manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Datalogic
  6. •
  7. PDA
  8. •
  9. Datalogic Memor 10 Owner's manual

Datalogic Memor 10 Owner's manual

Datalogic S.r.l.
Via San Vitalino 13
40012 Calderara di Reno (BO)
Italy
Tel. +39 051 3147011
Fax +39 051 3147205
©2016-2017 Datalogic S.p.A. and/or its affiliates
All rights reserved. Without limiting the rights under copyright, no part of this documentation may be reproduced,
stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any purpose, without
the express written permission of Datalogic S.p.A. and/or its affiliates. Owners of Datalogic products are hereby granted
a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal
business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in
this documentation and shall ensure that all notices appear on any reproductions of the documentation. Should future
revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative.
Electronic versions may either be downloadable from the Datalogic website (www.datalogic.com) or provided on
appropriate media. If you visit our website and would like to make comments or suggestions about this or other
Datalogic publications, please let us know via the "Contact Datalogic" page.
Safety & Regulatory Addendum
(Rev. A) October 2017
General Safety Rules
Power Supply
The device is intended to be supplied by a self-contained rechargeable Lithium Ion battery pack
(UL listed LPS/SELV power source) and/or by UL Listed/CSA Certified Power Unit LPS/SELV
power source which supplies power directly to the unit via the micro USB connector of the cable.
The device could be also used with Certified Accessories (Dock/Cradle) which supply Wireless
power. The Dock/Cradle accessories are intended to be supplied by a UL Listed/CSA Certified
Power Unit LPS/SELV rating 12V, min 5A power source which supplies power via the power
connector of the cable.
Any changes or modifications to equipment, not expressly approved by Datalogic could void the
user's authority to operate the equipment.
Battery Information
By default, the main battery pack is disconnected at the factory to avoid damage due to
excessive draining.
Rechargeable battery pack is less than half of full charge when delivered. Charge the battery
pack as indicated in the Quick Start Guide or in the User Manual, before using the MEMOR 10
terminal.
The battery pack autonomy varies according to many factors, such as the frequency of barcode
scanning, RF usage, battery life, storage, environmental conditions, etc.
Close to the limits of the working temperature, some battery performance degradation may
occur.
The MEMOR 10 should be charged at an ambient temperature between 0 - 35º C (32 to 122ºF) to
achieve the maximum charging rate.
Never charge the device battery in a closed space where excessive heat can build up.
As a safety precaution, the battery may stop charging to avoid overheating.
The MEMOR 10 gets warm during charging; this is normal and does not mean a malfunction.
Even if the storage temperature range is wider, it is recommended to store the terminal and the
batteries at environmental temperature, in order to achieve the longest battery life.
NOTE
Read carefully the MEMOR 10 user manual (available at
www.datalogic.com
) before
performing any type of connection to the MEMOR 10.
The user is responsible for any damage caused by incorrect use of the equipment or by
inobservance of the indication supplied in the user manual.
CAUTION
• Before using the devices and the battery packs, read this Addendum carefully.
•Use only the components and accessories supplied by the manufacturer for the
specific
MEMOR 10
being used.
• Do not attempt to disassemble the
MEMOR 10
device, as it does not contain
parts that can be repaired by the user. Any tampering will invalidate the
warranty.
• When replacing the battery pack or at the end of the operative life of the
•
MEMOR 10
device, disposal must be performed in compliance with the laws
in force in your jurisdiction.
• Do not submerge the
MEMOR 10
in liquid products.
• For further information or support, refer to the Datalogic web site:
www.datalogic.com.
CAUTION
Do not apply any sticker to the MEMOR 10.
CAUTION
Do not incinerate, disassemble, short terminals, or expose to high temperature. Risk of fire and
explosion. Use specified charger only. Risk of explosion if the battery is replaced by an incorrect
type. Dispose of batteries as required by local authorities.
CAUTION
Avoid storing batteries for long periods in a state of full charge or very low charge.
We recommend charging the battery pack every two to three months to keep its charge at a
moderate level to maximize battery life.
Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and
ensures maximum performance.
WARNING
Use only Datalogic approved batteries and accessories for battery charging.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Il y a risque d’explosion si la batterie est remplacée par une batterie de type incorrect.
