Dell POWEREDGE RAID H700 Quick start guide

Dell PowerEdge RAID
Controller Cards
H700 and H800
Technical Guide
Enterprise-class
controllers
designed for
performance,
reliability, and
fault tolerance.

Dell
DELL PERC H700 and H800 Technical Guide 2
This document is for informational purposes only. Dell reserves the right to make changes without
further notice to any products herein. The content provided is as is and without express or implied
warranties of any kind.
Dell, PowerEdge, PowerVault, and OpenManage are trademarks of Dell, Inc. Microsoft and Windows
are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or
other countries. Red Hat is a registered trademark of Red Hat, Inc. in the United States and other
countries. Linux is a registered trademark of Linus Torvalds. Other trademarks and trade names may
be used in this document to refer to either the entities claiming the marks and names or their
products. Dell disclaims proprietary interest in the marks and names of others.
©Copyright 2009–2011 Dell Inc. All rights reserved. Reproduction or translation of any part of this
work beyond that permitted by U.S. copyright laws without the written permission of Dell Inc. is
unlawful and strictly forbidden.
Revision 3 March 2011

Dell
DELL PERC H700 and H800 Technical Guide 3
Table of Contents
1Product Comparison ...........................................................................................5
1.1 Overview ..................................................................................................5
1.2 PERC H700 Model Overview.............................................................................6
1.3 PERC H800 Model Overview.............................................................................7
2New Features ...................................................................................................9
2.1 New Feature Overview ..................................................................................9
2.2 6Gb/s SAS (SAS 2.0) Overview..........................................................................9
2.2.1 6Gb/s SAS Performance Benefit over 3Gb/s SAS ............................................ 10
2.2.2 6Gb/s SAS Expectation .......................................................................... 10
3Product Support .............................................................................................. 11
3.1 PowerEdge™ Server Support .......................................................................... 11
3.2 Management Software Support....................................................................... 11
3.3 Operating System Support ............................................................................ 11
3.4 Drive Support ........................................................................................... 12
4Product Overview ............................................................................................ 13
4.1 PERC H700 and PERC H800 Feature Overview ..................................................... 13
4.2 CacheCade .............................................................................................. 15
4.3 Cut-Through IO ......................................................................................... 15
4.4 Reconfiguring Virtual Disks ........................................................................... 15
4.5 Fault-Tolerance Features ............................................................................. 16
4.5.1 Non-Volatile Cache............................................................................... 17
4.5.2 Automatic Replace Member with Predicted Failure......................................... 17
4.5.3 Redundant Path with Load Balancing Support ............................................... 17
4.5.4 Failed Physical Disk Detection ................................................................. 17
4.5.5 Using Replace Member and Revertible Hot Spares .......................................... 17
4.5.6 Enclosure Affinity ................................................................................ 18
4.5.7 Battery Back-up of Controller Cache .......................................................... 18
4.6 Physical Disk Hot Swapping ........................................................................... 18
4.7 Disk Roaming............................................................................................ 19
4.8 Disk Migration........................................................................................... 19
4.9 PERC H700 and H800 Security Key and RAID Management ....................................... 19
4.9.1 PERC H700 and H800 Security Key Implementation ......................................... 19
4.9.2 Configuring and Managing Secured RAID ...................................................... 19
4.10 Virtual Disk Write Cache Policies .................................................................... 20
4.11 Virtual Disk Read Cache Policies..................................................................... 20
5RAID Overview................................................................................................ 21
5.1 About RAID .............................................................................................. 21
5.2 Advantages of RAID .................................................................................... 21
5.3 Supported RAID Levels................................................................................. 21
5.3.1 RAID 0 (Striped Virtual Disk without Fault Tolerance)...................................... 21
5.3.2 RAID 1 (Mirroring) ................................................................................ 22
5.3.3 RAID 5 (Striping With Distributed Parity) ..................................................... 23
5.3.4 RAID 6 (Striping With Dual Distributed Parity) ............................................... 24

