Daktronics Rc-100 User manual

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

REMOTE CONTROL SYSTEM

RC-100

ALL SPORT OPERATION

MANUAL

P1110

9 February 2018

ED-15133

Rev 11

responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be reproduced or copied

in any form or by any means—graphic, electronic, or mechanical, including photocopying, taping, or information

storage and retrieval systems—without written permission of the publisher.

Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.

– i –

Table of Contents

1 Introduction��1

Important Safeguards ..........................................................................................................................1

Resources ..............................................................................................................................................1

Daktronics Exchange and Repair & Return Programs .....................................................................2

Exchange Program ��2

Repair & Return Program ��3

Daktronics Warranty & Limitation of Liability��3

2 RC-100 System Overview��4

Important Installation Range Considerations��4

3 RC-100 Base Station ��5

Function Setting ....................................................................................................................................5

Selecting Functions ��6

All Sport Scoreboard Controller Function��6

Gen I Operation��6

Channel Setting ....................................................................................................................................7

Synchronizing Multiple Base Stations & Channel Selection .............................................................8

Installations with a Central Base Station ��9

Installations with Base Station Groups ��10

Server/Client Mode Setting ...............................................................................................................11

Wireless Base Station LEDs..................................................................................................................11

LED Error Diagnostics ��12

4 RC-100 Handheld Controller��13

Powering the Controller On & Off ....................................................................................................13

Using the Keypad ��13

Using External Power ��13

Battery Operation...............................................................................................................................13

Idle Time ��13

Battery Recharging ...........................................................................................................................13

Cong Mode.......................................................................................................................................14

Setting Default Radio Channel Number ��14

Setting LCD Contrast��14

Setting Power Save Mode��14

Connect Mode...................................................................................................................................15

Switching to Connect Mode��15

Signal Strength Indicator ��15

Common Keys.....................................................................................................................................16

Alternate Function Keys��17

5 All Sport Applications��18

Selecting All Sport Applications (Code Numbers)..........................................................................18

Keypad Inserts.....................................................................................................................................19

Keypad Insert Operation Concepts ��19

Common All Sport Application Keys ................................................................................................20

– ii –

Table of Contents

New Code (Alternate Function)��20

New Game (Alternate Function) ��20

Start ��21

Stop��21

Set Time ��21

UP/DN (Alternate Function) ��22

Dim (Alternate Function)��22

Manual Horn ��22

Auto Horn ��23

6 Clock/Score Operation ��24

Home/Guest Score +1, -1 ..................................................................................................................24

Period +1..............................................................................................................................................24

Set TOD (Alternate Function) ............................................................................................................24

7 Volleyball Operation��25

Home/Guest Score +1, -1 ..................................................................................................................25

Home/Guest Won +1, -1 ....................................................................................................................25

Reset Game Score .............................................................................................................................25

Game +1, -1 ........................................................................................................................................25

8 Baseball Operation ��26

Home/Guest Score +1, -1 ..................................................................................................................26

Out +1, Inning +1.................................................................................................................................26

Ball, Strike, Clear Ball & Strike.............................................................................................................26

Hit, Error ................................................................................................................................................26

Time, At Bat, H/E (Alternate Function) .............................................................................................27

Time/At Bat..........................................................................................................................................27

9 Play Clock & Pitch Timer Operation��28

Set Reset 1, Set Reset 2 ......................................................................................................................28

Reset 1, Reset 2 ...................................................................................................................................28

10 Segment Timer Operation��29

Segment Timer Information ...............................................................................................................29

First/Last Segment...............................................................................................................................29

Segment Number/Time......................................................................................................................30

Interval Time ........................................................................................................................................30

Copy Range........................................................................................................................................30

Auto Stop.............................................................................................................................................31

Warning Time ......................................................................................................................................31

Current Segment +1 ...........................................................................................................................31

Reset Current Segment......................................................................................................................31

Reset to First Segment ........................................................................................................................31

11 Tennis Operation��32

Court Selection ...................................................................................................................................32

