Datalogic A30 Installation instructions

A30
Hardware Guide
Publication # 843-0153 (Rev B)

Datalogic Automation, Inc.
6301 West Old Shakopee Rd Suite A
Bloomington MN 55438
USA
A30™ Hardware Guide
Edited: 08/2013
© 2013 Datalogic Automation, Inc. ALL RIGHTS RESERVED. Protected to the fullest extent under
U.S. and international laws. Copying or altering of this document is prohibited without express written
consent from Datalogic Automation, Inc. (DLA)
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries,
including the U.S.A. and the E.U.
A30, Vision Program Manager, Control Panel Manager, and Impact are trademarks of Datalogic
Automation S.r.l. All other brand and product names mentioned herein are for identification purposes only
and may be trademarks or registered trademarks of their respective owners.
DLA makes no representations or warranties for merchantability or fitness for any particular purpose,
regarding DLA’s software or hardware. DLA shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use of this publication or its
contents.
DLA reserves the right to revise this publication from time to time and to make changes in the content
hereof without obligation to notify any person of such revision or changes.
Printed 2 August 2013

i
TABLE OF CONTENTS
REFERENCES ..........................................................................................................iii
Conventions............................................................................................................... iii
Reference Documentation ......................................................................................... iii
Service and Support .................................................................................................. iii
Patents ...................................................................................................................... iii
COMPLIANCE...........................................................................................................iv
EMC Compliance....................................................................................................... iv
Power Supply............................................................................................................. iv
CE Compliance.......................................................................................................... iv
FCC Compliance ....................................................................................................... iv
HANDLING.................................................................................................................v
GENERAL VIEW ......................................................................................................vii
1RAPID CONFIGURATION..........................................................................................1
Step 1 – Assemble the Camera ..................................................................................1
Step 2 – Connect the System .....................................................................................2
Step 3 – Mount and Position the Camera....................................................................4
Step 4 – Focus the Camera ........................................................................................4
Step 5 – Calibrate Image Density................................................................................4
2INTRODUCTION ........................................................................................................5
2.1 Product Description.....................................................................................................5
2.2 Indicators and Keypad Button .....................................................................................6
2.3 Accessories ................................................................................................................7
3INSTALLATION .........................................................................................................8
3.1 Package Contents.......................................................................................................8
3.2 Mechanical Dimensions ..............................................................................................9
3.3 Mounting and Positioning the camera .......................................................................11
4CBX ELECTRICAL CONNECTIONS........................................................................13
4.1 Power Supply............................................................................................................14
4.1.1 Recommended Power Supplies ................................................................................14
4.2 RS232 Serial Interface..............................................................................................15
4.2.1 RS485 Full-Duplex Interface .....................................................................................15
4.3 Auxiliary RS232 Serial Interface................................................................................15
4.4 Inputs........................................................................................................................16
4.5 Outputs.....................................................................................................................21
4.6 External Illuminators .................................................................................................23
5CAMERA ELECTRICAL CONNECTIONS................................................................24
5.1 Power, Serial, and I/O Connector..............................................................................24
5.2 GigaEthernet Connector ...........................................................................................26
5.3 Power Supply............................................................................................................26
5.3.1 Recommended Power Supplies ................................................................................27

TABLE OF CONTENTS
ii
5.4 RS232 Serial Interface..............................................................................................27
5.4.1 RS485 Full-Duplex Interface .....................................................................................28
5.4.2 Auxiliary RS232 Serial Interface................................................................................28
5.5 Ethernet Interface .....................................................................................................28
5.6 Inputs........................................................................................................................30
5.7 Outputs.....................................................................................................................34
6TYPICAL LAYOUTS ................................................................................................37
6.1 Embedded (On-Board) GigaEthernet........................................................................37
6.2 Ethernet Networks ....................................................................................................38
6.2.1 External Trigger Ethernet Host..................................................................................38
6.2.2 No Trigger Ethernet Host ..........................................................................................39
7IMAGE CAPTURE FEATURES................................................................................40
7.1 Maximum Line Speed and Exposure Time Calculations ...........................................40
8SOFTWARE CONFIGURATION ..............................................................................42
8.1 VPM™ System Requirements ..................................................................................42
8.2 Installing Impact Software .........................................................................................42
8.3 Startup......................................................................................................................43
8.3.1 Calibration ................................................................................................................43
8.3.2 Partial Scan ..............................................................................................................44
9MAINTENANCE .......................................................................................................46
9.1 Cleaning ...................................................................................................................46
10 TROUBLESHOOTING .............................................................................................47
10.1 General Guidelines ...................................................................................................47
11 TECHNICAL FEATURES .........................................................................................49
GLOSSARY..............................................................................................................50
INDEX.......................................................................................................................53