Dell
DELL PERC H700 and H800 Technical Guide 4
5.3.5 RAID 10 (Striping over Mirrored Sets) ......................................................... 25
5.3.6 RAID 50 (Striping Across RAID 5) ............................................................... 26
5.3.7 RAID 60 (Striping Across RAID 6) ............................................................... 27
Appendix A. Additional Resources.......................................................................... 29
Tables
Table 1. Comparison of PERC H700 and PERC H800 to previous PERC 6/I and PERC 6/E..............5
Table 2. 6Gb/s SAS (SAS 2.0) Features ..................................................................... 10
Table 3. SAS Performance Details ........................................................................... 10
Table 4. PowerEdge Server Support with PERC H700 and PERC H800.................................. 11
Table 5. Operating System Support with PERC H700 and PERC H800 .................................. 12
Table 6. Drive Support ........................................................................................ 12
Table 7. PERC H700 and PERC H800 Features ............................................................. 13
Table 8. RAID Level Migration................................................................................ 16
Table 9. Resource Contact Information and Descriptions................................................ 29
Figures
Figure 1. PERC H700 Integrated (Additional Sled for PCIe Slot) ...........................................6
Figure 2. PERC H700 Modular ...................................................................................7
Figure 3. PERC H800 Adapter ...................................................................................8
Figure 4. Example of RAID 0 .................................................................................. 22
Figure 5. Example of RAID 1 (Mirroring) ..................................................................... 23
Figure 6. Example of RAID 5 (Single Virtual Disk with 5 drives).......................................... 24
Figure 7. Example of RAID 6 (Single Virtual Disk with 5 drives).......................................... 25
Figure 8. Example of RAID 10 (1 + 0) ........................................................................ 26
Figure 9. Example of RAID 50 (5 + 0) ........................................................................ 27
Figure 10. Example of RAID 60 (6 + 0) ........................................................................ 28

Dell
DELL PERC H700 and H800 Technical Guide 5
1Product Comparison
1.1 Overview
The PERC H700 (internal) and PERC H800 (external) RAID controllers mark the next stage in the
evolution of the Dell™PowerEdge™ RAID controller portfolio with the introduction of 6Gb/s SAS (SAS
2.0). PERC H700 and H800 will be supported in PowerEdge 11th Generation servers. The PERC H700 is
follow-on to the PERC 6/I, and the PERC H800 is the follow-on to the PERC 6/E.
Table 1. Comparison of PERC H700 and PERC H800 to previous PERC 6/I and PERC 6/E
Feature/Spec
NEW
PERC H700
PERC 6/I
NEW
PERC H800
PERC 6/E
Interface
6Gb (SAS 2.0)
3Gb (SAS 1.1)
6Gb (SAS 2.0)
3Gb (SAS 1.1)
Bus support
x8 PCIe 2.0
x8 PCIe 1.0
x8 PCIe 2.0
x8 PCIe 1.0
Ports / Channels
8 (2 x4)
8 (2 x4)
8 (2 x4)
8 (2 x4)
Int/Ext
Connectors
2 internal
2 internal
2 external
2 external
Cache Memory
512MB BBU 512MB
Non-Volatile
Cache
(800 MHz DDR2)
256MB
(667 MHz DDR2)
512MB TBBU
512MB TNVC
1GB TNVC
(800 MHz DDR2)
256MB / 512MB
(667 MHz DDR2)
Battery-Backed
Cache
Yes
Yes
Yes
Transportable
Yes
Transportable
RAID Levels
0, 1, 5, 6, 10, 50,
60
0, 1, 5, 6, 10, 50,
60
0, 1, 5, 6, 10, 50,
60
0, 1, 5, 6, 10, 50,
60
Max physical
drives in Large
RAID volume
(R10, R50, R60)
16
10
192
(8x MD1220)
144
(6x MD1120)
HDD Support
SAS and SATA
SAS and SATA
SAS only
SAS and SATA
SSD Support
SAS and SATA
SATA
SAS only
Not Supported
SED Support
Yes (Local Key
Management)
Not Supported
Yes (Local Key
Management)
Not Supported
Controller
Firmware
(latest rev)
7.1
6.2
7.1
6.2
Redundant Path
No
No
Yes
Yes
I/O Load
Balancing
No
No
Yes
Yes
Cluster Support
No
No
No
No
Storage
Management
OpenManage™6.2
(minimum rev)
OpenManage™5.4
(minimum rev)
OpenManage™6.2
(minimum rev)
OpenManage™5.4
(minimum rev)

