Danfoss VLT HVAC Drive FC 102 User manual

MAKING MODERN LIVING POSSIBLE
Operating Instructions
VLT®HVAC Drive FC 102
110-400 kW
www.danfoss.com/drives

Contents
1 Introduction 4
1.1 Product Overview 4
1.1.1 Interior Views 4
1.1.2 Extended Options Cabinets 5
1.2 Purpose of the Manual 6
1.3 Additional Resources 6
1.4 Product Overview 6
1.5 Internal Controller Functions 7
1.6 Frame Sizes and Power Ratings 7
2 Safety 8
2.1 Safety 8
3 Installation 9
3.1 Planning the Installation Site 9
3.2 Pre-Installation Check List 9
3.3 Mechanical Installation 9
3.3.1 Cooling 9
3.3.2 Lifting 10
3.3.3 Wall Mounting - IP21 (NEMA 1) and IP54 (NEMA 12) Units 10
3.4 Electrical Installation 11
3.4.1 General Requirements 11
3.4.2 Grounding Requirements 14
3.4.2.1 Leakage Current (>3.5 mA) 14
3.4.2.2 Grounding IP20 Enclosures 15
3.4.2.3 Grounding IP21/54 Enclosures 15
3.4.3 Motor Connection 16
3.4.3.1 Terminal Locations: D1h-D4h 16
3.4.3.2 Terminal Locations: D5h-D8h 20
3.4.4 Motor Cable 30
3.4.5 Motor Rotation Check 30
3.4.6 AC Mains Connection 30
3.5 Control Wiring Connection 30
3.5.1 Access 31
3.5.2 Using Screened Control Cables 31
3.5.3 Grounding of Screened Control Cables 31
3.5.4 Control Terminal Types 32
3.5.5 Wiring to Control Terminals 33
3.5.6 Control Terminal Functions 33
3.6 Serial Communication 33
Contents Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 1

3.7 Optional Equipment 34
3.7.1 Load Share Terminals 34
3.7.2 Regeneration Terminals 34
3.7.3 Anti-condensation Heater 34
3.7.4 Brake Chopper 34
3.7.5 Mains Shield 34
3.7.6 Mains Disconnect 34
3.7.7 Contactor 35
3.7.8 Circuit Breaker 35
4 Start Up and Commissioning 36
4.1 Pre-start 36
4.2 Applying Power 37
4.3 Basic Operational Programming 37
4.4 Local-control Test 38
4.5 System Start Up 39
5 User Interface 40
5.1 Local Control Panel 40
5.1.1 LCP Layout 40
5.1.2 Setting LCP Display Values 41
5.1.3 Display Menu Keys 41
5.1.4 Navigation Keys 42
5.1.5 Operation Keys 42
5.2 Back Up and Copying Parameter Settings 42
5.2.1 Uploading Data to the LCP 43
5.2.2 Downloading Data from the LCP 43
5.3 Restoring Default Settings 43
5.3.1 Recommended Initialisation 43
5.3.2 Manual Initialisation 43
6 Programming 44
6.1 Introduction 44
6.2 Programming Example 44
6.3 Control Terminal Programming Examples 46
6.4 International/North American Default Parameter Settings 46
6.5 Parameter Menu Structure 47
6.6 Remote Programming with MCT 10 Set-up Software 52
7 Application Examples 53
7.1 Introduction 53
7.2 Application Examples 53
Contents Operating Instructions
2 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302

7.3 Connection Examples for Control of Motor with External Signal Provider 58
7.3.1 Start/Stop 58
7.3.2 Pulse Start/Stop 58
7.3.3 Speed Up/Down 58
7.3.4 Potentiometer Reference 59
8 Status Messages 60
8.1 Status Display 60
8.2 Status Message Definitions Table 60
9 Warnings and Alarms 63
9.1 System Monitoring 63
9.2 Warning and Alarm Types 63
9.2.1 Warnings 63
9.2.2 Alarm Trip 63
9.2.3 Alarm Trip-lock 63
9.3 Warning and Alarm Displays 63
9.4 Warning and Alarm Definitions 64
9.5 Fault Messages 66
10 Basic Troubleshooting 73
11 Specifications 76
11.1 Power-dependent Specifications 76
11.2 General Technical Data 79
11.3 Fuse Tables 83
11.3.1 Protection 83
11.3.2 Fuse Selection 83
11.3.3 Short Circuit Current Rating (SCCR) 84
11.3.4 Connection Tightening Torques 84
Index 86
Contents Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 3

