Daktronics RC-100 User manual

Remote Control System
RC-100
DataMaster Operation Manual
ED-15576 Rev 4 –3 May 2016
201 Daktronics Drive PO Box 5128 Brookings, SD 57006-5128
Tel: 1-800-DAKTRONICS (1-800-325-8766) Fax: [phone]
www.daktronics.com/support

ED-15576
Product 1279-99
Rev 4 –3 May 2016
DAKTRONICS, INC.
Copyright 2005-2016
All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher
assumes no responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be
reproduced or copied in any form or by any means –graphic, electronic, or mechanical, including photocopying,
taping, or information storage and retrieval systems –without written permission of the publisher.
All Sport®and DataMaster®are registered trademarks of Daktronics, Inc. All other trademarks used in this manual are the
property of their respective owners.

Table of Contents i
Table of Contents
Section 1: Introduction.................................................................................................................1
1.1 Resources..................................................................................................................................1
1.2 Daktronics Exchange and Repair & Return Programs.......................................................2
Exchange Program ..................................................................................................................2
Before Contacting Daktronics .................................................................................2
Repair & Return Program ......................................................................................................3
Shipping Address .....................................................................................................3
Daktronics Warranty and Limitation of Liability...............................................................3
Section 2: RC-100 System Overview ..........................................................................................5
Section 3: RC-100 Base Station .................................................................................................. 7
3.1 Function Setting ......................................................................................................................7
Selecting Functions .................................................................................................................8
DataTime/DataMaster Display Control Function .............................................................8
3.2 Channel Setting .......................................................................................................................8
3.3 Synchronizing Multiple Base Stations and Channel Selection .........................................9
3.4 Server/Client Mode Setting ................................................................................................10
3.5 Wireless Base Station LEDs .................................................................................................11
LED Error Diagnostics..........................................................................................................12
Section 4: RC-100 Handheld Controller....................................................................................13
4.1 Powering the Controller On and Off..................................................................................13
Using the Keypad..................................................................................................................13
Using External Power...........................................................................................................13
4.2 Battery Operation..................................................................................................................13
Idle Time ................................................................................................................................13
4.3Battery Recharging................................................................................................................13
4.4 Operation Modes ..................................................................................................................14
Config Mode ..........................................................................................................................14
Setting Default Radio Channel Number..............................................................14
Setting LCD Contrast .............................................................................................14
Setting Power Save Mode ......................................................................................15
Connect Mode .......................................................................................................................15
Switching to Connect Mode ..................................................................................15
Signal Strength Indicator .......................................................................................16
4.5 Common Keys .......................................................................................................................16
Alternate Function Keys ......................................................................................................17
Section 5: DataMaster Applications..........................................................................................19
5.1 Selecting DataMaster Applications ....................................................................................19
5.2 DataMaster Application Keys .............................................................................................20
New Code (Alternate Function)..........................................................................................20
Dimming ................................................................................................................................20
Automatic ................................................................................................................21
Manual .....................................................................................................................21
Blank Sign ................................................................................................................21

ii Table of Contents
Display Sequence ..................................................................................................................22
Menu .......................................................................................................................................22
Edit Price Line 1-5 (Gas & Rate Displays Only)..................................................22
Edit Lottery 1-5 (Lottery Displays Only) .............................................................22
LED Test...................................................................................................................23
Display Option (Rate Displays Only) ..................................................................23
Display Option 1-5 (Lottery Displays Only) .......................................................24
Display Status..........................................................................................................24
Display Passcode ....................................................................................................25
Detect Clients...........................................................................................................25
Set Time 12HR.........................................................................................................26
Section 6: Gas Price Operation..................................................................................................27
6.1 Gas Price Controller Operation ...........................................................................................27
6.2 International Gas Price Display Operation........................................................................27
Section 7: Rate Display Operation ............................................................................................29
7.1 Rate Display Controller Operation .....................................................................................29
Section 8: Lottery Display Operation ........................................................................................31
8.1 Lottery Display Controller Operation................................................................................31
Section 9: Troubleshooting........................................................................................................33
9.1 Handheld Controller Error Messages ................................................................................33
9.2 Base Station Errors ................................................................................................................34
IN RANGE LED On Start-up...............................................................................................34
General Base Station Failures ..............................................................................................34
Obtaining Base Station Status Information........................................................................34
9.3 Replacing Handheld Battery ...............................................................................................35
Appendix A: Reference Drawings..................................................................................................37
Appendix B: Daktronics Warranty and Limitation of Liability....................................................39

