DAQ system EMB-OPT02 User manual

EMB-OPT02
User Manual
Version 1.0
ⓒ2005 DAQ SYSTEM Co., Ltd. All rights reserved.
Microsoft®is a registered trademark; Windows®, Windows NT®, Windows XP®, Windows 7®, Windows 8®, Windows 10®
All other trademarks or intellectual property mentioned herein belongs to their respective owners.
Information furnished by DAQ SYSTEM is believed to be accurate and reliable, However, no responsibility is assumed by DAQ SYSTEM for its use, nor
for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under
any patent or copyrights of DAQ SYSTEM.
The information in this document is subject to change without notice and no part of this document may e copied or reproduced without the prior
written consent.

EMB-OPT02 User’s Manual
1
Contents
1. EMB-OPT02 Introduction --------------------------------------------------------- 2
2. EMB-OPT02 Function ------------------------------------------------------------ 4
2-1 J1 Connector ----------------------------------------------------------------- 5
2-2 JP1 Connector --------------------------------------------------------------------- 7
2-3 SW1 Switch --------------------------------------------------------------------- 7
2-4 SW3 Switch -------------------------------------------------------------------- 8
2-5 CN1(SFP) Connector ---------------------------------------------------------------- 8
2-7 Fiber Cable -------------------------------------------------------------------- 10
Appendix
A-1 Board Size --------------------------------------------------------------- 12
A-2 Repair Regulations -------------------------------------------------------------- 13

EMB-OPT02 User’s Manual
2
1. EMB-OPT02 소개
The EMB-OPT02 board converts the parallel (D0..D47) data signal of the J1 connector into an optical
signal and outputs it.
[Figure 1-1] shows an example of using the EMB-OPT02 board, which converts the image signal from
the CameraLink camera into light and transmits it to the PCIe-OPT02 board, which is the light receiving
board. 1 Base Camera Link configuration is supported.
[Figure 1-1. EMB-OPT02와PCIe-OPT02 Connection]
Reference) The most important factor in selecting an optical cable is the communication distance.
A multimode cable provides a maximum transmission distance of 2Km, and a single-
mode cable basically provides a transmission distance depending on the type of
equipment. Communication using light basically uses 2Core. (RX-1 CORE, TX-1 CORE)
Therefore, be careful when connecting the board with a 2 core optical cable as shown
in the figure below.

EMB-OPT02 User’s Manual
3
Fiber Cable
Connection
Caution) Be careful not to twist the cable when connecting it to the SFP cage.

EMB-OPT02 User’s Manual
4
2. EMB-OPT02 Function
Each name and function description of EMB-OPT2 is as follows.
DAQ system
EMB-OPT02 Board
EMB-OPT02REV. A
CN1
D7
JP1
www.daqsystem.com
ON
1 2
SW3
3 4
D10
U1
SW2
U3
J1
U2
U4
J3
J2
D5
D6
D8
D9
[그림 2-1. EMB-OPT01 Layout]
[Table 1. EMB-OPT02 main function description]
No.
Name
Description
1
J1
Camera Link / DIO_IN0..47 Connector
2
U1, U3
1.2V, 1.8V, 3.3V Output
3
U2
FPGA
4
CN1
SFP(Small Form Factor Pluggable) Connector
5
U4
Serial Memory
6
JP1
12V Circular DC Jack
7
SW2
12V Power Switch
8
SW3
Connection mode selection switch
The LED shows the inner workings.
LED D5 : Detects Pclk (Pixel Clock) signal.
LED D6 : Detects Lval (Line Valid) signal.
LED D7 : Lights up when power is supplied to the board and initialization is completed.
LDE D8 : Detects Dval (Data Valid) signal.
LED D9 : Vsync (Vertical Sync.) /16 division signal
LED D10 Red is On when optical is connected.
LED D10 Green turns on when the optical channel (#0) horizontal sync signal (Hsync) is detected.

