Data Video SE-1200MU User manual

1

2
Table of Contents
Warnings and Precautions.................................................................................................................................5
Warranty ............................................................................................................................................................6
Standard Warranty.........................................................................................................................................6
Two Year Warranty ........................................................................................................................................6
Disposal ..............................................................................................................................................................6
Chapter 1 Introduction.....................................................................................................................................7
1.1 Features...............................................................................................................................................7
1.2 System Diagram...................................................................................................................................8
Chapter 2 Hardware Connections ....................................................................................................................9
2.1 Front Panel ..........................................................................................................................................9
2.2 Rear Panel ...........................................................................................................................................9
Chapter 3 Network Setup...............................................................................................................................11
3.1 Initial SE-1200 MU Setup with a Windows Computer ......................................................................11
3.2 Installing the SE-1200 MU Controller Software to a Windows Computer .......................................12
3.2.1 Router Based DHCP Setup .............................................................................................................13
3.2.2 How to control the SE-1200 MU from another building or city ................................................14
3.2.3 Setting the Target IP Address with the Controller Software .....................................................15
Chapter 4 SE-1200 MU Video Setup...............................................................................................................17
4.1 SE-1200 MU Multi View Output........................................................................................................17
4.2 Setting the Video Outputs.................................................................................................................18
4.3 Setting the Video Standard ...............................................................................................................18
4.4 SE-1200 MU Video Layers .................................................................................................................19
Chapter 5 Video Connection Setup ................................................................................................................21
5.1 Inputs – Setup ...................................................................................................................................21
5.1.1 Crosspoint ..................................................................................................................................21
5.1.2 Source Labels .............................................................................................................................21
5.2 Setting up the SE-1200 MU Video Stream Based Multi View ...........................................................21
5.2.1 Preparing the SE-1200 MU Stream Output ...................................................................................22
5.2.2 VLC Media Player - Stream Caching...........................................................................................23
5.2.3 Port Forwarding for the SE-1200 MU ............................................................................................23
Chapter 6 PC Control Panel ............................................................................................................................24
6.1 Sources Panel ....................................................................................................................................24
6.1.1 AUX BUS .....................................................................................................................................24

3
6.1.2 PROGRAM ..................................................................................................................................24
6.1.3 PRESET........................................................................................................................................24
6.2 TRANSITION CONTROLS Panel ...............................................................................................................25
6.2.1 Previewing a Selected Transition/Wipe ........................................................................................25
6.2.2 Rev and Nrm (NORM) / Rv (REV) Buttons .....................................................................................25
6.2.3 Key 1 & Key 2 PRIORITY Key Function ...........................................................................................25
6.3 Transition Effects...............................................................................................................................26
6.3.1 CUTTING between Sources............................................................................................................26
6.3.2 Mixing between Sources ...............................................................................................................26
6.3.3 Wiping between Sources...............................................................................................................27
6.3.4 Clip between Sources (Stinger Transition).................................................................................28
6.4 FTB Key Function ...............................................................................................................................30
6.4.1 Enable ............................................................................................................................................30
6.4.2 FTB .................................................................................................................................................30
6.5 DSK TRANS Panel...............................................................................................................................30
Chapter 7 Applications ...................................................................................................................................31
7.1 Luma Key - Quick DSK 1 Setup ..........................................................................................................31
7.1.1 Keyer Control.................................................................................................................................32
7.1.2 Keyer Matte ...................................................................................................................................33
7.2 Linear key - Quick DSK 2 Setup..........................................................................................................33
7.3 Picture in Picture (PinP) Function .....................................................................................................35
7.3.1 PIP Position....................................................................................................................................36
7.3.2 PIP Border......................................................................................................................................36
7.3.3 PIP Crop .........................................................................................................................................37
7.4 Bus MATTE Setup ..............................................................................................................................37
7.5 Clips – Quick Setup............................................................................................................................38
Chapter 8 CHROMA Key Functions.................................................................................................................41
8.1 Overview ...........................................................................................................................................41
8.2 Chroma Matte ...................................................................................................................................42
8.3 Chroma Key Ctrl.................................................................................................................................43
8.4 Color Spill...........................................................................................................................................43
8.5 Chroma Key - Setup...........................................................................................................................44
8.6 Key MASK Function ...........................................................................................................................45
Chapter 9 Freezing a Video Input for Stills Capture.......................................................................................46

