Dataprobe iBoot-PDU8-C20 User manual

iBootPDU Quick Start © 2017 Dataprobe Inc. v170731e
What’s Included
iBoot-PDU Unit
Rack Mounting Ears
Network Cable
Quick Start Guide
USB Cable
Available Online at dataprobe.com/support-documents/iboot-pdu/
Complete Product Manual
Device Management Utility
Latest iBoot-PDU Firmware
Software Developer Tools
SNMP MIB
Orientation
Front Panels 8 Outlets 4 Outlets
Rear Panel –NEMA Versions
Rear Panel –IEC Versions
Quick Start Defaults
IP address DHCP Assigned or 192.168.1.254
User Credentials Username: admin
Password: admin
Quick Start Guide

iBootPDU Quick Start © 2017 Dataprobe Inc. v170731e
Changing the IP Address
1. Device Management Utility Obtain the Device
Management Utility (DMU) from Dataprobe’s website
at dataprobe.com/support-documents/iboot-pdu/
a. Open the DMU on a PC on the same physical network as
the iBoot-PDU and select Device > Discover to display
the current IP Address of the iBoot-PDU.
b. Select Set > Network Settings to change the network
settings. The IP settings can only be set within the first
two minutes of powering up the iBoot-PDU. The DMU
will only work with iBoots on the same physical subnets
as the PC
Complete instructions for the DMU are provided with the
download, and in the full iBoot-PDU Manual.
2. Web Page Setup From the home page (Dashboard),
click on Device -> IP Address. Set the IP Mode to Static.
Enter the new IP Address, Subnet Mask, Gateway and DNS,
then click Save. Click Save to store the settings as entered.
Once saved, they are held as Pending. To complete the
process, reboot the iBoot-PDU. When the iBoot-PDU is ready
for reboot, a notification will appear at the top left of the
dashboard. Click on notifications, then reboot.
Web Browser Control
The iBoot-PDU web interface provides the easiest means
of operating the outlets and monitoring the current status of
the units. One or more outlets can be simultaneously
controlled with a few mouse clicks.
To Control any of the outlets, From the Dashboard screen,
highlight the outlet(s) to be controlled with a mouse click,
then click on the desired Action Buttons ON –OFF -
CYCLE
When Cycle is selected, the outlet(s) will cycle for the
amount of time set (default 10 Seconds). When more than
one outlet is controlled to turn on, there will be a delay
between outlets turning on, as set by the delay setting
(default 1 Second).
To get all the benefits of your iBoot, register it: dataprobe.com/product-registration-form
Notification of Updates
Exclusive Offers
Expedited Warranty Service
Advanced End-of-Life Notification

Important Safety Instructions
When using this product, basic safety precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product in an outdoor environment or near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product
may fall, causing serious damage to the product.
6. Slots and openings in this product and the back or bottom are provided for
ventilation to protect it from overheating; these openings must not be
blocked or covered. The openings should never be blocked by placing the
product on the bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless proper ventilation is
provided.
7. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company.
8. This product is equipped with a three wire grounding type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding type
power outlet. This is a safety feature. If you are unable to insert the plug
into the outlet, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the grounding type plug. Do not use a 3-
to-2 prong adapter at the receptacle; use of this type adapter may result in
risk of electrical shock and/or damage to this product.
9. Do not allow anything to rest on the power cord. Do not locate this product
where the cord will be abused by persons walking on it.
10. Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
11. Never push objects of any kind into this product through slots as they may
touch dangerous voltage points or short out parts that could result in a risk
of fire or electrical shock. Never spill liquid of any kind on the product.
12. To reduce the risk of electrical shock, do not disassemble this product, but
take it to a qualified serviceman when some service or repair work is
required. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect re-assembly can cause electric shock
when the appliance is subsequently used.
13. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the power supply cord or plug is damaged or frayed.
b) If liquid has been spilled into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions because improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the product to normal operation.
e) If the product has been dropped or has been damaged.
f) If the product exhibits a distinct change in performance.
14. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
15. Do not use the telephone to report a gas leak in the vicinity of the leak.
16. Do not exceed the maximum output rating of the auxiliary power receptacle.
This unit is intended for connection to Information Technology Equipment (ITE) only
Technical Support, Returns and Warranty
Dataprobe Technical Support is available 8:30AM to 5:30PM ET to assist you in the installation and operation of this product. To
obtain Technical Support call 201- 934-5111, or Email us at [email protected]. Please have the following information
available when you call:
•Model of Product
•Lot and Version Numbers
•Data of Purchase
•Name of Seller (if other than Dataprobe)
If you purchased this product through an Authorized Dataprobe Reseller, you should contact them first, as they may have information
about the application that can more quickly answer your questions.
3 Year WARRANTY
Download complete manual or visit info.dataprobe.com/support/dataprobe_warranty.pdf