Serve ....................................................................................................................................................32

– iii –

Table of Contents

Game +1 .............................................................................................................................................32

Point .....................................................................................................................................................33

Reset Game ........................................................................................................................................33

Tie Break...............................................................................................................................................33

TOD/Game..........................................................................................................................................33

Set +1 ...................................................................................................................................................33

Matches Won (Alternate Function)..................................................................................................34

Reset Match (Alternate Function) ....................................................................................................34

Next Match (Alternate Function – DakTennis Only) .......................................................................34

Winner (Alternate Function – DakTennis Only)................................................................................34

12 Sand Volleyball Operation ��35

Court Selection ...................................................................................................................................35

Serve ....................................................................................................................................................35

Point .....................................................................................................................................................35

Set +1 ...................................................................................................................................................36

Reset Game/Reset Match.................................................................................................................36

TOD/Game..........................................................................................................................................36

Matches Won (Alternate Function)..................................................................................................36

Game +1, Tie Break, Next Match, Winner........................................................................................36

13 Basketball Operation ��37

Home/Guest Score +1, +2, (+3, -1) ...................................................................................................37

Home/Guest Fouls +1.........................................................................................................................37

Possession ............................................................................................................................................37

Period +1..............................................................................................................................................38

Set TOD (Alternate Function) ............................................................................................................38

1/10 SEC (Alternate Function)...........................................................................................................38

Home/Guest Bonus (Alternate Function) ........................................................................................38

14 Football Operation ��39

Home/Guest Score +1, +6, (+3, -1) ..................................................................................................39

QTR +1..................................................................................................................................................39

Down +1...............................................................................................................................................39

To Go....................................................................................................................................................40

Ball On..................................................................................................................................................40

Home/Guest TOL -1 ............................................................................................................................40

Home/Guest Possession (Alternate Function).................................................................................40

15 Remote Start/Stop Operation ��41

Start .....................................................................................................................................................41

Stop ......................................................................................................................................................41

Manual Horn/Reset ............................................................................................................................41

16 Goal Judge Operation��42

Goal Light On/Off...............................................................................................................................42

17 CAN Handheld Operation ��43

– iv –

Table of Contents

Common CAN Handheld Operation...............................................................................................43

Diving & Synchronized Swimming Operations ................................................................................43

Rodeo Operations..............................................................................................................................43

18 Troubleshooting ��44

Handheld Controller Error Messages................................................................................................44

Base Station Errors...............................................................................................................................45

IN RANGE LED On Start-up ��45

General Base Station Failures��45

Obtaining Base Station Status Information��45

Replacing Handheld Battery ............................................................................................................46

A Reference Drawings ��47

B Sport Inserts ��65

C Daktronics Warranty and Limitation of Liability ��79

Introduction

1

1 Introduction

This manual is designed to explain the operation of the Daktronics RC-100 Remote

Control System for All Sport®applications. For additional information regarding the safety,

installation, operation, or service of this system, refer to the telephone numbers listed in

Daktronics Exchange and Repair & Return Programs (p� 2).

Important Safeguards

• Read and understand all instructions, both general and for specic applications.

• Do not drop the control console or allow it to get wet�

• Do not disassemble control equipment or electronic controls of the display; failure to

follow this safeguard will make the warranty null and void�

• Always turn off and/or unplug the control equipment when it is not in use� Never yank

the power cord to pull the plug from the outlet� Grasp the plug and pull to disconnect�

• Do not let any power cord touch hot surfaces or hang over the edge of a table that

would damage or cut the cord�

• If an extension cord is necessary, a three-pronged, polarized cord should be used�

Arrange the cord with care so that it will not be tripped over or pulled out�

• Inspect console for shipping damage such as rattles and dents, and verify that all

equipment is included as itemized on the packing slip� Immediately report any

problems to Daktronics; save all packing materials if exchange is necessary�

Resources

Figure 1 illustrates a Daktronics drawing label.