iii
REFERENCES
CONVENTIONS
This manual uses the following conventions:
"User" refers to anyone using an A30 camera.
"Camera" refers to an A30 camera.
"You" refers to the System Administrator or Technical Support person using this manual
to install, configure, operate, maintain, or troubleshoot an A30 camera.
REFERENCE DOCUMENTATION
For further details refer to the Impact Reference Guide provided as supplementary
documentation on the installation CD.
SERVICE AND SUPPORT
DLA provides several services as well as technical support through its website. Log on
to www.datalogic.com and click on one of the following links for further information:
•PRODUCTS
Search through the links to arrive at your product page which describes specific Info,
Features, Applications, Models, Accessories, and specific Downloads.
•SUPPORT & SERVICES
- Service Program
- Repair Centers
- On-Line RMA
- Technical Support
- Industrial Automation
- Partner Program
- Downloads
PATENTS
This product is covered by one or more of the following patents:
U.S. patents: 6,512,218 B1; 6,616,039 B1; 6,808,114 B1; 6,997,385 B2; 7,102,116 B2;
7,282,688 B2
European patents: 999,514 B1; 1,014,292 B1; 1,128,315 B1.
Additional patents pending.

iv
COMPLIANCE
For installation, use, and maintenance, it is not necessary to open the camera. Opening
the camera will void the warranty.
Connect Ethernet and dataport connections to a network which has routing only within
the plant or building and no routing outside the plant or building.
EMC COMPLIANCE
In order to meet the EMC requirements:
•connect the camera chassis to the plant earth ground by means of a flat copper braid shorter
than 100 mm;
•for CBX connections, connect the pin "Earth" to a good Earth Ground;
•for direct connections, connect the main interface cable shield to pin K of the 19-pin
connector.
POWER SUPPLY
ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT
This product is intended to be installed by Qualified Personnel only.
This product is intended to be connected to a UL Listed Direct Plug-in Power Unit
marked LPS or “Class 2”, rated 10-30Vdc 1-0.33A.
CE COMPLIANCE
Warning: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
FCC COMPLIANCE
Modifications or changes to this equipment without the expressed written approval of DLA could
void the authority to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference which may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at the user’s own
expense.

v
HANDLING
The A30™ camera is designed to be used in an industrial environment and is built to
withstand vibration and shock when correctly installed However, it is also a precision
product and therefore it must be handled correctly before and during installation to avoid
damage.
•Avoid dropping the camera (exceeding shock limits).
•Do not fine tune the positioning by striking the camera or bracket.

HANDLING
vi
•Do not weld the camera into position. This can cause electrostatic, heat, or imager
damage.
•Do not spray paint near the camera. This can cause imager damage.

vii
GENERAL VIEW
A30™ Camera
1
Power Indicator LED
2
Power, Serial Interface, and I/O Connector
3
MAC Address label
4
Ethernet Connector
5
Ethernet Network Presence LED
6
Indicator Lights (see page 6)
7
Reset and Camera Button Event (see page 6)
1
4
2
5
3
7
6

RAPID CONFIGURATION
1
1
1 RAPID CONFIGURATION
STEP 1 – ASSEMBLE THE CAMERA
The first step to perform is to assemble any accessories that make up the A30™ camera. A lens
must be used. A strobe or other external illuminator may be required.
CAUTION
The camera must be disconnected from the power supply during this
procedure.
1. In a dust-free environment, remove the Camera Lens Cover by unscrewing it.
CAUTION
Do not touch the sensor aperture, lens glass or lens cover glass. These
areas must be kept clean. Avoid any abrasive substances that might
damage these surfaces during cleaning.
2. Remove the sensor protection label (dust cap) by pulling it off of the base.
3. Mount a lens by slowly screwing it onto the base until it arrives at the mechanical stop.
Figure 1 – Assembling the Camera and Lens
4. To keep dust and dirt off of the lens during mounting, temporarily replace the lens cover.
Lens
Lens Cover
Lens Spacer
(optional)
Protective Film
(remove before calibration)
Camera

