DAN DRYER BIO User manual

ENG Monteringsvejledning, BIO.doc/31.05.2013
IMPORTANT!
This product is covered by the WEEE regulations on the recycling and recovery
of waste electrical and electronic equipment.
This product is not to be treated as household refuse.
This product must be recycled if possible.
Contact local authorities for advice.
The product may also be returned to the manufacturer/distributor free of
charge. The manufacturer/distributor will ensure proper recycling/
disposal.
INSTALLATION
INSTRUCTIONS
DAN DRYER®TYPE BIO
Alsikevej 8 • DK-8920 Randers NV • Tel.: [phone] • Fax: [phone]

ENG Monteringsvejledning, BIO.doc/31.05.2013
INSTALLATION ON CONCRETE, BRICK, PLASTER OR WOODEN WALL:
➊Select a location on an even wall surface
in legal distance from shower or bath tub.
Do not mount in direct sunlight or other
bright source of light, as this may cause
unintended sensor activation of the dryer.
Please note that the recommended
installation height from the floor to the
lower edge of the machine is 350 mm
for adults –and 200 mm for children.
➋Attach the enclosed template onto the wall
using adhesive tape; ensure that the template is level.
Select two screw holes in each of the two mounting brackets and use a
sharp object to mark the centre of these holes on the wall through the
template. For maximum stability, select screw holes as close to bracket
sides as possible.
The distance from the floor to the bottom edge of the upper mounting
bracket (with 6 screw holes) must be 750 mm, and the distance from the
lower edge of the upper mounting bracket to the centre of the upper screw
hole line in the bottom mounting bracket must be 335 mm. Ensure that both
mounting brackets are plumb and level in relation to each other. Drill 4
screw holes, each 30 mm deep.
➌Insert the enclosed plugs into the screw holes and fix mounting brackets to
the wall, using the enclosed screws –or screw for the relevant wall type (cf.
Fig. 1). Apply black spacers between wall and mountings –and washers
between brackets and screw heads.
➍Hang the dryer onto the upper mounting bracket support rests (cf. Fig. 2).
➎Dismount the filter holder at the bottom
of the machine for access to two screw
holes. Apply the two M4 x 16 mm screws
enclosed to fixate the hand dryer onto the
bottom mounting bracket.
➏Open filter holder and insert one of the
two blue filters enclosed. Close and
reinsert filter holder.
➐Connect to standard 230 V wall outlet.
Switch on dryer by pushing the top button behind the cover plate at the top
of the right side of the machine. Test run dryer. To adjust air speed, if
necessary, activate the two bottom buttons in the panel. Push both buttons
at the same time and keep them pushed in for approx. 5 seconds. Air speed
may now be decreased or increased.
DIRECTIONS FOR USE:
➊Subsequent to hand washing, enter hands from the side into the drying
notch and slowly pull back up. Repeat motion, until hands are dry. The
machine will automatically stop when hands are removed –or after a full
20 second cycle.
➋Blue display light indicates that the dryer is connected to power supply.
Orange display light indicates sensor registration.
Green display light indicates hand drying in progress.
Red display light indicates malfunction and need for service.
MAINTENANCE / CLEANING:
➊Switch the machine off in connection with cleaning, emptying of the water
collection tank as well as filter cleaning / replacement.
➋Apply ordinary cleaning agents for surface cleaning with a damp cloth. Avoid
chemicals, wire brushes or other abrasives.
➌Empty water collection tank regularly –and before it is completely full.
➍Pour approx. 2 dl water through the drain once a week and insert and apply
the enclosed drain brush 2-3 times to prevent clogging.
➎Vacuum-clean or rinse the filter holder at the bottom of the machine once a
week. If rinsed, the filter holder must be wiped dry prior to re-insertion.
➏In case of very intensive use, we recommend filter replacement as follows:
- Replace anti-bacterial urethane filter in filter holder approx. once a month.
- Remove filter holder for access to intermediate semi-hepa filter with active
carbon and replace this filter approx. once every 3 months.
- Replace motor filter placed inside fan housing approx. once a year.
Fig. 1
Fig. 3
Fig. 2