Dea system 203 2 User manual

DEA SYSTEM s.r.l.

Via Monte Summano 45/E , 36010 Zanè

(VI) - Italy

Tel.+39.0445.314944 Fax +39.0445.314334

http://www.deasystem.com

e-mail: deasystem@deasystem.com

203_2

Document Number F12030

Rev 01 Date 17/12/02

filename F1203001.pub

CENTRALE DI COMANDO

UNITÉ DE COMMANDE

ISTRUZIONI D’ USO E DI INSTALLAZIONE

INSTRUCTIONS D’UTILISATION ET D’INSTALLATION

E CENTRAL DE MANDO INSTRUCCIONES DE USO Y DE INSTALACION

GB CONTROL UNIT INSTALLATION AND USER’S MANUAL

P QUADRO DE COMANDO INSTRUÇÕES DE USO E DE INSTALAÇÃO

This booklet is an integral and essential part of the product and must be delivered to the

user. Carefully read the warnings contained inside that provide important information

regarding safety during installation, use and maintenance.

OVERVIEW

The DEA 203_2 control panel has been designed to control the “DEA SYSTEM” automa-

tion devices for both sliding gates and garage doors powered by 230V single-phase

motors, and comes complete with electronic motor force adjustment, amperometer

control for the detection of any obstacles present and an inertia limitation system for

use with sliding gates. The widest versatility, easy installation and complete respect for

the European regulations in force regarding electromagnetic compatibility and electric

safety are the unit's main characteristics; in particular, DEA SYSTEM ensures conformity

to the following European Directives: 89/336/EEC, 73/23/EEC and subsequent amend-

ments.

DEA SYSTEM reminds all users that the selection, configuration and installation of all the

devices and materials in the entire automation must be performed in respect of the

regulations in force in the nation of installation.

TECHNICAL DATA

Power supply 230V AC +/- 10% 50 Hz

Flashing light output :230V AC 50 Hz max 40W

Gate open signal light/courtesy light output :230V AC 50 Hz max 40W

Auxiliary power supply output :24V AC max 200 mA

Electric lock output :12V AC max 15V A

Max. motor power :500W

Fuse F1 :160 mA 250V

Fuse F2 5A 250V

Max pause time :80 s

Max work time :160 s (sliding version)

:80 s (garage door version)

The work time you set must anyway allow to respect the maximum working time admit-

ted for the type of motor you are using. Please refer to the data on the motor label.

ELECTRICAL SYSTEM CONFIGURATION

(See fig. 1)

IMPORTANT: Any installation, maintenance, cleaning or repair operations on any part

of the automatism must be performed exclusively by qualified personnel, and all such

operations must be performed only after first disconnecting the power supply. Always

keep the 230V cables (power supply, motor, starting condenser, flashing light, courtesy

light) separate from the low voltage cables (controls, electric lock, antenna, and auxil-

iary power supply) and fasten these latter using adequate clamps near the terminal

boards. Install a multiple pole switch with a contact opening of 3 mm provided with

protection against overloads upstream from the automatism. Use a cable with a mini-

mum section of 3X1.5 mm² (such as H07RN-F type) for the power supply and scrupu-

lously respect all the regulations in force regarding electrical systems in the nation of

installation.

TERMINAL BOARD CONNECTION:

(See fig. 1)

1-2: Power supply: 230V AC +/-10% 50 Hz (F = phase, N = neutral)

3-4 Courtesy light output 230 V AC 50 Hz max 40W (DIP8 = ON)

Gate open indicator light output: 230 V AC 50 Hz max 40W (DIP8 = OFF)

5-6 Flashing light output: 230 V AC 50 Hz max 40W

7-8-9 Motor output (7 = open, 8 = common, 9 = close)

10-11 electric lock output 12V AC 15VA

12 Common inputs

13 FCA opening limit-switch input (N.C.) stops the motor's opening stroke

14 FCC closing limit-switch input (N.C.) stops the motor's closing stroke

15 APRE PEDONALE opens the gate to a width of only 1.5 (N.O.)

16 FOTO Photocell Art. 104/105 input (N.C) inverts movement during closing, and

if enabled during opening stops movement

17 STOP stop button input (N.C) stops movement in any situation

18 APRE open/close button input (N.O.) can function in both step-by-step mode

and inversion mode

IMPORTANT: All N.C. inputs not used must be bridged towards the common inputs

terminal.

19 Antenna ground

20 Antenna signal

21-22 Auxiliary power supply output: 24V AC max 200mA

J3 Radio receiver plug-in connector

OPERATION:

TIME SETTING

TCA trimmer for the setting of the automatic closing time, after which the gate will

automatically close again.

TLAV trimmer for the setting of the work time, after which the motor will stop during

both opening and closing.

Whenever the limit-switches are installed, the work time must be set to a value

that is a few seconds higher than the real time required for the stroke of the

motor.

FORCE ADJUSTMENT

The 203_2 control panel is equipped with a device that permits the electronic adjust-

ment of motor force by adjusting the “forza” trimmer:

“FORZA”:adjusts the intensity of the motor force during the stroke (rotate

clockwise to increase force, counter-clockwise to decrease force).

The motor force must be adjusted by keeping trimmer R32 “SENS” in

the MIN. position (entirely in clockwise direction) in order to avoid

the undesired intervention of the REVERSER. The sensitivity of the

reverser is made subsequently (see "Reverser operation”).

REVERSER OPERATION

Whenever the “reverser” device is used, the limit-switches must also be installed

After setting the motor force, proceed to the setting of reverser sensitivity. Make sure

that the reverser is enabled (DIP7 OFF) and with the sensitivity set at minimum level

(trimmer R32 turned entirely clockwise) perform an opening movement. During closing,

stop the gate and slowly increase the reverser sensitivity (trimmer R32 turned counter-

clockwise) until the reverser intervenes (inversion of direction of movement). This

permits the identification of the sensitivity necessary for the intervention of the re-

verser as soon as the motor stops.