1 Introduction
1.1 Product Overview
1.1.1 Interior Views
1
15 14
8
9
12
13 (IP 20/Chassis)
13
(IP 21/54
NEMA 1/12)
11
10
16
130BC252.11
Illustration 1.1 D1 Interior Components
130BC301.11
1
2
3
4
5
6
7
8
9
10
11
Illustration 1.2 Close-up View: LCP and Control Functions
1LCP (Local Control Panel) 9 Relay 2 (04, 05, 06)
2 RS-485 serial bus connector 10 Lifting ring
3 Digital I/O and 24 V power supply 11 Mounting slot
4 Analog I/O connector 12 Cable clamp (PE)
5 USB connector 13 Earth (ground)
6 Serial bus terminal switch 14 Motor output terminals 96 (U), 97 (V), 98 (W)
7 Analog switches (A53), (A54) 15 Mains input terminals 91 (L1), 92 (L2), 93 (L3)
8 Relay 1 (01, 02, 03) 16 TB5 (IP21/54 only). Terminal block for anti-condensation heater
Table 1.1 Legend to Illustration 1.1 and Illustration 1.2
NOTICE
For location of TB6 (terminal block for contactor), see chapter 3.4.3.2 Terminal Locations: D5h-D8h.
Introduction Operating Instructions
4 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
1
1

1.1.2 Extended Options Cabinets
If a frequency converter is ordered with one of the
following options, it is supplied with an options cabinet
that makes it taller.
•Brake chopper
•Mains disconnect
•Contactor
•Mains disconnect with contactor
•Circuit breaker
Illustration 1.3 shows an example of a frequency converter
with an options cabinet. Table 1.2 lists the variants for the
frequency converters that include input options.
Options unit
designations
Extension cabinets Possible options
D5h D1h enclosure with
short extension
Brake, Disconnect
D6h D1h enclosure with tall
extension
Contactor, Contactor
with Disconnect,
Circuit Breaker
D7h D2h enclosure with
short extension
Brake, Disconnect
D8h D2h enclosure with tall
extension
Contactor, Contactor
with Disconnect,
Circuit Breaker
Table 1.2 Overview of Extended Options
The D7h and D8h frequency converters (D2h plus options
cabinet), include a 200 mm pedestal for floor mounting.
There is a safety latch on the front cover of the options
cabinet. If the frequency converter is supplied with a mains
disconnect or circuit breaker, the safety latch prevents the
cabinet door from being opened while the frequency
converter is energized. Before opening the door of the
frequency converter, the disconnect or circuit breaker must
be opened (to de-energize the frequency converter) and
the cover of the options cabinet must be removed.
For frequency converters purchased with a disconnect,
contactor or circuit breaker, the name plate label includes
a type code for a replacement that does not include the
option. If there is a problem with the frequency converter,
it is replaced independent of the options.
Refer to chapter 3.7 Optional Equipment for more detailed
descriptions of the input options and other options that
may be added to the frequency converter.
130BC539.10
1754
[69.1]
Illustration 1.3 D7h Enclosure
Introduction Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 5
11

1.2 Purpose of the Manual
This manual provides detailed information for the instal-
lation and start-up of the frequency converter.
Chapter 3 Installation provides requirements for mechanical
and electrical installation, including:
•Input
•Motor
•Control wiring
•Serial communication wiring
•Control terminal functions
Chapter 4 Start Up and Commissioning provides detailed
procedures for:
•Start-up
•Basic operational programming
•Functional testing
The remaining chapters provide supplementary details.
These details include:
•User interface
•Detailed programming
•Application examples
•Start-up
•Troubleshooting
•Specifications
VLT®is a registered trademark.
1.3 Additional Resources
Other resources are available to understand advanced
frequency converter functions and programming.
•The VLT
®
Programming Guide provides greater
detail on working with parameters and many
application examples.
•The VLT
®
Design Guide is intended to provide
detailed capabilities and functionality to design
motor control systems.
•Supplemental publications and manuals are
available from Danfoss.
See www.danfoss.com/BusinessAreas/DrivesSo-
lutions/Documentations/VLT+Technical
+Documentation.htm for listings.
•Optional equipment is available that may change
some of the procedures described. Reference the
instructions supplied with those options for
specific requirements. Contact the local Danfoss
supplier or visit the Danfoss website:
www.danfoss.com/BusinessAreas/DrivesSolutions/
Documentations/VLT+Technical+Documen-
tation.htm, for downloads or additional
information.
1.4 Product Overview
A frequency converter is an electronic motor controller
that converts DC into a variable AC waveform output. The
frequency and voltage of the output are regulated to
control the motor speed or torque. The frequency
converter can vary the speed of the motor in response to
system feedback, such as position sensors on a conveyor
belt. The frequency converter can also regulate the motor
by responding to remote commands from external
controllers.
The frequency converter offers many control, monitoring
and efficiency functions such as:
•Monitoring the system and motor status
•Issuing warnings or alarms for fault conditions
•Starting and stopping the motor
•Optimising energy efficiency
Operation and monitoring functions are available as status
indications to an outside control system or serial communi-
cation network.
Introduction Operating Instructions
6 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
1
1

