DAL ACOUSTICS S10N-TM80 User manual

S10N-TM80 | S10N-TM50
Professional Sound Reinforcement Loudspeaker System
Operation Instructions
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0
A C O U S T I C S

DAL Acoustics loudspeaker systems are designed and manufactured in Germany
by German Audio Engineering GmbH. German Audio Engineering works
exclusively with upstream suppliers who can guarantee consistent and verifiable
quality of their components and parts.
If you have a problem with one of our products, or if you need a spare part, please
contact your local distributor or contact us directly.
Thank you for choosing a DAL Acoustics product.
System Description:
The S10N-TM80 and the S10N-TM50 systems are medium sized 2-way constant
coverage point sources with passive frequency dividing network in a ported
cabinet. The cabinet is made from waterproof glued plywood with textured Poly
Urea coating. The cabinet shape allows the system to be used both as a FOH
system and as a floor monitor. Appropriate control settings of a DAL Control &
Drive System are provided for the different applications. The Variants providing
different horizontal coverage angels of 80°x 50° (h x v S10N-TM80) an 50°x50° (h x
v S10N-TM50). Please note that their horns are not interchangeable due to
different passive frequency dividing networks. The system is protected by a
robust protective grille with inside foam cover . Three integrated handles are
provided for an easier handling. The S10N-TM system is primarily intended for
touring and mobile use. In stand-alone or spaced array operation it can be used
as a main, support or effect speaker. Due to its neutral reproduction
characteristics and the high maximum SPL Level, it is equally suitable for speech
and music transmission. For low end support, the DAL Sub-Low systems, BR115
and BR215 or BR118 and BR218 are suitable.
Featuring an efficient 12"cone driver with 3"voice coil and an N-Dym 1,4" driver
with 3" voice coil on a rotatable horn, the S10N-TM system provides an audio
bandwidth of 60Hz - 20KHz with a Peak power handling of 900W.
The S10N-TM systems can be operated without the DAL Control & Drive Systems.
It has an integrated (RMS) protection limiter for the high frequency driver. When
operated with the DAL Control & Drive System, the system is optimal
parametrized for sonic quality and protected for maximum continuous and peak
sound pressure levels. The DAL Control & Drive Systems provide different settings
for the operation of S10N-TM combinations.
The S10N-TM80 offers a wide horizontal dispersion for stand-alone operation.
The S10N-TM50 is also suitable for tight clustering and arraying with a horizontal
dispersion (h x v 2 x 50° x 50°).
S10N-TM Acessories
U-Mounting Yoke horizontal
U-Mounting Yoke vertical
Truss C-Clamp large
Rigging Splay Cradle 2x50° for 2 of S10N-TM50
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0

Notes On The Operating Instructions:
Observe the explanations and notes in these operating instructions. If you lend or
pass on this product to third parties, please refer to this operating manual, pass
on this operating manual.
This symbol in connection with the signal word "Beware" indicates a possibly
dangerous situation. Failure to observe this safety instruction may result in
serious injury or even death.
This symbol in connection with the signal word "Warning" indicates a possibly
dangerous situation for persons with pacemakers. Non-observance can lead to
serious injuries or even death.
This symbol in connection with the signal word "Caution" indicates a possibly
dangerous situation with a high ambient noise level. It is recommended to wear
hearing protection in case of high noise level.
This symbol in conjunction with the signal word "Caution" indicates a warning of
a magnetic field present in the immediate vicinity of the object.
This symbol in connection with the signal word "Warning" indicates commands
to observe product-relevant operating conditions.
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0

Intended use and application
General information: Operating Instructions DAL S10N-TM.
The information in this operating manual is given to the best of our knowledge
and is valid at the time of printing. We reserve the right to change specifications
of the product at any time. German Audio Engineering does not guarantee the
quality or suitability for use. German Audio Engineering GmbH (for DAL) assumes
no liability for direct or indirect damage or consequential damage resulting from
the use and operation of this product.
German Audio Engineering reserves the right to continuously develop the
product further and to make changes to the product as a result. German Audio
Engineering is always pleased to receive suggestions for improvement and
comments on the product.
Contact: [email protected] * www.GAE.de/DAL
German Audio Engineering GmbH
An der Strusbek 1 * 22926 Ahrensburg, Germany
Phone: [phone]
Safety and operational reliability
Observe the following safety instructions when operating loudspeakers to avoid
risks. The S10N-TM loudspeaker has been designed exclusively for professional
use in sound reinforcement systems. The loudspeaker may only be used by
instructed and qualified personnel. Observe the operating modes described in
these operating instructions. Other applications are not permitted.
The S10N-TM can be operated without the DAL Control & Drive electronics, but
performance data specified by us may differ.
In operation avoid Feedback, distorted signals (clipping), peaks resulting from
plugging or unplugging devices in the signal chain, long term pure sine wave
tones with high power and too weak power amplifiers not specified by their
power ratings. Such signals and devices can cause loudspeaker overload or
damages and are not covered by our warranty
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0

