Danfoss iC7 Series User manual

1 Overview
1.1 Description
The in-back/out-back cooling kit fits FA09 and FA10 frequency converters mounted in Rittal TS8 cabinets. When the kit is installed,
air flows into the lower back duct and out through the upper back duct of the frequency converter. See Illustration 1.
e30bx518.10
3
4
2
1
Illustration 1: Direction of Airflow with the Kit Installed
1
Top cover
2
Cooling back channel
3
Airflow direction
4
Lower duct (intake)
1.2 Kit Numbers
Use these instructions with the following kits.
Table 1: In-back/Out-back Cooling Kits
Number
Kit description
176F4045
In-back/out-back cooling kit for FA09 frequency converter
176F4046
In-back/out-back cooling kit for FA10 frequency converter
AN371942471353en-000101 / 136R0248 | 1Danfoss A/S © 2022.03
Installation Guide
In-back/Out-back Cooling Kit for FA09-FA10
iC7 Series Frequency Converters

1.3 Items Supplied
The kit contains the following parts:
Table 2: Contents of In-back/Out-back Cooling Kit
Item
Quantity
Top cover
1
Top cover gasket
1
Strip gasket
1
Upper back vent
1
Upper vent gasket
2
Lower back vent
1
Lower vent gasket
2
Clip-on nut
12
M5x18 screw
12–16
M6x12 screw
10–12
Mounting plate gasket (upper)
2
Mounting plate gasket (lower)
2
Seal plate gasket
2
Seal plate
2
Lower duct frame
1
Front cover, lower duct
1
Front gasket, lower duct
1
Top gasket, lower duct
1
Grill gasket, lower duct
1
Back grill, lower duct
1
Side gasket, lower duct
2
Base cover, lower duct
1
Base gasket, lower duct
1
Drainage tube
1
M5x10 taptite screw
12–14
M5x12 screw
33–35
M10 hex nut
4
M5 hex nut
21–24
AN371942471353en-000101 / 136R02482 | Danfoss A/S © 2022.03
Overview
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

-
-
-
-
-
-
-
-
-
-
-
2 Installation
2.1 Safety Information
NOTICE
QUALIFIED PERSONNEL
Only qualified personnel are allowed to install the parts described in these installation instructions.
Disassembly and reassembly of the frequency converter must be done in accordance with the corresponding service guide.
Use the standard fastener torque values from the service guide, unless the torque value is specified in these instructions.
WARNING
ELECTRICAL SHOCK HAZARD
The frequency converter contains dangerous voltages when connected to mains voltage. Improper installation, and installing or
servicing with power connected, can cause death, serious injury, or equipment failure.
Only use qualified electricians for the installation.
Disconnect the frequency converter from all power sources before installation or service.
Treat the frequency converter as live whenever the mains voltage is connected.
Follow the guidelines in these instructions and local electrical safety codes.
WARNING
DISCHARGE TIME (20 MINUTES)
The frequency converter contains DC-link capacitors, which can remain charged even when the frequency converter is not pow-
ered. High voltage can be present even when the warning indicator lights are off.
Failure to wait 20 minutes after power has been removed before performing service or repair work can result in death or serious
injury.
Stop the motor.
Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and
DC-link connections to other frequency converters.
Wait 20 minutes for the capacitors to discharge fully before performing any service or repair work.
Measure the voltage level to verify full discharge.
NOTICE
ELECTROSTATIC DISCHARGE
Electrostatic discharge can damage components.
Ensure discharge before touching internal frequency converter components, for example by touching a grounded, conduc-
tive surface or by wearing a grounded armband.
AN371942471353en-000101 / 136R0248 | 3Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