Mettre au rebut les batteris usagées confor mément aux instructions.
CAUTION
Do not put any foreign object such as, but not limited to, coins, paper clips, stickers inside the
slot of any of the docks (see the examples below).
Battery Safety Guidelines
Wireless and Radio Frequencies Warnings
WARNING
Installing, charging and/or any other action should be done by authorized personnel and
following this manual.
The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to
abusive conditions.
If the battery pack is replaced with an improper type, there is risk of explosion.
Do not place the battery pack in or near a fire or other heat source; do not place the battery
pack in direct sunlight, or use or store the battery pack inside unventilated areas in hot
weather; do not place the battery pack in microwave ovens, in clothes dryers, in high pressure
containers, on induction cook surfaces or similar devices. Doing so may cause the battery pack
to generate heat, explode or ignite. Using the battery pack in this manner may also result in a
loss of performance and a shortened life expectancy.
To power the cradle, use only a Datalogic approved power supply. The use of an alternative
power supply will void the product warranty, may cause product damage and may cause heat,
an explosion, or fire.
The area in which the units are charged should be clear of debris and combustible materials or
chemicals.
Do not use the battery pack of this terminal to power devices other than this device.
Immediately discontinue use of the battery pack if, while using, charging or storing the battery
pack, the battery pack emits an unusual smell, feels hot, changes colour or shape, or appears
abnormal in any other way.
Do not short-circuit the battery pack contacts connecting the positive terminal and negative
terminal. This might happen, for example, when you carry a spare battery pack in your pocket
or purse; accidental short–circuiting can occur whenametallic object such as a coin, clip, or
pen causes direct connection of the contacts of the battery pack (these look like metal strips
on the battery pack). Short–circuiting the terminals may damage the battery pack or the
connecting object.
Do not apply voltages to the battery pack contacts.
Do not pierce the battery pack with nails, strike it with a hammer, step on it or otherwise
subject it to strong impacts, pressures, or shocks.
Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack
contains safety and protection devices, which, if damaged, may cause the battery pack to
generate heat, explode or ignite.
In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the
contact occurs, immediately wash the affected area with water and consult a doctor.
Do not solder directly onto the battery pack.
Do not expose the battery pack to liquids.
Avoid any knocks or excessive vibrations. If the device or the battery is dropped, especially on
a hard surface, you should take it to the nearest Authorised Repair Centre for inspection
before continuing to use it.
If your device stops working for any reason, do not use its battery on other electronic devices
without a prior check and approval by an Authorised Repair Centre.
Do not remove or damage the battery pack’s label.
Do not use the battery pack if it is damaged in any part.
Battery pack usage by children should be supervised.
Collect and recycle waste batteries separately from the device in compliance with European
Directive 2006/66/EC, 2011/65, 2002/96/EC and subsequent modifications, with US and
China regulatory laws and regulations about the environment.
WARNING
Use only the supplied or an approved replacement antenna. Unauthorized antennas,
modifications or attachments could damage the product and may violate laws and
regulations.
Most modern electronic equipment is shielded from RF signals. However, certain electronic
equipment may not be shielded against the RF signals generated by MEMOR 10.
Datalogic recommends persons with pacemakers or other medical devices to follow the same
recommendations provided by Health Industry Manufacturers Associations for mobile
phones.
Persons with pacemakers:
• Should ALWAYS keep this device more than twenty five (25) cm from their
pacemaker and/or any other medical device;
• Should not carry this device in a breast pocket;
• Should keep the device at the opposite side of the pacemaker and/or any other
medical device;
• Should turn this device OFF or move it immediately AWAY if there is any
reason to suspect that interference is taking place.
• Should ALWAYS read pacemaker or any other medical device guides or should
consult the manufacturer of the medical device to determine if it is adequately
shielded from external RF energy.
In case of doubt concerning the use of wireless devices with an implanted medical device,
contact your doctor.
Turn this device OFF in health care facilities when any regulations posted in these areas
instruct you to do so. Hospitals or health care facilities may use equipment that could be
sensitive to external RF energy.