Safety instructions:
Warning
Loudspeakers have a permanent magnetic field. Persons with pacemakers must
not be in the immediate vicinity of loudspeakers, as magnetic fields can lead to
interference with pacemakers. When repairing loudspeakers, it must be ruled out
that the magnetic components come into contact with persons wearing
pacemakers.
Warning
Loudspeakers have a permanent magnetic field. This can interfere with the
operation of other components in the immediate vicinity that are magnetically
sensitive.
Beware
The S10N-TM is suitable for flown operation and offers mounting points for this
purpose. For flown operation, the original Manufacturer hardware must be used
and a proven static of the hanging point is mandatory. When installing and
commissioning in standing or stacked operation, pay careful attention to secure
footing and solid professional mounting. In stacked operation, the loudspeakers
must be secured as a group against slipping or falling over, e. g. with suitable
tension straps on stages. A falling loudspeaker can cause great damage to
property and personal injury. Use only material specified by DAL for the
installation and mounting of DAL loudspeakers. This work must be carried out by
qualified personnel. Observe the applicable safety regulations when doing so.
Caution
Do not stand in the immediate vicinity of loudspeaker systems that are operated
at high sound pressure levels. Wear hearing protection when testing and setting
up speaker systems. These speaker systems - operated at high sound pressure
levels - can endanger health. Even seemingly low sound pressure levels of
90dB/SPL can cause long-term impairment or damage to hearing.
Attention
When setting up, storing and transporting loudspeakers, ensure that excessive
environmental influences such as direct sunlight, moisture, vibrations and dust
have no effect. When operating the loudspeakers, avoid feedback, distorted
signal transmission and playback as well as signal peaks that can be caused by
switching devices in the signal chain on and offor disconnecting them from the
signal chain during operation. Make sure that the loudspeaker is not exposed to
permanent thermal overloads, which may cause fire and result in damage to
property and personal injury. DAL will not be liable for any damage caused in this
way and will not accept any warranty or liability for consequential damage.
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0
Warning
Caution
Beware
Caution

code: 1000408, Type: DAL Adapter plate M10
(8.) Fixing Points M4 (2x3) protective front grill. Protective front grill with foam
backing order code: 1000477 DAL FGS10N
(9.) Rubber Skids on floor monitor bottom
(10.) Lashing Points M8 (2)
(11.) Connector Panel (1+/1-) black, order code: 10000000002 Type DALL ASS-NL-
4-1 white. White, order code:1000000003 Type DALL ASS-NL4-1ws)
(12.) Manufacturer Plate with serial number
Tools required for maintenance: Srewdriver and Bits: TX20, Allan Key 4mm
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0

Purchase Of Spare Parts
Please state the serial number of your product when ordering spare parts.
The serial number identification of your product can be found on the serial
number plate recessed in the rear wall of the loudspeaker system.
The illustration of the serial number plate is shown on the le". The S/N
designation is followed by the serial number of the speaker system.
Technical Specifications
Acoustical Bandwidth (S10N-TM FR-Mode) with DAL DS-4S / DS-4M: 50Hz – 20HHz
Acoustical Bandwidth (S10N-TM Cut-Mode) with DAL DS-4S / DS-4M: 80Hz – 20Hz
Dispersion S10N-TM80 (h x v): typically 80° x 50°, rotatable horn
Dispersion S10N-TM50 (h x v): typically 50° x 50°
Electrical Phase Response: +/- 45°: 150Hz – 20KHz
Nominal Impedance (Re): 8Ohm
System Power: 450W (AES), 900W Peak
Continous SPL: >124dB/1m, Pink Noise Crest Factor 12dB
Peak SPL: > 135dB/1m, Music Signal1
Dimensions (W x H x D mm): 570 x 357 x 330
Net Weight: 20kg
Connectivity: 2 x Speakon™ NL4 1+/1- alternative 2+/2-
Standard Coating: textured black Poly Urea
Recommended Control & Drive System: DAL DS-4S, DAL DS-4M
For operation recall one of the following controller setups for DAL DS-4L DAL DS-
4M or DAL DS-4S:
S10N-TM80FR: Full Range stand - alone operation, spaced arrays
S10N-TM50FR: Full Range stand - alone operation, spaced arrays
S10N-TM2U: Full Range operation in coupled arrays 2 x 50°x50° (h x v)
S10N-TM80Cut: Low Cut operation with sub-/low support
S10N-TMMON
Parallel connection of multiple S10N-TM systems and DAL Control & Drive
Systems:
DS-4L: 3 systems per channel
DS-4M: 2 systems per channel
DS-4S: 2 systems per channel
1 Peak SPL Level with GAE DS-4L
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0
S10N–TM Manufacturer Plate
With Serial Number