EMB-OPT02 User’s Manual
5
2-1 J1 Connector
The figure below shows the pin map of the J1 connector.
2
69
70
[Figure 2-2. EMB-OPT02 J1 Connector Pin-out]
[Table 2. J1 Connector]
No.
Name
Description
Remark
1
3.3V
3.3V Power
2
12V
12V Power
3
DIO_IN0
Digital In/Out Data 0
4
DIO_IN1
Digital In/Out Data 1
5
DIO_IN2
Digital In/Out Data 2
6
DIO_IN3
Digital In/Out Data 3
7
DIO_IN4
Digital In/Out Data 4
8
DIO_IN5
Digital In/Out Data 5
9
DIO_IN6
Digital In/Out Data 6
10
DIO_IN7
Digital In/Out Data 7
11
DIO_IN8
Digital In/Out Data 8
12
DIO_IN9
Digital In/Out Data 9
13
DIO_IN10
Digital In/Out Data 10
14
DIO_IN11
Digital In/Out Data 11
15
DIO_IN12
Digital In/Out Data 12
16
DIO_IN13
Digital In/Out Data 13
17
DIO_IN14
Digital In/Out Data 14
18
DIO_IN15
Digital In/Out Data 15
19
DIO_IN16
Digital In/Out Data 16
20
DIO_IN17
Digital In/Out Data 17
21
DIO_IN18
Digital In/Out Data 18
22
DIO_IN18
Digital In/Out Data 19
23
DIO_IN20
Digital In/Out Data 20
24
DIO_IN21
Digital In/Out Data 21
25
DIO_IN22
Digital In/Out Data 22
26
DIO_IN23
Digital In/Out Data 23
27
Ground
28
Ground

EMB-OPT02 User’s Manual
6
29
DIO_IN24
Digital In/Out 24
30
DIO_IN25
Digital In/Out 25
31
DIO_IN26
Digital In/Out 26
32
DIO_IN27
Digital In/Out 27
33
DIO_IN28
Digital In/Out 28
34
DIO_IN29
Digital In/Out 29
35
DIO_IN30
Digital In/Out 30
36
DIO_IN31
Digital In/Out 31
37
DIO_IN32
GPIO00
38
DIO_IN33
GPIO01
39
DIO_IN34
GPIO02
40
DIO_IN35
GPIO03
41
DIO_IN36
GPIO04
42
DIO_IN37
GPIO05
43
DIO_IN38
GPIO06
44
DIO_IN39
GPIO07
45
DIO_IN40
GPIO08
46
DIO_IN41
GPIO09
47
DIO_IN42
GPIO10
48
DIO_IN43
GPIO11
49
DIO_IN44
GPIO12
50
DIO_IN45
GPIO13
51
DIO_IN46
GPIO14
52
DIO_IN47
GPIO15
53
Ground
54
Ground
55
LVAL
Line Valid
56
FVAL
Frame Valid
57
DVAL
Data Valid
58
PCLK
Pixel Clock
59
Ground
60
Ground
61
CC_D0
Camera Control output 0
62
CC_D1
Camera Control output 1
63
CC_D2
Camera Control output 2
64
CC_D3
Camera Control output 3
65
Ground
66
Ground
67
DTX
Serial to Frame grabber-
68
DRX
Serial to Camera+

EMB-OPT02 User’s Manual
7
69
I2C_SDA
I2C Serial Data
70
I2C_SCL
I2C Serial Clock
2-2 JP1 Connector
This is an external 12V DC Jack power connector. (HR10-7R-6S-RA)
[Figure 2-3. Rated power]
2-3 SW1 Switch
It is an option select switch.
SWITCH 3
OFF : Vsync
ON : Reverse Vsync
SWITCH 4
OFF : Dval Use
ON : Dval not use
SWITCH #2, #4 ~ #8 : Reserved

EMB-OPT02 User’s Manual
8
2-4 SW3 Switch
It is a 12V DV external power switch.
+12V
V_IN_12V
SW_T_SPOT
[Figure 2-4. SW3]
2-5 CN1(SFP) Connector
In the case of EMB-OPT02, an SFP (Small Form Factor Pluggable) connector is used as a
Fiber-Transmission Transceiver device. The SFP transceiver is designed to support various optical
transmissions such as SONET, Gigabit Ethernet, and Fiber Channel. It supports hot-pluggable
transceiver and can be connected to network device motherboard with fiber or copper
networking cable.
SFP is connected to the module that connects to the cage and connector, and there are Tx
(Transceiver) and Rx (Receiver) together.
[Figure 2-5. SFP & SFP Cage]