RF signals may affect improperly installed or inadequately shielded electronic systems in
motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You
should also consult the manufacturer of any equipment that has been added to your vehicle.
An air bag inflates with great force. DO NOT place objects, including either installed or portable
wireless equipment, in the area over the air bag or in the air bag deployment area. If a
vehicle’s wireless equipment is improperly installed and the air bag inflates, serious injury
could result.
Turn off the device when in any area with a potentially explosive atmosphere. Observe
restrictions and follow closely any laws, regulations, warnings and best practices on the use
of radio equipment near fuel storage areas or fuel distribution areas, chemical plants or where
any operation involves use of explosive materials.
Do not store or carry flammable liquids, explosive gases or materials with the device or its
parts or accessories.
Areas with a potentially explosive atmosphere are often, but not always, clearly marked or
shown.
Sparks in such areas could cause an explosion or fire, resulting in injury or even death.
This document is an addendum to the Quick
Start Guide (QSG) for this product. See the QSG
for additional product information.
www.datalogic.com
852001650 (Rev. A) July 2019
Rugged Mobile Computer
with 1D/2D Imager
FCC compliance
NOTICE:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC ID: U4GDL35US
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however,
Datalogic reserves the right to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and
the E.U. Memor is a trademark of Datalogic S.p.A. and/or its affiliates
All other trademarks and brands are property of their respective owners. Google, Google Play and other marks are
trademarks of Google LLC. Patents
See www.patents.datalogic.com for patent list.
This product is covered by one or more of the following patents:
Design patents: EP004675072, EP004803013, EP005513751
Utility patents: EP0999514B1, EP0996284B1, EP1128315B1, , EP1396811B1, EP1413971B1, , EP1828957B1, EP2517148B1
US6808114, US6997385, US7053954, US7234641, US7387246, US8888003, US8915443, US9798948, ZL200980163411.X
NOTE:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC-
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particul-
ar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply With RF exposure requirements, a minimum separation distance
of 1.0cm must be maintained between the user’s body and the handset, including the antenna.Third-party belt-clips, holsters, and
similar including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any
metalliccom-ponents. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements
and should be avoided.
Specific Absorption Rate (SAR) information:
This wireless phone meets the government's requirements for exposure to radio waves.The guidelines are based on standards that
were developed by independent scientific organizations through periodic and thorough evaluation of scientificstudies. The standards
include a substantial safety margin designed to assure the safety of all persons regardless ofage or health.
FCC RF Exposure Information and Statement:
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: U4GDL35US has also been tested against this
SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.801W/kg and when
properly worn on the body is 1. andashotspotis .This device was tested for typical body-worn operations with
the back of the handset kept 1cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that
maintain a 1cm separation distance between the user's body and the back of the handset. The use of belt clips, holst-ers and similar
accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements
may not comply with FCC RF exposure requirements, and should be avoided.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-
channel mobile satellite systems;
ISED Compliance
NOTICE:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired operation.
Cleaning The Device
LED Class
CAUTION
the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-
channel mobile satellite systems;
high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350MHz and 5650-5850 MHz and tha t
these radars could cause interference and/or damage to LE-LAN devices. 801
1.
ssttaatteemmeenntteeexxppoossuurrenrraaddiiaattiioonDISSEEDI
This device is compliant with SAR for general population/uncontrolled exposure limits in RSS-102 and has been tested in accordance
with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and
operated with a minimum distance of 0.39 in(10mm) between the radiator and you body. This device and its antennas must not be
co-located or operated in conjunction with and other antenna or transmitter.
Cet appareil est conforme aux limites d'exposition DAS incontrôlée pour la population générale de la norme CNR-102
Innovation. Scinces et Développement économique Canada et a été testé en conformité avec les méthodes de mesure de procédures
