DAN DRYER Bjork 3222 Installation instructions

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 1 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
Björk Baby Changing Station
(with safety strap)
Assembly instructions and user manual
IMPORTANT:
THIS DOCUMENT SHOULD BE
READ THOROUGHLY AND
SAVED FOR FUTURE
REFERENCE
This product is compliant to the Ameri-
can standard ASTM F2285-04, the Euro-
pean EN 12221-, and meets ADA regula-
tions when installed according to ADA
guidelines.

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 2 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
Contents:
Foreword and general information 2
Intended use 2
Manufacturer’s product liability 2
Remarks conc. EN12221 2
Safety and warnings 2
Unpacking and identication of parts 3
Mounting on wall 3
User instructions 6
User instructions (Safety belt) 7
Cleaning instructions 8
Inspection, maintenance and service 8
Fault-nding 8
Spare parts 9
Technical data 10
Declaration of compliance 11
Foreword
Thank you for buying your equipment from
DAN DRYER A/S and congratulations on your
new baby changing table. Install, use and
maintain the unit according to our instructions
for a long and satisfactory service life.
General information
The product can only be installed and used
in accordance with this guide and our safety
instructions. All users of the product must have
read and understood this guide. If you have
any questions concerning the use or mainten-
ance of your changing table, you are welcome
to contact us.
Intended use
The DAN DRYER baby changing station is
designed for use in commercial washrooms.
It should only be used for changing nappies
etc. on small children. Total weight on the table
cannot exceed 80 kg.
Manufacturer’s product liability
DAN DRYER cannot be held liable if the pro-
duct is used or installed in any other manner
than that stated in this guide.
NB:
The product is designed for use indoors in a
dry environment and must NOT be used in
damp or high chlorine environments.
Remarks:
This product if fully compliant with the American
standard ASTM F2285-04 and the European
standard EN 12221-1.
DAN DRYER guarantees this product can
carry a load of 80 kg.
Safety precautions
Prior to use: always check:
• total weight will not exceed 80 kg (evenly
distributed)
• the product is clean.
• the product is not damaged or in any other
way compromised to the extent that using is
hazardous.
WARNING!
Never leave a child unsupervised on the
table!

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 3 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
Unpack the product with care and verify all
parts are present according to the drawings.
Unpacking and identication of parts:
Tools for assembly::
• Torx key T20 (tting the front cover)
• Electric drill
• Spirit level
Packaging
lid
Front cover
Wall module
Packaging for
front cover
Packaging
base
4 x screws for
the front cover
When choosing position, remember to allow for the depth
of the table when lowered, and its height when folded up.
Refer to the dimension diagram at the end of this manual.
When choosing where to place the unit, ensure there are
no entrapment risks when folding it up or down.
Do not install the product near strong heat sources, e.g.
replaces, stoves, etc.
Important:
The table may only be mounted to a wall with proper inte-
rior blocking to bear the weight of the unit (18 kg) and the
maximum load of (80 kg).
Select the correct mounting fasteners for the specic
wall type. Consult an expert (e.g. your local builder’s
merchants) for advice. Screws in the wall bracket are
exposed to a force equivalent to 65 kg of pull each at
maximum load on the table when 4 screws are used in
the upper holes.
We recommend to mount fasteners in all 12 holes to ob-
tain maximum strength and stability.
Mounting on wall:
M4 x 10 mm
Drill template
Recommended mount-
ing height is based on
a working height of
approx. 950 mm.
Tools needed for wall-mounting will
depend on the screws and plugs
used. See the section below. Warning label
98170190
270
350
1744
552
n
7
n
7

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 4 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
Mounting:
1. Holes for mounting the wall bracket should be
marked up and drilled using the drill template
enclosed.
2. Insert wall plugs into the holes.
3. Do not tighten the screws in the four upper plugs
too much. Leave 5 mm space from wall surface.
4. Secure the table on to the wall using the keyholes
(A) at the top of the wall bracket.
Mounting on wall (contd.)
5. Fold the table down carefully, and insert the
remaining screws (B) at the bottom of the
wall bracket.
6. Fasten all screws (A) and (B) tightly to
ensure the wall bracket is securely xed to
the wall.
7. Fit the front cover (D) and fasten it using
the 4 M4 x 10 screws supplied (C)
8. Check the table can fold up and remain in
the upright position.
9. Finish o󰀨 by veryfying the wall bracket is
securely xed to the wall.
(A) (A)
(B) (B) (C)
(C)
(C)
(C)
(D)

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 5 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
Mounting on wall (contd.)
10. Determine the appropriate language version and remove label from the sheet.
11. Warning label is placed as shown.