EMB-OPT02 User’s Manual
9
[Table 3. CN1 SFP Connector]
No.
Name
Description
Remark
1
VeeT
Transmitter Ground
2
TxFault
Transmitter Fault
3
TxDisable
Transmitter Disable
4
SDA
Serial Interface Data Line
5
SCL
Serial Interface Clock
6
MOD-ABS
Module Absent, connected to VeeT or VeeR
7
RS0
Rx Rate Select
Open or Low = 2.125 or 4.25 Gb/s Fibre Channel (Low
Bandwidth)
High = 8.5 Gb/s Fibre Channel (High Bandwidth)
8
LOS
When high, indicates received optical power below
worst-case receiver sensitivity.
9
RS1
Tx Rate Select
Open or Low = 2.125 or 4.25 Gb/s Fibre Channel (Low
Bandwidth)
High = 8.5 Gb/s Fibre Channel (High Bandwidth)
10
VeeR
Receiver Ground
11
VeeR
Receiver Ground
12
RD-
Receiver Data
13
RD+
Receiver Inverted Data
14
VeeR
Receiver Ground
15
VccR
Receiver Power(3.3V)
16
VccT
Transmitter Power(3.3V)
17
VeeT
Transmitter Ground
18
TD+
Transmitter Data
19
TD-
Transmitter Inverted Data
20
VeeT
Transmitter Ground
(Note) For detailed specifications, refer to the Camera Link standard document.

EMB-OPT02 User’s Manual
10
2-6 Fiber Cable
An optical cable is a transmission cable made to transmit the converted laser signal to a long
distance and uses two transmission modes.
Single Mode : It is used for broadband and long-distance transmission with a core diameter of
9㎛, and it is possible to transmit without relay up to about 50Km. In the case of
single-mode with a small core diameter, it is difficult to transmit a large amount of
information because the cable passage is narrow, but instead it can be transmitted
over a long distance. The cable color is mainly yellow.
Multi Mode : The core diameter is 50~100 ㎛, so it is often used in short distances. In the case
of multimode with a large core diameter, a large amount of information can be
transmitted because the passage of the cable is wide, and the color of the cable is
mainly orange.
Optical connectors include LC, ST, MTRJ, SC, FC, and MU types, but EMB-OPT02 mainly uses
multimode LC type as shown in [Figure 2-7].
[Figure 2-6. Signal transmission method according to transmission mode]

EMB-OPT02 User’s Manual
11
(1) Single Mode LC Type (2) Multi Mode LC Type
[Figure 2-7. Cable type according to transmission mode]

EMB-OPT02 User’s Manual
12
Appendix
A-1 Board Size
The external sizes of the board are as follows. (65 x 69mm)
< Top View >
69
65

EMB-OPT02 User’s Manual
13
A-2 Repair Regulations
Thank you for purchasing a DAQSYSTEM product. Please refer to the following regarding
Customer Service regulated by DAQSYSTEM.
(1) Read the user manual and follow the instructions before using the DAQSYSTEM product.
(2) When returning the product to be repaired, please write down the symptoms of the failure and
send it to the head office.
(3) All DAQSYSTEM products have a 1-year warranty.
-. Warranty period counts from the date the product is shipped from DAQSYSTEM.
-. Peripherals and third-party products not manufactured by DAQSYSTEM are covered by the
manufacturer's warranty..
-. If you need repairs, please contact the Contact Point below..
(4) Even during the warranty period, repairs are charged in the following cases..
①Failure or damage caused by use without following the user's manual
②Failure or damage caused by customer's negligence during product transportation after
purchase
③Failure or damage caused by natural phenomena such as fire, earthquake, flood, lightning,
pollution, or power supply exceeding the recommended range
④Failure or damage caused by inappropriate storage environment (e.g. high temperature, high
humidity, volatile chemicals, etc.)
⑤Breakdown or damage due to unreasonable repair or modification
⑥Products whose serial number has been changed or removed intentionally
⑦If DAQSYSTEM determines that it is the customer's fault for other reasons
(5) Shipping costs for returning the repaired product to DAQSYSTEM are the responsibility of the
customer.
(6) The manufacturer is not responsible for any problems caused by misuse, regardless of our
warranty terms.

EMB-OPT02 User’s Manual
14
MEMO
Contact Point
Web sit : https://www.daqsystem.com
Email : [e-mail]