Long Form Specifications
Top is constructed of 18-gauge stainless steel, with integral front
marine edge nosing and rear backsplash. Spline bars made of 12-
gauge stainless steel and run front to back on both the left and right
stainless steel sides for support and spline purposes. Interior sub-
top made of 22 gauge 2BF stainless steel is made integral with the
top by injecting 2.00” of high density polyurethane foam between
the exterior and interior tops. As a standard, 14-gauge cutting board
brackets are attached to each side and house a 1.25” thick x 9.5”
deep maple cutting board.
Refrigerated base interior back and bottom is constructed of
22-gauge 2BF stainless steel. Exterior sides are constructed of
18-gauge stainless steel. Bottom and back are made of 22 gauge
galvanized steel. Both left and right interior sides are formed of ABS
plastic. The base is injected with 2.00” of high density polyurethane
foam between the exterior and interior. Refrigerated base fronts
are made of .095” thick ABS thermoformed plastic and backed up
by ridged polyurethane water blown injection molded frames. The
frames are an excellent thermo-break and superior structural material
for fastening doors and drawers. Exterior machine compartment
side is constructed of 18-gauge galvanized steel.
Single units are supplied with wall-mounted bracket and threaded
rod to allow installation of the unit against a solid surface. Units
shipped, as part of a line-up do not come standard with a wall
mounted bracket assembly.
Full Extension Plus drawer system is a complete drawer system,
which can operate independent of the unit it’s installed in. Drawer
system is sized to hold 12 x 20 x 4 “ deep hotel pans and smaller
fractional pans. Drawer system is all stainless steel construction
for maximum durability. Outer drawer track is made of 11-gauge
stainless and held in place with 12-gauge up-right and cross
supports. Drawer track rollers are made of Delrin™ 100 NC-10
and do not require grease for operation. Intermediate tracks are
removable without tools and house Delfield’s “anti-friction binary
roller system”. Drawer boxes are designed with “easy pan grip
flanges”. Tracks are designed with a stay shut feature that holds
the drawer gasket tight to the base front on uneven floors. Exterior
drawer fronts are made of 22- gauge stainless steel; and an interior
made of ABS plastic with formed in channels to house the snap-in
dart style santoprene gasket. A 12-gauge galvanized brace is foamed
in place to be an integral part of the drawer front assembly. Each
drawer front is injected with 1.87” of high density polyurethane foam
between the exterior and interior. Handles are recessed black plastic
and held in with a positive lock system.
Model F17C68
Self-Contained Refrigerated Base Equipment Stands
The Delfield Company, 980 S. Isabella Rd., Mt Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2003 The Delfield Company. All rights reserved. Printed in U.S.A.
PROJECT
ITEM #
QUANTITY DATE
APPROVAL
F17C
Unit is supported with two 14-gauge leg rails that run the entire
length of the unit. Leg rails are welded to the bottom side of the unit
and are tied together with two 12-gauge braces running front to back.
Caster/leg boxes are welded inside the leg rail and 6.12” adjustable
stainless steel legs are mounted as standard with (4) 5/16” bolts.
Self-contained models have a pre-wired condensing unit and a digital
thermometer installed in the machine compartments (standard on
right) louver panel and supplied with an 8’ cord and plug. Interior
refrigerated base cabinet will maintain 36 to 40 degree temperatures
at 100-degree ambient room temperature.
Refrigeration system components are HFC-404A. Interior cabinet
is cooled with mullion style blower coils (coated) mounted between
each door/drawer section for even air and temperature control.
Electrical connections are 115V-60H-1PH.
Optional Accessories and Modifications
505B Stainless steel back
906A Stainless steel end
505F Laminate facing (drawers only)
905A Laminate back
906E Laminate end
1027A Casters
104 Doors, except 32"
108 Locks
213 *220V/50 cycle electrical
* Inclusion of this option will alter electrical specifications.