This manual refers to drawings by listing the last

set of digits. In the example, the drawing would

be referred to as DWG-1007804. All references to

drawing numbers, appendices, gures, or other

manuals are presented in bold typeface. Any

drawings referenced in a particular section are

listed at the beginning of it as shown below:

Reference Drawing:

System Riser Diagram....................................................................................... DWG-1007804

Daktronics identies manuals by the DD or ED number located on the cover page.

Drawing Number

Figure 1: Drawing Label

Introduction

2

Daktronics Exchange and Repair & Return Programs

Exchange Program

The Daktronics Exchange Program is a service for quickly replacing key components

in need of repair. If a component fails, Daktronics sends a replacement part to the

customer who, in turn, returns the failed component to Daktronics. This decreases

equipment downtime. Customers who follow the program guidelines explained below

will receive this service.

Before contacting Daktronics, identify these important numbers:

Display Serial Number: ________________________________________________________________

Display Model Number: _______________________________________________________________

Job/Contract Number: _______________________________________________________________

Date Manufactured/Installed: _________________________________________________________

Daktronics Customer ID Number: ______________________________________________________

To participate in the Exchange Program, follow these steps:

1� Call Daktronics Customer Service�

Market Description Customer Service Number

Schools (including community/junior colleges), religious

organizations, municipal clubs, and community centers

877-605-1115

Fax: 605-697-4444

Universities and professional sporting events, live events for

auditoriums, and arenas

866-343-6018

Fax: 605-697-4444

2� When the new exchange part is received, mail the old part to Daktronics�

If the replacement part xes the problem, send in the problem part being replaced.

a� Package the old part in the same shipping materials in which the replacement

part arrived.

b� Fill out and attach the enclosed UPS shipping document.

c� Ship the part to Daktronics.

3� The defective or unused parts must be returned to Daktronics within 5 weeks of initial

order shipment�

If any part is not returned within ve (5) weeks, a non-refundable invoice will be

presented to the customer for the costs of replenishing the exchange parts inventory

with a new part. Daktronics reserves the right to refuse parts that have been

damaged due to acts of nature or causes other than normal wear and tear.

Introduction

3

Repair & Return Program

For items not subject to exchange, Daktronics offers a Repair & Return Program. To send

a part for repair, follow these steps:

1� Call or fax Daktronics Customer Service�

Refer to the appropriate number in the chart on the previous page.

2� Receive a case number before shipping�

This expedites repair of the part.

3� Package and pad the item carefully to prevent damage during shipment�

Electronic components, such as printed circuit boards, should be placed in an

antistatic bag before boxing. Daktronics does not recommend using packing

peanuts when shipping.

4� Enclose:

• name

• address

• phone number

• the case number

• a clear description of symptoms

5� Ship to:

Daktronics Customer Service

[Case #]

201 Daktronics Drive, Dock E

Brookings, SD 57006

Daktronics Warranty & Limitation of Liability

The Daktronics Warranty & Limitation of Liability is located in Appendix C. The Warranty is

independent of Extended Service agreements and is the authority in matters of service,

repair, and display operation.

RC-100 System Overview

4

2 RC-100 System Overview

The RC-100 system allows wireless control of multiple

scoring and display applications. This system is made

up of two distinct hardware components: the RC-100

wireless handheld controller, and the RC-100 wireless

Base Station.

The RC-100 wireless handheld controller (Figure 2)

includes a 4x4 keypad and a 97x32 liquid crystal

display (LCD). The RC-100 wireless handheld

controller is used to enter information to be displayed

on a scoreboard or display. The handheld operates

using a 900 MHz radio with internal antenna and

comes with a rechargeable Ni-MH (Nickel Metal

Hydride) 2000 mAh battery which provides 8-10 hours

of operation. A complete RC-100 system may include

multiple RC-100 wireless handheld controllers.

The RC-100 wireless Base Station processes

information received from the wireless handheld

controllers and sends this information to the

scoreboard or another external controller. Based on

the application, an RC-100 wireless receiver may be

mounted inside the display (Figure 3), or placed in an

external tabletop enclosure (Figure 4). An outdoor

enclosure is also available for certain applications.