Technical Notes
Safety steels may be used only with the M10 threaded inserts. M6 or M8 threaded
inserts in the rear are to be used exclusively with DAL original accessories or are
designed as lashing points. A"er use, make sure that the countersunk screws
belonging to the cabinet are screwed back into the threaded sleeves in order to
maintain an air-tight system.
DAL protective grilles with foam lamination are the mechanical protection
component for the built-in transducers and offer a high acoustic transmission as
well as their affixing minimizes sonic influences of the grilles. The backing or
covering of the grilles with foam serves also as UV-light protection, dust
protection and improves the optical unobtrusive of the systems. Only
undamaged grilles and foams can fulfil these tasks. Replace warped grilles or
worn foams to maintain their function.
By turning the hi-driver/horn unit in the S10N-TM80cabinet, you change the
horizontal and vertical acoustic radiation characteristics of the system. First
remove the protective grille. To do this, remove the M4 TX20 countersunk screws
on top and bottom and clear away the grill. Remove the 4 M4 TX20 screws of the
hi-driver/horn unit. Pull the Hi-Driver/Horn unit a few centimetres out of the
cabinet and turn it by 90°. Refit the Hi-Driver/Horn unit, taking care to ensure an
airtight seal in the groove. Then attach the protective grille back. Mark the
loudspeaker with the changed radiation pattern.
DAL loudspeaker systems with polyurea-coated or painted enclosures are
basically suitable for temporary outdoor operation, even in the rain.
For indefinite operation outdoors as in fixed installations, the loudspeaker
systems must be protected with a hood against direct sunlight and rain. If
necessary, the loudspeaker should be equipped with the optional front grille with
weather protection.
Most DAL loudspeaker systems can be supplied for extra charge from the factory
in a weatherproof (WR) or sea-weatherproof (SWR) variant.
For indefinite operation outdoors in subtropical and tropical areas, the
loudspeaker should be ordered as the WR variant. For indefinite operation at sea
and other areas with a humid and salty atmosphere, the loudspeaker should be
ordered in the SWR equipment variant. Both variants are manufactured at the
factory only.
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0

surface and that the selected load points have a proven load-bearing capacity.
Use approved stands and approved mounting accessories that are designed for
the weight load. Additionally secure the ground stacked or flown speaker system
before commissioning to prevent personal injury and property damage.
Test And Maintenance
The wiring of the loudspeaker components inside the cabinet is according to the
diagram to the le". With an impulse phase checker, which delivers a signal of
non-inverted phase, a signal of positive polarity is obtained directly measured in
front of the cone transducer. If the same test is performed in front of the high
frequency driver/horn, also a signal with positive polarity is obtained.
If the diaphragm of the high-frequency driver is replaced, make sure that the
original spacer ring (if originally fit) made of a thin plastic material remains in the
driver so that the new voice coil is correctly positioned in the magnetic field.
Cone transducer and horn need to fit back airtight in the cabinet a"er service.
It is good practice to check loudspeaker systems frequently in concern of
mechanical integrity and distortion free sound reproduction.
Here is a simple way to quickly check sound reproduction. Use a sine wave
generator with sweep function or a tunable sine wave generator and a power
amplifier. Adjust the test system to deliver an appropriate sound power level and
tune the sine wave generator from low to high frequencies. Listen to the acoustic
output the loudspeaker delivers. The signals should be free of audible
distortions. Mechanical noise from the system or unwanted reproduction of side
tones should be followed up by inspection and search for the root cause.
Fixing and mounting points should be inspected frequently.
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0
S10N-TM - internal wiring schematic

Note on disposal
Observe the applicable national regulations and rules for disposal.
All products manufactured by German Audio Engineering GmbH are B2B
products and are supplied to commercial customers. The adjacent symbol of
the crossed-out trash bin can indicate that this product will be disposed of
exclusively by German Audio Engineering GmbH. For DAL products that do yet
bear this marking, the owner is responsible for proper disposal.
Our registration according to Elektro G is: WEEE-Register-Nr. DE 72073104
Manufacturer's declaration
The declaration applies to: DAL S10N-TM-80 1000524 and S10N-TM-50 1000572
and all model variants that correspond to the factory design and have not been
modified by others.
Applied national standards and technical specifications:
DIN 18800, DIN 1055, DGUV regulation 17, BGI 810-13
Hamburg, 01.06.2018
© German Audio Engineering GmbH*An der Strusbek 1*22926 Ahrensburg – User Manual DAL S10N-TM v1.0