Delfield F2000 Series User manual

F2000 and F17 Series Equipment Stands
Service, Installation and Care Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of
damage! Inspect all components immediately. See page 2.
July 2012
Important Information
Read Before Use
Please Save These Instructions!
Delfield
™
®
Warning
To assure proper operation a 2" airspace must be maintained between the lowest part of any cooking equip-
ment and the top of this unit. Cooking equipment must have a barrier (i.e. bottom, drip pan) between its heat
source and the top of the equipment stand. Failure to comply with this could severely damage the equipment
stand and void all warranties.

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
2
Delfield
™
®
WARNING Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment.
WARNING Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death.
WARNING Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other
Appliance.
WARNING Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment.
WARNING This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have
Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For Their
Safety.
WARNING This Appliance Is Not To Be Played With.
WARNING Do Not Clean With Water Jet.
WARNING Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance.
CAUTION Observe the following:
• Minimum clearances must be maintained from all walls and combustible materials.
• Keep the equipment area free and clear of combustible material.
• Allow adequate clearance for air openings.
• Operate equipment only on the type of electricity indicated on the specification plate.
• Unplug the unit before making any repairs.
• Retain this manual for future reference.
Important Warning And Safety Information

F2000/F17 Series Equipment Stand Service and Installation Manual
3
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
Receiving And Inspecting .....................................................3
F2000 Specifications.............................................................4
F17 Specifications.................................................................5
Installation ........................................................................ 6-7
Operation ..............................................................................7
Temperature Control Settings ...............................................8
Maximum Cooking Equipment Weight Capacity ...................8
Maintenance.................................................................... 9-10
Refrigerator Wiring Diagrams.............................................11
Freezer Wiring Diagrams ....................................................12
Replacement Parts by Model........................................ 13-16
Condensing Unit Assemblies ........................................ 17-18
Evaporator Coil Assemblies ................................................19
Drawer Assemblies .............................................................20
Replacement Part Prints .....................................................21
Standard Labor Guidelines..................................................22
Warranties..................................................................... 23-25
Notes ............................................................................ 26-27
©2012 The Delfield Company. All rights reserved. Reproduction without written permis-
sion is prohibited. “Delfield” is a registered trademark of The Delfield Company.
The serial number on remote models is located behind the 6"
(15cm) stainless steel panel.
The serial number on self-contained models is located in the
compressor housing.
The serial number tag shows the refrigerant used and the
amount of charge and amperage.
Always have the serial number of your unit available when
calling for parts and service.
Contents Serial Number Location
Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to the
delivering carrier immediately.
2. If damaged, open and inspect the contents with the carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment notify
the carrier. Notification should be made verbally as well as
in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
5. Check the lower portion of the unit to be sure legs or casters
are not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines are
secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been made
or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate. Remove
the front of the crate material, use of some tools will be required.
If the unit is on legs remove the top of the crate as well and lift
the unit off the skid. If the unit is on casters it can be "rolled" off
the skid.
Receiving and Inspecting the Equipment
All models are certified by:
National Sanitation Foundation (NSF)
Refrigerated models are certified by:
Underwriters Laboratories (UL)
Regulatory Certifications

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
4
Delfield
™
®
F2000 Specifications
Self Contained Low-Profile Freezer Base Equipment Stands
Model 12x20 Pan
Capacity
# Of Drawers Voltage/Hertz/
Phase
Amps H.P. Nema
Plug
Shipping Weight BTU
Load
BTU
System
Evap BTU/
TD/Temp
F2660 4 (2) 32" 115/60/1 11.0 1/2 5-15P 418lbs/190kg 925 1776 160/11º/-14º
F2694 8 (4) 32" 115/60/1 16.0 3/4 5-20P 500lbs/227kg 1558 2713 160/17º/-20º
Remote Low-Profile Freezer Base Equipment Stands
Model 12x20 Pan
Capacity
# Of Drawers Voltage/Hertz/
Phase
Amps H.P. Nema
Plug
Shipping Weight BTU
Load
BTU
System
Evap BTU/
TD/Temp
F2748 4 (2) 32" 115/60/1 10.0 N/A N/A 295lbs/134kg 1032 N/A 160/8º/-11º
F2776 8 (4) 32" 115/60/1 10.0 N/A N/A 375lbs/170kg 1770 N/A 160/12º/-15º
Remote Low-Profile Refrigerator Base Equipment Stands
Model 12x20 Pan
Capacity
# Of Drawers Voltage/Hertz/
Phase
Amps H.P. Nema
Plug
Shipping Weight BTU
Load
BTU
System
Evap BTU/
TD/Temp
F2852 4 (2) 19" (2) 27" 115/60/1 3.0 N/A N/A 278lbs/126kg 452 N/A 120/5º/32º
F2856 4 (2) 32" 115/60/1 3.0 N/A N/A 299lbs/136kg 461 N/A 120/5º/32º
F2862 6 (2) 19" (2) 27" 115/60/1 3.0 N/A N/A 331lbs/150kg 575 N/A 120/6º/31º
F2875 8 (2) 27" (2) 32" 115/60/1 3.0 N/A N/A 401lbs/182kg 717 N/A 240/4º/33º
F2880 8 (4) 32" 115/60/1 3.0 N/A N/A 428lbs/194kg 726 N/A 240/4º/33º
F2887 10 (2) 19" (4) 27" 115/60/1 6.0 N/A N/A 466lbs/211kg 868 N/A 240/4º/33º
F2899 12 (6) 27" 115/60/1 6.0 N/A N/A 530lbs/240kg 1029 N/A 240/5º/32º
F28110 12 (6) 32" 115/60/1 6.0 N/A N/A 588lbs/267kg 1143 N/A 240/5º/32º
Self Contained Low-Profile Refrigerator Base Equipment Stands
Model 12x20 Pan
Capacity
# Of Drawers Voltage/Hertz/
Phase
Amps H.P. Nema
Plug
Shipping Weight BTU
Load
BTU
System
Evap BTU/
TD/Temp
F2952C 4 (2) 32" 115/60/1 8.0 1/5 5-15P 398lbs/181kg 452 1727 120/14º/23º
F2956C 4 (2) 32" 115/60/1 8.0 1/5 5-15P 405lbs/184kg 461 1727 120/14º/23º
F2962C 6 (2) 19" (2) 27" 115/60/1 8.0 1/5 5-15P 479lbs/217kg 575 1727 120/14º/23º
F2975C 8 (2) 27" (2) 32" 115/60/1 10.0 1/4 5-15P 540lbs/245kg 717 2341 144/16º/21º
F2980C 8 (4) 32" 115/60/1 10.0 1/4 5-15P 578lbs/262kg 726 2341 144/16º/21º
F2987C 10 (2) 19" (4) 27" 115/60/1 10.0 1/4 5-15P 672lbs/305kg 868 2341 144/16º/21º
F2999C 12 (6) 27" 115/60/1 10.0 1/4 5-15P 691lbs/313kg 1029 2341 144/16º/21º
F29110C 12 (6) 32" 115/60/1 12.0 1/3 5-15P 766lbs/347kg 1143 2630 144/18º/19º