4
9.1 Stills – Grab and Save ........................................................................................................................46
9.2 Assigning a Saved Still Image to an Input Channel............................................................................47
9.3 Exporting and Importing Stills...........................................................................................................48
Chapter 10 USER Memory Functions............................................................................................................50
10.1 Saving the Current Settings to a User Memory Slot .........................................................................50
10.2 Labelling an Existing User Memory Slot............................................................................................51
10.3 Loading a Previously Saved User Setup ............................................................................................52
10.4 Deleting a User Setup........................................................................................................................53
10.5 Exporting and Importing User Setups ...............................................................................................53
Chapter 11 Appendices.................................................................................................................................55
Appendix 1: Audio ........................................................................................................................................55
Appendix 2: GPI Out.....................................................................................................................................55
Appendix 3: Firmware Upgrade ...................................................................................................................56
Appendix 4: Dimensions...............................................................................................................................57
Appendix 5: Specifications ...........................................................................................................................58
Service and Support.........................................................................................................................................60
Disclaimer of Product and Services
The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to
give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this
manual, from time to time, may not be correct or may be incomplete. This manual may contain typing errors, omissions or
incorrect information. Datavideo Technologies always recommend that you double check the information in this document for
accuracy before making any purchase decision or using the product. Datavideo Technologies is not responsible for any omissions
or errors, or for any subsequent loss or damage caused by using the information contained within this manual. Further advice on
the content of this manual or on the product can be obtained by contacting your local Datavideo Office or dealer.

5
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe
and reliable operation of this unit, and to protect it from overheating, do not block or cover these
openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on
the bottom of the cabinet will be blocked. This unit should never be placed near or over a heat register
or radiator. This unit should not be placed in a built-in installation unless proper ventilation is provided.
7. This product should only be operated from the type of power source indicated on the marking label of
the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or
your local power company.
8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be
walked on, rolled over, or otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the
products plugged into the extension cord do not exceed the extension cord rating.
10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not
exceed 15 amperes.
11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch
dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill
liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not attempt to service this product
yourself. Opening or removing covers that are marked “Do Not Remove” may expose you to dangerous
voltage points or other risks, and will void your warranty. Refer all service issues to qualified service
personnel.
13. Unplug this product from the wall outlet and refer to qualified service personnel under the following
conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions. Adjust only those
controls that are covered by the operating instructions in this manual; improper adjustment of
other controls may result in damage to the unit and may often require extensive work by a
qualified technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f. When the product exhibits a distinct change in performance, indicating a need for service.

6
Warranty
Standard Warranty
•Datavideo equipment is guaranteed against any manufacturing defects for one year from the date
of purchase.
•The original purchase invoice or other documentary evidence should be supplied at the time of any
request for repair under warranty.
•Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered by this
warranty.
•All mail or transportation costs including insurance are at the expense of the owner.
•All other claims of any nature are not covered.
•Cables & batteries are not covered under warranty.
•Warranty only valid within the country or region of purchase.
•Your statutory rights are not affected.
Two Year Warranty
•All Datavideo products purchased after 01-Oct.-2008 qualify for a free one
year extension to the standard Warranty, providing the product is
registered with Datavideo within 30 days of purchase. For information on
how to register please visit www.datavideo.com or contact your local
Datavideo office or authorized Distributors
•Certain parts with limited lifetime expectancy such as LCD Panels, DVD Drives, Hard Drives are only
covered for the first 10,000 hours, or 1 year (whichever comes first).
Any second year warranty claims must be made to your local Datavideo office or one of its authorized
Distributors before the extended warranty expires.
Disposal
For EU Customers only - WEEE Marking
This symbol on the product indicates that it will not be treated as household waste. It
must be handed over to the applicable take back scheme for the recycling of Waste
Electrical and Electronic Equipment. For more detail
ed information about the
recycling of this product, please contact your local Datavideo office.