1.5 Internal Controller Functions
Illustration 1.4 is a block diagram of the frequency
converter's internal components.
Illustration 1.4 Frequency Converter Block Diagram
Area Title Functions
1 Mains input •3-phase AC mains supply to the
frequency converter
2 Rectifier
•The rectifier bridge converts the
AC input to DC current to
supply inverter power.
3 DC-bus •Intermediate DC-bus circuit
handles the DC current.
4 DC reactors
•Filter the intermediate DC circuit
voltage.
•Prove line transient protection.
•Reduce RMS current.
•Raise the power factor reflected
back to the line.
•Reduce harmonics on the AC
input.
Area Title Functions
5 Capacitor bank
•Stores the DC power.
•Provides ride-through protection
for short power losses.
6 Inverter
•Converts the DC into a
controlled PWM AC waveform
for a controlled variable output
to the motor.
7 Output to motor •Regulated 3-phase output
power to the motor
8 Control circuitry
•Input power, internal
processing, output, and motor
current are monitored to
provide efficient operation and
control.
•User interface and external
commands are monitored and
performed.
•Status output and control can
be provided.
Table 1.3 Legend to Illustration 1.4
1.6 Frame Sizes and Power Ratings
kW High Overload 75 90 110 132 160 200 250 315 315
kW Normal Overload 90 110 132 160 200 250 315 355 400
400 V D3h D3h D3h D4h D4h D4h
500 V D3h D3h D3h D4h D4h D4h
525 V D3h D3h D3h D4h D4h D4h D4h
690 V D3h D3h D3h D4h D4h D4h D4h
Table 1.4 kW Rated Frequency Converters
HP High Overload 100 125 150 200 250 300 350 350
HP Normal Overload 125 150 200 250 300 350 400 450
460 V D3h D3h D3h D4h D4h D4h
575 V D3h D3h D3h D4h D4h D4h D4h
Table 1.5 HP Rated Frequency Converters
Introduction Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 7
11

2 Safety
2.1 Safety
WARNING
HIGH VOLTAGE
Frequency converters contain high voltage when
connected to AC mains input power. Qualified personnel
only should perform installation, start up, and
maintenance. Failure to perform installation, start up,
and maintenance by qualified personnel could result in
death or serious injury.
WARNING
UNINTENDED START
When the frequency converter is connected to AC mains,
the motor may start at any time. The frequency
converter, motor, and any driven equipment must be in
operational readiness. Failure to be in operational
readiness when the frequency converter is connected to
AC mains could result in death, serious injury,
equipment, or property damage.
WARNING
DISCHARGE TIME
Frequency converters contain DC-link capacitors that can
remain charged even when the frequency converter is
not powered. To avoid electrical hazards, disconnect AC
mains, any permanent magnet type motors, and any
remote DC-link power supplies, including battery back-
ups, UPS, and DC-link connections to other frequency
converters. Wait for the capacitors to fully discharge
before performing any service or repair work. The
amount of wait time is listed in the Discharge Time table.
Failure to wait the specified time after power has been
removed before doing service or repair could result in
death or serious injury.
Voltage [V] Power range [kW] Minimum waiting time
(minutes)
3x400 90-250 20
3x400 110-315 20
3x500 110-315 20
3x500 132-355 20
3x525 75-250 20
3x525 90-315 20
3x690 90-250 20
3x690 110-315 20
Table 2.1 Discharge Time
Table 2.2 Approvals
The frequency converter complies with UL508C thermal
memory retention requirements. For more information,
refer to the section Motor Thermal Protection in the
product specific design guide.
NOTICE
Imposed limitations on the output frequency
(due to export control regulations):
From software version 6.72 onwards, the output
frequency of the frequency converter is limited to 590
Hz. Software versions 6x.xx also limit the maximum
output frequency to 590 Hz, but these versions cannot
be flashed, that is, neither downgraded nor upgraded.
Safety Operating Instructions
8 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
22

