Dell EMC LTO8 User manual

A Dell EMC document category
Dell EMC Tape Systems
LTO Media Handbook
Dell Engineering
April 2018

2 Dell EMC Tape Systems | Document ID | version (optional)
Revisions
Date
Description
October 2015
Initial release
April 2018
New Dell EMC format.
The information in this publication is provided “as is.” Dell Inc. makes no representations or warranties of any kind with respect to the information in this
publication, and specifically disclaims implied warranties of merchantability or fitness for a particular purpose.
Use, copying, and distribution of any software described in this publication requires an applicable software license.
Copyright © April 2018 Dell Inc. or its subsidiaries. All Rights Reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Other trademarks may be the property of their respective owners. Published in the USA [4/10/2018] [document category] [Document ID]
Dell believes the information in this document is accurate as of its publication date. The information is subject to change without notice.

3 Dell EMC Tape Systems | Document ID | version (optional)
Table of contents
Revisions.............................................................................................................................................................................2
1Introduction...................................................................................................................................................................4
2Drives ...........................................................................................................................................................................5
3Media............................................................................................................................................................................6
4Media colors and markings ..........................................................................................................................................7
5Media Compatibility......................................................................................................................................................9
6Cleaning cartridges ....................................................................................................................................................10
6.1 Usage ...............................................................................................................................................................10
7WORM cartridges.......................................................................................................................................................12
8Write Protection..........................................................................................................................................................13
9Cartridge Memory.......................................................................................................................................................14
10 Barcodes ....................................................................................................................................................................15
11 Media Handling...........................................................................................................................................................16
11.1 Media Description.............................................................................................................................................16
11.2 Inspection .........................................................................................................................................................16
11.3 Handle the Cartridge Carefully.........................................................................................................................17
11.4 Ensure Proper Packaging While Shipping .......................................................................................................19
11.5 Cartridge Storage Conditions...........................................................................................................................19
11.6 Cartridge Life....................................................................................................................................................20
12 LTO7 Type M media...................................................................................................................................................21
12.1 Using LTO7 Type M media in Dell EMC tape libraries.....................................................................................21
12.2 Using LTO7 Type M media in Dell EMC tape drives........................................................................................21
12.3 Formatting an LTO7 Type M tape in a Dell EMC library..................................................................................21
13 Troubleshooting & Best Practices..............................................................................................................................22
13.1 Stuck tape.........................................................................................................................................................22
13.1.1 Drive reset....................................................................................................................................................22
13.2 Media Do’s and Don’ts .....................................................................................................................................22
13.2.1 Do’s ..............................................................................................................................................................22
13.2.2 Don’ts ...........................................................................................................................................................22

4 Dell EMC Tape Systems | Document ID | version (optional)
1 Introduction
This document describes media compatibility, handling and usage for all Dell EMC and Dell PowerVault
Linear Tape Open (LTO) drives.

5 Dell EMC Tape Systems | Document ID | version (optional)
2 Drives
Dell EMC LTO tape drives are available in several form factors that can be attached internally and externally
to PowerEdge servers or as part of a Dell EMC tape library solution.
Current LTO drive specifications
Historical LTO drive specifications

6 Dell EMC Tape Systems | Document ID | version (optional)
3 Media
Media comes in both standard Data and WORM (Write Once Read Many) formats for each generation of LTO
and is differentiated by color to be easily recognizable. Cleaning cartridges are universal to all LTO
generations. Table 3 shows recording information about each media type.
Data capacity and recording formats

7 Dell EMC Tape Systems | Document ID | version (optional)
4 Media colors and markings
Media types are color coded to be easily identified in the data center. Color coding is not an industry standard
and varies by distributers. Standard data cartridges are a single solid color. WORM cartridges are
differentiated with a grey back cover and the generational color on the front cover. All genuine LTO media will
have the Ultrium LTO logo and generation markings on the cartridge.
Dell EMC historical and current LTO generation cartridge colors
The Ultrium LTO logo is displayed along with the generation number on both the outer cartridge carrier and
the physical media cartridge in the lower left corner. Data capacity information is also provided on Dell EMC
media.
Media markings

8 Dell EMC Tape Systems | Document ID | version (optional)
WORM cartridges use the same generation color coding for the front or top of the cartridge but have a grey
back or bottom cover to visually differentiate.
WORM and standard Data cartridge

9 Dell EMC Tape Systems | Document ID | version (optional)
5 Media Compatibility
Each new LTO generation aims to achieve the highest bit density possible utilizing the latest technology.
Higher bit densities allow more data to be stored on the magnetic medium within the same form factor. These
constant improvements to the technology results in a backwards Read/Write compatibility limitation as new
generations are brought to the market. Table 4 demonstrates each generation’s capabilities.
Tape drive and cartridge compatibility