spécifiées dans IEEE 1528 et IEC 62209. Cet appareil doit être installé et utilisé avec une distance minimale de
10mm entre I'émetteur et votre corps. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en
conjonction avec tout autre antenne ou transmetteur.
©2016-2017 Datalogic S.p.A. and/or its affiliates. All
rights reserved. Datalogic and the Datalogic logo are
registered trademarks of Datalogic S.p.A. in many
countries, including the U.S. and the E.U.
Periodically clean the MEMOR 10 using a soft cloth slightly dampened with only water or
Isopropyl Alcohol (70%). Do not use any other cleaning agents (e.g. different alcohol, abrasive
or corrosive products, solvents) or abrasive pads to clean the device.
Do not spray or pour liquids directly onto the device.
The device is IP65 waterproof.
LED illuminator integrated in the imager engine is classified as “EXEMPT RISK GROUP”
according to IEC62471.
Memor™ 10
El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los ojos humanos a consecuencia de una exposición de
corta duración. Eviten de mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad intensa, por ejempl o el sol.
Además, eviten de dirigir el rayo láser hacia los ojos de un observador, también a través de superficies reflectantes como los espejos.
.
ATENCIÓN
No intente abrir o de ninguna manera dar servicio a ninguno de los componentes del receptáculo óptico. Abrir o dar servicio a las piezas del
receptáculo óptico por parte del personal no autorizado podría ser una violación a los reglamentos de seguridad. El sistema óptico se
puede reparar en la fábrica solamente.
La utilización de procedimientos o regulaciones diferentes de aquellas describidas en la documentación puede causar una exposición
peligrosa a la luz láser visible.
El uso de sistemas ópticos con el escáner aumentará el riesgo de daños oculares. Los instrumentos ópticos incluyen binoculares,
microscopios, lentes y lupas.
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les autorités internationales et se réfèrent à une correcte
utilisation du terminal.
NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de fabrication: CDRH 21 CFR 1040 et EN 60825-1.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entretien.
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été constaté à la suite d’une exposition au rayon laser.
Eviter de regarder fixement le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter aussi de diriger le rayon
vers les yeux d’un observateur, même à travers des surfaces réfléchissantes (miroirs, par exemple).
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las disposiciones de las autoridades internacionales y se refieren
al uso correcto del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de seguridad láser a la fecha de producción: CDRH 21 CFR 1040 y
1.
No es necesario abrir el aparato para la instalación, la utilización o la manutención.
ATTENTION
LNe pas essayer d’ouvrir ou de réparer les composants de la cavité optique. L’ouverture de la cavité optique ou la réparation de ses
composants par une personne non qualifiée peut entraîner le nonrespect des règles de sécurité relatives au laser. Le système optique ne
peut être réparé qu’en usine.
L'utilisation de procédures ou réglages différents de ceux donnés ici peut entraîner une dangereuse exposition à lumière laser visible.
L’utilisation d’instruments optiques avec le scanneur augmente le danger pour les yeux. Les instruments optiques comprennent les
jumelles, les microscopes, les lunettes et les verres grossissants.
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni riportati dall’occhio umano in seguito ad una
esposizione di breve durata, evitare di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente di luminosità intensa, ad
esempio il sole. Evitare inoltre di dirigere il raggio laser negli occhi di un osservatore, anche attraverso superfici riflette nti come gli
specchi.
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die von internationalen Behörden auferlegt wurden,
und sie beziehen sich auf den korrekten Gebrauch vom Terminal.
NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und CDRH 21 CFR 1040 Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations- und Wartungs-Arbeiten zu öffnen.
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von kurzen Einstrahlungen bekannt sind, sollten Sie es
vermeiden für längere Zeit in den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie
es, den Laserstrahl weder gegen die Augen eines Beobachters, noch gegen reflektierende Oberflächen zu richten.
ATTENZIONE
Non tentare di accedere allo scomparto contenete i componenti ottici o di farne la manutenzione.
L’apertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di personale non autorizzato, potrebbe violare le norme
della sicurezza. Il sistema ottico può essere riparato solamente alla fabbrica.
L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione può provocare un'esposizione pericolosa a luce
laser visibile.
