72


5.2.5 Set IP Filter...................................................................................................... 74
5.2.6 Set SMTP Parameter....................................................................................... 76
5.2.7 Set UPnP Parameter ....................................................................................... 78
5.2.8 Set SNMP Parameter ...................................................................................... 79
5.2.9 Set Bonjour Parameter .................................................................................... 83
5.2.10 Set Multicast................................................................................................. 84
5.2.11 Set 802.1x Parameter .................................................................................. 86
5.2.12 Set QoS Parameter...................................................................................... 87
5.3 SET PTZ FUNCTION............................................................................................... 88
5.3.1 Set Preset........................................................................................................ 88
5.3.2 Set Tour........................................................................................................... 89
5.3.3 Set Scan.......................................................................................................... 90
5.3.4 Set Pattern....................................................................................................... 91
5.3.5 Enable Pan...................................................................................................... 92
5.3.6 Set PTZ Speed................................................................................................ 93
5.3.7 Set Idle Motion................................................................................................. 94
5.3.8 Set PowerUp.................................................................................................... 95
5.3.9 Set Time Task.................................................................................................. 96
5.3.10 PTZ Restart.................................................................................................. 98
5.3.11 Default.......................................................................................................... 99
5.4 EVENT ................................................................................................................ 100
5.4.1 Set Smart Track............................................................................................. 100
5.4.2 Set Video Detection....................................................................................... 103
5.4.3 Set Audio Detection....................................................................................... 112
5.4.4 Smart Plan..................................................................................................... 114
5.4.5 Set IVS........................................................................................................... 116
5.4.6 Set Face Detection ........................................................................................ 147
5.4.7 Set People Counting...................................................................................... 149
5.4.8 Heat Map....................................................................................................... 154
5.4.9 Set Alarm....................................................................................................... 156
5.4.10 Abnormity................................................................................................... 159
5.5 STORAGE............................................................................................................ 163
5.5.1 Set Schedule ................................................................................................. 163
5.5.2 Destination..................................................................................................... 167
5.5.3 Record Control............................................................................................... 171
5.6 SYSTEM .............................................................................................................. 172
5.6.1 General.......................................................................................................... 172
5.6.2 Account.......................................................................................................... 175
5.6.3 Add Onvif User .............................................................................................. 180


6SYSTEM MAINTENANCE........................................................................................ 183
6.1 MAINTENANCE REQUIREMENTS............................................................................. 183
6.2 AUTO MAINTENANCE............................................................................................ 183
6.2.1 Auto Reboot................................................................................................... 183
6.2.2 Delete Old Files............................................................................................. 184
6.3 BACKUP AND RECOVERY ...................................................................................... 184
6.3.1 Backup Device Config Info............................................................................. 184
6.3.2 Recover Device Config Info........................................................................... 185
6.3.3 Default ........................................................................................................... 186
6.4 UPGRADE............................................................................................................ 186
6.5 VERSION............................................................................................................. 187
6.6 LOG.................................................................................................................... 187
6.7 ONLINE USER...................................................................................................... 189


Important
The following functions are for reference only. Some series products may not support all the functions
listed below.
Cybersecurity Recommendations
1. Change Passwords and Use Strong Passwords
The number one reason systems get “hacked” is due to having weak or default passwords. It is
recommended to change default passwords immediately and choose a strong password whenever
possible. A strong password should be made up of at least 8 characters and a combination of special
characters, numbers, and upper and lower case letters.
2. Update Firmware
As is standard procedure in the tech-industry, we recommend keeping NVR, DVR, and IP camera
firmware up-to-date to ensure the system is current with the latest security patches and fixes.
“Nice to have” recommendations to improve your network security
1. Change Passwords Regularly
Regularly change the credentials to your devices to help ensure that only authorized users are able to
access the system.
2. Change Default HTTP and TCP Ports:
● Change default HTTP and TCP ports for systems. These are the two ports used to communicate and
to view video feeds remotely.
● These ports can be changed to any set of numbers between 1025-65535. Avoiding the default ports
reduces the risk of outsiders being able to guess which ports you are using.
3. Enable HTTPS/SSL:
Set up an SSL Certificate to enable HTTPS. This will encrypt all communication between your devices
and recorder.
4. Enable IP Filter:
Enabling your IP filter will prevent everyone, except those with specified IP addresses, from accessing
the system.
5. Change ONVIF Password:


On older IP Camera firmware, the ONVIF password does not change when you change the system’s
credentials. You will need to either update the camera’s firmware to the latest revision or manually
change the ONVIF password.
6. Forward Only Ports You Need:
● Only forward the HTTP and TCP ports that you need to use. Do not forward a huge range of numbers
to the device. Do not DMZ the device's IP address.
● You do not need to forward any ports for individual cameras if they are all connected to a recorder on
site; just the NVR is needed.
7. Disable Auto-Login on SmartPSS:
Those using SmartPSS to view their system and on a computer that is used by multiple people should
disable auto-login. This adds a layer of security to prevent users without the appropriate credentials
from accessing the system.
8. Use a Different Username and Password for SmartPSS:
In the event that your social media, bank, email, etc. account is compromised, you would not want
someone collecting those passwords and trying them out on your video surveillance system. Using a
different username and password for your security system will make it more difficult for someone to
guess their way into your system.
9. Limit Features of Guest Accounts:
If your system is set up for multiple users, ensure that each user only has rights to features and
functions they need to use to perform their job.
10. UPnP:
● UPnP will automatically try to forward ports in your router or modem. Normally this would be a good
thing. However, if your system automatically forwards the ports and you leave the credentials defaulted,
you may end up with unwanted visitors.
● If you manually forwarded the HTTP and TCP ports in your router/modem, this feature should be
turned off regardless. Disabling UPnP is recommended when the function is not used in real
applications.
11. SNMP:
Disable SNMP if you are not using it. If you are using SNMP, you should do so only temporarily, for
tracing and testing purposes only.


12. Multicast:
Multicast is used to share video streams between two recorders. Currently there are no known issues
involving Multicast, but if you are not using this feature, deactivation can enhance your network security.
13. Check the Log:
If you suspect that someone has gained unauthorized access to your system, you can check the system
log. The system log will show you which IP addresses were used to login to your system and what was
accessed.
14. Physically Lock Down the Device:
Ideally, you want to prevent any unauthorized physical access to your system. The best way to achieve
this is to install the recorder in a lockbox, locking server rack, or in a room that is behind a lock and key.
15. Connect IP Cameras to the PoE Ports on the Back of an NVR:
Cameras connected to the PoE ports on the back of an NVR are isolated from the outside world and
cannot be accessed directly.
16. Isolate NVR and IP Camera Network
The network your NVR and IP camera resides on should not be the same network as your public
computer network. This will prevent any visitors or unwanted guests from getting access to the same
network the security system needs in order to function properly.
Electrical safety
All installation and operation should conform to your local electrical safety codes.
The power source shall conform to the requirement of the Safety Extra Low Voltage (SELV)
standard, and supply power with voltage rated by DC 12 V or AC 24 V according to the Limited
power Source requirement of IEC60950-1. Please note that the power supply requirement is
subject to the device label.
Make sure the power supply is correct before operating the device.
A readily accessible disconnect device shall be incorporated in the building installation wiring
Prevent the power cable from being trampled or pressed, especially the plug, power socket and the
junction extruded from the device.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
Environment


Do not aim the device at strong light to focus, such as lamp light and sun light, otherwise it might
cause over brightness or light marks, which are not the device malfunction, and affect the longevity
of Charge Coupled Device (CCD) or Complementary Metal-Oxide Semiconductor (CMOS).
Do not place the device in a damp or dusty environment, extremely hot or cold temperatures, or the
locations with strong electromagnetic radiation or unstable lighting.
Keep the camera away from water or other liquid to avoid damages to the internal components.
Keep the indoor device away from rain or damp to avoid fire or lightning.
Keep sound ventilation to avoid heat accumulation.
Transport, use and store the device within the range of allowed humidity and temperature.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
Pack the device with standard factory packaging or the equivalent material when transporting the
device.
Privacy Protection Notice
As the device user or data controller, you might collect personal data of others' such as face,
fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be in
compliance with the local privacy protection laws and regulations to protect the legitimate rights and
interests of other people by implementing measures include but not limited to: providing clear and
visible identification to inform data subject the existence of surveillance area and providing related
contact.
About the Manual
The Manual is for reference only. If there is inconsistency between the Manual and the actual product, the
actual product shall govern.
We are not liable for any loss caused by the operations that do not comply with the Manual.
The Manual would be updated according to the latest laws and regulations of related regions. For detailed
information, see the paper User's Manual, CD-ROM, QR code or our official website. If there is
inconsistency between paper User's Manual and the electronic version, the electronic version shall prevail.
All the designs and software are subject to change without prior written notice. The product updates might
cause some differences between the actual product and the Manual. Please contact the customer service for
the latest program and supplementary documentation.
There still might be deviation in technical data, functions and operations description, or errors in print. If
there is any doubt or dispute, please refer to our final explanation.
Upgrade the reader software or try other mainstream reader software if the Guide (in PDF format) cannot be
opened.
All trademarks, registered trademarks and the company names in the Manual are the properties of their


respective owners.
Please visit our website, contact the supplier or customer service if there is any problem occurred when using
the device.
If there is any uncertainty or controversy, please refer to our final explanation


