Datalogic EOX 30W User manual

GUIDA PER L’INSTALLAZIONE RAPIDA
QUICK INSTALLATION GUIDE
EOX 30W
Rev. A
DATALOGICAUTOMATION - LASER MARKING
www.automation.datalogic.com
Laser Marking operation officies
Donnas
Reg. Gurey, via Le Gorrey, 10
11020 Donnas (AO) - ITALY
Tel. [phone]
Fax [phone]
Sesto Calende
Via dell’Industria, 20
21018 Sesto Calende (VA) - ITALY
Tel. [phone]
Fax [phone]
Headquarters
Via Lavino, 265
40050 Monte San Pietro
Bologna - Italy
Tel. [phone]
Fax [phone]
Purchasing Dept. Fax [phone]
[email protected]
851001210

2. Fissare Rack di controllo.
2. Secure control rack. 3. Rimuovere la cover. 3. Remove rack cover. 4. Agganciare il passacavo al rack. 4. Hook the main cable. 5. Collegare cavo rack-risonatore (J7). 5. Connect rack-resonator cable (J7). 6. Cablare morsetti di alimentazione (J18). 6. Wire power supply terminal blocks (J18).
9. Collegare l’alimentazione 30Vdc.
9. Plug 30Vdc power supply.
NOTA:
Per una corretta installazione del dispositivo , consultare il Manuale d’UsoEox
NOTE:
For a right installation of devices, please consult User’s ManualEox
1. Fissare risonatore.
1. Fixing resonator.
ATTENZIONE:
Il dispositivo è un laser di classe 4. Per il corretto utilizzo in sicurezza deve essere portato a classe 1.Eox
ATTENTION:
The device is a class 4 laser. For proper use in full safety, it must be modified to class 1.Eox
7. Connettere cavo iMark (J2001).
7. Plug iMark connector (J2001). 8. Collegare cavo di terra. 8. Wire earth cable. 10. Chiudere la cover. 10. Close rack cover.
11. Collegare la Command Box.
11. Wire the Command Box. 12. Collegare gli assi. 12. Wire the axes. 13. Collegare il connettore di Interlock. 13. Wire the Interlock connector. 14. Collegare il cavo di alimentazione. 14. Wire power supply cable.
15. Collegare il mouse.
15. Plug the mouse. 17. Collegare il monitor.
17. Plug the monitor.
16. Collegare la tastiera.
16. Plug the keyboard. 18. Accendere il dispositivo. 18. Power ON the device.
2
1
3
4
EXTERNAL
INTERLOCK
6
11
6
13
STOP
MARKING
START
MARKING
5
10
CBOX CONNECTOR
PRESENCE
2K2
2K2
2K2
17
9
23
1
2
REMOTE
INTERLOCK
7
8
EXTERNAL ENABLE
4
12
EXTERNAL KEY
INTERLOCK
CONNECTOR
PRESENCE
2K2 20
SYSTEM ALARM
LASER BUSY / EMISSION
LASER ENGINE READY
END MARKING
2K2 22
2K2 3
GOOD/BAD MARKING
POWER
(10÷30Vdc)
EMERGENCY STOP
SWITCH
L
N
MAIN POWER SUPPLY
CONNECTOR
I/O INTERFACE
CONNECTOR
SHUTTER OPENED
1
POWER LINE
INPUT
16
1
15
14
CODE 1
CODE 2
CODE 3
14
13 25
ESEMPIO DI CONNESSIONE.
CONNECTION .EXAMPLE
+5V
GND
+12V
GND
+5V
GND GND
+12V