Important Installation Range Considerations

The wireless Base Station must be located at least 10' (3 m) from the wireless handheld

controller and no more than 500' (152 m) away. If the wireless handheld is used outside

this range, the wireless handheld signal may drop out. Ideally, the handheld controller

should have a clear line-of-sight to the Base Station antenna. Make sure the Base Station

antenna is pointed straight up for best reception (it should look like a capital “L” when

viewed from the side).

Figure 2: RC-100 Handheld Controller

Base Station (Front View) Wireless Receiver (Front View)

Base Station (Rear View)

Figure 3: Internal RC-100 Receiver

Figure 4: External RC-100 Base Station

(Tabletop Enclosure)

RC-100 Base Station

5

3 RC-100 Base Station

The RC-100 wireless Base Station is used to communicate with all RC-100 wireless

handheld controllers on the same channel setting. The RC-100 wireless Base Station also

is used to update connected displays based with information entered on the wireless

handheld controller.

The wireless Base Station includes two switches that must be set to specify the function

number and channel of operation. Refer to Function Setting (p� 5) and Channel

Setting (p� 7), respectively. In addition, the Base Station includes a server/client jumper

that must be set to “Client Mode” in some scenarios that feature multiple displays. Refer

to Server/Client Mode Setting (p� 11) for more information.

Function Setting

The desired RC-100 system function must be congured in the wireless Base Station. A list

of possible functions is shown below, along with the corresponding Function Setting.

Function

Setting

Function

(Base Station Server Mode*)

Function

(Base Station Client Mode*)

0 Default Function (last power up function) All Display Groups

1 CAN Handheld (Judges') Console Display Group 1

2GEN I All Sport Scoreboard Controller Display Group 2

3 DataTime/Data Master Display Control Display Group 3

4 Reserved Display Group 4

5GEN II All Sport Scoreboard Controller Display Group 2

6 Reserved

7 Reserved

8 Reserved

9 Reserved

A Reserved

B Reserved

C Reserved

D Reserved

E Reserved

F Reset Memory/Test** Reset Memory/Test**

* The function of the Base Station depends on whether it is in Server or Client mode. For a

server Base Station, the Function switch sets up the desired application. For a client Base

Station, the Function switch sets up the display group to which this display belongs.

**Function Setting “F” is a special setting which resets all saved memory parameters back

to defaults. This can be used for situations such as when a password needs to be reset. To

use this function, cycle power to the wireless Base Station with the switch in this position

and leave on for 10 seconds. Remove power, change to the desired function and

continue. All saved memory parameters will be set back to default.

RC-100 Base Station

6

Selecting Functions

Refer to Figure 5 for the wireless Base Station circuit board assembly drawing. To access

the circuit board:

• For external Base Station enclosures, remove the two screws securing the top cover,

and lift it off.

• For internal Base Stations, refer to the scoreboard/display manual for component

location and access instructions.

After exposing Base Station circuit board, use a small athead screwdriver to turn the S2

rotary switch labeled FUNCTION to the desired Function Setting.

Base Station (Front View) Wireless Receiver (Front View)

Base Station (Rear View)

Function Select Switch

Figure 5: Function Select Switch (Internal Receiver)

After 5 seconds, the wireless Base Station Server will change its function to match the

new switch setting. (Any connected wireless handheld controllers should change as

well.) When the wireless Base Station Server is turned off and back on, it will always

default to the function set on the switch.

All Sport Scoreboard Controller Function

The All Sport Scoreboard Controller will normally operate with the Function Setting “5”

selected. However, to support legacy products, Gen I mode of operation may be

selected by switching the Function Setting to “2”.

Gen I Operation

Function Setting “2” allows Daktronics Gen I handheld controllers to communicate with

Gen II Base Stations.

Gen II handheld controllers will recognize which generation Base Station they are

communicating with. On rst time power-up, the initialization of the radio will take a little

longer while it attempts to recognize which generation Base Station is present.

