DayStar KJ71060BK User manual

KJ71060BK Page 1 INS71060
www.Daystarweb.com
Tech Support Contact Info
[email protected]
Phone: [phone]
Fax: [phone]
841 South 71st Avenue
Phoenix, AZ 85043
KJ71060BK
2007 - 2018 Jeep Wrangler JK Radio Mount Kit
Instructions Sheet INS71060
2018 Daystar Products International
Version: 00
Bill of Materials
Part Number
Description
Quantity
M56281-BK
JK Radio Mount Switch Panel
1
RM25R-U/V
Dual Band Radio, 25W
1
DB-RM
Dual Band Radio Antenna
1
NMO-MT-U
Antenna Mount
1
KU80011
Rocker Switch, 20 A, Blue
1
KU80012
Rocker Switch, 20 A, Green
1
KU80013
Rocker Switch, 20 A, Amber
1
KU80014
Rocker Switch, 20 A, Red
1
BU71060
Hardware
1
Required Tools
Trim Removal Tools
Metric Tool Set
Screwdriver Set
Drill
Drill Bit Set

KJ71060BK Page 2 INS71060
Pre-Install Procedure
1. Remove roof panels
a. Disengage locks and remove each panel

KJ71060BK Page 3 INS71060
Installation
2. Locate desired position of radio mount on upper
dash panel
a. Recommend positioning at the center, above
the rear view mirror, between the driver and
passenger visors
3. Firmly press mount against upper dash panel and
mark location of holes

KJ71060BK Page 4 INS71060
4. Remove upper dash panel
5. Bore out holes with an adequate drill and bit
a. Verify supplied screws fit and securely hold
mount to upper dash panel
6. Install radio into corresponding hole on radio mount
a. Insert radio and fasten using supplied
hardware

KJ71060BK Page 5 INS71060
7. Install rocker switches into corresponding holes on
radio mount
a. Slide each switch in until they lock into place

KJ71060BK Page 6 INS71060
8. Assemble antenna mount bracket 9. Install antenna mount bracket onto driver side
window frame

KJ71060BK Page 7 INS71060
10. Install radio antenna

KJ71060BK Page 8 INS71060
11. Run antenna cable along door jam and behind dash
panels
12. Install radio electrical wiring
a. Run positive from positive battery terminal
b. Ground negative to the body of the vehicle

KJ71060BK Page 9 INS71060
13. Reinstall upper dash panel
a. Leave cables hanging out behind upper dash
panel
14. Connect cables and wiring to corresponding
connectors behind radio

KJ71060BK Page 10 INS71060
15. Install radio mount
a. Tuck cables behind radio mount
b. Align radio mount and upper dash panel holes,
and fasten using supplied screws

KJ71060BK Page 11 INS71060
16. Locate desired position of microphone mount
a. In this case, the driver side visor was used
17. Firmly press mount against surface and bore out
holes with a drill and bit
a. Be sure not to drill all the way through the
visor, if that is the desired position of the
microphone mount
b. Verify supplied screws fit and securely hold
mount to surface

KJ71060BK Page 12 INS71060
18. Insert microphone onto holder

KJ71060BK Page 13 INS71060
19. Install complete Post Installation
20. Check all fasteners to ensure they are tightened to
proper specifications.
21. Ensure all wires, hoses, cables, etc. are properly
connected and there is ample slack.
Thank you for choosing Daystar Products
Daystar recommends a certified technician install this
system. In addition to these instructions, professional
knowledge of disassemble/reassembly procedures as well
as post instructions checks must be known. Attempts to
install this system without this knowledge and expertise
may jeopardize the integrity and/or operating of the
vehicle.
Please read all the instructions before beginning the
installation. Check the kit hardware against the parts list.
Be sure you have all the needed parts and understand
where they go. If anything is missing, do not proceed with
the installation, Call Daystar Products to obtain needed
items.
ESTABLISHED IN 1977