F2000/F17 Series Equipment Stand Service and Installation Manual
5
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
F17 Specifications
Open Shelf Equipment Stands
Model Length # Of Shelves Shelves Sq.
Ft.
# Of Drawers # Of 12x20
Pans
Shipping Weight
F17OS36 36” (91cm) 1 5.95 N/A N/A 200lbs/91kg
F17OS48 48” (122cm) 1 8.0 N/A N/A 250lbs/113kg
F17OS60 60” (152cm) 1 10.15 N/A N/A 300lbs/136kg
F17OS72 72” (183cm) 1 12.25 N/A N/A 350lbs/159kg
F17OS84 84” (213cm) 1 14.36 N/A N/A 400lbs/181kg
F17OS96 96” (244cm) 1 16.46 N/A N/A 475lbs/215kg
Dry Drawer Equipment Stands
F17DD32 32" (81cm) N/A N/A (1) 32” 2 290lbs/132kg
F17DD46 46" (117cm) N/A N/A (1) 19” (1) 27” 3 350lbs/159kg
F17DD54 54" (137cm) N/A N/A (2) 27” 4 390lbs/177kg
F17DD64 64" (163cm) N/A N/A (2) 32” 4 430lbs/195kg
F17DD73 73" (185cm) N/A N/A (1) 19” (2) 27” 5 475lbs/215kg
F17DD81 81" (206cm) N/A N/A (3) 27” 6 520lbs/236kg
F17DD96 96" (244cm) N/A N/A (3) 32” 6 600lbs/272kg
Self-Contained Refrigerated Base Equipment Stands
Model 12x20 Pan
Capacity
# Of Drawers Voltage/Hertz/
Phase
Amps H.P. Nema
Plug
Shipping Weight BTU Load BTU
System
Evap BTU/
TD/Temp
F17C52 4 (2) 32” 115/60/1 8.0 1/5 5-15P 410lbs/186kg 452 1727 120/14º/23º
F17C60 6 (2) 19” (2) 27” 115/60/1 8.0 1/5 5-15P 460lbs/209kg 556 1727 120/14º/23º
F17C68 8 (4) 27” 115/60/1 8.0 1/5 5-15P 500lbs/227kg 632 1727 120/14º/23º
F17C78 8 (4) 32” 115/60/1 10.0 1/4 5-15P 580lbs/263kg 726 2341 120/14º/23º
F17C87 10 (2) 19” (4) 27” 115/60/1 10.0 1/4 5-15P 625lbs/284kg 868 2341 144/16º/21º
F17C95 12 (6) 27” 115/60/1 10.0 1/4 5-15P 700lbs/318kg 1001 2341 144/16º/21º
F17C110 12 (6) 32” 115/60/1 12.0 1/3 5-15P 750lbs/340kg 1143 2630 144/16º/21º
Remote Refrigerated Base Equipment Stands
F17R44 4 (2) 32” 115/60/1 3.0 N/A N/A 300lbs/136kg 452 N/A 120/4º/33º
F17R52 6 (2) 19” (2) 27” 115/60/1 3.0 N/A N/A 350lbs/159kg 556 N/A 120/5º/32º
F17R60 8 (4) 27” 115/60/1 3.0 N/A N/A 396lbs/180kg 632 N/A 120/5º/32º
F17R70 8 (4) 32” 115/60/1 3.0 N/A N/A 450lbs/204kg 726 N/A 120/6º/31º
F17R79 10 (2) 19” (4) 27” 115/60/1 6.0 N/A N/A 525lbs/238kg 868 N/A 240/4º/33º
F17R87 12 (6) 27” 115/60/1 6.0 N/A N/A 560lbs/254kg 1001 N/A 240/4º/33º
F17R102 12 (6) 32” 115/60/1 6.0 N/A N/A 610lbs/277kg 1143 N/A 240/5º/32º
Self-Contained Freezer Base Equipment Stands
Model 12x20 Pan
Capacity
# Of Drawers Voltage/Hertz/
Phase
Amps H.P. Nema
Plug
Shipping Weight BTU Load BTU
System
Evap BTU/
TD/Temp
F17FC60 4 (2) 32” 115/60/1 12.0 1/2 5-15P 450lbs/204kg 1242 1776 160/11º/-14º
F17FC76 6 (2) 19” (2) 27” 115/60/1 16.0 3/4 5-20P 600lbs/272kg 1461 2713 160/17º/-20º
F17FC84 8 (4) 27” 115/60/1 16.0 3/4 5-20P 635lbs/288kg 1647 2713 160/17º/-20º
F17FC94 8 (4) 32” 115/60/1 16.0 3/4 5-20P 710lbs/322kg 1879 2713 160/17º/-20º
Remote Freezer Base Equipment Stands
F17FR48 4 (2) 32” 115/60/1 10.0 N/A N/A 360lbs/163kg 1242 N/A 160/8º/-11º
F17FR58 6 (2) 19” (2) 27” 115/60/1 10.0 N/A N/A 400lbs/181kg 1461 N/A 160/9º/-12º
F17FR66 8 (4) 27” 115/60/1 10.0 N/A N/A 475lbs/215kg 1647 N/A 160/10º/-13º
F17FR76 8 (4) 32” 115/60/1 10.0 N/A N/A 560lbs/254kg 1879 N/A 160/12º/-15º

