Daikin intelligent Touch Manager User manual

intelligent Touch Manager
Model
DCM601A71
Installation Manual
3P291714-2B

Disclosure
To the User in USA
Part 15 of FCC
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
To the User in CANADA
Canadian ICES-003
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
3English
Safety Considerations
All phases of the eld-installation, including, but not limited to, electrical, piping, safety, etc.
must be in accordance with manufacturer’s instructions and must comply with national,
state, provincial and local codes.
Read these SAFETY CONSIDERATIONS carefully before installing the controller.
After completing the installation, ensure that the controller operates properly during the
startup operation.
Train the customer to operate and maintain the controller. Inform customers that they
should store this Installation Manual with the User’s Manual for future reference.
Always use a licensed installer or contractor to install this product. Improper installation
can result in electrical shock, re, or explosion.
Meanings of WARNING, CAUTION, and NOTE Symbols.
WARNING Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTE Indicates situations that may result in equipment or prop-
erty-damage accidents only.
WARNING
•Only qualied personnel must carry out the installation work.
•Consult your Daikin dealer regarding relocation and reinstallation of the con-
troller.
Improper installation work may result in electric shocks or re.
•Install the controller in accordance with the instructions in the installation man-
ual.
Improper installation may cause electrical shocks or re.
•Use only specied accessories and parts for installation work.
Failure to use specied parts may result in electric shocks, re, or the unit falling.
•Do not disassemble, reconstruct, or repair.
Electric shock or re may occur.
•Make sure that all wiring is secured, that specied wires are used, and that no
external forces act on the terminal connections or wires.
Improper connections or installation may result in re.
•Before touching electrical parts, turn off the unit.

4Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
English
CAUTION
•Keep water out of the controller.
•To avoid electric shock due to entry of water or insects, ll the wiring through-
hole with putty.
•Do not wash the controller with water as it may result in electrical shocks or
re.
•Do not touch the controller buttons with wet ngers.
Touching the buttons with wet ngers can cause an electric shock.
•Do not install the controller in the following locations:
(a) Where a mineral oil mist or oil spray or vapor is produced, for example, in a
kitchen.
Plastic parts may deteriorate and fall off.
(b) Where corrosive gas, such as sulfurous acid gas, is produced.
(c) Near machinery emitting electromagnetic waves.
Electromagnetic waves may disturb the operation of the control system and cause
the unit to malfunction.
(d) Where ammable gas may leak, where there is carbon ber or ignitable dust
suspensions in the air, or where volatile ammables such as thinner or gaso-
line are handled.
Operating the unit in such conditions can cause a re.
(e) High temperature area or directly amed point.
Heating and/or re can occur.
(f) Moist area, where there is exposure to water.
If water enters the inside of the controller, it may cause electric shock and electrical
components may fail.
NOTE
•Install the control wires for the controller at least 3.5 feet (1 meter) away from
televisions or radios to prevent image interference or noise.
Depending on the radio waves, a distance of 3.5 feet (1 meter) may not be sufcient
to eliminate the noise.

Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
5English
Contents
1 Before Installation ................................................................................................... 7
1.1 Checking that all accessories are included ................................................................................ 7
1.2 Understanding external dimensions .......................................................................................... 8
1.3 Understanding where terminals and switches are located ...................................................... 10
1.3.1 Rear face ....................................................................................................................... 10
1.3.2 Front panel .................................................................................................................... 11
1.3.3 Side face ........................................................................................................................ 12
1.3.4 Wiring of cables ............................................................................................................. 12
1.4 Determining installation place .................................................................................................. 13
1.4.1 Installation place and mounting direction ...................................................................... 13
1.4.2 Environmental conditions .............................................................................................. 13
1.4.3 Required space ............................................................................................................. 13
2 Electric Wiring ........................................................................................................ 14
2.1 Removing wiring cover from rear face ..................................................................................... 14
2.2 Connecting DIII-NET-compatible air conditioning equipment................................................... 14
2.2.1 Terminal location and schematic connection diagram ................................................... 15
2.2.2 Wiring specications ...................................................................................................... 16
2.2.3 Precautions for using multiple centralized controllers .................................................... 16
2.3 Connecting a LAN cable .......................................................................................................... 17
2.3.1 Terminal location and schematic connection diagram ................................................... 18
2.3.2 Wiring specications ...................................................................................................... 18
2.4 Connecting I/O module ............................................................................................................ 19
2.4.1 Terminal location and schematic connection diagram ................................................... 19
2.4.2 Wiring specications ...................................................................................................... 19
2.4.3 Address setup................................................................................................................ 20
2.5 Connecting an emergency stop input device or power meter .................................................. 20
2.5.1 Terminal location and schematic connection diagram ................................................... 20
2.5.2 Wiring specications ...................................................................................................... 21
2.6 Connecting iTM plus adaptors ................................................................................................. 21
2.6.1 Terminal location and schematic connection diagram ................................................... 22
2.6.2 Wiring specications ...................................................................................................... 22
2.7 Connecting power supply ........................................................................................................ 23
2.7.1 Terminal location and schematic connection diagram ................................................... 23
2.7.2 Wiring specications ...................................................................................................... 24
3 Secure installation of intelligent Touch Manager ............................................... 25
3.1 Wall mounting .......................................................................................................................... 25
3.1.1 Parts to be used ............................................................................................................ 25
3.1.2 Installation procedure .................................................................................................... 26

6Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
English
3.2 Flush wall mounting ................................................................................................................. 27
3.2.1 Parts to be used ............................................................................................................ 27
3.2.2 Wall opening dimensions ............................................................................................... 27
3.2.3 Installation procedure .................................................................................................... 28
3.3 Mounting to control enclosure.................................................................................................. 30
3.3.1 Parts to be used ............................................................................................................ 30
3.3.2 Wall opening dimensions ............................................................................................... 30
3.3.3 Installation procedure .................................................................................................... 30
4 Basic setup of intelligent Touch Manager ........................................................... 32
4.1 Setting backup battery to ON .................................................................................................. 32
4.2 Turning on power supply for intelligent Touch Manager and air conditioners .......................... 32
4.3 Setting up locale ...................................................................................................................... 33
4.4 Setting time zone ..................................................................................................................... 33
4.5 Setting current time and daylight saving time .......................................................................... 34
4.6 Conrming air conditioner auto registration results ................................................................. 34
4.7 Setting DIII-NET address for each air conditioner ................................................................... 35
4.7.1 Names of buttons and display areas ............................................................................. 35
4.7.2 Setting address with wired remote controller ................................................................. 36
4.7.3 Setting address with navigation remote controller ......................................................... 38
4.7.4
Setting an unique address to each unit (when Power Proportional Distribution (option) is used) ... 39
5 Quick Operation Guide ......................................................................................... 40
5.1 Viewing target area and management point information in list format ..................................... 40
5.2 Displaying areas and management points ............................................................................... 40
5.3 Starting/stopping an area or management point ..................................................................... 41

Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
7English
1 Before Installation
Before you start installing the intelligent Touch Manager, perform the following preparatory
checks.
•Check that the intelligent Touch Manager comes with all accessories.
• Conrm where the terminals and switches of the intelligent Touch Manager are located.
•Check that an appropriate space for installing the intelligent Touch Manager is available.
1.1 Checking that all accessories are included
Based on the following accessory list, check that all accessories for the intelligent Touch
Manager are included. If there is any missing or defective part, contact your DAIKIN dealer
where you purchased the product.
<Accessories included with intelligent Touch Manager>
A B
E
D
F
C
b-1a-1 b-2 b-3
e-2
e-1
d-1 d-2
c-4c-3
f-2
f-1
c-2c-1
A (a-1) intelligent Touch Manager body (1 pc.)
B Wall mounting parts
(b-1) Round-head wood screw (φ4.1×25), 4 pcs. (b-2) P-tight screw (φ3×8), 1 pc.
(b-3) Wall mounting metal plate, 1 pc.
C Flush wall mounting parts
(c-1) Flat-head screw (M4×40), 4 pcs. (c-2) Pan-head screw (M4×14, with spring
washer and plain washer), 4 pcs.
(c-3) Frame bracket, 1 pc. (c-4) Angle bracket, 2 pcs.
D Control enclosure securing parts
(d-1) Pan-head screw (M4×40, with spring washer and plain washer), 4 pcs.
(d-2) Nut (φ4), 4 pcs.
E (e-1) Clamp, 1 pc. (e-2) Push mount tie, 3 pcs.
F (f-1) Installation manual (This manual), 1 pc.
(f-2) Paper template, 2 pcs.

8Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
English
1.2 Understanding external dimensions
•intelligent Touch Manager body
9-9/16
5-31/32
1-5/32
8-5/32
11-13/32
3/16
3/16
3/16
3/16
31/32
31/32
5/165/16 5/165/16
10-3/32
10-23/32
(in.)
•Wall mounting metal plate
7-17/32
9-7/32
2-3/8 1-9/16
Thickness 1/32 (in.)

Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
9English
•Frame bracket
11-3/32
8-3/16
9-7/32
2-7/16
Φ1-17/32
9-1/2
8-27/32
9/32
8-13/16
(in.)Thickness 1/16
•Angle bracket
9-29/32
8-13/16
4-13/32
8-5/16
1-1/8
25/32
1-23/32
15/32
(in.)Thickness 1/16

10 Installation Manual 3P291714-2B
DCM601A71 intelligent Touch Manager
English
1.3 Understanding where terminals and switches are located
Understand the arrangement of terminals and the location of openings on the unit and
plan how to route the cable and in which order to connect its wires to facilitate the instal-
lation procedure. For connection details including the cable type and terminal size, refer to
“2. Electric Wiring”.
1.3.1 Rear face
Most terminals are located on the rear face of the intelligent Touch Manager. However,
they are covered with a terminal cover for safety reasons. Remove 2 screws to detach the
cover, and you can see various types of ports (terminals).
<Rear face of intelligent Touch Manager>
A [POWER] The power line connection terminals. A power supply voltage of 24 VAC (at
60 Hz) is required. Near the terminal block, there is a blue resin cable mount for
securing the power supply cable with the clamp.
B [DIII] The communication line connection terminals for “DIII-NET”, which enables
communications with DAIKIN’s air conditioning equipment.
C [LINE, PHONE] The port used when subscribing to the DAIKIN “Air Conditioning
Network Service System” online monitoring service for air-conditioning systems. To
use the “Air Conditioning Network Service System” service, you need to sign a sepa-
rate maintenance contact.
D [RESERVE] No Use.
E [RS-485] The terminals for connecting serial equipment.
F [plus ADP IF] The terminals for connecting one or more iTM plus adaptors when the
intelligent Touch Manager is used to control more air conditioning devices.
G [Di (1-4), COM] The terminals for stopping air conditioners according to the external
signal in an emergency, for connecting a power meter to calculate the electricity
usage of individual air conditioners, or for other operations.
H [LAN] The port for connecting the intelligent Touch Manager to an Ethernet network.