3 Installation
3.1 Planning the Installation Site
NOTICE
Before performing the installation it is important to plan
the installation of the frequency converter. Neglecting
this may result in extra work during and after instal-
lation.
Select the best possible operation site by considering
the following (see details on the following pages and
the respective Design Guides):
•Ambient operating temperature
•Installation method
•How to cool the unit
•Position of the frequency converter
•Cable routing
•Ensure the power source supplies the correct
voltage and necessary current
•Ensure that the motor current rating is within the
maximum current from the frequency converter
•If the frequency converter is without built-in
fuses, ensure that the external fuses are rated
correctly
Voltage [V] Altitude restrictions
380-500 At altitudes above 3,000 m, contact Danfoss
regarding PELV
525-690 At altitudes above 2,000 m, contact Danfoss
regarding PELV
Table 3.1 Installation in High Altitudes
3.2 Pre-Installation Check List
•Before unpacking the frequency converter, ensure
that the packaging is intact. If any damage has
occurred, immediately contact the shipping
company to claim the damage.
•Unpack the frequency converter as close as
possible to the final installation site.
•Ensure the model number number on the
nameplate corresponds to the model number on
the order.
•Ensure that each of the following are rated for
the same voltage:
-Mains (power)
-Frequency converter
-Motor
•Ensure that the frequency converter output
current rating is equal to or greater than the
motor full load current for peak motor
performance.
•Motor size and frequency converter
power must match for proper overload
protection.
•If frequency converter rating is less than
motor, full motor output cannot be
achieved.
3.3 Mechanical Installation
3.3.1 Cooling
•Top and bottom clearance for air cooling must be
provided. Generally, 225 mm (9 in) is required.
•Improper mounting can result in over heating
and reduced performance
•Derating for temperatures starting between 45 °C
(113 °F) and 50 °C (122 °F) and elevation 1,000 m
(3,300 ft) above sea level must be considered. See
VLT
®
HVAC Drive FC 102VLT
®
AQUA Drive FC 202
Design Guide for detailed information.
The high-power frequency converters utilise a back-
channel cooling concept that removes heatsink cooling air,
which carries approximately 90% of the heat out of the
back channel of the frequency converters. The back-
channel air can be redirected from the panel or room
using one of the kits below.
Duct cooling
A back-channel cooling kit is available to direct the heat
sink cooling air out of the panel when an IP20/chassis
frequency converters is installed in a Rittal enclosure. Use
of this kit reduces the heat in the panel and smaller door
fans can be specified on the enclosure.
Cooling out the back (top and bottom covers)
The back-channel cooling air can be ventilated out of the
room so that the heat from the back channel is not
dissipated into the control room.
Installation Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 9
33

NOTICE
A door fan(s) is required on the enclosure to remove the
heat not contained in the backchannel of the frequency
converters and any additional losses generated by other
components inside the enclosure. The total required air
flow must be calculated so that the appropriate fans can
be selected.
Airflow
The necessary airflow over the heat sink must be secured.
The flow rate is shown in Table 3.2.
NOTICE
The fan runs for the following reasons:
•AMA
•DC Hold
•Pre-Mag
•DC Brake
•60% of nominal current is exceeded
•Specific heat sink temperature exceeded (power
size dependent)
•Specific power card ambient temperature
exceeded (power size dependent)
•Specific control card ambient temperature
exceeded
Frame Door fan/top fan Heat sink fan
D1h/D3h 102 m3/hr (60 CFM) 420 m3/hr (250 CFM)
D2h/D4h 204 m3/hr (120 CFM) 840 m3/hr (500 CFM)
Table 3.2 Airflow
3.3.2 Lifting
Always lift the frequency converter using the dedicated
lifting eyes. Use a bar to avoid bending the lifting holes.
176FA245.10
Illustration 3.1 Recommended Lifting Method
WARNING
RISK OF INJURY OR DEATH
The lifting bar must be able to handle the weight of the
frequency converter to ensure that it will not break
during lifting.
•See chapter 11.1 Power-dependent Specifications
for the weight of the different enclosure types.
•Maximum diameter for bar is 2.5 cm (1 inch).
•The angle from the top of the frequency
converter to the lifting cable should be 60°or
greater.
Failure to follow recommendations could result in death
or serious injury.
3.3.3 Wall Mounting - IP21 (NEMA 1) and
IP54 (NEMA 12) Units
Consider the following before selecting the final instal-
lation site:
•Free space for cooling
•Access to open the door
•Cable entry from the bottom
Installation Operating Instructions
10 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
33