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
6
Delfield
™
®
Location
This unit is intended for indoor use only. Be sure the location chosen has
a floor strong enough to support the total weight of the cabinet, cooking
equipment and contents. Reinforce the floor as necessary to provide for
maximum loading, for complete weight chart, please refer to page 7.
Good refrigeration is based on good air circulation inside and out.
Inside cabinet: Do not pack refrigerator so full that air cannot circulate.
Outside cabinet: Be sure that the unit has access to ample air to and from
the unit. If air flow is available to the rear of the unit that will help dissipate
exhaust air. In the event the unit is attached to the wall mount brackets,
it is important that air flow is available to the compressor compartment.
Allow air flow to the bottom of the unit as well, avoid hot corners when
possible. Allowing for the proper air flow and ventilation to the compressor
compartment will extend the life of the compressor as well as ensure proper
operation.
Cooking Equipment: WARNING! To assure proper
operation a 2" airspace must be maintained between
the lowest part of any cooking equipment and the top
of this unit. Cooking equipment must have a barrier
(i.e. bottom, drip pan) between its heat source and the
top of the equipment stand. Failure to comply with this
could severely damage the equipment stand and void
all warranties.
Leveling
A level cabinet looks better and will perform better because the drain
pan will drain properly, the doors will line up with the frames properly,
and the cabinet will not be subject to undue strain.
A unit on legs will have an adjustable bullet foot on each leg, adjust
each for a level unit. A unit on casters will not be adjustable. Be sure
the unit is on a level floor, make necessary changes to the floor for
proper level.
Lock all front casters to ensure the stability of the unit.
Wall bracket installation
A wall bracket kit is supplied to secure the equipment stand to an interior
wall. Some models are supplied on optional casters. These units must
also have the wall bracket installed during use.
The wall bracket must be installed properly and the
equipment stand firmly secured to it before using this
unit! Failure to observe this warning may result in
damage to the equipment and/or injury to the operator!
Never use the drawers as steps!
Do not overload the drawers or drop or throw product into the drawer
pans.
To install the wall bracket, follow these instructions:
1. Place the threaded rod through the front and rear
brackets in the compressor section. Thread the rod into
the wall bracket, making sure the longer bracket tabs
are above the height of the unit.
2. Tighten the rod until the bracket is held snug against the
back of the unit.
3. Move the unit against the wall at the desired location.
4. Secure the wall mount bracket to the wall using the top
two holes provided in the bracket tabs exposed above
the unit. The wall material must be capable of supporting
a minimum load of 300 pounds (136 kilograms) in the
vertical direction. All screws must be 1/4" diameter and
be capable of transferring the load from the bracket to
the wall.
5. Remove the threaded rod from the wall mount bracket
and move the unit away from the wall, leaving the bracket
attached to the wall.
6. Secure the bracket to the wall using the remaining four
holes.
7. Move the unit back into place and thread the rod back
into the wall mount bracket.
8. The unit should now be secured to the wall. Test the
mounting by pulling on the unit and checking that all
screws are tightened and the unit is firmly in place. If
the unit is secured, you may now place other equipment
on top of the stand and use the unit as required.
Never place any equipment on top of this unit without
first installing the wall bracket as shown above and
ensuring that the equipment is securely anchored and
stable.
9. To remove the unit in order to clean behind it,
first remove any equipment placed on top of the stand.
Then rotate the knob on the threaded rod counter-
clockwise to loosen and remove the rod from the bracket.
Before removing any cooking equipment
(including cooking oils) from the equipment stand,
allow time for the equipment to cool thoroughly.
Use extreme care in moving cooking equipment.
The threaded rod must be reinstalled and tightened
before returning the unit to service!
Be sure all cooking equipment resting on the equipment
stand is properly anchored. Consult the manufacturer’s
instructions for the cooking equipment to determine
the proper mounting technique. It is the owner’s and
operator’s responsibility to securely anchor cooking
equipment to the equipment stand.
Plumbing
Self-contained equipment stands come standard with a condensate
evaporator. If the condensate evaporator fails, the unit’s drain must
have an outlet to an appropriate drainage area or container.
Moisture collecting from improper drainage can create a
slippery surface on the floor and a hazard to employees.
It is the owner’s and operator’s responsibility to provide
a container or outlet for drainage.
Installation
CAUTION
WARNING

F2000/F17 Series Equipment Stand Service and Installation Manual
7
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
Drawer base equipment stands are designed and pre-set at the
factory to maintain a temperature of 36°F to 40°F (2°C to 4°C). A
solar-powered digital thermometer is located on the front of the
unit to allow monitoring of the drawer housing temperature.
The drawer housing temperature is controlled by a thermostat
located in the machine compartment. Continuous opening and
closing of the drawers will hamper the unit’s ability to maintain
optimum refrigeration temperature. Excess weight on top of the
unit will adversely affect the operation of the drawers.
The cooling coil is coated in epoxy to provide long-lasting service.
However, storing all acidic items, such as peppers and tomatoes
with lids that are sealable and immediately wiping up all spills of
either acid or base items will greatly extend the life of your unit.
Never stand on the unit or its drawers! They are not
designed to hold the weight of an adult, and may
collapse or unit may tip if misused in this manner.
Refrigerator Evaporator Fan Operation
When the refrigerator is initially powered up or immediately
following a power outage the unit will begin cooling after a 3-6
minute delay. During normal operation the evaporator fan pulses
independently of the compressor as dictated by the controller as
follows:
1. During the cooling mode, compressor and evaporator fan run
simultaneously.
2. During the compressor off mode, evaporator fan pulses three
minutes on and three minutes off.
3. During an actual defrost event other than the off-cycle
defrost, compressor stays off but the evaporator fan runs
continuously.
Cooling Cycle Defrost Cycle
Compressor On Compressor Off Compressor Off
Evap Fan
On
Evap Fan
Off
Evap Fan
On
Evap Fan
Off
Evap Fan
On
Evap Fan
Off
XCycles On 3-Min, Off
3-Min X
Electrical connection
Refer to the amperage data on page 3 & 4, the serial tag, your local
code or the National Electrical Code to be sure the unit is connected
to the proper power source. A protected circuit of the correct
voltage and amperage must be run for connection of the line cord,
or permanent connection to the unit.
The on/off switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or
cleaning the refrigerated area.
Under no circumstances is a self-contained unit to
be operated without the louvered panel in place.
Installation — Continued
Operation: Refrigerated Base Equipment Stands
Freezer base equipment stands are designed and pre-set at the
factory to maintain a temperature of 0°F to -5°F (-18°C to -21°C)
interior cabinet temperature at 100°F (38°C) ambient room
temperature. Self-contained units have a digital thermometer
installed in the removable louver. The digital thermometer for
remote units is located in the removable access panel.
Freezer Evaporator Fan Operation
The evaporator fan(s) and condenser fan will cycle off and on with
the compressor to conserve energy. The temperature control will
cycle the compressor and condenser fan motor and evaporator
fan motor to maintain box temperature at the control setting.
Cooling Cycle Defrost Cycle
Compressor On Compressor Off Compressor Off
Evap Fan
On
Evap Fan
Off
Evap Fan
On
Evap Fan
Off
Evap Fan
On
Evap Fan
Off
X X X
Freezer Defrost
Self-contained models use hot gas to defrost the evaporator coils.
Remote freezers use electric defrost.
Operation: Freezer Base Equipment Stands