Introduction 1
Section 1: Introduction
This manual is designed to explain the operation of the Daktronics RC-100 Remote Control System
for DataMaster®applications. For additional information regarding the safety, installation, operation,
or service of this system, refer to the telephone numbers listed in Section 1.2.
Important Safeguards
Read and understand all instructions, both general and for specific applications.
Do not drop the control console or allow it to get wet.
Do not disassemble control equipment or electronic controls of the display;
failure to follow this safeguard will make the warranty null and void.
Always turn off and/or unplug the control equipment when it is not in use.
Never yank the power cord to pull the plug from the outlet. Grasp the plug and
pull to disconnect.
Do not let any power cord touch hot surfaces or hang over the edge of a table that
would damage or cut the cord.
If an extension cord is necessary, a three-pronged, polarized cord should be used.
Arrange the cord with care so that it will not be tripped over or pulled out.
Inspect console for shipping damage such as rattles and dents, and verify that all
equipment is included as itemized on the packing slip. Immediately report any
problems to Daktronics; save all packing materials if exchange is necessary.
1.1 Resources
Figure 1 illustrates a Daktronics
drawing label. The drawing number is
located in the lower-right corner of a
drawing. This manual refers to
drawings by listing the last set of
digits and the letter preceding them.
In the example, the drawing would be
referred to as Drawing C-325405.
Reference Drawing:
System Riser Diagram...........................................................................Drawing C-325405
Daktronics identifies manuals by an ED or DD number located on the cover page of each
manual. For example, this manual would be referred to as ED-15576.
Figure 1: Daktronics Drawing Label

2Introduction
1.2 Daktronics Exchange and Repair & Return Programs
Exchange Program
The Daktronics Exchange Program is a service for quickly replacing key components in need
of repair. If a component fails, Daktronics sends a replacement part to the customer who, in
turn, returns the failed component to Daktronics. This decreases equipment downtime.
Customers who follow the program guidelines explained below will receive this service.
Before Contacting Daktronics
Identify these important numbers:
Assembly Number: ____________________________________________________________
Job/Contract Number: _________________________________________________________
Date Manufactured/Installed: ___________________________________________________
Daktronics Customer ID Number:________________________________________________
To participate in the Exchange Program, follow these steps.
1. Call Daktronics Customer Service:
866-343-3122.
2. When the new exchange part is received, mail the old part to Daktronics.
If the replacement part fixes the problem, send in the problem part being replaced.
a. Package the old part in the same shipping materials in which the replacement
part arrived.
b. Fill out and attach the enclosed UPS shipping document.
c. Ship the part to Daktronics.
3. The defective or unused parts must be returned to Daktronics within 5 weeks of
initial order shipment.
If any part is not returned within five (5) weeks, a non-refundable invoice will be
presented to the customer for the costs of replenishing the exchange parts inventory
with a new part.
Daktronics reserves the right to refuse parts that have been damaged due to acts of
nature or causes other than normal wear and tear.

Introduction 3
Repair & Return Program
For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a
part for repair, follow these steps:
1. Call or fax Daktronics Customer Service:
Phone: [phone] Fax: [phone]
2. Receive a Return Materials Authorization (RMA) number before shipping.
This expedites repair of the part.
3. Package and pad the item carefully to prevent damage during shipment.
Electronic components, such as printed circuit boards, should be placed in an
antistatic bag before boxing.
4. Enclose:
name
address
phone number
the RMA number
a clear description of symptoms
Shipping Address
Daktronics Customer Service
PO Box 5128
201 Daktronics Drive
Brookings, SD 57006
Fax: [phone]
Daktronics Warranty and Limitation of Liability
The Daktronics Warranty and Limitation of Liability is located in Appendix B. The Warranty
is independent of Extended Service agreements and is the authority in matters of service,
repair, and display operation.