-
2.2 Installation Overview
NOTICE
APPLYING GASKETS
This kit contains self-adhesive gaskets to ensure a proper seal between metal parts.
Before affixing a gasket, check that the part matches the gasket and that no holes are covered.
e30bj261.10
1
2
3
4
5
6
7
8
Illustration 2: Overview of In-bottom/Out-top Cooling Kit
1
Mounting holes
2
Top cover
3
Top cover gasket
4
Frequency converter
5
Lower duct
6
Cabinet backplate
7
Upper back vent
8
Lower back vent
AN371942471353en-000101 / 136R02484 | Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1.
2.
3.
2.3 Preparing the Mounting Plate
To create mounting holes and vent holes in the mounting plate, use the following steps. Refer to Illustration 3 for FA09 frequency
converters, and Illustration 4 for FA10 frequency converters.
Procedure
Drill 4 mounting holes in the mounting plate using the dimensions in the FA09 or FA10 template.
The holes must match the holes in the frequency converter.
Insert 4 M10 pem studs (not supplied) in the mounting holes.
Cut out the 2 vent openings in the mounting plate using the dimensions in the FA09 or FA10 template.
The openings must match the upper and lower duct openings.
844 (33.2)
2x Ø 8 (0.3)
Mounting Holes
e30bj160.10
699 (27.5)
200 (7.9)
130 (5.1)
140 (5.5)
4x Ø 5 (0.2)
214 (8.4)
180 (7.1)
7 (0.3)
78 (3.1)
122 (4.8)
10 (0.4) 110 (4.3)
68 (2.7)
7 (0.3)
78 (3.1)
122 (4.8)
6x Ø 8 (0.3)
2x Ø 8 (0.3)
Mounting Holes
177 (7.0)
214 (8.4)
228 (9.0)
Illustration 3: FA09 Mounting Plate Template for In-back/Out-back Cooling
AN371942471353en-000101 / 136R0248 | 5Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1.
2.
e30bj151.10
2x Ø 8 (0.3)
Mounting Holes
321 (12.6)
280 (11.0)
74 (2.9)
8x Ø 6 (0.2)
130 (5.1)
110 (4.3)
10 (0.4)
1051 (41.4)
896 (32.3)
140 (5.5) 180 (7.1)
271 (10.7)
295 (11.6)
328 (12.9)
16 (0.6)
2x Ø 8 (0.3)
Mounting Holes
29 (1.1)
4x Ø 7 (0.3)
Illustration 4: FA10 Mounting Plate Template for In-back/Out-back Cooling
2.4 Preparing the Backplate
To create vent openings in the cabinet backplate to match the openings in the mounting plate, use the following steps. Refer to
Illustration 5 for FA09 frequency converters and Illustration 6 for FA10 frequency converters.
Procedure
Cut out the vent openings in the cabinet backplate using the dimensions in the FA09 or FA10 template.
The openings must match the mounting plate openings.
Drill screw holes (6 mm) around the vent openings.
The FA09 requires 6 holes around each vent opening, and the FA10 requires 8 holes around each. The holes must align
with the holes in the outer flanges of the ducts.
AN371942471353en-000101 / 136R02486 | Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