3.4 Electrical Installation
3.4.1 General Requirements
This section contains detailed instructions for wiring the
frequency converter. The following tasks are described:
•Wiring the motor to the frequency converter
output terminals
•Wiring the AC mains to the frequency converter
input terminals
•Connecting control and serial communication
wiring
•After power has been applied, checking input
and motor power; programming control terminals
for their intended functions
WARNING
EQUIPMENT HAZARD!
Rotating shafts and electrical equipment can be
hazardous. All electrical work must conform to national
and local electrical codes. It is strongly recommended
that installation, start up, and maintenance be
performed only by trained and qualified personnel.
Failure to follow these guidelines could result in death or
serious injury.
CAUTION
WIRING ISOLATION!
Run input power, motor wiring and control wiring in
three separate metallic conduits or use separated
shielded cable for high frequency noise isolation. Failure
to isolate power, motor and control wiring could result
in less than optimum frequency converter and associated
equipment performance.
Installation Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 11
33

230 VAC
50/60 Hz
230 VAC
50/60 Hz
TB6 Contactor
TB5
R1
1
2
Brake Temp
(NC)
Anti-condensation heater (optional)
(optional)
91 (L1)
92 (L2)
93 (L3)
PE
88 (-)
89 (+)
50 (+10 V OUT)
53 (A IN)
54 (A IN)
55 (COM A IN)
0/4-20 mA
12 (+24 V OUT)
13 (+24 V OUT)
18 (D IN)
20 (COM D IN)
15 mA 200 mA
(U) 96
(V) 97
(W) 98
(PE) 99
(COM A OUT) 39
(A OUT) 42 0/4-20 mA
03
+10 VDC
0 VDC - 10 VDC
0/4-20 mA
24 VDC
02
01
05
04
06 240 VAC, 2A
24 V (NPN)
0 V (PNP)
0 V (PNP)
24 V (NPN)
19 (D IN)
24 V (NPN)
0 V (PNP)
27
24 V
0 V
(D IN/OUT)
0 V (PNP)
24 V (NPN)
(D IN/OUT)
0 V
24 V
29
24 V (NPN)
0 V (PNP)
0 V (PNP)
24 V (NPN)
33 (D IN)
32 (D IN)
1 2
ON
A53 U-I (S201)
ON
21
A54 U-I (S202) ON=0-20 mA
OFF=0-10 V
95
400 VAC, 2A
P 5-00
(R+) 82
(R-) 81
+ - + -
(P RS-485) 68
(N RS-485) 69
(COM RS-485) 61
0 V
5 V
S801
RS-485
RS-485
21
ON
S801/Bus Term.
OFF-ON
3 Phase
power
input
Load Share Switch Mode
Power Supply
Motor
Analog Output
Interface
Relay1
Relay2
ON=Terminated
OFF=Open
Brake
resistor
(NPN) = Sink
(PNP) = Source
= ==
240 VAC, 2A
400 VAC, 2A
0 VDC - 10 VDC
10 VDC
37 (D IN) - option
130BC548.12
Illustration 3.2 Interconnect Diagram
A=Analog, D=Digital
*Terminal 37 (optional) is used for Safe Torque Off. For Safe Torque Off installation instructions, refer to the Safe Torque Off
Operating Instructions for Danfoss VLT
®
Frequency Converters.
**Do not connect cable screen.
Installation Operating Instructions
12 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
33