10 Dell EMC Tape Systems | Document ID | version (optional)
6 Cleaning cartridges
Universal Cleaning Cartridges (UCC) are designed to be used with all LTO generations. The color of the Dell
EMC UCC is Black. Certified cleaning media will contain the LTO Ultrium logo in the lower left corner and will
have a Universal Cleaning Cartridge designation printed on the front. Other artwork may vary.
Cleaning cartridges that were manufactured prior to the release of a newer generation LTO drive may not
contain the correct drive generation information printed on the front of the cartridge, this does not limit that
media from being universally accepted in the newer generation LTO drives. All LTO generations to date use
the same UCC cartridge.
Each UCC is capable of performing 50 cleaning routines.
6.1 Usage
LTO drives have built in algorithms to determine when the tape heads need to be cleaned. It is always best to
allow the drive to determine when a cleaning is required. Excessive cleaning of the tape heads will degrade
head performance. The drive will alert the user when a cleaning is required. There are two main criteria used
by the drive to call for cleaning:
• Clean required (also known as Clean Now TapeAlert 14h)
Clean required is triggered when the drive posts specific permanent errors or is running
degraded. It is not based on temporary or permanent error rates. The permanent errors are
typically read/write perms or servo related perm failures. Not all read/write or servo perms will
trigger a clean. The errors are typically sticky, which means that the drive may not allow data
operations unless a clean is performed, even if a power cycle occurs.
• Clean Requested (also known as Clean Periodic TapeAlert 15)
Clean Requested is based on usage, but not media motion hours. Two criteria are used, Data
sets processed or Meters of tape pulled across the head.
LTO drives will post a “C” on the Single Character Display (SCD) and send the tape alert information to the
host application and library, if the drive is part of an automated solution. If another cartridge is inserted after a
clean is requested, the drive continues to operate however the ‘C’ on the SCD of the drive persists until the
drive is cleaned or power cycled. If the drive is power cycled, the ‘C’ will reappear on the SCD until the drive is
cleaned. Libraries can be setup to automatically perform the clean operation without user interaction; check
library Users Guide for more detailed information.
Once the UCC is inserted, the drive will determine if cartridge has cleaning cycles remaining. If the tape is
valid the cleaning routine will start automatically. During the cleaning routine the drive activity light will blink
green and the SCD will display “C”. When complete the drive will increment the clean count by one for that
cartridge and eject. The drive will post a tape alert to the host application and library interface indicating a
successful clean.

11 Dell EMC Tape Systems | Document ID | version (optional)
If an expired UCC is inserted into an LTO drive the drive will alert the user by posting a “7” and flash the
activity light amber. A tape alert message is generated. The clean routine will not be run and a new UCC will
be required.

12 Dell EMC Tape Systems | Document ID | version (optional)
7 WORM cartridges
WORM stands for Write Once, Read Many. This means once data is written to a piece of WORM media, the
data on the tape cannot be changed or overwritten. WORM media can be appended to if data is already
present on the tape. The media also stores unique identifiers which allow the drive to determine whether or
not the media has been tampered with.
WORM media offers a method of data retention for compliance laws such as the Sarbanes-Oxley Act of 2002.
WORM media

13 Dell EMC Tape Systems | Document ID | version (optional)
8 Write Protection
To preserve data on the cartridge from being overwritten or erased use the Write Protect tab. The tab must be
engaged prior to inserting the media into the drive. Do not slide the tab while media is already inserted in a
drive.
When properly write protected a lock symbol will be visible on the red tab of the cartridge and the SCD on the
drive will display the character “P” when cartridge is inserted. If the drive does not display the character “P”
eject the cartridge and inspect the slide tab to insure it is properly closed (locked) and reinsert.
Write Protect Tab

14 Dell EMC Tape Systems | Document ID | version (optional)
9 Cartridge Memory
Tape drives require information about the tape cartridge being used. For LTO tape cartridges, this information
is stored in a small chip within the tape and is referred to as the Cartridge Memory (CM). CM is a nonvolatile
memory that responds through a passive radio frequency interface.
The CM holds the following information:
• The type of cartridge
• Important information that the drive uses to setup and calibrate
• The tape directory to enable a quick search for data sets
You experience difficulties with the cartridge if the CM is damaged or corrupted. However, the user data can
still be recovered. To recover the data, set the write protect tab on the cartridge and the load the cartridge into
an Ultrium drive.
The drive stores enough information on tape to be able to recognize the tape. However, the data directory is
lost. Hence, the drive can only search from the beginning of tape (BOT) to end of tape (EOT) across all wraps
to find the data. A Fast Search to the correct location is not possible.