After a successful connection, the handheld controller will recognize and connect

immediately with that generation of Base Station.

Keep in mind the following when using the Gen I mode of operation:

• Gen I handheld controllers or Base Stations will not operate in Function “5”.

• All Base Stations operating at the same location must be set to the same Function.

• Gen I handheld controllers display ED14905 Version 1.6 or lower on the LCD at power-

up. Gen I Base Stations are labeled ED14906 Version 2.1 or lower.

• Gen II handheld controllers display ED14905 Version 2.2 or higher on the LCD at

power-up. Gen II Base Stations are labeled ED14906 Version 2.2 or higher.

RC-100 Base Station

7

Channel Setting

The wireless Base Station and wireless handheld device use internal radio modules to

communicate. The radios on both the wireless handheld and wireless Base Station device

can be set to any channel ranging from 1-15. “Channel 1” is the default channel used by

Daktronics for single base-station installations.

Refer to Figure 6 for the wireless Base Station circuit board assembly drawing. To access

the circuit board:

• For external Base Station enclosures, remove the two screws securing the top cover,

and lift it off.

• For internal Base Stations, refer to the scoreboard/display manual for component

location and access instructions.

After exposing Base Station circuit board, use a small athead screwdriver to turn the S1

rotary switch labeled CHANNEL to the desired channel.

Base Station (Front View) Wireless Receiver (Front View)

Base Station (Rear View)

Channel Select Switch

Figure 6: Channel Select Switch (Internal Receiver)

Note: The wireless handheld and Base Station must be set to the same channel to

communicate. To select the channel in the wireless handheld controller, refer to

Cong Mode (p. 14).

Two server Base Stations cannot be powered up in the same area with the same channel

setting, or they will interfere with each other. To avoid this, on power-up the server Base

Station checks to see if there are any other servers located nearby. If another server is

detected, the “IN RANGE” LED (Figure 10) will ash quickly to indicate interference, and

continue to ash until the channel is changed or the conicting Base Station is turned off.

RC-100 Base Station

8

Synchronizing Multiple Base Stations & Channel

Selection

If two or more server Base Stations need to operate at the same time in the same

location, they must each be set to an independent channel and synchronized

accordingly.

The RC-100 wireless system uses frequency-hopping technology to maximize range and

minimize interference from other systems. When multiple server Base Stations are installed

within range of each other (approximately 2000' [610 m]), Base Stations must be able to

synchronize with one another to ensure their hop sequences do not interfere with each

other.

This is accomplished by the use of sync groups. A list of the sync groups and their

corresponding channel numbers and channel groups are shown in the table below.

Sync Group Channel Number Primary Channel Group Extended Channel Group

1 0 All

2 1 2, 3, 4, 5

7, 8, 9, 10, 12(C), 13(D), 14(E), 15(F)

3 6 7, 8, 9, 10 12(C), 13(D), 14(E), 15(F)

4 11(B) 12(C), 13(D), 14(E), 15(F)

The “Channel Number”, “Primary Channel Group”, and “Extended Channel Group”

entries correspond to the settings on the CHANNEL rotary switch (Figure 6) and handheld

settings that pertain to the “Sync Group” shown on the same line. Each “Primary

Channel Group” lists the channels that will attempt to synchronize to this sync channel

as a rst choice. If any Base Stations set to these “Primary Channels” are within range

of a Base Station set to the corresponding sync channel number, the two Base Stations

will sync. The “Extended Channel Group” lists channels that attempt to synchronize to

the corresponding sync channel as a second or third choice. When these channels are

not within range of their primary sync channel, they will attempt to synchronize to the

corresponding sync channel.

When a Base Station is synchronized to a Sync Group, the “IN RANGE” LED (Figure 10)

will ash briey approximately every 5 seconds with the number of times ashed

corresponding to the sync group: 1 = Channel 0, 2 = Channel 1, 3 = Channel 6, 4 =

Channel 11 (B).

