Danfoss VLT DriveMotor FCP 106 User manual

1.1.1 Items Supplied
•
Local operating panel (LOP), 175N0128 IP 65, see
Illustration 1.1
•
Fixture for LOP, 175N2717 (included in 175N0128),
see Illustration 1.2
•
LOP cable
Illustration 1.1 Local Operation Panel (LOP) 175N0128 IP 65
Illustration 1.2 Fixture for LOP 175N2717 (included in 175N0128)
1.1.2 Safety Instructions
Refer to VLT
®
DriveMotor FCP 106 and FCM 106 Operating
Instructions for detailed information about safety precautions
for installation.
WARNING
DISCHARGE TIME
The frequency converter contains DC-link capacitors, which
can remain charged even when the frequency converter is
not powered. Failure to wait the specified time after power
has been removed before performing service or repair work,
could result in death or serious injury.
1. Stop motor.
2. Disconnect AC mains, permanent magnet type
motors, and remote DC-link power supplies,
including battery back-ups, UPS, and DC-link
connections to other frequency converters.
3. Wait for the capacitors to discharge fully, before
performing any service or repair work. The duration
of waiting time is specified in Table 1.1.
Voltage
[V]
Power Range
1)
[kW]
Minimum waiting
time
(min)
3x400 0.55–7.5 4
High voltage can be present even when the warning LED indicator
lights are off.
Table 1.1 Discharge Time
1) Power ratings relate to NO, see VLT
®
DriveMotor FCP 106 and FCM 106
Operating Instructions.
Installation Instructions
LOP Connection and Set-up
Danfoss A/S © Rev. 2013-12-02 All rights reserved. MI03L102

1.1.3 Connection to FCP 106 or FCM 106
1. Connect the LOP as shown in Table 1.2 and
Illustration 1.3.
2. After completing connections, cut off or isolate
excess wire.
3. Connect terminal 27 to +24V or set 5-12 Terminal 27
Digital Input to [0] No operation.
Colour of wire Terminal Function
White 53 Reference
Brown 18 Reset
Purple, orange or
grey
19 See Table 1.3, under Key I
Green 27 See Table 1.3, under Key II
Red 12 +24 V
Yellow 50 +10 V
Blue 55 Ground
Table 1.2 Wiring to FCP 106 or FCM 106 Terminals
Illustration 1.3 LOP Connections to FCP 106 or FCM 106
1.1.4 Set-Up
1. Perform set-up according to Table 1.3.
2. Use the [+]/[-] keys to set reference.
3. At power up, the unit is always in stop mode. The set reference is stored during power down. To set up permanent start
mode, connect terminal 12 to terminal 19 and do not connect purple/grey wire to terminal 12. Permanent start mode will
disable the stop function on the LOP.
Function Settings Key I (Start) Key II (Start)
Key (Stop)
Default - Dual speed operation
(connect purple or orange wire)
No changes to factory setting. Run on set
reference (+/-)
Run on 5 Hz
1)
jog speed
Stop (and reset
2)
- if trip)
Function 2 - Dual mode
operation
(connect purple or orange wire)
Select desired modes of operation in Setups 1 and 2
Set 0-10 Active Set-up to [9] Multi Set-up
Set 5-13 Terminal 29 Digital Input to [23] Set-up select bit 0
Run with
Setup 1
Run with
Setup 2
Stop (and reset
2)
- if trip)
Function 3 - Dual direction
operation (connect grey wire)
Set 4-10 Motor Speed Direction to [2] Both directions
Set 5-13 Terminal 29 Digital Input to [11] Start reversing
Run forward Run reverse Stop (and reset
2)
- if trip)
Table 1.3 LOP Operation Mode
1)
Set Jog speed in 3-11 Jog Speed [Hz]
2)
When reset is required, set 5-11 Terminal 19 Digital Input to [1] Reset.
Installation Instructions LOP Connection and Set-up
2 Danfoss A/S © Rev. 2013-12-02 All rights reserved. MI03L102

Installation Instructions LOP Connection and Set-up
MI03L102 Danfoss A/S © Rev. 2013-12-02 All rights reserved. 3

*MI03L102*
MI03L102130R0393 Rev. 2013-12-02