L’uso di strumenti ottici assieme allo scanner può aumentare il pericolo di danno agli occhi. Tali strumenti ottici includono cannocchiali,
microscopi, occhiali e lenti di ingrandimento.
ACHTUNG
Unter keinen Umständen darf versucht werden, die Komponenten im Optikhohlraum zu öffnen oder auf irgendwelche andere Weise zu
warten. Das Öffnen bzw. Warten der Komponenten im Optikhohlraum durch unbefugtes Personal verstößt gegen die Laser-
Sicherheitsbestimmungen. Das Optiksystem darf nur werkseitig repariert werden.
Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht in dieser Betriebsanleitung beschrieben werden, können ein gefährliches
Laserlicht verursachen.
Die Verwendung von Optiksystemen mit diesem Scanner erhöht die Gefahr einer Augenbeschädigung. Zu optischen Instrumenten gehören
unter anderem Ferngläser, Mikroskope, Brillen und Vergrößerungsgläser.
ENGLISH
The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of
your device.
STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN 60825-1 at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.
The product utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known biological
damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid that the laser beam hits the
eye of an observer, even through reflective surfaces such as mirrors, etc.
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e si riferiscono all’uso corretto del terminale.
NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produzione: CDRH 21 CFR 1040 e EN
60825-1.
Non si rende mai necessario aprire l’apparecchio per motivi di installazione, utilizzo o manutenzione.
WARNING
Do not attempt to open or otherwise service any components in the optics cavity. Opening or servicing any part of the optics cavity by
unauthorized personnel may violate laser safety regulations. The optics system is a factory only repair item.
Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazardous
visible laser light.
Use of optical systems with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes, eye glasses and
magnifying glasses.
LOÑAPSESIAÇNARFHCSTUEDONAILATI
LA LUCE LASER È VISIBILE ALL'OCCHIO
UMANO E VIENE EMESSA DALLA
FINESTRA INDICATA NELLA FIGURA.
DIE LASER-STRAHLUNG IST FÜR DAS
MENSCHLICHE AUGE SICHTBAR UND
WIRD AM STRAHLAUS TRITTSFENSTER
AUSGESENDET (SIEHE BILD).
LE RAYON LASER EST VISIBLE À L'OEIL
NU ET IL EST ÉMIS PAR LA FENÊTRE
DÉSIGNÉE SUR L'ILLUSTRATION DANS
LA FIGURE.
A LUZ LÁSER ES VISIBLE AL OJO
HUMANO Y ES EMITIDA POR LA
VENTANA INDICADA EN LA FIGURA.
LUCE LASER NON FISSARE IL FASCIO
APPARECCHIO LASER DI CLASSE 2
MASSIMA POTENZA D'USCITA: 1 mW
LUNGHEZZA D'ONDA EMESSA: 630~680
nm
CONFORME A EN 60825-1:2014.
LASERSTRAHLUNG NICHT IN DEN
STRAHL BLICKEN PRODUKT DER
LASERKLASSE 2 MAXIMALE
AUSGANGSLEISTUNG: 1 mW
WELLENLÄGE: 630~680 nm
ENTSPR.und
RAYON LASER EVITER DE REGARDER LE
RAYON APPAREIL LASER DE CLASSE 2
PUISSANCE DE SORTIE: 1 mW
LONGUEUR D'ONDE EMISE: 630~680 nm
CONFORME A
RAYO LÁSER NO MIRAR FIJO EL RAYO
APARATO LÁSER DE CLASE 2 MÁXIMA
POTENCIA DE SALIDA: 1 mW
LONGITUD DE ONDA EMITIDA: 630~680
nm
CONFORME A y EN 60825-1:2014.
The following information applies to Laser Aiming System, used on
The laser light is visible to the human eye and is emitted from the window indicated in the figure below
NOTE
The artwork below may be only a draft. Please refer to the label attached to the product for information about
certification ma
Laser Warning Label
Scan Window
Laser Safety
MEMOR 10.
IEC
/
EN 60825-1:2014.
IEC
/
EN 60825-1:2014.
IEC
/
IEC
IEC
/
IEC
/
IEC
/
IEC
/
60825- EN
IEC
/
Canadian Statement
Ne pas regarder le faisceu.
Attention classe 2 lumière laser en cas d’ouverture eviter l’esposition - lumière est émise de
la ouverture.
Ce produit est conform au sous-chapitre J de CFR 21.
Pour le modèle avec TYPE qui contient deux lettres “FD”.
Rayonnement laser – ne pas regarder dans le faisceu – ne par regarder avec strumentation
optique - appareil à laser de classe 2 – emission maximale de 1mw – longueur d’onde emise
630 - 680nm – selon IEC/EN 60825-1:2014.
Anatel Statements
Este produto está homologado pela Anatel, de acordo com os procedimentos regulamentados pela Resolução nº 242/2000 e atende aos
requisitos técnicos aplicados, incluindo os limites de exposição da Taxa de Absorção Específica referente a campos elétricos, magnéticos e
eletromagnéticos de radiofrequência, de acordo com as Resoluções nº 700/218.
Máximo valor de SAR encontrado: GPRS/850 MHz (1,74 W/Kg)
Resolução 680/Ato 14448-ANATEL
“Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar
interferência em sistemas devidamente autorizados.”
A distância mínima de separação entre a parte traseira do celular com o corpo é de 0 , 5 cm.
Para consultas à Anatel utilizar o site www.anatel.gov.br
Complies with 21 CFR 1040.10 and
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAX OUTPUT RADIATION 1mW EMITTED
1040.11 except for conformance
with IEC 60825-1 Ed.3.,as described in
Laser Notice No.56,dated May 8,2019
WAVE LENGTH 630-680nm 5ms PULSE
IEC/EN 60825-1:2014
04924-19-04858

