David White LL360P User manual

www.davidwhite.us.com
LL360P
LL360P Laser Owner’s Guide
FOR CUSTOMER SERVICE, PARTS AND REPAIR CALL
[phone]
IMPORTANT: IMPORTANT: IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar

-2-
With David White
your sights are set on
precision and accuracy.
Congratulations! You’ve purchased a David White builder/contractor
instrument, known throughout the world for precision and accuracy.
The purpose of this user’s guide is to acquaint you with the instrument, its
components, safety, proper care and handling.
Our levels, level-transits and transits are constructed to withstand
extremely rugged field use. Like all precision instruments, however, they
should be treated with reasonable care to prolong life and accuracy.
All instruments are adjusted when they are shipped from the factory. It
is the customer’s responsibility to check and to ensure instruments are
adjusted prior to using.
David White is not responsible for errors caused by instruments that are
out of adjustment.
Contact your distributor, dealer or David White for information on the
nearest facility to check if your instrument is properly adjusted.
All specifications are subject to change without notice.

-3-
1
2
4
3
56
LL360P
b
c
d
e
a

-4-
GENERAL SAFETY RULES
!WARNING Read all instructions. Failure to follow all instructions listed
below may result in hazardous radiation exposure, electric
shock, fire and/or serious injury.
If glass light house breaks when dropped, contact customer service
immediately. Broken glass can cause laceration hazard and unit to
lose its IP rating.
IEC 60825-1:2007-03
<
1 mW, 635 nm
DO NOT direct the laser beam at persons or animals and do not
stare into the laser beam yourself. This tool produces laser class 2
laser radiation and complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to Laser Notice No. 50, dated June
24, 2007. This can lead to persons being blinded.
DO NOT remove or deface any warning or caution labels.
Removing labels increases the risk of exposure to laser radiation.
Use of controls or adjustments or performance of procedures other than those
specified in this manual, may result in hazardous radiation exposure.
ALWAYS make sure that any bystanders in the vicinity of use are made aware
of the dangers of looking directly into the laser tool.
DO NOT place the laser tool in a position that may cause anyone to stare into
the laser beam intentionally or unintentionally. Serious eye injury could result.
ALWAYS position the laser tool securely. Damage to the laser tool and/or
serious injury to the user could result if the laser tool falls.
ALWAYS use only the accessories that are recommended by the manufacturer
of your laser tool. Use of accessories that have been designed for use with
other laser tools could result in serious injury or unsatisfactory performance.
DO NOT use this laser tool for any purpose other than those outlined in this
manual. This could result in serious injury or unsatisfactory performance.
DO NOT leave the laser tool “ON” unattended in any operating mode.
DO NOT disassemble the laser tool. There are no user serviceable parts inside.
Do not modify the product in any way. Modifying the laser tool may result in
hazardous laser radiation exposure.

-5-
Work area safety
Keep work area clean and well
lit. Cluttered or dark areas invite
accidents.
DO NOT operate the laser tool around
children or allow children to operate
the laser tool. Serious eye injury
could result.
DO NOT use instruments, attachments
and accessories outdoors when
lightening conditions are present.
Electrical safety
Batteries can explode or leak, cause
injury or fire. To reduce this risk,
always follow all instructions and
warnings on the battery label and
package.
Remove the batteries from the tool
when not using it for extended
periods. When storing for extended
periods, the batteries can corrode
and discharge themselves.
DO NOT short any battery terminals.
DO NOT charge alkaline batteries.
DO NOT mix old and new batteries.
Replace all old batteries at the same
time with new batteries of the same
brand and type.
DO NOT mix battery chemistries.
Dispose of or recycle batteries per
local code.
DO NOT dispose of batteries in fire.
Keep batteries out of reach of
children.
Personal safety
Stay alert, watch what you are
doing and use common sense
when operating a tool. Do not use
a tool while you are tired or under
the influence of drugs, alcohol or
medication. A moment of inattention
while operating a tool may result in
serious personal injury or incorrect
measurement results.
Use safety equipment. Always wear
eye protection. Safety equipment
such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal
injuries.
DO NOT use the laser viewing glasses
as safety goggles. The laser viewing
glasses are used for improved
visualization of the laser beam, but
they do not protect against laser
radiation.
DO NOT use the laser viewing glasses
as sun glasses or in traffic. The
laser viewing glasses do not afford
complete UV protection and reduce
color perception.
DO NOT use any optical tools such
as, but not limited to, telescopes