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
8
Delfield
™
®
Maximum Cooking Equipment Weight Capacity
Model Total Weight Unit Weight Total Drawer Capacity Max Cooking Equipment
Weight
F2952C 1000lbs/ 454kg 398lbs/ 181kg 150lbs/ 68kg 452lbs/ 205kg
F2956C 1000lbs/ 454kg 405lbs/ 184kg 150lbs/ 68kg 445lbs/ 202kg
F2962C 1500lbs/ 680kg 479lbs/ 217kg 300lbs/ 136kg 721lbs/ 327kg
F2975C 1500lbs/ 680kg 540lbs/ 245kg 300lbs/ 136kg 660lbs/ 299kg
F2980C 1500lbs/ 680kg 578lbs/ 262kg 300lbs/ 136kg 622lbs/ 282kg
F2987C 1500lbs/ 680kg 672lbs/ 305kg 450lbs/ 204kg 378lbs/ 171kg
F2999C 1500lbs/ 680kg 691lbs/ 313kg 450lbs/ 204kg 359lbs/ 163kg
F29110C 1800lbs/ 816kg 766lbs/ 347kg 450lbs/ 204kg 584lbs/ 265kg
F2660C 1500lbs/ 680kg 418lbs/ 190kg 150lbs/ 68kg 932lbs/ 423kg
F2694C 1500lbs/ 680kg 500lbs/ 227kg 300lbs/ 136kg 700lbs/ 318kg
Temperature Control Settings, Self Contained Refrigerators And Freezers
A thermostat controls temperature in self contained
refrigerators and freezers. Thermostats are located in the
machine compartment. They are field adjustable and do not
require a service agent. The factory setting for refrigerators is
2.5. The factory setting for freezers is 4.5. Set toward 1 for
higher temperatures and toward 7 for lower temperatures.
Please make small incremental adjustments if
a temperature adjustment is necessary. Contact
the service department at Delfield +1 (989) 773-
7981 or your local service agent for additional
assistance. Delfield is not responsible for
charges incurred while adjusting the thermostat.
Temperature Control Settings, Remote Freezers
The temperature control is located in the machine
compartment. It is field adjustable and does not require a
service agent. The factory setting for a remote freezer is 0°F
cut-in with a 5°F differential.
Please make small incremental adjustments if
a temperature adjustment is necessary. Contact
the service department at Delfield +1 (989) 773-
7981 or your local service agent for additional
assistance. Delfield is not responsible for charges
incurred while adjusting the thermostat.

F2000/F17 Series Equipment Stand Service and Installation Manual
9
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
Maintenance
Door Gasket Maintenance
Door gaskets require regular cleaning to prevent mold and mildew
build up and also to retain the elasticity of the gasket. Gasket
cleaning can be done with the use of warm soapy water. Avoid
full strength cleaning products on gaskets as this can cause them
to become brittle and crack. Never use sharp tools or knives to
scrape or clean the gasket. Gaskets can be easily replaced and do
not require the use of tools or an authorized service person. The
gaskets are “Dart” style and can be pulled out of the groove in the
door and new gaskets can be “pressed” back into place.
Drain Maintenance - Base
Each unit has a drain located inside the unit that removes the
condensation from the evaporator coil and routes it to an external
condensate evaporator pan. Each drain can become loose or
disconnected during normal use. If you notice water accumulation
on the inside of the unit be sure the drain tube is connected to
the evaporator drain pan. If water is collecting underneath the unit
make sure the end of the drain tube is in the condensate evaporator
in the machine compartment. The leveling of the unit is important
as the units are designed to drain properly when level. Be sure all
drain lines are free of obstructions.
Drawer Maintenance
Drawer Assembly Cleaning
The drawer assembly is designed to be cleaned easily. Both drawer
and tracks are removable without tools. The drawer tracks are
dishwasher safe or can be cleaned in a sink with detergents and
a soft bristle brush. Drawers and tracks should be cleaned on a
weekly basis.
Remove Drawers
Pull the drawer box out until it stops. Lift up on the drawer front
and pull the drawer box completely out. Using a soft bristle brush,
clean the track on the bottom of the drawer box. When finished, it
should be wiped clean of all food and debris.
Tracks
The drawer box assembly must be removed. Pull the drawer tracks
out until they hit a stop. Locate blue safety clips towards the back
of each drawer track. Blue safety clips have a tab on the top. Push
the tab back until it clicks. Lift up and pull the drawer tracks all
the way out of the drawer
cage. The drawer tracks
are dishwasher safe or
can be cleaned in a sink
with detergents and a soft
bristle brush. Drawers
and tracks should be
cleaned on a weekly basis.
Using a soft bristle brush, wash the track making sure each roller
is thoroughly cleaned. The drawer cage should be cleaned with
a soft bristle brush, removing any food and debris gathered on
the bottom ledge. Once it’s cleaned thoroughly with a soft bristle
brush, wipe remaining debris clean with a soft towel.
Reassembly
Push the drawer tracks into the drawer cage. The blue safety clip
must remain pushed towards the back. Lift up and slide the drawer
track all the way into the drawer cage. The blue safety clip will
lock in place automatically. Once all tracks are replaced, insert the
drawer box. Rest the drawer box bottom track on the front track
roller. Then push the drawer back in place SLOWLY. When the
drawer box is about half way in you will hit a STOP. You must lift
the front of the drawer up approximately ½” (1.3cm) to continue
inward. Clean tracks as often as possible. The cleaner the tracks
are the better they will operate.
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or cleaning
the refrigerated area.
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and warm water.
If this isn’t sufficient, try ammonia and water or a nonabrasive
liquid cleaner. When cleaning the exterior, always rub with the
“grain” of the stainless steel to avoid marring the finish. Do not
use an abrasive cleaner because it will scratch the stainless steel
and can damage the breaker strips and gaskets.
Stainless Steel Care and Cleaning
To prevent discoloration or rust on stainless steel several important
steps need to be taken. First, we need to understand the properties
of stainless steel. Stainless steel contains 70- 80% iron, which will
rust. It also contains 12-30% chromium, which forms an invisible
passive film over the steel’s surface, which acts as a shield against
corrosion. As long as the protective layer is intact, the metal is still
stainless. If the film is broken or contaminated, outside elements
can begin to breakdown the steel and begin to form discoloration
or rust. Proper cleaning of stainless steel requires soft cloths or
plastic scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride
cleaners. Any cleaner containing chlorides will damage the
protective film of the stainless steel. Chlorides are also commonly
found in hard water, salts, and household and industrial cleaners. If
cleaners containing chlorides are used be sure to rinse repeatedly
and dry thoroughly. Routine cleaning of stainless steel can be done
with soap and water. Extreme stains or grease should be cleaned
with a non-abrasive cleaner and plastic scrub pad. Always rub with
the grain of the steel. There are stainless steel cleaners available
which can restore and preserve the finish of the steels protective
layer. Early signs of stainless steel breakdown are small pits and
cracks. If this has begun, clean thoroughly and start to apply
stainless steel cleaners in attempt to restore the passivity of the
steel.
tab on top of
blue safety clip