7
Chapter 1 Introduction
The Datavideo SE-1200 MU is a small, cost-effective, HD digital video switcher with easy-to-use
professional features. The SE-1200 MU can be controlled over a network and can even display a multi view
over the same network connection. This allows the SE-1200 MU operator to have the option of working in
a different room, or a different building, or even a different city!
The SE-1200 MU switcher offers four HD SDI and two HDMI inputs. Supported video formats include
1080i/50, 1080i/59.94, 1080i/60, 720p/50, 720p/59.94 and 720p/60. Output options include; two user
assignable HD SDI and two HDMI outputs. These user defined output options can be set up to provide
Clean Preview, Clean Program, Program with DSK overlay, Preview Out or Multi-view as well as Inputs 1~6.
The SDI or HDMI outputs can be taken to other Datavideo products (separate purchase) such as the HDR-
70 HD recorder, TLM-170G HD monitor and can also be streamed to web based viewers using the
Datavideo NVS-25 Video Streaming Server.
The SE-1200 MU also features two analogue balanced XLR audio inputs for connecting an external audio
mixer such as the Datavideo AM-100 or AD-200. Tally and RJ-45 connections allow the switcher to be
connected to a Windows PC as well as providing tally light indications to crew and on screen talent via
Datavideo’s ITC-100 talkback system.
The SE-1200 MU is also capable of HD Chroma Key, Luma Key, Down Stream Key, Picture In Picture, up to
32 Wipe transitions and user defined still frame stores. In addition, it also allows the user to connect an
external physical switcher keyboard controller such as Datavideo’s RMC-260. It really is a small, powerful,
HD video switcher!
1.1 Features
•6 video inputs ( SDI x 4 + HDMI x 2)
-Frame Sync on each input
•Flexible Mix/Effects Processor with
-HD Chroma Key / Linear / Luma Key
-Picture-In-Picture
-Wipe Generator with 32 wipe patterns including circle and heart wipes plus Border &
Softness Controls
-Traditional Mix & Cut Transitions
-User defined Down Stream Key for use with external CG text overlay
-Full M/E Preview function
•Frame store
-Dedicated Stills Buffer
-Up to 1000 images can be stored internally
-The dedicated Frame Stores allow easy recall of three previously loaded images
•Assignable Outputs (SDI & HDMI)
•XPT (Cross Point Assignment)
•PC control and setup available over a standard RJ-45 IP connection
•Tally output compatible with Datavideo ITC-100 talk back system
•GPI Output
•Supports physical switcher keyboard controller such as RMC-260

8
1.2 System Diagram

9
Chapter 2 Hardware Connections
2.1 Front Panel
Power ON /OFF switch
2.2 Rear Panel
Video IN
The SE-1200 MU is equipped with six video input channels.
V
ideo Input set is comprised of four SDI connectors and two HDMI
ports.
Video OUT
HDMI 1 and the two SDI outputs can be used for monitoring video
in a number of different configurations
including Program,
Preview and or Multi-view. See Section 4.2.
HDMI 2: Multi-view Output ONLY
Note: Both HDMI output ports operate at 1080
p or 720p
depending on the chosen video standard.
Audio Input
Supports four channels XLR Balanced Audio Input.
GPI
GPI output connection for basic control of other externally-
connected devices.

10
Ethernet Ports
For connection of the Main Unit to the PC such that the SE-1200
MU can be remotely controlled on a graphical user interface.
RS-232
For remote control interface such as RMC-260.
TALLY Output
The SE-1200 MU Tally Output Port provides bi-colour tally
information (Red and Amber); Red indicates On-Air and Amber
indicates next camera source.
DC IN
Connect the supplied 12V / 19W PSU to this socket. The
connection can be secured by screwing the outer fastening ring of
the DC In plug to the socket.
Grounding Terminal
When connecting this unit to any other component, make sure
that it is properly grounded by connecting this terminal to an
appropriate point. When connecting, use the socket and be sure to
use wire with a cross-sectional area of at least 1.0 mm2.