246 (9.7)
13 (0.5)
10 (0.4)
188 (7.4)
6x Ø 7 (0.3)
167 (6.6)
652 (25.7)
215 (8.5)
6x Ø 7 (0.3)
10 (0.4)
236 (9.3)
266 (10.5)
e30bj066.10
Illustration 5: FA09 Cabinet Backplate Template for In-back/Out-back Cooling
AN371942471353en-000101 / 136R0248 | 7Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1.
2.
3.
4.
5.
6.
e30bj069.10
352 (13.8)
11 (0.4) 12 (0.5)
163 (6.4) 188 (7.4)
853 (33.6)
15 (0.6)
12 (0.5)
212 (8.3) 236 (9.3)
360 (14.2)
8x Ø 7 (0.3)
8x Ø 7 (0.3)
Illustration 6: FA10 Cabinet Backplate Template for In-back/Out-back Cooling
2.5 Installing the Top Cover
To install the top cover of the cooling kit, use the following steps. See Illustration 7.
Procedure
Remove the paper backing from the top cover gasket to expose the adhesive.
Adhere the top cover gasket to the underside of the top cover.
Remove 8 M5x14 screws (T25) surrounding the sides and back of the vent in the top of the frequency converter. Retain the
screws.
Remove 3 M5x12 screws (T25) at the front of the vent in the top surface of the frequency converter.
Slide the edge of the top cover under the 3 loosened screws, positioning the cover over the vent in the top of the frequen-
cy converter.
Secure the top cover to the frequency converter with the M5x14 screws (T25) removed previously in step 3.
Torque all screws to 2.3 Nm (20 in-lb).
AN371942471353en-000101 / 136R02488 | Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1
2
3
4
e30bj174.10
Illustration 7: Installation of the Top Cover
1
M5x14 screws
2
Top cover
3
Top cover gasket
4
Top vent
2.6 Mounting the Frequency Converter
To install the mounting plate and frequency converter in the Rittal cabinet, use the following steps. Refer to Illustration 8.
Procedure
Remove the backing paper from the 2 self adhesive upper mounting plate gaskets.
Affix the gaskets around the upper opening, 1 on each side of the mounting plate.
Remove the backing paper from the 2 self adhesive lower mounting plate gaskets.
Affix the gaskets around the lower opening, 1 on each side of the mounting plate.
Attach the mounting plate to the cabinet rails, making sure that the pem studs face the front of the cabinet.
Remove the backing paper from the 2 seal plate gaskets.
Affix the gaskets to the seal plates, 1 per plate.
Fasten 2 M10x30 screws through the seal plates, 1 per plate, and into the M10 nuts at the lower end of the mounting plate.
Check that the screws are secure. The base of the frequency converter rests on the screws.
Slightly lean the top of the frequency converter forward and set the notches in the base onto the 2 screws.
Slowly push the top of the frequency converter back against the mounting plate until the top 2 pem studs line up with the
holes in the frequency converter.
Secure the top of the frequency converter using 2 M10 nuts.
Torque all fasteners to 19 Nm (170 in-lb).
AN371942471353en-000101 / 136R0248 | 9Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