Any Base Stations set to channels in the “Channel Groups” section will continuously

scan for sync Base Stations whenever no handheld controllers are connected. This

will allow these boards to be powered up in any sequence and still obtain network

synchronization.

RC-100 Base Station

9

Installations with a Central Base Station

If the installation includes a central Base Station located approximately 3000' (914 m) or

closer to all other Base Stations, a Base Station set on channel 1 may be installed in this

location.

All other Base Stations may be set to values in the primary and extended channel groups

for this channel number to avoid interference within the channels. Figure 7 shows an

example of a baseball facility with 9 diamonds, each having its own server Base Station.

Set to: Channel 2

Syncs to: Channel 1

Set to: Channel 3

Syncs to: Channel 1

Set to: Channel 4

Syncs to: Channel 1

Set to: Channel 5

Syncs to: Channel 1

Set to: Channel 7

Syncs to: Channel 1

Set to: Channel 8

Syncs to: Channel 1

Set to: Channel 9

Syncs to: Channel 1

Set to: Channel 10, 12, 13, 14, or 15

Syncs to: Channel 1

Central Base Station

Set to: Channel 1 (Sync Channel)

Always on & within 3000' (914 m)

of all other Base Stations

Set to: Channel 2

Syncs to: Channel 1

Set to: Channel 3, 4, or 5

Syncs to: Channel 1

Group 1 Central Base Station

Set to: Channel 1 (Sync Channel)

On with Base Stations 2-5

Set to: Channel 7

Syncs to: Channel 6

Set to: Channel 8, 9, or 10

Syncs to: Channel 6

Group 2 Central Base Station

Set to: Channel 6 (Sync Channel)

On with Base Stations 7-10

Set to: Channel 12

Syncs to: Channel 11

Set to: Channel 13, 14, or 15

Syncs to: Channel 11

Group 3 Central Base Station

Set to: Channel 11 (Sync Channel)

On with Base Stations 12-15

Figure 7: Multiple Base Stations w/ Central Location

Note: To remain synchronized with one another, no Base Station in the area may be

set to channel 6 or 11. Also, the central Base Station must remain on at all times

during the operation of any other Base Station.

RC-100 Base Station

10

Installations with Base Station Groups

If the installation does not include a central location as described above, or if groups of

Base Stations will be powered down at times, other groups will need to be active and

using Sync Groups 3 and 4 (channels 6 and 11).

An operator may use Sync Groups 3 and 4 (channels 6 and 11) as synchronizing

channels for two other independent groups of scoreboards that may or may not be in

range of any other groups. Figure 8 shows an example of a baseball facility that also

has 9 diamonds; however, in this setup there is no central location and instead uses 3

independent channel groups.

Set to: Channel 2

Syncs to: Channel 1

Set to: Channel 3

Syncs to: Channel 1

Set to: Channel 4

Syncs to: Channel 1

Set to: Channel 5

Syncs to: Channel 1

Set to: Channel 7

Syncs to: Channel 1

Set to: Channel 8

Syncs to: Channel 1

Set to: Channel 9

Syncs to: Channel 1

Set to: Channel 10, 12, 13, 14, or 15

Syncs to: Channel 1

Central Base Station

Set to: Channel 1 (Sync Channel)

Always on & within 3000' (914 m)

of all other Base Stations

Set to: Channel 2

Syncs to: Channel 1

Set to: Channel 3, 4, or 5

Syncs to: Channel 1

Group 1 Central Base Station

Set to: Channel 1 (Sync Channel)

On with Base Stations 2-5

Set to: Channel 7

Syncs to: Channel 6

Set to: Channel 8, 9, or 10

Syncs to: Channel 6

Group 2 Central Base Station

Set to: Channel 6 (Sync Channel)

On with Base Stations 7-10

Set to: Channel 12

Syncs to: Channel 11

Set to: Channel 13, 14, or 15

Syncs to: Channel 11

Group 3 Central Base Station

Set to: Channel 11 (Sync Channel)

On with Base Stations 12-15

Figure 8: Multiple Base Station Groups

Note: An important limitation exists for channels 1, 6, and 11. Since other channels use

these channels for synchronization purposes, Base Stations on these channels

cannot scan during normal operation, only at power-up. For this reason, these

Base Stations must be powered up in-order (1 rst, then 6, then 11) to maintain

overall network synchronization in the case where it is needed to have Channels

1, 6, and 11 all powered up at the same time.