Dell
DELL PERC H700 and H800 Technical Guide 6
1.2 PERC H700 Overview
The PERC H700 internal host-RAID product offers three different models to support 11th Generation
Dell PowerEdge servers:
The PERC H700 Integrated card with two x4 internal mini-SAS ports supports the PCIe 2.0 x8
host interface. Cache options include standard 512 MB with battery backup unit (BBU), 512 MB
non-volatile (NV) cache, or 1 GB non-volatile cache. The PERC H700 Integrated card is
installed in the dedicated internal storage slot of the server. See Figure 1 for a view of the
PERC H700 Integrated card.
The PERC H700 Adapter with two x4 internal mini-SAS ports supports the PCIe 2.0 x8 host
interface. Cache options include standard 512 MB with BBU, 512 MB non-volatile cache, or
1 GB non-volatile cache. The PERC H700 Adapter is installed in a PCIe slot in the server. See
Figure 1 for a view of the PERC H700 Integrated card (adapter version is the same with the
addition of a sled for adhering to the PCIe slot connection).
The PERC H700 Modular card with one x4 internal SAS port and a BBU supports the PCIe 2.0 x4
host interface. The PERC H700 Modular card is installed in the integrated slot in the blade
server platforms. See Figure 2 for a view of the PERC H700 Modular card.
Figure 1. PERC H700 Integrated (Additional Sled for PCIe Slot)

Dell
DELL PERC H700 and H800 Technical Guide 7
Figure 2. PERC H700 Modular
1.3 PERC H800 Overview
The PERC H800 external host-RAID product is supported with 11th Generation Dell PowerEdge servers
for expanding storage to the Dell™PowerVault™MD1200 and MD1220 6Gb/s SAS enclosures.
The PERC H800 Adapter with two x4 external mini-SAS ports supports the PCIe 2.0 x8 host interface.
Cache options include the standard 512 MB transportable battery backup unit (TBBU) and the
transportable 512 MB and 1 GB non-volatile cache. The PERC H800 Adapter is installed in a PCIe slot
in the server. See Figure 3 for an angled view of the PERC H800 adapter.

Dell
DELL PERC H700 and H800 Technical Guide 8
Figure 3. PERC H800 Adapter

Dell
DELL PERC H700 and H800 Technical Guide 9
2New Features
2.1 Overview
The PERC H700 and PERC H800 offer the new CacheCade feature:
•Produces cost-effective performance scaling for database-type applications
•Offloads Random Reads to Dell-qualified Enterprise SSD configured as CacheCade SSD
•Has a standard feature of 1 GB NV cache (PERC H700/H800)
The PERC H700 and PERC H800 continue to offer the following features:
•512 MB and 1 GB non-volatile cache (not supported on H700 modular)
oData retention in cache is extended from hours to years in the event of power
interruption
oLarger cache size of 1 GB
•Cut-through IO (CTIO)
oPerformance boost of up to 2X IOPS performance
oOptimized for superior IOPS of SSDs over HDDs
oIdeal for small-block random workloads
oEasy to enable
•Physical disk power management
oConserve power by spinning down hot spares and unconfigured drives when not in use
oParameters are user-managed
•PCI-Express Gen2.0 support
•6Gb/s SAS (SAS 2.0) host interface
oDoubles the throughput performance
oSupport for Self Encrypting Drive (SED)—requires unique SED HDD part numbers
•New LSI 2108 ROC (Raid-on-Chip) with increased I/O processor (IOP) performance
•Increased internal drive support (up to 16 drives)
•SAS SSD support for specific 11th Generation Dell PowerEdge servers
•RAID volumes can be migrated from PERC 6/I, PERC 6/E, SAS 6/IR and PERC H200 controllers.
Backwards migration is not supported.
•Change in Virtual Disk default read cache policy (The default VD read cache policy has been
changed to Adaptive Read Ahead from No Read Ahead.)
•Display of expected and negotiated link rate for drives
The PERC H800 also offers the following features for PowerVault MD1200 and MD1220 enclosures:
•Increased capacity and scalability—up to 192 drives on one host-RAID controller
•Increased flexibility
oMix of 2.5” (MD1220) and 3.5” (MD1200) enclosures behind a PERC H800
oMix of 2.5” and 3.5” drives in the MD1200
•SAS SSD support for Dell PowerVault MD1200 and MD1220 enclosures
•22-drive RAID-10 can be configured with PERC H800 in the CTRL-R BIOS utility
2.2 6Gb/s SAS (SAS 2.0) Overview
The 6Gb/s SAS 2.0 specification doubles the current 3Gb/s SAS data transfer rate. 6Gb/s SAS is
designed for backward compatibility with 3Gb/s SAS and 3Gb/s SATA hard drives. Regardless of the
drive speed, 6Gb/s controllers will deliver significant performance improvements in both read and
write applications as compared to their 3Gb/s predecessors.

