DEI DEI-737CR User manual

TAIWAN DEI
-737CR-737CR
INSTRUCTION
DESCRIPTION OF CORDLESS REMOTE
ON
OFF
3
4
2
1
5
POWER
Fan speed button
Select fan speed
HIGH / MID / LOW /AUTO
Display this symbol while
Auto-on timer is set
Signal transmission indicator
Power
Power on/off button
Select swing direction
of fan outlet or auto-swing
(ceiling hidden-no swing)
Louver control button(inactive)
Select cooling,heating
fan or dehum. Modes
,
Sleep Mode
Button to set sleep mode
I HR. OFF TIMER
Display of set temperature
Display the choosen fan speed
Display the swing of fan
outlet
Display set time
Timer
For auto-on timer setting or
auto-off timer setting
Display the operating mode :
Display this symbol while
Auto-off timer is set
COOL
DEHUM.
FAN
HEATING
MODE
SLEEP
FAN
SWING
Off / 1 hr.
Auto off after one hour
Operation Mode
Display of sleep mode
Temperature/Time Setting
Button to increase or decrease
the temperature or time

1. CAUTIONS
2.1 Please make sure the power is switched off before installment to avoid electric shock.
2.2 Please check the correct voltage corresponding to the same controller's power switch
power supplying.
2.3 The installation of this product should be away from humid place.
2.4 The output contact capacity shows on the specification. Do not over load.
2.5 Please read the operation maunal carefully before installation. If damages are caused
wiring, products would not be guaranteed.
2. SPECIFICATION
2.3 Power Supply AC110V/220V 10%, 50/60Hz single phase
2.4 Sensor Range 5
3. OPERATING MODES
3.1 Operating mode Cooling/Heating/Fan/Dehumidifying
3.2 Setting range 16 30 (under Cooling) ;
3.7 4-way valve activities The 4-way valve relay contacts-- except heating contacts stays
remain open.
4. FUNCTIONS
4.1 Descriptions of functions in Modes
Cooling Mode
when Room temp.
Heating Mode
before
by incorrectly
2.1 Dimension :
Receiver : 47mm(diameter) 1mm
Power box : 140mm (L) x 78mm (H) x 73mm (W) 1mm
2.2 Operating Environment :
Operating temp. : 0 ~ 50 ; Storage temp. : -10 ~ 65 ,
RH30% ~ 90% (non-condensing)
:
: ~45
2.5 Max. Securied Electrocity Loading : compressor ---25(7)A/250VAC
fan--- 3A/250VACX3; 4-way Valve for cooling-heating--3A/250VAC
:
: 16 32 (under Heating)
3.3 Fan control : Auto-fan/High/Mid/Low
3.4 Sleep mode : only available under Cooling or Heating.
3.5 Auto-on/Auto-off timer : setting range 1 12hours
3.6 Backup power button : the backup power button designed on Receiver can turn on
and off the controller for emergency in the case of remote control failure.
:
unactivated, always
:
Set temp.,green LED on and the compressor on.(Green LED flashes
while compressor in 3-minutes cushion time operation protection);when Roomtemp. Set temp.
-2 ,green LED flashes and the compressor off.
:
when Room temp. Set temp.,red LED on and the compressor on.(Red LED flashes
while compressor in 3-minutes cushion time operation protection);when Room temp.
Set temp. -2 , red LED flashes and the compressor off.
Version 01
Fan : If selecting continuous fan mode, the green LED flashes.
Dehumidifying : If selecting dehumidifying mode, the compressor works as 10 minutes on
and 10 minutes off. In this cycle, the fan speed turns into low s peed. If
the Room temp. is lower than 16 ,the compressor contact remains off.
Sleep Mode : In cooling mode, when this function is set, then the temperature will go
up 1 after one hour of setting (in heating mode, it will go down 1 );
then at the second hour, the temperature will go up another 1 (in
heating mode, it will go down another 1 ) ; then this final temperature
will be remained.
(The highest limitation of setting temperature is 30 and the lowest
limitation is 16 )
Setting Reservation clock
After pre-setting timer for operation, the controller will be
power-on or power-off according to the pre-set time.
The workable distance of the receiver : as below illustration
5. ERROR MESSAGE
If sensor is failed,the red LED on receiver flashes quickly. To solve the problem by
checking the connection of sensor or replacing a new sensor. If the orange led freashes
quickly, it means the internal circuit is failed. In this case, products should be sent back
to the factory for repair.
4.2 Descriptions of DIPSW function :
SW2(only for DEI-737C) :
ON --- with three minutes cushion operation protection for compressor
OFF--- without three minutes cushion operation protection for compressor(Default)
ON --- fan running continously (Default)
OFF--- fan running accompany with the on-off of 3-way valve.
45
45 Maximum transmission range is 7M
Externals of Receiver
Backup power button
Indicative LED
-737CR Operation Manual-737CR Operation Manual
5INS00198