15 Dell EMC Tape Systems | Document ID | version (optional)
10 Barcodes
A bar code label contains:
A volume serial number (VOLSER) that is human-readable
A bar code that the library can read
When read by a library's bar code reader, the bar code identifies the cartridge's VOLSER to the library. The
bar code also tells the library whether the cartridge is a data cartridge or cleaning cartridge. In addition, the
bar code includes the two-character media-type identifier Lx, where x equals 1-8. L identifies the cartridge as
an LTO cartridge and the number represents the generation of cartridge for that cartridge type.
Barcode label and Media Identifier.
Dell EMC cleaning media barcodes will have a VOLSER of CLN for the first three characters and the media
identifier will be either L1 or CU.

16 Dell EMC Tape Systems | Document ID | version (optional)
11 Media Handling
11.1 Media Description
LTO Ultrium Data Cartridge
1. LTO CM
2. label area
3. write-protect switch
4. insertion guide
5. cartridge door
6. leader pin
11.2 Inspection
Inspect the cartridge packaging to check for any rough handling.
• When inspecting a cartridge, open only the cartridge door. Do not open any other part of the cartridge case.
The upper and lower parts of the case are held together with screws; separating them destroys the
usefulness of the cartridge. While the door is open, check that the leader pin is properly seated. If the
cartridge has been dropped, it is likely that the pin is dislodged inside the cartridge. It is recommended that
you open the door and check if the pin is properly seated before each use.

17 Dell EMC Tape Systems | Document ID | version (optional)
Correct Leader pin location
• Inspect the cartridge for damage before using or storing it.
• Inspect the back of the cartridge (the part that you load first into the tape load compartment) and ensure that
there are no gaps in the seam of the cartridge case. If there are gaps in the seam, the leader pin may be
dislodged. See Figure 6.
• If you suspect that the cartridge has been mishandled but it appears usable, copy any data onto a good
cartridge immediately for possible data recovery. Discard the mishandled cartridge.
11.3 Handle the Cartridge Carefully
Do not drop the cartridge. If the cartridge drops, slide the cartridge door back and ensure that the leader pin is
properly seated in the pin-retaining spring clips. See Figure 6.
• Do not handle tape that is outside the cartridge. Handling the tape can damage the tape surface or
edges, which may interfere with the read or write reliability. Pulling on tape that is outside the cartridge
can damage the tape and the brake mechanism in the cartridge.
• Do not stack more than six cartridges.
• Do not degauss a cartridge that you intend to reuse. Degaussing renders the tape unusable.
Figure 7 displays a dropped tape which resulted in a dislodged leader pin. This cartridge if inserted into a
drive could result in a stuck tape. Other damage could result in the leader pin falling out of the cartridge or
getting dropped inside the tape housing.

18 Dell EMC Tape Systems | Document ID | version (optional)
Dropped leader pin
Figure 8 shows an LTO cartridge that was dropped and caused damage to the casing.
Split seam on case.

19 Dell EMC Tape Systems | Document ID | version (optional)
11.4 Ensure Proper Packaging While Shipping
When you ship a cartridge, ship it in its original or better packaging.
Always ship or store a cartridge in the vertical orientation and inside the jewel case to prevent damage to
the tape edge.
Use only a recommended shipping container that securely holds the cartridge in its jewel case during
transportation.
Never ship a cartridge in a commercial shipping envelope. Always place it in a box or package.
If you ship the cartridge in a cardboard box or a box of a sturdy material, ensure the following:
Place the cartridge in polyethylene plastic wrap or bags to protect it from dust, moisture, and other
contaminants.
Pack the cartridge snugly. Do not allow it to move around.
Double-box the cartridge (place it inside a box, then place that box inside the shipping box) and add
padding between the two boxes.
11.5 Cartridge Storage Conditions
Before you use a cartridge, let it acclimate to the normal operating environment for 24 hours.
Ensure that all surfaces of the cartridge are dry before use.
Do not expose the cartridge to moisture or direct sunlight.
Always ship or store a cartridge in the vertical orientation and inside a jewel case to prevent damage to
the tape edge.
Do not expose recorded or blank cartridges to stray magnetic fields (for example, terminals, motors, video
equipment, X-ray equipment, or fields that exist near high-current cables or power supplies). Such
exposure can lead to loss of data or render the blank cartridge unusable.
Maintain the environmental conditions outlined in the Table 5.
Storage conditions

20 Dell EMC Tape Systems | Document ID | version (optional)
11.6 Cartridge Life
Durability –1,000,000 passes on any area of tape, equates to over 20,000 end-to-end passes/260 full
tape backups.
Archival life –30 years.