11
Chapter 3 Network Setup
3.1 Initial SE-1200 MU Setup with a Windows Computer
The SE-1200 MU switcher is not supplied with a traditional hardware based control panel. Instead it is
controlled using a software user interface installed on your Windows-based computer. When new from
the factory the unit will initially have a static IP address of 192.168.100.101.The unit can be directly
connected to a Windows-based computer using an RJ-45 ethernet cable. The following set up should allow
you to initially configure the unit before moving it to an existing DHCP / LAN network.
•An RJ-45 ethernet cable.
•Windows 7/8 laptop or PC.
•The Datavideo SE-1200 MU controller
software.
Instructions
1. First connect the SE-1200 MU and the Windows computer together using an RJ-45 ethernet cable.
2. Turn on the Windows computer and set it to static IP set up within the Windows Network and
Sharing Centre.
In our example the computer is given the following IP settings so that the computer matches the
same IP range as the switcher.
3. Now install the supplied SE-1200 MU controller software to the computer.

12
3.2 Installing the SE-1200 MU Controller Software to a Windows Computer
The SE-1200 MU can be connected to a simple IP network and controlled using Windows-based software. If
you have not already set up the SE-1200 MU with a computer then please follow the instructions on the
previous page.
The SE-1200 MU comes with an accessory software CD. If this CD has been lost or has not been supplied
then please download the latest software from the Datavideo SE-1200 MU web page. See:
www.datavideo.com
The install executable file [.exe] will be called Se1200 Control v.x.x.x.x
The v.x.x.x.x represents the latest version number.
Double click this .exe file then follow the on screen install wizard prompts.
Once installed launch the SE-1200 MU controller software.
The SE-1200 MU controller software has a built-in IP finder, which is designed for PC with multiple Ethernet
cards or DHCP network environment. Please note IP finder can only find devices that are on the same
network domain as the PC. If you cannot remember your device IP, please contact your local Datavideo
distributor for assistance as there is currently no reset function for network settings. Upon launch of the
SE-1200 MU controller software, you will be prompted to select one Ethernet Interface Card.
Once selected, click OK to start the scanning process.
If the SE-1200 MU control software cannot find the SE-1200 MU device, the software will continuously
prompt you for an appropriate interface card. Again, please make sure the selected interface card is on the
same network domain as the SE-1200 MU device.
Once the SE-1200 MU device is found, the software will connect with the switcher hardware over the IP set
up described on the previous page.

13
As the program buttons are clicked the SE-1200 MU program output and multi view output will show
changes.
3.2.1 Router Based DHCP Setup
The computer software can also access and control the SE-1200 MU over an existing TCP/IP LAN type
network. In order to initially set up the SE-1200 MU, you may need the assistance of your local I.T.
specialist to help with the network settings. To help guide you, we have included a simplified network set
up example below, further advice may be available through your dealer locally or your Datavideo regional
office.
To create this simple dedicated SE-1200 MU IP network you will need:
•An IP router which can assign/give IP
addresses.
•Two RJ-45 patch leads.
•Windows 7/8 laptop or PC.
•The IP router Administrator login and
password.
•The Datavideo SE-1200
MU controller software.

14
Instructions
1. First connect the router to the SE-1200 MU and the Windows computer using two RJ-45 patch leads.
2. Turn on the Windows computer and set it to DHCP setup within the Windows Network and Sharing
Centre.
3. Now click the Windows start button and run the CMD prompt window.
4. At the command line > : _ type IPCONFIG and press enter.
5. The DEFAULT GATEWAY number displayed should be the router’s current IP address.
6. Enter the DEFAULT GATEWAY IP address into the address bar of the computer’s web browser.
7. The web browser should display the login window for the router. Enter the router’s login and/or
password.
The login details may be written on a sticker on the router itself or noted in the manual for the router.
8. Once logged into the router we need to change the router to supply IP addresses in the
192.168.100.xxx range. Use the router’s LAN Setup or Configure LAN option to set the router’s IP
address as 192.168.100.1 and click save / apply.
9. Now reboot the router and power ON the SE-1200 MU.
10. Log into the router again using the web browser and the router’s new IP address 192.168.100.1
11. Use the router’s LAN Setup or Configure LAN option again, within this option there should be another
option called Address Reservation or Client List.
12. The two devices connected to the router should be listed here, the computer and the SE-1200 MU.
13. The computer, because it is set for DHCP, will already have an IP address automatically assigned to it in
this list.
14. The SE-1200 MU may only show its MAC address (1E:ED:19:27:1A:B3). Copy and Paste the SE-1200
MU’s MAC address into the MAC address reservation box. Now enter the following IP address
192.168.100.101 into the reservation box next to the SE-1200 MU’s MAC address.
15. The router should now give the IP address 192.168.100.101 to the SE-1200 MU when it is connected to
the router.
16. Click save / apply then reboot the router again.
17. Close the web browser and CMD windows.
18. Now install the supplied SE-1200 MU control software to the computer.
3.2.2 How to control the SE-1200 MU from another building or city
Once you are familiar with the SE-1200 MU you may want to control the switcher from another building or
even a different city. This requires certain internet and network access that may not already be present at
both sites.
Note: It is best to discuss your planned SE-1200 MU set up beforehand with your local I.T. or network
support manager as this process will involve ‘opening’ or ‘forwarding’ TCP/IP ports.
To create this dedicated SE-1200 MU IP set up you will need:
•Two sites with internet access. We will call these site A and site B.
•Site A will have the same SE-1200 MU set up as Section 3.1 but with no local computer connected.
•Site B will have a Windows 7/8 computer connected to the internet with VLC Player and the
Controller software.
•Port 5000 will allow streaming of the SE-1200 MU multi view from site A to VLC Player at site B.