For safety, comply with the following requirements
•Electronic controls equipment is connected to
hazardous mains voltage. Extreme care should be
taken to protect against electrical hazards when
applying power to the unit.
•Run motor cables from multiple frequency
converters separately. Induced voltage from
output motor cables run together can charge
equipment capacitors even with the equipment
turned off and locked out.
•Field wiring terminals are not intended to receive
a conductor one size larger.
Overload and Equipment Protection
•An electronically activated function within the
frequency converter provides overload protection
for the motor. The overload calculates the level of
increase to activate timing for the trip (controller
output stop) function. The higher the current
draw, the quicker the trip response. The overload
provides Class 20 motor protection. See
chapter 9 Warnings and Alarms for details on the
trip function.
•Because the motor wiring carries high frequency
current, it is important that wiring for mains,
motor power, and control are run separately. Use
metallic conduit or separated shielded wire. See
Illustration 3.3. Failure to isolate power, motor,
and control wiring could result in less than
optimum equipment performance.
•All frequency converters must be provided with
short-circuit and over-current protection. Input
fusing is required to provide this protection, see
Illustration 3.4. If not factory supplied, fuses must
be provided by the installer as part of installation.
See maximum fuse ratings in
chapter 11.3.1 Protection.
Motor
Line Power
Stop
Start
Speed
Control
130BX370.10
Illustration 3.3 Example of Proper Electrical Installation Using
Conduit
Installation Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 13
33

L1
L1
L2
L2
L3
L3
2
91 92 93
1
130BB460.11
Item
#
Description
1 Fuses
2 Ground
Illustration 3.4 Frequency Converter Fuses
Wire Type and Ratings
•All wiring must comply with local and national
regulations regarding cross-section and ambient
temperature requirements.
•Danfoss recommends that all power connections
be made with a minimum 75 °C rated copper
wire.
3.4.2 Grounding Requirements
WARNING
GROUNDING HAZARD!
For operator safety, it is important to ground the
frequency converter properly in accordance with national
and local electrical codes as well as instructions
contained within this document. Do not use conduit
connected to the frequency converter as a replacement
for proper grounding. Ground currents are higher than
3.5 mA. Failure to ground the frequency converter
properly could result in death or serious injury.
NOTICE
It is the responsibility of the user or certified electrical
installer to ensure correct grounding of the equipment in
accordance with national and local electrical codes and
standards.
•Follow all local and national electrical codes to
ground electrical equipment properly
•Proper protective earthing for equipment with
ground currents higher than 3.5 mA must be
established, see chapter 3.4.2.1 Leakage Current
(>3.5 mA)
•A dedicated ground wire is required for input
power, motor power and control wiring
•Use the clamps provided with the equipment for
proper ground connections
•Do not ground one frequency converter to
another in a “daisy chain” fashion
•Keep the ground wire connections as short as
possible
•Using high-strand wire to reduce electrical noise
is recommended
•Follow motor manufacturer wiring requirements
3.4.2.1 Leakage Current (>3.5 mA)
Follow national and local codes regarding protective
earthing of equipment with a leakage current >3.5 mA.
Frequency converter technology implies high frequency
switching at high power. This will generate a leakage
current in the earth connection. A fault current in the
frequency converter at the output power terminals might
contain a DC component, which can charge the filter
capacitors and cause a transient earth current. The earth
leakage current depends on various system configurations
including RFI filtering, screened motor cables, and
frequency converter power.
EN/IEC61800-5-1 (Power Drive System Product Standard)
requires special care if the leakage current exceeds 3.5 mA.
Earthing (grounding) must be reinforced in one of the
following ways:
•Earth (ground) wire of at least 10 mm2
•Two separate earth (ground) wires both
complying with the dimensioning rules
See EN 60364-5-54 § 543.7 for further information.
Installation Operating Instructions
14 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
33

3.4.2.2 Grounding IP20 Enclosures
The frequency converter can be grounded using conduit or
shielded cable. For grounding of the power connections,
use the dedicated grounding points as shown in
Illustration 3.5.
130BC303.10
Illustration 3.5 Grounding Points for IP20 (Chassis) Enclosures
3.4.2.3 Grounding IP21/54 Enclosures
The frequency converter can be grounded using conduit or
shielded cable. For grounding of the power connections,
use the dedicated grounding points as shown in
Illustration 3.6.
130BC304.10
Illustration 3.6 Grounding for IP21/54 Enclosures.
Installation Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 15
33