A30™ HARDWARE GUIDE
2
1
STEP 2 – CONNECT THE SYSTEM
In the typical standalone layout shown in the figure below, an EtherNet host is connected to the
camera. The camera can use an external trigger to signal image acquisition.
The CBX is used to facilitate the connection between the camera and the host interface, external
trigger, and optional input and output devices.
A30™ Standalone Layout to Ethernet Host
•Power Supply Connection
Use the PG-120 power Kit (3 versions for European, UK or US plug) and CAB-PG-0002 +
BA400 connector to connect the PG-120 to the CBX. An alternative power supply to the PG-
120 is the PWR-120.
•CBX Connection
Use CAB-SCSxx between the A30 camera and the CBX for power, external trigger device
(photocell), and additional I/O connections.
Use the CAB-GE0x for the Gigabit Ethernet connection to the host.
NOTE
The A30
does not support sourcing power towards the CBX in order to
power I/O devices. These devices must be powered through the CBX or
from an external source.
CAB-GE0x
CAB-PG-0002
+ BA400
CAB-SCSxx
PG-120
Ext. Trigger
CBX500
I/O
Ethernet Host
(Data collection + A30
configuration)
Camera

RAPID CONFIGURATION
3
1
CBX500 Connectors for A30™
The table below gives the CBX500 terminal block connectors. Use this table when the camera is
connected using the CBX500.
CBX500 Terminal Block Connectors
Input Power
Outputs
Vdc
Power Supply Input Voltage +
+V
Power Source - Outputs
GND
Power Supply Input Voltage -
-V
Power Reference - Outputs
Earth
Protection Earth Ground
O1+
Output 1 +
O1-
Output 1 -
Inputs
O2+
Output 2 +
+V
Power Source – External Trigger
O2-
Output 2 -
I1A
External Trigger A (polarity insensitive)
O3A
Strobe + / Output 3 + (See Note)
I1B
External Trigger B (polarity insensitive)
O3B
Strobe - / Output 3 -
-V
Power Reference – External Trigger
RS232 Interface
+V
Power Source – Inputs
TX
Transmit
I2A
Input 2 A (polarity insensitive)
RX
Receive
I2B
Input 2 B (polarity insensitive)
SGND
Signal Ground
I3A
NOT USED
I4A
NOT USED
I34B
NOT USED
-V
Power Reference – Inputs
Shield
Shield
Network Cable Shield
Note: The strobe signal connection is shared with Output 3. If a non-zero value is defined for the Strobe Pulse
Length value (in VPM – Impact – General), the strobe is active. If the value is zero, Output 3 is active.
CAUTION
Do not connect GND and SGND to different (external) ground references.
GND and SGND are internally connected through filtering circuitry which
can be permanently damaged if subjected to voltage drops over 0.8 Vdc.

A30™ HARDWARE GUIDE
4
1
STEP 3 – MOUNT AND POSITION THE CAMERA
1. Mounting solutions are provided in Chapter 0 of this Hardware Guide.
STEP 4 – FOCUS THE CAMERA
1. Remove the lens cover.
2. Attach the correct accessory lens for your application.
3. Replace the lens cover, if needed.
4. Power the camera on. On the connector side of the camera near the cable, the “POWER
ON” LED (blue) indicates the camera is correctly powered.
5. Start Impact Vision Program Manager (VPM) and use it to connect to the camera.
6. Direct the camera toward a correctly lighted calibration image or other clearly defined object.
7. Select the Settings tab, then click the Camera system object.
8. In the Camera Setup tab, click the Live button.
9. Adjust the lens until the image is clearly in focus in the VPM image window.
STEP 5 – CALIBRATE IMAGE DENSITY
In order to function correctly when inspecting images, the camera needs the image resolution or
PPI (pixels per inch). This calibration procedure is necessary for first time installation, if the lens
type is changed, or if the focal distance is changed.
There are several methods available for calibrating the camera. Refer to the Calibration Panel
section of the Impact Reference Guide (Publication # 843-0093) for complete details.

INTRODUCTION
5
2
2 INTRODUCTION
2.1 PRODUCT DESCRIPTION
The A30 features a 1.1 GHz processor, 256 megabytes of flash memory, integrated Gigabit
Ethernet, and a right-angle mount.
It provides a 640 x 480 pixel image at 60 frames per second using a 1/3” CCD imager.
Excellent Performance
•Adjustable focus through C-Mount lenses
•Frame Rate up to 60 frames/sec
•Partial Scan capabilities for higher frame rate
Flexible Solution
•Modular design
•Adjustable C-Mount lenses
•Complete set of Accessories like external lighting systems, mounting brackets, connection
boxes, cables, and photocells
•Ethernet Connectivity to the host processor PC for parameter configuration, inspection
program development, and data and image transfer.
•General purpose optocoupled I/Os
Industrial Strength
•Industrial compact camera
•Rugged full metal construction
•Sealed circular connectors
•IP65 protection class
•45 °C (113 °F) max operating temperature
•Supply voltage ranges from 10 to 30 Vdc