1 Product Introduction
1.1 Product Overview
The product series is able to provide video preview, record, smart track and intelligent behavior
analytics and so on based on the requirements of detail tracking, panoramic monitoring and large scene
monitoring of various industries. The product is widely applied in government enterprise, public facility
management and other industries, besides, it can provide practical serialized solutions separately or
combined with storage device for several application fields such as safe city, industrial park security and
public place safety etc. The product is equipped with following features.
Panoramic coverage and detail tracking
Adopts integrated structure design, it can cover both overall and partial monitoring, the panoramic
camera is able to realize omnibearing coverage for the scene, the speed dome can implement quick
positioning and tracking upon details.
Multi-scenario intelligent application
It can realize intelligent detection, realtime alarm and evidence acquisition for abnormal behaviors via
intrusion and alarm linkage function in several application scenarios.
The main application scenario is shown in Figure 1-1.
Figure 1-1


1.2 Function Features
Realtime Monitoring
Function
Note
Live
Supports preview panoramic camera image and tracking speed dome
image at the same time. It can monitor panorama via panoramic
camera, meanwhile it can check details via manual tracking or
intelligent activated positioning by tracking speed dome.
Supports preview mode switch.
PTZ control
It can operate the tracking speed dome to position and recognize details
via PTZ.
Speed dome PTZ functions include camera rotation, scan, preset, tour,
pattern, pan and position etc.
Talk
It can contact front-end monitoring sites in time and deal with abnormities
quickly after talk is enabled.
Local snapshot
It can monitor the image abnormities via snapshot or triple snapshot during
preview, which is convenient to check and deal with abnormities
subsequently.
Local record
It can record abnormities of monitoring image during preview, which is
convenient to check and deal with abnormities subsequently.
others
Switch video stream or media protocol.
Manually position tracking speed dome to the target location in the
image of panoramic camera.
Zoom in partial area of the tracking speed dome image or roll mouse
to zoom tracking speed dome image.
Check if there is alarm output.
Zoom in partial details of the video image.
Manually track target via tracking speed dome.
It can automatically track target when the target triggers intelligent
rules and generate alarm after setting intelligent rules.
Adjust display effect of the monitoring image.
Enable or disable intelligent rules display.
Supports full screen preview.
Supports to adjust fluency of video image.
Supports to display the video image of panoramic camera and tracking
speed dome according to different layout.
Record
Function
Note
Scheduled
record
The system is able to record automatically according to the schedule which
has been set after scheduled record is set.
Video playback
and download
Playback video files, check valuable video clip. Download valuable video
clip, which can be used as evidence for judgement.
Picture playback
Playback snapshot and check valuable captured pictures.
Alarm linkage
record
It is able to activate corresponding channel to record when alarm happens.
Alarm


Set alarm prompt mode or voice according to alarm type.
Check alarm information.
User Management
Function
Note
User group
management
Support to add, modify and delete new user group.
Support to manage user authority according to user group.
User
Management
Support to add, modify and delete users.
Support to set user authority.
Modify password
Support to modify user password.
Event Management
Function
Note
Smart Track
Support smart track between bullet and speed dome.
Support switch between smart track and tracking speed dome linkage.
Video Detection
Support motion detection, video tamper and scene changing.
When alarm happens, it supports a series of linkage actions, such as
record, relay-out, send email, PTZ and snapshot etc.
Audio Detection
Support input abnormity and intensity change.
When alarm happens, it supports a series of linkage actions, such as
record, relay-out, send email, PTZ and snapshot etc.
IVS
Support general behavior analysis of panoramic camera and tracking
speed dome.
Panoramic camera supports intrusion and tripwire, tracking speed dome
supports cross fence, tripwire, intrusion, object abandoned, fast moving,
parking detection, crowd gathering, object missing and loitering detection.
When alarm happens, it supports a series of linkage actions, such as
linked tracking, linked record, relay-out, send email, PTZ and snapshot etc.
Support to add calibration area, filter disturbance and shadow, valid target
filtration.
Face Detection
Only tracking speed dome supports face detection.
When alarm happens, it supports linked record, relay-out, send email, PTZ
and snapshot etc.
People Counting
Only tracking speed dome supports people counting.
When alarm happens, it supports linked record, relay-out, send email, PTZ
and snapshot etc.
Heat Map
Only tracking speed dome supports heat map.
It supports to check report of heat map.
Alarm Setting
It triggers alarm when external alarm inputs device and generates alarm.
When alarm happens, it supports linked record, relay-out, send email, PTZ
and snapshot etc.