15
•Incoming commands on Ports 5003 and 5004 at Site A will be port forwarded to the internal
private IP address of Datavideo SE-1200 MU at site A to allow control from site B.
•The Public IP address for site A needs to be discovered, this will be used as the Target IP address
for both VLC player and the SE-1200 MU Controller software at site B.
3.2.3 Setting the Target IP Address with the Controller Software
Click Setup in the MENU SELECT panel and the current IP Network settings are shown alongside the
software version.

16
If the network settings are wrong then you may not be able to control the SE-1200 MU. Always keep a note
of the last IP settings used and change these settings carefully to avoid problems.
Target IP address – This IP address is the location on the local network, or the internet, where the software
can talk to the SE-1200 MU. By clicking on Target IP address you can enter a new address, once entered
click Save Setup. The next time the software controller is opened, it will try to contact the switcher on this
new Target IP address.
Network – This option in the yellow menu column allows you to change the network options on the SE-
1200 MU. When delivered from the factory the default static IP settings should be:
Set up: Static (a manually set IP address that does not change even after power cycling the SE-1200
MU unit)
IP address: 192.168.100.101
Subnet Mask: 255.255.255.0
Gateway:192.168.100.1
DHCP set up - If the IP set up method is changed to DHCP then each time the SE-1200 MU is started, it may
be given a different IP address by the network. Only use this method if you know how to find the SE-1200
MU on the internal IP network. A device on the network (usually a router or server) will automatically give
a spare or fixed IP address to the SE-1200 MU. The other settings such as IP address, Subnet Mask and
Gateway may appear blank within the controller software as these would be automatically set by network
router/DHCP server.

17
Chapter 4 SE-1200 MU Video Setup
4.1 SE-1200 MU Multi View Output
The SE-1200 MU multi view output can be supplied locally, from either the HDMI1 or SDI outputs 1 and 2
on the units rear panel, see section 2.2 (Chapter 2). The multi view can also be streamed over a
LAN/internet connection, see section 3.2.2 (Chapter 3).
The default multi view output, when new, is from HDMI output 1. This HDMI output operates at 1080P or
720P depending on the video standard chosen, see section 4.3 (Chapter 4).
The Multi view shows monitoring images for Preview (PVW), Program (PGM), Inputs 1~6, as well as SDI
outputs 1 and 2.
The SE-1200 MU can also show audio level bars overlaid on the Program image within the multi view. This
confirms if analogue XLR audio input is being received and embedded to the selected Program output(s).
A Red tally indication box is shown around the selected Program source(s). This video image is also seen at
the switchers selected Program output(s). A Green tally indication box is shown around the selected
Preview source. This will be the image source to be mixed to, wiped in, or cut to next depending on the
user’s preference.
Images SDI out 1 and SDI out 2 confirm what is being sent from those SDI outputs. These outputs can be
configured differently by the user, see section 5.2.1 (Chapter 5).