e30bj184.10
A
9
10
11 12
A
1
2
3
4
5
6
7
8
Illustration 8: Installation of the Frequency Converter in the Cabinet
1
Mounting plate
2
Mounting plate gasket (upper)
3
M10 nut
4
Frequency converter
5
Mounting plate gasket (lower)
6
Mounting holes
7
Mounting plate gasket (upper)
8
Mounting plate gasket (lower)
9
M10 nut
10
Seal plate gasket
11
Seal plate
12
Notch in lower edge of frequency converter
2.7 Assembling the Lower Duct
To assemble the lower duct, use the following steps. Refer to Illustration 9.
Procedure
AN371942471353en-000101 / 136R024810 | Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1.
2.
3.
4.
5.
6.
7.
8.
Peel the paper from the side gaskets, and press to attach the gaskets to the duct frame.
Align the holes in the side gaskets with the holes in the left and right sides of the back opening of the duct frame.
Place the grill over the left and right gaskets, with the threaded studs in the grill going through the middle holes in the
gasket and into the duct frame.
Secure the grill to the duct frame using 1 M5 nut on each stud.
Torque to 2.3 Nm (20 in-lb).
Affix the grill gasket to the outer side of the back grill.
Affix the duct base gasket to the duct base cover.
Secure the base cover to the underside of the duct frame with 12 M5 nuts (for FA09) or 14 M5 nuts (for FA10).
Torque to 2.3 Nm (20 in-lb).
Place the front gasket on the front side of the duct frame, making sure the holes in the frame and gasket align.
Affix the top gasket to the top of the duct frame.
Wait to attach the front duct cover until the lower duct assembly is installed in the cabinet.
1
2
3
4
5
6
7
8
9
10
e30bj172.10
Illustration 9: Assembly of Lower Duct
AN371942471353en-000101 / 136R0248 | 11Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1.
2.
3.
4.
1
Top gasket
2
Front gasket
3
M5 nut
4
Front cover
5
Grill gasket
6
Back grill
7
Side gaskets, left and right
8
Duct frame
9
Base gasket
10
Duct base cover
2.8 Installing the Lower Duct
To attach the lower duct to the frequency converter, use the following steps.
Procedure
Place the strip gasket over the 2 slots at the bottom back of the frequency converter.
Remove the cover and gasket from the bottom of the frequency converter by removing 7 screws.
Retain the screws, but discard the cover and gasket.
Secure the top flange of the duct to the bottom of the frequency converter using the screws removed in step 2.
Refer to Illustration 10. Torque screws to 2.3 Nm (20 in-lb).
Attach the front duct cover.
AN371942471353en-000101 / 136R024812 | Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1.
a.
b.
c.
d.
e.
1
2
3
4
5
e30bj173.10
6
Illustration 10: Installation of Lower Duct
1
Frequency converter
2
Holes for attaching duct
3
Lower duct
4
Screw
5
Top flange of duct
6
Front of duct
2.9 Installing the Back Vents
To install the upper and lower back vents, use the following steps. Refer to Illustration 11.
Procedure
To install the upper back vent, use the following steps:
Slide 6 clip-on nuts over the edge of the upper vent opening in the back plate of the cabinet.
Seat the clip-on nuts into the 6 holes around the opening.
Affix 2 upper vent gaskets to the flange of the upper back vent, placing 1 gasket on the inner side and 1 gasket on
the outer side of the flange.
Slide the upper back vent into the opening in the back plate.
Fasten 6 M6x12 screws around the inner edge of the upper back vent.
AN371942471353en-000101 / 136R0248 | 13Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

f.
2.
a.
b.
c.
d.
e.
f.
Secure the M5x18 screws in the flange of the upper back vent, attaching the vent to the back plate.
Use 6 screws for the FA09 frequency converter, and 8 screws for the FA10 frequency converter.
To install the lower back vent, use the following steps.
Slide 6 clip-on nuts over the edge of the lower vent opening in the back plate of the cabinet.
Seat the clip-on nuts into the 6 holes around the opening.
Affix 2 lower vent gaskets to the flange of the lower back vent, placing 1 gasket on the inner side and 1 gasket on
the outer side of the flange.
Slide the lower back vent into the opening in the back plate.
Fasten 4 M6x12 screws around the inner edge of the lower back vent.
Secure the M5x18 screws in the outer flange of the lower back vent, attaching the vent to the back plate.
Use 6 screws for the FA09 frequency converter, and 8 screws for the FA10 frequency converter.
1
2
3
4
5
6
7
8
9
10
11
12
e30bj181.10
Illustration 11: Installation of Upper and Lower Back Vents
AN371942471353en-000101 / 136R024814 | Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

1
Clip-on nut
2
Upper vent gasket (inner)
3
Upper back vent
4
Upper vent gasket (outer)
5
M6x12 screw
6
M5x18 screw
7
Lower vent gasket (inner)
8
Lower back vent
9
Lower vent gasket (outer)
10
M5x18 screw
11
M6x12 screw
12
Clip-on nut
AN371942471353en-000101 / 136R0248 | 15Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide

Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
danfossdrives.com
Any information, including, but not limited to information on selection of product, its application or use, product design, weight, dimensions, capacity or any other tech-
nical data in product manuals, catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or via download, shall be
considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility
for possible errors in catalogues, brochures, videos and other material.
Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without
changes to form, fit or function of the product.
All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved.
*136R0248*
*M00311* AN371942471353en-000101 / 136R024816 | Danfoss A/S © 2022.03
Installation
In-back/Out-back Cooling Kit for FA09-FA10
Installation Guide