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
10
Delfield
™
®
Maintenance, continued
Never use an acid based cleaning solution! Many food
products have an acidic content, which can deteriorate
the finish. Be sure to clean the stainless steel surfaces
of ALL food products. Common items include,
tomatoes, peppers and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease regularly.
It is recommended that this be done at least every three months.
If conditions are such that the condenser is totally blocked in three
months, the frequency of cleaning should be increased. Clean the
condenser with a vacuum cleaner or stiff brush. If extremely dirty,
a commercially available condenser cleaner may be required.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation with
a dirty or clogged condenser coil can result in compressor failure.
Neglecting the condenser coil cleaning procedures will void any
warranties associated with the compressor and cost to replace the
compressor.
Never use a high-pressure water wash for this
cleaning procedure as water can damage the electrical
components located near or at the condenser coil.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic items,
such as pickles and tomatoes, in sealable containers. Immediately
wipe up all spills.
Units with pans should be operated with pans in place.
Operating the unit without all pans in place will lower
efficiency and may damage the unit.
Cleaning the condensate evaporator (remote models only)
The stainless steel condensate evaporator pan should be cleaned
every six months. Use a vacuum cleaner or damp cloth to remove
dust that may have accumulated. This will prevent corrosion of the
stainless steel.
Over shelves and other items mounted to the top of the counters
should never be installed in the field due to the potential damage
to the refrigeration system.

F2000/F17 Series Equipment Stand Service and Installation Manual
11
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
Wiring Diagram: F2900 & F17 Series Self Contained Refrigerators 115V/60HZ/1PH
Wiring Diagram: F2800 & F17 Series Remote Refrigerators 115V/60HZ/1PH
Note: Wiring for F2800 series includes junction box with 6" leads for field connection and wiring to evaporator fans and coils
only.

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
12
Delfield
™
®
Wiring Diagram: F2600 & F17 Series Self Contained Freezers
Wiring Diagram: F2700 & F17 Series Remote Freezers
Note: Wiring for F2700 series includes junction box with 6' leads for field connection and wiring to evaporator fans and coils
only.

F2000/F17 Series Equipment Stand Service and Installation Manual
13
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
F2600
Part# Description F2660 F2694
*000-BN5-0054 Assembly, 1/2 HP Cond, Low, HG X
*000-BN5-0055 Assembly, 3/4 HP Cond, Low, HG X
*000-AEW-007K Assembly, Drawer Sys, FRZ X X
*000-AMF-0033 Assembly, wall anchor, 18" louver X
*000-AMF-0034 Assembly, wall anchor, 24" louver X
*000-249-0004 Coil Assembly, Frz Evap, R404A X X
*000-298-003W Control Assembly, 5-20 X
*000-298-003V Control Assembly, 5-15 X
3234645 Leg, 6, S/S, Removable Foot X X
359-478-003J Panel, LVR Lo-Prole X
359-478-003K Panel, LVR Lo-Prole X
2190154 Switch, SPST, 15 Amp X
2194241 Switch, SPST, 20 Amp, Brown X
3516135 Thermometer, Hanging, 4” X X
2194791 Thermometer Cable, Danfoss X X
2194792 Thermometer Display, Digital,
Danfoss
X X
F2700
Part# Description F2748 F2776
*000-AMR-0030 Assembly, Condensate Evap Pan X X
*000-AEW-007K Assembly, Drawer Sys, FRZ X X
*000-AMF-0030 Assembly, wall anchor, lo pro X X
3516053 Coil, Solenoid, 120V/50Amp X X
*000-249-0006 Coil Assembly, Frz Evap, Remote X X
3516056 Control, Temperature X X
3234645 Leg, 6, S/S, Removable Foot X X
3516135 Thermometer, Hanging X X
2194791 Thermometer Cable, Danfoss X X
2194792 Thermometer Display, Digital,
Danfoss
X X
2194151 Timer, Paragon, #8145-00 X X
3516102 Valve, Solenoid, 1/4ODF X X
F2800 - All Models
Part# Description
*000-AMR-0030 Assembly, Condensate Evap Pan
243-209-0031 Clip, Coil Air Baffle, Left
243-209-0032 Clip, Coil Air Baffle, Right
3234645 Leg, 6, S/S, Removable Foot
3516135 Thermometer, Hanging, 4”
2194791 Thermometer Cable, Danfoss
2194792 Thermometer Display, Digital,
Danfoss
000-282-006T Thermostat Assembly, Danfoss
* Assembly and part prints on pages 17-21.
Replacement Parts - Listed by Model