In any case, we recommend setting a sensitivity that is SLIGHTLY lower in order to

avoid the undesired intervention of the reverser by mechanical friction.

The position of DIP2 determines the reaction to the perception of the obstacle, and in

particular:

•DIP 2 ON : during both opening and closing, the intervention of the reverser

inverts the direction of movement for 3 seconds and then stops it.

•DIP 2 OFF : during opening, the intervention of the reverser stops movement,

and during closing inverts the direction of movement.

It is in any case obligatory to use appropriate safety devices in order to ensure the

impact force limitation values prescribed by the regulations in force in the nation of

installation.

DIP-SWITCHES FUNCTIONS

DIP1

OFF

ON “collectivity” function enabled: does not receive opening pulses

during opening and the gate open pause time

“collectivity” function disabled: receives opening pulses also during

opening and the gate open pause time

DIP2 OFF

ON See description “reverser operation”

See description “reverser operation”

DIP3

OFF

ON “step-by-step” program: OPEN->opening, OPEN->stop, OPEN-

>closing...

“inversion” program: OPEN->opening, OPEN->closing, OPEN-

>opening...

DIP4

OFF

ON Sliding version: closing limit-switch delay disabled, anti-inertia de-

vice enabled

Garage door version: closing limit-switch delay enabled, anti-inertia

device disabled

DIP5

OFF

ON Photocell operative also during opening: stops all movement until the

obstacle is removed

Photocell operative only during closing: inverts direction of movement

DIP6 OFF

ON automatic closing disabled: after opening, it closes again only after

an opening pulse

automatic closing enabled : after opening, and after the pause time

set, the gate automatically closes again

DIP7

OFF

ON Reverser disabled

Reverser enabled.

IMPORTANT: limit-switches compulsory

DIP8

OFF

ON Terminals 3-4: courtesy light output 230V AC 50 Hz (delay: 50 sec-

onds)

Terminals 3-4: gate open signal light output, 230V AC, 50 Hz

203_2

N.C.

fig. 1

N.C.

STOP

APRE N.O.

N.C.

PED. N.O. START PEDONALE

OUVERTURE PIETONS

PEDESTRIAN OPEN

APERTURA PEATONAL

BLOCCO

BLOCAGE

STOP

BLOQUE

BLOQUEIO

START/APRE

START/OUVRE

START/OPEN

START/ABRE

FOTOCELLULA art. 104 / 105

PHOTOCELLULE art. 104 /105

POHOTOCELL item 104 /105

FOTOCELLULA art. 104 / 105

FOTOCÉLULA art. 104/105

1 2 3 4 5

FCA FCC N.C.

FINECORSA CHIUSURA

BUTÉE DE FIN DE COURSE EN FERMETURE

CLOSING LIMIT SWITCH

FIN DE CARRERA CIERRE

FIM DE PERCURSO FECHAMENTO

FINECORSA APERURA

BUTÉE DE FIN DE COURSE EN OUVERTURE

OPENING LIMIT SWITCH

FIN DE CARRERA ABERTURA

FIM DE PERCURSO ABERTURA

LAMPEGGIANTE 230Vac 50Hz 40W max

CLIGNOTEUR 230Vac 50Hz 40W max

FLASHING LIGHT 230Vac 50Hz 40W max

LAMPARA INTERMITENTE 230Vac 50Hz 40W max

PISCA - PISCA 230 V. c. a. 50 Hz máx. 40W

LUCE DI CORTESIA / SPIA CANCELLO APERTO 230Vac 50Hz 40W max

LAMPE DE COURTOISIE / VOYANT PORTAIL OUVERTE 230Vac 50Hz 40W max

COURTESY LIGHT / OPEN GATE WARNING LIGHT 230Vac 50Hz 40W max

LUZ DE CORTESIA / INDICADOR LUMINOSO PUERTA ABIERTA 230Vac 50Hz 40W max

LUZ DE CORTESIA / INDICADOR LUMINOSO PORTÃO ABERTO 230 V. c. a. 50 Hz máx. 40 W

ELETTROSERRATURA 12Vac 15VA

SERRRURE ELECTR. 12Vac 15VA

ELECTRIC LOCK 12Vac 15VA

ELECTROCIERRE 12vaC 15VA

FECHADURA ELÉCTRICA

ATTENZIONE: DEA SYSTEM ricorda tuttavia che la scelta ,la disposizione e l’installazione di tutti i dispositivi e materiali che compongono l’intera automazione deve avvenire in ottemperanza alle normati-

ve vigenti nel paese in cui si effettua l’installazione.

ATTENTION: DEA SYSTEM vous rappelle toutefois que le choix, la disposition et l’installation de tous les dispositifs et de tous les matériels qui font partie de l’automation complète doivent être exécutés

conformément aux réglementations en vigueur dans le pays où l’installation sera mise en place.

ATENCIÓN!: DEA SYSTEM, no obstante, recuerda que la elección, la disposición y la instalación de todos los dispositivos y materiales que componen el automatismo debe efectuarse en el cumplimiento

de las normativas en vigor en el país en el que se efectúa dicha instalación.

WARNING: DEA SYSTEM reminds however that the choice and installation of all devices and materials included in the complete automation must respect the legal norms in force in the country where the

system is installed

ATENÇÃO: Entretanto o DEA SYSTEM lembra que a escolha, a disposição e a instalação de todos os dispositivos e materiais que constituem a inteira automação, devem ser efectuadas a obedecer