A30™ HARDWARE GUIDE
6
2
2.2 INDICATORS AND KEYPAD BUTTON
Figure 2 - Indicators
The following LED indicators are located on the camera (Figure 2):
1
POWER
On – camera is connected to power
2
NET
On – Ethernet link is established. Blinking - data transmission
3
BUSY
LED blinks during image and flash memory access
4
OUT1
On – Output 1 is on
5
OUT2
On – Output 2 is on
6
OUT3
On – Output 3 is on
7
ONLINE
On – Loaded tasks will be executed based on their trigger parameters
8
BUTTON
Camera Reset: See Note below
To trigger the Camera Button event, press and release the button (Internal
software event trigger only)
Note: Camera Reset will restore the factory camera settings. This includes deleting all user
settings on the camera and resetting the camera’s IP Address and Mask to the factory default.
To Reset the Camera
1. Turn off power.
2. Press and hold the Camera Reset button.
3. Turn on power.
4. When all the LED indicators turn on and remain lit, release the Camera Reset button.
5. Wait approximately 30 seconds for the camera to restart.
1
2
3
4
5
6
7
8

INTRODUCTION
7
2
2.3 ACCESSORIES
The following is a partial list of optional accessories for the A30 camera.
Accessory
Description
Order No.
Lenses
LNS-1216
16 mm C-Mount Lens 5MP with anti-vibration components
93ACC0041
LNS-1225
25 mm C-Mount Lens 5MP with anti-vibration components
93ACC0034
LNS-1235
35 mm C-Mount Lens 5MP with anti-vibration components
93ACC0035
LNS-1250
50 mm C-Mount Lens 5MP with anti-vibration components
93ACC0036
LPK-45-000
Anti-vibration Kit for C-Mount Lenses
93ACC0051
External Illuminators
LT-300
Ring Lighting System
93A401008
Cables
CAB-PG-0002
Vdc Power PG-120 To BA400 or QL (2M)
93ACC1870
CAB-SCS01
M16-IP67 Cable To CBX (1M)
95A906068
CAB-SCS03
M16-IP67 Cable To CBX (3M)
95A906069
CAB-SCS05
M16-IP67 Cable To CBX (5M)
95A906070
CAB-SCS10
M16-IP67 Cable To CBX (10M)
95A906071
CAB-GE01
M12-IP67 To RJ45 Ethernet Cable (1M)
93A050034
CAB-GE03
M12-IP67 To RJ45 Ethernet Cable (3M)
93A050035
CAB-GE05
M12-IP67 To RJ45 Ethernet Cable (5M)
93A050036
CBL-1480-01
Thin M12/5P Male/Female (1M)
93A050049
CBL-1480-02
Thin M12/5P Male/Female (2M)
93A050050
Connection Boxes
CBX500
Modular Connection Box
93A301068
BA100
DIN Rail Adapters
93ACC1821
BA200
Bosch Adapters
93ACC1822
Various M12 Panel Connectors for CBX Connection Boxes are available
Power Supplies
PG-120-K01
AC/DC Power Supply Kit (EU)
93ACC0046
PG-120-K02
AC/DC Power Supply Kit (UK)
93ACC0047
PG-120-K03
AC/DC Power Supply Kit (US)
93ACC0048
PWR-120
JBOX Power Unit 110/230 Vac 24Vdc
93ACC1530
PWR-240
JBOX Power Unit 110/230 Vac 24Vdc
93ACC1070
PWR-480A
JBOX Power Unit 110/230 Vac 24Vdc
93ACC1850
Sensors
MEP-593
Photocell Kit PNP (PH-1)
93ACC1791
MEP-543
Photocell Kit-NPN
93ACC1728
Brackets
USX-60
Adjustable Bracket A30 Body Mounting Bracket
93ACC1729
BK-4410
Coaxial LT Bracket
93ACC1804
BK-4990
Generic LT Bracket
93ACC1805

A30™ HARDWARE GUIDE
8
3
3 INSTALLATION
3.1 PACKAGE CONTENTS
Verify that the A30™ camera and all the parts supplied with the equipment are present and
intact when opening the packaging. The list of parts includes:
A30 camera with Lens Cover
Software and Documentation CD
QuickStart Guide
Mounting Kit
•Mounting Screws (4 + 3)
•Washers (2)
•Mounting Brackets (2)
Figure 3 – A30 Package Contents

INSTALLATION
9
3
3.2 MECHANICAL DIMENSIONS
The A30 can be installed to operate in different positions using the body mounting bracket
shown in Figure 5. The twelve screw holes (M4) on the body of the camera can be used for
custom mounting solutions.
The diagram below gives the overall dimensions of the camera.
Refer to section 3.3 for various mounting solutions and correct positioning.
Figure 4 – A30 Overall Dimensions

A30™ HARDWARE GUIDE
10
3
Figure 5 – Mounting Bracket Overall Dimensions
mm
[in]