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
14
Delfield
™
®
Part# Description F2852 F2856 F2862 F2875 F2880 F2887 F2899 F28110
*000-AMF-0031 Assembly, wall anchor, 14" louver X X
*000-AMF-0032 Assembly, wall anchor, 16" louver X X X
*000-AMF-0033 Assembly, wall anchor, 18" louver X X
*000-AMF-0030 Assembly, wall anchor, lo pro X
*000-248-0030 Coil Assembly, R404A, Ref X X X X X X X
*000-248-0037 Coil Assembly, R404A, Ref, Fan Lt X
*000-AEW-007F Drawer system, 19”, lo-prole X X X X
*000-AEW-007D Drawer system, 27”, lo-prole X X X X
*000-AEW-007C Drawer system, 32”, lo-prole X X X X
F2900 - All Models
Part# Description
3234160 Caster, 5, Plate, Swivel
3234161 Caster, 5, Plate, Swivel, Break
*000-298-003P Control Assembly, Refg, 5-15P
3516135 Thermometer, Hanging
2194791 Thermometer Cable, Danfoss
2194792 Thermometer Display, Digital,
Danfoss
Part# Description F2952C F2956C F2962C F2975C F2980C F2987C F2999C F29110C
030-209-0030 Angle, Coil, Top Baffle X X
*000-BN5-0037 Assembly, 1/3 HP Condensing Unit X
*000-BN5-0030 Assembly, 1/4 HP Condensing Unit X X X X
*000-BN5-0031 Assembly, 1/5 HP Condensing Unit X X X
*000-AMF-0031 Assembly, wall anchor, 14" louver X X X
*000-AMF-0032 Assembly, wall anchor, 16" louver X X X
*000-AMF-0033 Assembly, wall anchor, 18" louver X X
243-209-0031 Clip, Coil Air Baffle, Left X X X X X X X X
243-209-0032 Clip, Coil Air Baffle, Right X X X X X X
*000-248-0037 Coil Assembly, R404A, Ref, Fan Lt X X
*000-248-0030 Coil Assembly, R404A, Ref X X X X X X
*000-AEW-007F Drawer System, 19”, lo-prole X X
*000-AEW-007D Drawer system, 27”, lo-prole X X X
*000-AEW-007C Drawer system, 32”, lo-prole X X X X X
*359-478-003I Louver Panel, 14” X X X
*359-478-003L Louver Panel, 16” X X X
*359-478-003J Louver Panel, 18” X X X
F17OS
Part # Description
*000-405-0031 Bracket, cutting board, left hand
*000-405-0035 Bracket, cutting board, right hand
3234645 Leg, 6, S/S, Removable Foot
F17DD - All Models
Part # Description
*000-405-0031 Bracket, cutting board, left hand
*000-405-0035 Bracket, cutting board, right hand
* Assembly and part prints on pages 17-21.
Replacement Parts - Listed by Model

F2000/F17 Series Equipment Stand Service and Installation Manual
15
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
F17C - All Models
Part # Description
*000-AMF-0031 Assembly, 14 RT Wall Anchor
*000-405-0031 Bracket, cutting board, left hand
*000-405-0035 Bracket, cutting board, right hand
*000-298-003P Control Assembly, Refg, 5-15P
3234645 Leg, 6, S/S, Removable Foot
2194099 Switch, SPST, 15 Amp
2194791 Thermometer Cable, Danfoss
2194792 Thermometer Display, Digital,
Danfoss
Part # Description F17C52 F17C60 F17C68 F17C78 F17C87 F17C95 F17C110
030-209-0030 Angle, Coil, Top Baffle X
*000-BN5-0037 Assembly, 1/3 HP Condensing Unit X
*000-BN5-0030 Assembly, 1/4 HP Condensing Unit X X X
*000-BN5-0031 Assembly, 1/5 HP Condensing Unit X X X
*000-AEW-0066 Assembly, drawer, 19” lo prole X X
*000-AEW-0064 Assembly, drawer, 27” lo prole X X X X
*000-AEW-0063 Assembly, drawer, 32” lo prole X X X
243-209-0031 Clip, Coil Air Baffle, Left X X X X X X X
243-209-0032 Clip, Coil Air Baffle, Right X X X X X X
*000-248-0037 Coil Assembly, R404A, Ref, Fan Lt X
*000-248-0030 Coil Assembly, R404A, Ref X X X X X X
F17R - All Models
Part # Description
*000-AMR-0030 Assy., Condensate Evap Pan
*000-405-0031 Bracket, cutting board, left hand
*000-405-0035 Bracket, cutting board, right hand
3234645 Leg, 6, S/S, Removable Foot
000-282-006T Thermostat Assembly, Danfoss
2194791 Thermometer Cable, Danfoss
2194792 Thermometer Display, Digital,
Danfoss
Part # Description F17R44 F17R52 F17R60 F17R70 F17R79 F17R87 F17R102
030-209-0030 Angle, Coil, Top Baffle X
*000-AEW-0033 Assembly, drawer, 19” lo prole X X
*000-AEW-0031 Assembly, drawer 27” lo prole X X X X
*000-AEW-0063 Assembly, drawer, 32” lo prole X X X
243-209-0031 Clip, Coil Air Baffle, Left X X X X X X
243-209-0032 Clip, Coil Air Baffle, Right X X X X X
*000-248-0037 Coil Assembly, R404A, Ref, Fan Lt X
*000-248-0030 Coil Assembly, R404A, Ref X X X X X X
* Assembly and part prints on pages 17-21.
Replacement Parts - Listed by Model