18
4.2 Setting the Video Outputs
These rear panel video outputs are initially set as follows when shipped from the factory.
SDI 1 Factory default – Program out with DSK
SDI 2 Factory default – Program out with DSK
HDMI 1 Factory default – Multi view output
HDMI 2 Not currently supported – system folder view only
Each of the outputs can be reconfigured to one of the settings below by using the menu option Outputs
1: Multiview
2: PGM Out
3: PVW Out
4: PGM DSK1
5: PVW DSK1
6: Clean PGM
7: Clean PVW
8: Input 1
9: Input 2
10: Input 3
11: Input 4
12: Input 5
13: Input 6
Note: Ensure at least one output is left set as Multi View so the Main Menu can still be accessed.
Note: The SE-1200 MU HDMI multi view output only operates at the 1080P or 720P standards. This can be
useful for some HDMI and DVI monitor types. If an interlaced 1080i Multi view output is needed please
configure an SDI output for multi view as shown above.
4.3 Setting the Video Standard
The SE-1200 MU video standard can be
changed by using the menu path SETUP >
STANDARD.
The SE-1200 MU is initially set up for the
1920 x 1080 i50 or i60 video standard when
shipped from the factory depending on your
country’s video standard.
As with most HD video switchers, the SE-
1200 MU will expect all video inputs to be
operating at the same video standard as the
switcher itself. If a connected device is
supplying a different video format/standard then the switcher may not display the video for that input.
Change the source equipment settings to match the switcher’s video standard or vice versa.

19
The SE-1200 MU can support the following HD video standards: 1080i/50, 1080i/59.94, 1080i/60 and
720p/50, 720p/59.94, 720p/60.
4.4 SE-1200 MU Video Layers
The SE-1200 MU is a High Definition Digital Video Switcher and as well as mixing video sources and
embedding analogue audio, it has additional functions such as Picture in Picture (PIP), Chroma Key, Luma
Key and Down Stream Key (DSK).
Before attempting to use the SE-1200 MU’s PIP, Chroma, Luma and Down Stream Keying functions, it may
help to first understand the order of the video layers at the SE-1200 MU Program outputs.
The background video layer is used for transitioning between Preview and Program sources. This layer also
includes any selected wipe transitions. This layer can be hidden or partly hidden by the PiP, Keyer or DSK
video layers in front of it.
The Key 1 and Key 2 layers can be used for PiP, Chroma, Linear or Luma Key applications. The KEY video
signal (foreground) is shown in this layer and the FILL video signal is displayed in the background video
layer. If set up incorrectly, these key layers can stop the video behind being displayed.
The Picture in Picture (PiP) feature of the Key 1 & Key 2 layers can be used for displaying a smaller
secondary image in front of the background video layer. This smaller PiP image can be resized, cropped,
repositioned and even keyed by the user to avoid an important part of the background video layer being
covered by it.
The SE-1200 MU has four dedicated keyers, Key1, Key2, DSK1 and DSK2. All four
keyers can be active simultaneously. Key 1 and Key2 can be set as Upstream or
Downstream keyers.
The Layer priority, or order, of Key 1 and Key 2 can also be changed
by the user
using the Priority button in the Transitions Control area. DSK 1 & DSK 2 can only be
used as Downstream keyers. See the diagram above for an example of keyer
layering with the SE-1200 MU.
The Down Stream Key layers (DSK 1 & DSK 2)are placed on top of all the previous layers. These layers are
typically used with Character Generator inputs for displaying titles, graphics, lower thirds, clocks and logos.
Datavideo offer several Character Generator products (additional purchase) such as TC-200, CG-250, CG-

20
350 and CG-500. If set up incorrectly these DSK layers can also stop the video layers behind them being
displayed properly.
Note: Where possible, prepare and position the upper video layers in advance of the live production
starting to avoid appearing on the program output incorrectly. These can be saved as user setups in the
shot box area of the software control interface for quick and easy recall.
Copyright: Most broadcast networks have guidelines and advice on the use of video, images, music, logos
and on screen text so it is best to check beforehand when planning a production. Do not use copyright
protected content until you have the relevant permissions. Information on royalty free video, images and
music is widely available. Please speak with your local dealer or seek professional advice.