-6-
or transits to view the laser beam.
Serious eye injury could result.
DO NOT stare directly at the laser
beam or project the laser beam
directly into the eyes of others.
Serious eye injury could result.
Use caution when using instruments
in the vicinity of electrical hazards.
Magnets
IEC 60825-1:2007-03
<
1 mW, 635 nm
Keep the tool and laser
detector away from
cardiac pacemakers. The
magnets of the tool and
laser detector generate a field that
can impair the function of cardiac
pacemakers.
Keep the tool and laser detector away
from magnetic data medium and
magnetically-sensitive equipment.
The effect of the magnets of the
tool and laser detector can lead to
irreversible data loss.
Use and care
Use the correct tool for your
application. The correct tool will do
the job better and safer.
Do not use the tool if the switch does
not turn it on and off. Any tool that
cannot be controlled with the switch
is dangerous and must be repaired.
Store idle tool out of the reach of
children and do not allow persons
unfamiliar with the tool or these
instructions to operate the tool.
Tools are dangerous in the hands of
untrained users.
Maintain tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
operation. If damaged, repair tool
before use. Many accidents are
caused by poorly maintained tools.
Use the tool, accessories, etc., in
accordance with these instructions
and in the manner intended for the
particular type of tool, taking into
account the working conditions and
the work to be performed. Use of
the tool for operations different from
those intended could result in a
hazardous situation.
SAVE THESE INSTRUCTIONS.
INTENDED USE
The instrument is intended for determining and checking horizontal and
vertical lines, as well as 90-degree layout and alignment. The instrument is
suitable for indoor and may be used outdoors with optional receiver.

-7-
FEATURES
The numbering of the product
features shown refers to the
illustration of the instrument on the
graphic page.
1. Operating mode keypad
1a. On/Off button and Operating
Mode button
1b. “Pulse” Mode button, for use
with line laser receiver
1c. “Pulse” mode indicator
1d. Manual/Lock indicator
1e. Low battery level indicator
2. Exit opening for laser beam -
produces 360-degree horizontal
laser line
3. Exit opening for laser beam -
produces 360-degree vertical
laser line from the side
4. Exit opening for laser beam -
produces 360-degree vertical
laser line from the front
5. Battery compartment/lid
6. Switch for automatic leveling/
locking the unit
TECHNICAL DATA
Description LL360P
Accuracy: 1/4-in at 100-ft
(3mm at 15m)
Range: 65-ft (20m)
Range with Detector (Optional): 165-ft (50m)
Leveling Type: Electronic (±2.5º)
Beam Rating: Class 2M, 635nm
Operating Temperature: 14º F to 122º F
(-10º C to 50º C)

-8-
PREPARATIONS
Description LL360P
Storage Temperature: -4º F to 140º F
(-20º to 60º C)
Power Supply: Three (3) AA cell alkaline provide
approx. 5 hours on continuous
work
Water/Dust Protection IP54
Net Weight: 2.9lb (1.3kg)
Inserting/Replacing Batteries
Rechargeable or alkaline batteries
are suitable for use to power your
instrument.
!WARNING Always replace all
alkaline batteries at
the same time. Only use batteries
from one brand and with the identical
capacity.
Remove the batteries/pack from the
tool when not using it for extended
periods. When storing for extended
periods, the batteries can corrode and
discharge themselves.
To open the battery compartment
5, press on the latch and fold the
battery lid upward.
Insert the batteries. When inserting,
pay attention to the correct polarity
according to the “+” and “-” icons
inside of the battery compartment.
Use either alkaline batteries or
Ni-Mh batteries. When inserting
alkaline batteries, pay attention to
the correct polarity according to the
representation on the inside of the
battery compartment. Always replace
all batteries at the same time. Only
use batteries from one brand and
with the identical capacity.
Remove the batteries from the
tool when not using it for extended
periods. When storing for extended
periods, the batteries can corrode
and discharge themselves.