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
16
Delfield
™
®
F17FC - All Models
Part # Description
*000-405-0031 Bracket, cutting board, left hand
*000-405-0035 Bracket, cutting board, right hand
*000-249-0004 Coil Assembly, Frz Evap, R404A
3234645 Leg, 6, S/S, Removable Foot
3516135 Thermometer, Hanging, 4”
2194791 Thermometer Cable, Danfoss
2194792 Thermometer Display, Digital, Danfoss
Part # Description F17FC60 F17FC76 F17FC84 F17FC94
*000-BN5-0054 Assembly, 1/2HP Condenser, Low X
*000-BN5-0055 Assembly, 3/4 HP Condenser, Low X X X
*000-AEW-006J Assembly, drawer, 19” freezer, lo-prole X
*000-AEW-006M Assembly, drawer, 27” freezer, lo-prole X X
*000-AEW-006G Assembly, drawer, 32” freezer, lo-prole X X
*000-298-003W Control Assembly, 5-20 XXX
*000-298-003V Control Assembly, 5-15 X
356-478-0031 Panel, louver, 18” X
356-478-0032 Panel, louver, 24” X X X
2190154 Switch, SPST, 15 Amp, 120V X X X X
2194241 Switch, SPST, 20 Amp, Brown X X X
F17FR - All Models
Part # Description
*000-AMR-0030 Assembly, Condensate Evap Pan
*000-405-0031 Bracket, cutting board, left hand
*000-405-0035 Bracket, cutting board, right hand
*000-249-0006 Coil Assembly, Frz Evap, Remote
3516056 Control, Temperature
3234645 Leg, 6, S/S, Removable Foot
2194791 Thermometer Cable, Danfoss
2194792 Thermometer Display, Digital, Danfoss
2194151 Timer, Paragon, #8145-00
Part # Description F17FR48 F17FR58 F17FR66 F17FR76
*000-AEW-003D Assembly, drawer, 19” freezer, lo-prole X
*000-AEW-003B Assembly, drawer, 27” freezer, lo-prole X X
*000-AEW-003A Assembly, drawer, 32” freezer, lo-prole X X
* Assembly and part prints on pages 17-21.
Replacement Parts - Listed by Model

F2000/F17 Series Equipment Stand Service and Installation Manual
17
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
1
2
4
56
7
8
9
3
Key Part Number Description
-000-BN5-0030 Assembly, 1/4 HP Condensing Unit
13516457 Blade, Fan, 7.25 DIA., 30Deg
22160020 Guard, Fan, 7.25
32162717 Motor, Fan, 9W, 115V, CW
43526999 Compressor, NF5.5CLX, 115V, 60HZ
52194787 Capacitor, Start, 280MFD
63516444 Compressor, Relay, Overload, NF5.5CLX
73516322 Drier, Filter, (2)Inlet
8039-231-0030 Pan, Condensate, SM
93516454 Coil, Condenser, 1/5, 1/4,1/3HP
Key Part Number Description
- 000-BN5-0054 Assembly, 1/2HP Cond, Low, Hot gas
13516554 Blade, Fan, 9.00”
22160019 Guard, Fan, Wire
32162716 Motor, Fan, 16W, 115V, CW
43516324 Cutout, High Pressure
53527001 Compressor, SC12CLX.2,115/60HZ
63516322 Drier, Filter, (2)Inlet
72194789 Capacitor, Start, 240MFD
83516441 Relay, Comp, SC12CLX.2
93516455 Coil, Condenser, 1/2 HP
- 024-034-0031 Pan, Comp, 18.00
1
2
4
56
7
8
9
3
Key Part Number Description
- 000-BN5-0055 Assembly, 3/4 HP Cond, Low, Hot gas
12160019 Guard, fan condenser
2162716 Motor, condenser fan 16W, 155V
3516433 Blade, fan 10” CW
23527002 Compressor, SC18CLS.2, 115V60hz
3516442 Capacitor, start, run assembly
33516322 Filter drier
43516456 Coil, condenser, 3/4hp
Key Part Number Description
000-BN5-0031 Assembly, 1/5 Condensing Unit
13516457 Blade, Fan, 7.25 DIA.,30 Deg
22160020 Guard, Fan, 7.25
32162717 Motor, Fan, 9W, 115V, CW
43526997 Compressor, 1/5HP, 115/60, R404A
52194787 Capacitor, Start, 280MFD
63516446 Compressor, Relay, Danfoss
73516322 Drier, Filter, (2)Inlet
8039-231-0030 Pan, Condensate, SM
93516454 Coil, Condenser, 1/5, 1/4, 1/3HP
12
3
4
Replacement Parts - Condensing Unit Asemblies
3
2
4
5
8
7
6
1
9

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
18
Delfield
™
®
Replacement Parts - Condensing Unit Assemblies
123
4
5
6
7
8
Key Part Number Description
-000-BN5-0037 Assembly, 1/3 Condensing Unit
13516457 Fan Blade
22160020 Fan Guard
33527000 Compress, Danfoss, NF7CLS
42194788 Start Capacitor
53516322 Filter Drier
6 075-231-0030 Pan, Condensate
72162717 Fan Motor
83516454 Condenser Coil
-3516438 Relay, overload, compressor

