Firstech FTI-HDP7 User manual

CM-900
CM-900S/900AS
CM7X00
CM7000/7200 Cut loop for A/T
CM900AS/900S Jumper
DEREK ZOOLANDER
Est. 2001
CENTER KIDS
WHO CAN’T READ GOOD
A
N
D
W
H
O
W
A
N
N
A
L
E
A
R
N
T
O
D
O
O
T
H
E
R
S
T
U
F
F
G
O
O
D
T
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
for
Green White/BluePark / Auto
I/O Changes
ClutchPCU
Lights
CANInstallYearModelMake
FEATURE COVERAGE
PARKING LIGHTS
AUTOLIGHT CTRL
TACH OUTPUT E-BRAKE STATUS
BRAKE STATUS
HOOD STATUS TRUNK STATUS
DOOR STATUS
TRUNK/HATCH RELEASE
DISARM OEM ALARM ARM OEM ALARM
DOOR UNLOCK
DOOR LOCK
A/M RS CONTROL
IMMOBILIZER DATA
REQUIRED CONFIGURATION
C
REQUIRED CONNECTIONS - SEE NOTES
B
REQUIRED CONNECTIONS (COLORS VARY)
A
This installation requires BLADE-AL(DL)-HA6 firmware, flash module and update the controller firmware before installing.
PCU:
Vehicle PCU locations differ by model, please note the specific locations according to the component locator, and also note
that the 36-pin connector at the Smart PCU can be either lt. brown or gray.
Lights:
( - ) Parking lights connections are provided by the included headlight switch adapter, please ensure proper configuration
to avoid damaging the vehicle’s headlight switch. See detailed illustration on wiring page for specific configuration required.
The FTI-HDP7 kit includes a headlight switch adapter equipped with pre-terminated wires that must be inserted into the
gray I/O connector of a compatible Firstech control module. Replace the pk light and status wires from the I/O connector.
To avoid possible damage to the vehicle headlight switch, please confirm proper configuration of the included adapter.
FTI-HDP7: Installation and Configuration Notes
FTI-HDP7: Vehicle Coverage and Preparation Notes
RLX PTS AT 2016-20 Type 1 PCU Type B NFB N/A N/A
DL-HA6
Acura

FTI-HDP7 - DL-HA6 - Type 1
Smart PCU
PWR
BLADE
2
Headlight Switch
66 11
7
1
2121
2
11
81
63 9191
10101
1111
0202
11
81
63 9191
Gray or lt.brown
Gray
C
B
A
B A
1
1
Takeover not supported: Vehicle engine will shut down when
doors are opened.
Caution: Using the wrong connector will damage the light switch.
Please refer to the light configuration notes on the coverage page.
LED Programming Error Codes
Module LED flashing RED during programming
1x - CAN error, check connectors
2x - Klon error, check connections, retry programming
if error persists, perform a clearing flash then retry
programming with all doors closed
3x - Immobilizer error, check connectors, confirm car starts
4x - VIN error, check connectors, re flash using vehicle entry
2016-20 Acura RLX PTS AT

Patent No. US 8,856,780 CA 2759622
INSTALL GUIDE
WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020
CARTRIDGE INSTALLATION
1Slide cartridge into unit. Notice
button under LED. 2Ready for Module Programming Procedure.
MODULE PROGRAMMING PROCEDURE
12 Module Programming
Procedure completed.
11 Press UNLOCK on the OEM
remote.
x1
2Turn ignition to ON position.
ENGINE
START
STOP
OFF ACC ON START
ON 8Turn ignition to ON position.
ENGINE
START
STOP
OFF ACC ON START
ON
4Turn ignition to OFF position.
OFF ACC ON STARTOFF
ENGINE
START
STOP
10 Turn ignition to OFF position.
OFF ACC ON STARTOFF
ENGINE
START
STOP
5WARNING:
Disconnect power last.
Disconnect RS from vehicle.

7WARNING: Do not press RS
programming button.
Connect power first.
Connect RS to vehicle.

6Connect RS to computer
and proceed with extended
programming.

3Wait, LED will flash BLUE
rapidly.
9Wait, LED will turn solid BLUE
for 2 seconds.
!If the vehicle is equipped with a power liftgate: Open and
close the power liftgate with the OEM keyfob.
1Close driver door.
Re-open driver door to wake up
data bus.
Page 40 of 41 COM-BLADE-AL(DL)-HA6-EN 20210503
Doc. No.: ##75672##
ALL IN ONE
HONDA/ACURA