Function
Note
Abnormity
Supports SD card abnormity, network abnormity and illegal access
detection.
It supports linked relay-out and send email when SD card abnormity or
illegal access alarm happens.
It supports linked record and relay-out when network abnormity alarm
happens.


2 Initial Config
In this chapter it is to introduce the device initial config operation, which includes device initialization,
login device, log out WEB interface and password reset.
2.1 Device Initialization
It needs to implement device initialization when you use the device for the first time. Here it is to take
WEB operation as an example to introduce device initialization. You can also initialize device via Quick
Config Tool, NVR and platform etc.
Note
In order to guarantee device safety, please keep admin login password properly after device
initialization, and modify the password regularly.
Step 1
Open IE browser, input camera IP address in the address bar and click Enter.
The system will display the interface of Device Initialization after it is connected successfully, which is
shown in Figure 2-1.
Note
The default IP address is 192.168.1.108.
Figure 2-1
Step 2
It is to set admin login password, please refer to Table 2-1 for more details.


Parameter
Note
User name
The default user name is admin
Password
The password ranges from 8 to 32 digitals. It can contain letters, numbers
and special characters (excluding “'”,“"”,“;”,“:”,“&”) . The password shall
contain at least two categories. Usually we recommend the strong
password.
Confirm
password
Email
Input an email address for reset password purpose. In case you forgot
password in the future, input the security code you got on the assigned
email to reset the password of admin.
Table 2-1
Step 3
Click Save.
The system will display the interface of End-User License Agreement, which is shown in Figure 2-2.
Figure 2-2
Step 4
Select I have read and agree to all terms and click Next.
The system will display the interface of Easy4iP, which is shown in Figure 2-3.


Figure 2-3
Step 5
Click Save and device initialization is completed.
2.2 Reset Password
Users can reset password via reserved email when you forget the password of admin user.
Step 1
Open IE browser, input camera IP address in the address bar and click Enter button.
The system will display the Login interface after it is successfully connected, which is shown in Figure
2-4.


Figure 2-4
Step 2
Click Forgot password?
The system will display the interface of Reset Password, which is shown in Figure 2-5.
Figure 2-5
Step 3
Reset login password.


Scan the QR code according to the interface prompt and acquire security code, then input the security
code which is received via your reserved email.
Caution
Please use the security code to reset the password within 24 hours after you received the security
code via your reserved email. Otherwise the security code will be invalid.
If you fail to use security code for twice continuously, then the system will prompt that it fails to
acquire security code for the third time. It needs hardware to restore device default setting or wait
for 24 hours and acquire it again if it needs to use the device normally.
Step 4
Click next.
The system will display the interface where you can set the new password, which is shown in Figure 2-6.
Figure 2-6
Step 5
Reset Password and Confirm Password.
The password ranges from 8 to 32 digitals. It can contain letters, numbers and special characters
(excluding “'”,“"”,“;”,“:”,“&”) . The password shall contain at least two categories. Usually we recommend
the strong password.
Step 6
Click Save and complete password reset.
The system will display the Login interface.


3 Basic Config
3.1 Modify IP Address
The default IP address of all the devices is 192.168.1.108, please modify device IP address according
to network planning for the first use or during network adjustment.
You can modify device IP address individually or in batch via ConfigTool, you can also log in WEB client
to modify the device IP address.
You can modify device IP address individually when there are less devices or the device login
password is not the same.
You can modify device IP address in batches when there are more devices or the device login
password is the same.
Precondition
ConfigTool installation package has been acquired, please consult technical service if not.
Network intercommunication between PC installed with ConfigTool and device.
3.1.1 Modify Individually
It is going to introduce how to modify device IP address individually via ConfigTool in this chapter.
Note
Please refer to "4.2.1 Set TCP/IP Parameter" for details about modifying IP address via WEB client
login
Step 1
Click and the system displays the interface of Modify IP.
Step 2
Click Search Setting and the system displays the dialog box of Setting, which is shown in Figure 3-1.


Figure 3-1
Step 3
Set the device network segment, login user name and password, and then click OK. The system will
display the searched devices after searching completes.
Note
The default username and password is admin and admin respectively.
Step 4
Click the corresponding of the device whose IP needs to be modified.
The system will pop out a dialog box of Modify IP, which is shown in Figure 3-2.
Figure 3-2