F2000/F17 Series Equipment Stand Service and Installation Manual
19
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
Delfield
™
®
Key Part Number Description
- 000-249-0004 Coil Assembly, Evap, Freezer
1 030-262-0001 Side, evaporator
22160023 Fan, axiel
32160024 Guard, fan, 4.7", SC120-W2
4 030-260-0001 Top, frz, evaporator
5 030-259-0000 Front, enclosure
63516271 Valve, expansion, R404a
7 265-261-0001 Pan, freezer evaporator
83516073 Coil, Evaporator
9 030-263-0001 Back, evaporator
- 2184318 Harness, coil, frz, male
-2194808 Probe, Defrost, Danfoss, Control
-2194809 Probe, Temp, Sensor, Danfoss
3
2
5
7
9
6
4
1
8
Key Part Number Description
-000-248-0030 Coil Assembly, R404A, Ref
12160024 Guard, fan, 4.7"
22160023 Fan, axiel, 120V
33516095 Coil, evaporator
4 030-232-0003 Back, evaporator, enclosure
53516273 Expansion valve, 1/4, R-404a
6 030-233-0001 Side, coil, angled
7 075-231-0033 Drip pan, evaporator
8 030-234-0003 Front, coil
-2184317 Harness, coil
-2194808 Probe, Defrost, Danfoss, Control
-2194809 Probe, Temp, Sensor, Danfoss
12
3
4
5
6
7
8
Key Part Number Description
- 000-249-0006 Coil Assembly, Freezer Evap, Remote
1 030-262-0001 Side, evaporator
22160023 Fan, axiel
32160024 Guard, fan, 4.7", SC120-W2
4 030-260-0001 Top, frz, evaporator
5 030-259-0000 Front, enclosure
63516271 Valve, expansion, R404a
73516073 Coil, Evaporator
82194034 Heater, Defrost
9 265-261-0001 Pan, freezer evaporator
10 030-263-0001 Back, evaporator
-2194046 Control, Limit, Fan Delay/Defrost
-2194631 Fuse, Defrost Heater, 7 Amp
- 2184323 Harness, coil, frz, male, remote
3
25
9
10
6
4
1
8
7
Replacement Parts - Evaporator Coil Assemblies
1
2
3
4
7
6
5
8
9
Key Part Number Description
- 000-248-0037 Coil Assembly, R404A, Ref, Fan Lt
12160024 Guard, fan, 4.7"
22160023 Fan, axiel, 120V
33516095 Coil, evaporator
4 030-232-0003 Back, evaporator, enclosure
5000-BNH-0030 Drip pan, evaporator
6 030-233-0038 Side, coil, angled, Rt, Blank
73516273 Expansion valve, 1/4, R-404a
8 030-234-0003 Front, coil
9 030-233-0039 Side, Coil, Angled, Lt, 2Fan
-2184317 Harness, coil
-2194808 Probe, Defrost, Danfoss, Control
-2194809 Probe, Temp, Sensor, Danfoss

F2000/F17 Series Equipment Stand Service and Installation Manual
For customer service, call [phone], [phone], Fax [phone], www.delfield.com
20
Delfield
™
®
Key Part Number Description
-000-AEW-0063 Assembly, drawer, 32” lo prole
1000-328-0033 Front, drawer, 32” lo prole
21701197 Gasket, drawer, 32” lo prole
3000-315-0033 Mullion, refrigerator, 32" drawer
4000-333-0043 Assembly, drawer box, 32”
-3234925 Interm prole, LH (with nylon rollers)
-3234926 Interm prole, RH (with nylon rollers)
-000-AEW-0064 Assembly, drawer 27” lo prole
1000-328-0032 Front, drawer 27” lo prole
21701196 Gasket, drawer 27” lo prole
3000-315-0032 Mullion, refrigerator, 27" drawer
4000-333-0044 Assembly, drawer box, 27” lo prole
-3234925 Interm prole, LH (with nylon rollers)
-3234926 Interm prole, RH (with nylon rollers)
-000-AEW-0066 Assembly, drawer, 19” lo prole
1000-328-0030 Front, drawer, 19”
21701194 Gasket, drawer 19” lo prole
3 000-315-0030 Mullion, refrigerator, 19" drawer
4 000-333-0046 Assembly, drawer box, 19”
-3234925 Interm prole, LH (with nylon rollers)
-3234926 Interm prole, RH (with nylon rollers)
- 000-AEW-006G Assembly, drawer, 32” freezer, lo prole
1000-328-0033 Front, drawer, 32” lo prole
21701197 Gasket, drawer, 32” lo prole
3 000-315-003B Mullion, Freezer, 32" Drawer
4000-333-0043 Assembly, drawer box, 32”
-3234925 Interm prole, LH (with nylon rollers)
-3234926 Interm prole, RH (with nylon rollers)
-000-AEW-006H Assembly, drawer, 27” freezer, lo prole
1000-328-0032 Front, drawer 27” lo prole
21701196 Gasket, drawer 27” lo prole
3 000-315-003A Mullion, Freezer, 27" Drawer
4000-333-0044 Assembly, drawer box, 27” lo prole
-3234925 Interm prole, LH (with nylon rollers)
-3234926 Interm prole, RH (with nylon rollers)
Key Part Number Description
-000-AEW-006J Assembly, drawer, 19” freezer, lo prole
1000-328-0030 Front, drawer, 19”
21701194 Gasket, drawer 19” lo prole
3 000-315-0038 Mullion, Freezer, 19" Drawer
4 000-333-0046 Assembly, drawer box, 19”
-3234925 Interm prole, LH (with nylon rollers)
-3234926 Interm prole, RH (with nylon rollers)
-000-AEW-007C Drawer system, 32”, lo-prole
1000-328-003J Drawer front, 32”
21701197 Gasket, drawer, 32”
3000-315-0033 Mullion, refrigerator, 32" drawer
4000-333-0043 Drawer box, 32”
-3234925 Track, interm, left hand
-3234926 Track, interm, right hand
-000-AEW-007D Drawer system, 27”, lo-prole
1000-328-003I Drawer front, 27”
21701196 Gasket, drawer, 27”
3000-315-0032 Mullion, refrigerator, 27" drawer
4000-333-0044 Drawer box, 27”
-3234925 Track, interm, left hand
-3234926 Track, interm, right hand
- 000-AEW-007F Drawer system, 19”, lo-prole
1000-328-003G Drawer front, 19”
21701194 Gasket, drawer, 19”
3 000-315-0030 Mullion, refrigerator, 19" drawer
4 000-333-0046 Drawer box, 19”
-3234925 Track, interm, left hand
-3234926 Track, interm, right hand
- 000-AEW-
007K
Assembly, Drawer Sys, FRZ
1000-328-003J Front, 32 Drawer FRZ 3-HI
21701195 Gasket, Drawer, 24, 2-High, Lo
3 000-315-003B Mullion, Freezer, 32" Drawer
4000-333-0043 Assembly, Drawer Box, 32”
-3234925 Interm Prole, LH, Reg
-3234926 Interm Prole, RH, Reg
1
2
4
3
Replacement Parts - Drawer Assemblies