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 6 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
The table can be folded down to a horizontal position
by carefully pulling the top edge downwards. Make
sure the table is fully extended into its horizontal
position before use.
This table is not intended to be used with a mattress.
Use a paper towel or the like instead.
Always check the table surface is clean and undam-
aged before use.
Do not use if damaged, defective or if not securely
xed to the wall.
Fold the table into its upright position after use by
lifting the front edge of the table and carefully raising
it to vertical.
NOTE
If the table is folded up very aggressively it may
cause damage to the wall.
User instructions
WARNING!
Never leave a child unsupervised
on the table!

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 7 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
For correct use please follow the instructions.
User instructions (Safety belt)
Securing the belt:
Place the child on the table, and con-
nect the two buckle ends.
To indicate the buckle is secured, a
clear click sound is heard.
The belt is now locked and secured.
Releasing the belt:
To release the belt, press the two
safety taps on each side of the buckle.
Separate the two parts.
The belt is now unlocked.
Press
Press
Connect
WARNING!
Never leave a child unsupervised
on the table!

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 8 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
The table can be cleaned using a damp cloth. Use only neutral, liquid cleaning products that do not contain
solvents. Do not hose or high-pressure wash with water or other liquids.
Cleaning instructions
Maintenance and service can only be performed by trained personnel.
We recommend inspecting the table regularly and at least once annually according to the following:
• Check the table is securely xed to the wall, that all moving parts work correctly and are in a safe condi-
tion.
• Check all screwed assemblies are tight.
• Check the table can fold up and remain in the upright position. A force equivalent to approx. 3 kg is nor-
mally required to fold down the table.
• Check the table cannot drop beyond horizontal when folded down. Normally, the table will stay in any
position when released.
• If the table is defective, it must be repaired and restored to usable condition immediately.
Inspection, maintenance and service
Problem: Solution:
The table cannot remain vertical. • The springs are worn and should be replaced immediately. Do not allow
use of the table before it is repaired.
The table drops freely to the horizon-
tal when folded down.
• The springs are worn and should be replaced immediately. Do not allow
use of the table before it is repaired.
The table is not horizontal when
folded down.
• The table is not securely xed to the wall. Check mountings and repair
immediately. Do not allow use of the table before it is repaired.
• More than the maximum permitted weight of 80 kg has been placed on
the table, which has been permanently damaged as a result. Do not
allow use of the table before it is repaired. Contact DAN DRYER or our
dealers.
Fault-nding

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 9 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
Spare parts:
(1) (7)
(2)
(6)
(5)
(4) (3)
Pos. Item number Description
(1) 32002 Wall bracket complete
(2) 32102 Front cover complete (incl. screws)
(3) 32000 Changing surface
(4) 32104 Left cover plate (incl. screws)
(5) 32105 Right cover plate (incl. screws)
(6) 32106 Left rotating arm (complete, incl. all springs, stop, plastic lock and screws)
(7) 32107 Right rotating arm (complete, incl. all springs, stop, plastic lock and screws)
(8) 32058 Safety belt
Use only original accessories and spare parts from DAN DRYER or our dealers.
WARNING!
The table contains sprung elements that can be released under considerable force if
dismantled and can cause injury.
Maintenance and repair that requires dismantling the table can only be performed by
trained personnel to ensure safety.
(8)

Reference Version Document Lang. Page
27-10-2020 Björk Baby Changing Station
User Manual
EN-US 10 of 12
DAN DRYER A/S • Alsikevej 8 • DK-8920 Randers NV • www.dandryer.com • [e-mail]
552
62
100
70
760
710
781
510
305
Force for folding down : ~20 N
Force for folding up : ~20 N
Total net weight : approx. 17 kg.
Max. load at wall : 80 kg. (Evenly distributed across table surface)
Technical data:
Dimensions diagram:
Type plate:
Björk Baby Changing Station. Art no.: 32xx
Serial no.: 3200xxxxxx Prod.: xx-xxxx
DAN DRYER A/S [phone] Dandryer.com
Alsikevej 8, DK-8920 Randers NV