RC-100 Base Station

11

Server/Client Mode Setting

The RC-100 wireless Base Station can operate in either Server Mode or Client Mode,

depending on application requirements. For most applications, the wireless Base Station

will operate in Server Mode, and no change from the default setting will be necessary.

In Server Mode, the wireless Base Station controls all wireless handheld devices, either

through an onboard program (i.e. All Sport®or DataTime®), or by acting as a router to

pass data back and forth between wireless handheld devices and an external control

system (such as an OmniSport®2000 console). An RC-100 network (on a single channel)

contains one and only one server Base Station device.

In Client Mode, a wireless Base Station relies on another server Base Station to supply

it with data. This client Base Station will typically provide data for a second wireless

scoreboard or display, as needed for All Sport or DataTime functions. Since the Function

Select switch is not needed to select a function when the Base Station is in Client Mode,

the function switch selects the display group instead. For more information, refer to

Function Setting (p� 5).

Refer to Figure 9 for the wireless Base Station circuit board assembly drawing. To access

the circuit board:

• For external Base Station enclosures, remove the two screws securing the top cover,

and lift it off.

• For internal Base Stations, refer to the scoreboard/display manual for component

location and access instructions.

Base Station (Front View) Wireless Receiver (Front View)

Base Station (Rear View)

Server/Client

Select Jumper

Figure 9: Server/Client Select Jumper (Internal Receiver)

Wireless Base Station Server/Client Mode is selected via the X1 SERVER/CLIENT jumper.

Insert the jumper over the top two posts as shown in the CLIENT label on the circuit board

to put the wireless Base Station in Client Mode. For Server Mode, leave the jumper over

the bottom two posts (factory default).

DWG-317837 in Appendix A shows an example of how a server/client system is used to

operate two game timers at opposite ends of a football eld.

Wireless Base Station LEDs

The wireless Base Station circuit board includes several light-emitting diodes (LEDs) for

diagnostic purposes, as shown in Figure 10 and described in the table that follows.

RC-100 Base Station

12

Base Station (Front View) Wireless Receiver (Front View)

Base Station (Rear View)

1

2 3 4 5 6 2 3 4 5 6

1

Figure 10: Wireless Base Station LEDs

# LED Color Function

1POWER Green This LED illuminates when the Base Station or receiver is connected

to a power source.

2CL/RS232 TX Red

This LED ashes when the Base Station transmits Current Loop (CL)

or RS-232 data via wire:

• Current Loop output is used to control scoreboards.

• RS-232 output is used to communicate with external devices,

such as a computer with DakTennis™.

3CL/RS232 RX Green This LED ashes when the Base Station receives Current Loop (CL)

or RS-232 data from another device via wire.

4IN RANGE Amber

On a server Base Station, this LED ashes several times at start-up

to indicate that it is searching for other server Base Stations on

the same channel within range. If one is found, this LED ashes

continuously to indicate that only one server Base Station is

allowed on a given channel. Once in operation mode, this LED

will either be on or off to indicate whether or not one or more

handheld devices are currently connected to the Base Station.

On a client Base Station, this LED is on whenever it is connected to

a server Base Station.

This LED also shows sync status. Refer to Synchronizing Multiple

Base Stations & Channel Selection (p� 8).

5CAN TX Green This LED ashes when Controller Area Network (CAN) data is

transmitted to a connected device, such as the OmniSport 2000.

6CAN RX Red This LED ashes when Controller Area Network (CAN) data is

received from a connected device, such as the OmniSport 2000.

LED Error Diagnostics

The CL/RS232 TX, CL/RS232 RX, IN RANGE, and CAN TX LEDs are also used to display errors

that can occur in wireless Base Station operation. Refer to Section 18: Troubleshooting (p�

44) for more information about these errors.