Other manuals for Memor 10

3

Other Datalogic PDA manuals

Datalogic PowerScan PM8300 User manual

Datalogic

Datalogic PowerScan PM8300 User manual

Datalogic MEMOR 20 User manual

Datalogic

Datalogic MEMOR 20 User manual

Datalogic Kyman\ User manual

Datalogic

Datalogic Kyman\ User manual

Datalogic Pegaso Falcon User manual

Datalogic

Datalogic Pegaso Falcon User manual

Datalogic Falcon 5500 Installation and operating instructions

Datalogic

Datalogic Falcon 5500 Installation and operating instructions

Datalogic Skorpio X3 User manual

Datalogic

Datalogic Skorpio X3 User manual

Datalogic Memor 11 User manual

Datalogic

Datalogic Memor 11 User manual

Datalogic Falcon X4 User manual

Datalogic

Datalogic Falcon X4 User manual

Datalogic Memor 1 User manual

Datalogic

Datalogic Memor 1 User manual

Datalogic Kyman\ User manual

Datalogic

Datalogic Kyman\ User manual

Datalogic JoYa A6 Touch User manual

Datalogic

Datalogic JoYa A6 Touch User manual

Datalogic Pegaso User manual

Datalogic

Datalogic Pegaso User manual

Datalogic Skorpio X4 User manual

Datalogic

Datalogic Skorpio X4 User manual

Datalogic Industrial PDA User manual

Datalogic

Datalogic Industrial PDA User manual

Datalogic WEC7 OS User manual

Datalogic

Datalogic WEC7 OS User manual

Datalogic Memor X3 User manual

Datalogic

Datalogic Memor X3 User manual

Datalogic Lynx D User manual

Datalogic

Datalogic Lynx D User manual

Datalogic Memor 11 User manual

Datalogic

Datalogic Memor 11 User manual

Datalogic Jet User manual

Datalogic

Datalogic Jet User manual

Datalogic DL-Axist User manual

Datalogic

Datalogic DL-Axist User manual

Datalogic ELF User manual

Datalogic

Datalogic ELF User manual

Datalogic Memor X3 User manual

Datalogic

Datalogic Memor X3 User manual

Datalogic Lynx D User manual

Datalogic

Datalogic Lynx D User manual

Datalogic Memor X3 Healthcare User manual

Datalogic

Datalogic Memor X3 Healthcare User manual

Popular PDA manuals by other brands

Symbol PDT 6100 Series Product reference guide

Symbol

Symbol PDT 6100 Series Product reference guide

Newton Newton Press user guide

Newton

Newton Newton Press user guide

Dell Axim X30 quick start

Dell

Dell Axim X30 quick start

Psion 7515 user manual

Psion

Psion 7515 user manual

palmOne Tungsten T5 user guide

palmOne

palmOne Tungsten T5 user guide

Franklin Crossword Puzzle Solver CWM-108 user guide

Franklin

Franklin Crossword Puzzle Solver CWM-108 user guide

SPOT GEN4 quick start guide

SPOT

SPOT GEN4 quick start guide

Unitech PA600 user manual

Unitech

Unitech PA600 user manual

palmOne Zire 31 user guide

palmOne

palmOne Zire 31 user guide

CipherLab Series 8 Reference manual

CipherLab

CipherLab Series 8 Reference manual

HandHeld NAUTIZ X5 quick start guide

HandHeld

HandHeld NAUTIZ X5 quick start guide

Hitachi HPW-200EC Hardware user's guide

Hitachi

Hitachi HPW-200EC Hardware user's guide

Honeywell ScanPal EDA52 user guide

Honeywell

Honeywell ScanPal EDA52 user guide

Mobile Crossing WayPoint 100 user guide

Mobile Crossing

Mobile Crossing WayPoint 100 user guide

Franklin BOOKMAN ADV-2002 user guide

Franklin

Franklin BOOKMAN ADV-2002 user guide

Honeywell CT50L0N quick start guide

Honeywell

Honeywell CT50L0N quick start guide

Franklin BOOKMAN STK-2032 user guide

Franklin

Franklin BOOKMAN STK-2032 user guide

Unitech EA320 user manual

Unitech

Unitech EA320 user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.