3.4.3 Motor Connection
WARNING
INDUCED VOLTAGE!
Run output motor cables from multiple frequency
converters separately. Induced voltage from output
motor cables run together can charge equipment
capacitors even with the equipment turned off and
locked out. Failure to run output motor cables separately
could result in death or serious injury.
•For maximum cable sizes, see chapter 11.1 Power-
dependent Specifications
•Comply with local and national electrical codes
for cable sizes
•Gland plates are provided at the base of IP21/54
and higher (NEMA1/12) units
•Do not install power factor correction capacitors
between the frequency converter and the motor
•Do not wire a starting or pole-changing device
between the frequency converter and the motor
•Connect the 3-phase motor wiring to terminals
96 (U), 97 (V), and 98 (W)
•Earth (ground) the cable in accordance with the
instructions provided
•Torque terminals in accordance with the
information provided in chapter 11.3.4 Connection
Tightening Torques
•Follow motor manufacturer wiring requirements
3.4.3.1 Terminal Locations: D1h-D4h
A
A
B
B
33
1.3[ ]
0
0.0[ ]
62
2.4[ ]
101
4.0[ ]
140
5.5[ ] 163
6.4[ ]
185
7.3[ ]
224
8.8[ ]
263
10.4[ ] 293
11.5[ ]
GROUND88
3.5[ ]
0
0.0[ ]
200
7.9[ ]
94
3.7[ ]
244
9.6[ ]
0
0.0[ ]
272
10.7[ ]
0
0.0[ ]
SUW
R T V
3X M8x20 STUD
WITH NUT
SECTION A-A
MAINS TERMINALS
MAINS TERMINAL
SECTION B-B
MOTOR TERMINALS
MOTOR
TERMINAL
130BC305.10
Illustration 3.7 Terminal Locations D1h
Installation Operating Instructions
16 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
33

A
A
B
B
83
3.3[ ]
0
0.0[ ]
188
7.4[ ]
244
9.6[ ]
0
0.0[ ]
290
11.4[ ]
272
10.7[ ]
0
0.0[ ]
22
0.9[ ]
0
0.0[ ]
62
2.4[ ]
101
4.0[ ]
145
5.7[ ]
184
7.2[ ]
223
8.8[ ]
152
6.0[ ]
217
8.5[ ]
292
11.5[ ]
R
S
T
U
V
W
BRAKE
SECTION A-A
MAINS TERMINALS
MAINS
TERMINAL
SECTION B-B
MOTOR TERMINALS AND
BRAKE TERMINALS
MOTOR TERMINAL
BRAKE
TERMINAL
130BC302.10
Illustration 3.8 Terminal Locations D3h
12
130BC533.10
190
[7.5]
75
[3.0]
98
[3.9]
50
[2.0]
1Front view
2 Side view
Illustration 3.9 Loadshare and Regeneration Terminals, D3h
Installation Operating Instructions
MG16D302 Danfoss A/S © Rev. 06/2014 All rights reserved. 17
33

B
B
A
A
254.7
10[ ]
0.0
0[ ]
GROUND143.4
6[ ]
0.0
0[ ]
GROUND168.4
7[ ]
331.2
13[ ]
211.1
8[ ]
GROUND168.4
7[ ]
GROUND143.4
6[ ]
42.4
2[ ]
0.0
0[ ]
68.1
3[ ]
125.8
5[ ]
183.5
7[ ]
245.8
10[ ]
299.8
12[ ]
353.8
14[ ] 377.6
15[ ]
284.2
11[ ]
0.0
0[ ]
R
S
T
U
V
W
4X M10x20 STUD
WITH NUT
SECTION B-B
MOTOR TERMINALS AND
BRAKE TERMINALS
MOTOR TERMINAL
SECTION A-A
MAINS TERMINALS
MAINS TERMINAL
130BC332.10
Illustration 3.10 Terminal Locations D2h
A
A
B
B
33
1.3[ ]
0
0.0[ ]
91
3.6[ ]
149
5.8[ ]
211
8.3[ ]
265
10.4[ ]
319
12.6[ ]
200
7.9[ ]
0
0.0[ ]
319
12.6[ ]
376
14.8[ ]
293
11.5[ ]
255
10.0[ ]
0
0.0[ ]
306
12.1[ ]
284
11.2[ ]
0
0.0[ ]
236.8
9[ ]
R
S
T
U
V
W
BRAKE
TERMINALS
SECTION A-A
MAINS TERMINALS
MAINS TERMINAL
SECTION B-B
MOTOR TERMINALS AND
BRAKE TERMINALS
TERMINAL
BRAKE / REGEN
MOTOR TERMINAL
130BC333.10
Illustration 3.11 Terminal Locations D4h
Installation Operating Instructions
18 Danfoss A/S © Rev. 06/2014 All rights reserved. MG16D302
33