RC-100 Handheld Controller

13

4 RC-100 Handheld Controller

Powering the Controller On & Off

Using the Keypad

• Press and hold the <ON/OFF> key momentarily to power on the controller. If the LCD

does not display text within a few seconds, the internal battery is most likely dead

and will need to be recharged. Refer to Battery Recharging (p� 13).

• Press and hold the <ON/OFF> key for 5 seconds to power off the controller. The LCD

will display a power down message.

Using External Power

Plugging the wireless handheld controller into an external power

source via the power connector on top of the unit will turn it on

(and charge its internal batteries). The wireless handheld will not

turn off if connected to external power. When connected to

external power, the top line of the LCD will show a power plug

(Figure 11).

When external power is removed and charging is complete, the

wireless handheld will power down after a 5 second prompt to

conserve battery power. Press any key during the prompt after

disconnecting external power to keep the handheld unit powered on.

Battery Operation

When the controller is powered on, an indicator on the top

line of the LCD shows the current battery status (Figure 12). The

three segments within the battery will gradually disappear as

the battery loses its charge.

Idle Time

When using battery power, by default the wireless handheld shuts itself off or “sleeps”

automatically after 45 minutes of inactivity. The idle time setting may be turned off as

described in Cong Mode (p. 14), but to increase battery life, be sure to manually turn

the unit off when it will be inactive for a long period of time.

Battery Recharging

A charger is contained inside the wireless handheld for recharging the batteries.

To recharge the batteries when not in use, simply connect an external power source

to the power connector on top of the unit. A completely discharged battery will

take approximately 1.5 hours of fast charging to recharge. For information on battery

replacement, see Replacing Handheld Battery (p� 46).

A power adapter is included with the wireless handheld controller for recharging

the batteries and providing external power. Daktronics also offers a charging station

capable of recharging up to 6 units at a time. Refer to DWG-231674 in Appendix A for

more information on charging station operation.

Figure 11: External

Power Detect Status

Figure 12: Battery Status

RC-100 Handheld Controller

14

Cong Mode

Cong (“conguration”) mode (Figure 13) is used when

a wireless server Base Station is not controlling a wireless

handheld. Cong mode is used to set up operational

settings in the wireless handheld controller.

If the wireless handheld has not yet been congured

for a specic channel, the Cong mode will start automatically when the device is rst

powered on. If it has been previously congured, the wireless handheld will attempt to

connect at the last connected channel.

• Conguration mode may be entered at any time by pressing and holding the

<CONFIG> key for 5 seconds.

• Use the <↑> and <↓> arrow keys to move through the possible conguration items.

Setting Default Radio Channel Number

Display Action

PRESS ENT TO

SET CHANNEL Press <ENTER> to set the default radio channel number.

RADIO CHANNEL

DEFAULT: NN*

NN = Current Channel #

(Default: 1)

Use the number keys to enter the desired channel number.

Press <ENTER> again to save the setting.

Note: The channel number should match the setting on the

desired wireless Base Station to connect to on power-up.

Refer to Channel Setting (p� 7) for more information on

setting the Base Station channel number.

Setting LCD Contrast

Display Action

PRESS ENT TO

SET CONTRAST

CONTRAST UP - {

CONTRAST DN - }

Press <ENTER> to set the contrast level.

Use the up or down arrow keys on the keypad to set the desired

contrast.

Press <ENTER> again to save the setting.

Setting Power Save Mode

Display Action

PRESS ENT TO

SET PWR ON TIME

POWER SAVE: ON

{ OR } TO SET

Press <ENTER> to set the power off (idle) time. With this setting

enabled, the controller will turn off automatically after 45

minutes of inactivity.

Use the up or down arrow keys on the keypad to turn the power

save mode ON or OFF.

Press <ENTER> again to save the setting.

Figure 13: Cong Mode LCD Icon

Daktronics RC-100 User manual

Popular Control System manuals by other brands