-9-
OPERATION
!WARNING Do not subject the
instrument to
extreme temperatures or variations in
temperature. As an example, do not
leave it in vehicles for long time. In
case of large variations in
temperature, allow the instrument to
adjust to the ambient temperature
before putting it into operation. In
case of extreme temperatures or
variations in temperature, the
accuracy of the instrument can be
impaired.
Avoid heavy impact to or falling
down of the instrument. After severe
exterior effects to the instrument,
it is recommended to carry out an
accuracy check each time before
continuing to work.
This laser tool is a precision
instrument and should be treated
with care.
When not in use, the pendulum 6
should always be in the OFF position.
Locking the pendulum 6allows the
laser to better withstand vibration and
trauma incurred during transportation
or if the unit is dropped.
Switching On and Off
To switch on the tool, slide the On/
Off switch 6 to the position (when
working without automatic leveling)
or to the ON position (when working
with automatic leveling).
Immediately after switching on, the
tool sends laser beams out of the exit
openings.
Operating Modes
The tool has total of three operation
modes that can be switched through
in sequence:
– Horizontal Layout Operation:
Produces a 360-degree horizontal
laser plane
– Vertical Layout Operation:
Produces a two vertical laser
planes at a 90° angle
– 3-Plane Layout Operation:
Produces a horizontal laser line in
the front.
After switching on, the tool is in
horizontal layout operating mode with
self-leveling. To change the operating
mode, press the operating mode
button 1a as often as required until
the requested operating mode is set.
All operating modes can be selected
both with and without automatic
leveling.

-10-
Store and transport the tool only in
the supplied protective case.
Keep the tool clean at all times.
Do not immerse the tool into water or
other fluids.
Wipe off debris using a moist and soft
cloth. Do not use any cleaning agents
or solvents.
Regularly clean the surfaces at the
exit opening of the laser in particular,
and pay attention to any fluff of fibers.
If the tool should fail despite the care
taken in manufacturing and testing
procedures, repair should be carried
out by an authorized after-sales
service center for Dave White’s SitePro
instruments.
In all correspondence and spare parts
orders, please always include the
model number and serial number of
the instruments.
All precision instruments should
be cleaned, lubricated, checked
and adjusted ONLY at a qualified
instrument repair station or by the
manufacturer, at least once a year.
In case of repairs, send in the
instrument packed in its protective
case.
ENVIRONMENT PROTECTION
Recycle raw materials
& batteries instead of
disposing of waste.
The unit, accessories,
packaging & used
batteries should be
sorted for environmentally friendly
recycling in accordance with the
latest regulations.
MAINTENANCE AND SERVICE
Pulse Mode
The Pulse (Receiver) Mode allows
the laser tool to be used with the
optional line laser receiver. To
activate this mode, press the Pulse
Mode button 1b. The Pulse Mode
indicator 1c will light up green.
When not using the tool, switch it off
in order to extend battery life.

-11-
LIMITED WARRANTY
Dave White’s SitePro (“Seller”) warrants to the original purchaser only, that all David
White laser tools and optical instruments will be free from defects in material or
workmanship for a period of two (2) years from date of purchase.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited
Warranty and, to the extent permitted by law, any warranty or condition implied by
law, shall be the repair or replacement of parts, without charge, which are defective
in material or workmanship and which have not been misused, carelessly handled, or
misrepaired by persons other than Seller or Authorized Service Center. To make a claim
under this Limited Warranty, you must return the complete laser, optical instrument
or David White product, transportation prepaid, to SITEPRO Service Department or
Authorized Service Center. Please include a dated proof of purchase with your tool. For
locations of nearby service centers, please call 1-855-354-9881.
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH
AS TRIPODS, RODS, HAND LEVELS, FIELD SUPPLIES, TAPES, MOUNTING
DEVICES AND OTHER RELATED ITEMS. THESE ITEMS RECEIVE A 90 DAY LIMITED
WARRANTY.
To make a claim under this Limited Warranty, you must return the complete product,
transportation prepaid. For details to make a claim under this Limited Warranty please
visit www.davidwhite.com or call 1-855-354-9881.
ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR
FROM DATE OF PURCHASE. SOME STATES IN THE U.S., AND SOME CANADIAN
PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME
STATES IN THE U.S., AND SOME CANADIAN PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S.,
OR PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE
UNITED STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO
RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR
LOCAL SITEPRO DEALER OR IMPORTER.
David White is a registered trademark and offered exclusively by SitePro.

42347DLL360 10/15 Printed in China
© Dave White’s SitePro 7619 S 1150 E Otterbein, IN 47970
Tel. [phone]