Dell
DELL PERC H700 and H800 Technical Guide 10
Other new features of the 6Gb/s SAS controllers will offer improved signal integrity and additional
safeguards to enhance data protection with support for SED (Self-Encrypting Drive) technology.
Table 2. 6Gb/s SAS (SAS 2.0) Features
DAS-based
Server Storage
6Gb/s Throughput

3Gb/s Compatible

Standard Mini-SAS Connectors (SFF-8087
and SFF-8088)

DFE (Decision Feedback Equalization)
improved signaling

SSC (Spread Spectrum Clocking) reduced
radiated emissions

Enhanced Security with SED (Self-
Encrypting Drive) support

Improved Scalability

2.2.1 6Gb/s SAS Performance Benefit over 3Gb/s SAS
In small disk drive configurations (one to eight drives) the aggregate media rate of the disks (the
speed at which the disk heads can read and write data) become the bottleneck for storage
throughput. As business storage needs grow, IT centers can add more disk drives to their storage
infrastructure, and the latest generation of SAS allows server performance to scale past the 3Gb/s
SAS performance limitations: from 2.4 GB/s to 4.8 GB/s unidirectional.
Table 3. SAS Performance Details
SAS Generation
PCI-Express
Interface
Approximate number of SAS
HDDs required saturate
bandwidth (RAID 0)
1.0 (3Gb)
1.0
8 to10
2.0 (6Gb)
2.0
16 to 20
In addition to the improvements in the SAS bandwidth, PCI Express 2.0 provides double the system-
to-storage controller interconnect speed. The x8 PCI Express 1.0 interface linking the controller to
the host platform limited throughput even further to a theoretical 2GB/s maximum, that limitation
has been raised to 4GB/s (unidirectional).
2.2.2 6Gb/s SAS Expectation
RAID controllers employing 6Gb/s SAS technology excel in both high IOP and high bandwidth
applications. Applications and environments that benefit most range from traditional data center
applications (such as random IOPs intensive email, web and database servers) to streaming and
archival applications that will benefit from improved sequential read and write throughput. This
means more users, more video streams, more email accounts, and faster backups are now possible.

Dell
DELL PERC H700 and H800 Technical Guide 11
3Product Support
3.1 Dell PowerEdge Server Support
The Dell PERC H700 and PERC H800 are supported with 11th Generation Dell™ PowerEdge™servers.
Refer to Table 1 for the 11th Generation PowerEdge servers that support the PERC H700 and PERC
H800. For the latest Dell PERC support matrix with Dell PowerEdge servers, visit the PERC web page
at www.dell.com/PERC.
Table 4. PowerEdge Server Support with PERC H700 and PERC H800
PERC H700 Internal
Integrated
PERC H700
Internal
Adapter
PERC H700 Internal
Modular
PERC H800 External
Adapter
R510
R610
T610
R710
T710
R715
R810
R815
R910
R310
T310
R410
T410
M610
M610x
M710
M910
T310
R310
R410
T410
R510
R610
T610
M610x
R710
T710
R715
R810
R815
R910
3.2 Management Software Support
The Dell PERC H700 and H800 are supported with 11th Generation Dell PowerEdge servers and
managed through common Dell OpenManage™Storage Management software (minimum version 6.2).
For pre-OS configuration, the PERC BIOS utility can also be used to configure and troubleshoot the
PERC H700 and PERC H800 products.
3.3 Operating System Support
The Dell PERC H700 and PERC H800 provide operating system support based on Dell 11th Generation
PowerEdge support requirements as shown in Error! Reference source not found.. For the latest list
of supported operating systems and driver installation instructions, see the system documentation on
the Dell Support website at support.dell.com/manuals. For specific operating system service pack
requirements, see the Drivers & Downloads page on the Dell Support website.

Dell
DELL PERC H700 and H800 Technical Guide 12
Table 5. Operating System Support with PERC H700 and PERC H800
Supported Operating Systems
Microsoft®Windows Server®2003 Family
Microsoft Windows Server 2008 Family
Microsoft Windows Server 2008 R2
Red Hat®Enterprise Linux®Version 4 and Version 5
RHEL 4.7 and later (32 and 64 bit)
RHEL 5.3 and later (32 and 64 bit)
Sun®Solaris™ 10 (64-bit)
Novell®SUSE®Linux®Enterprise Server Version 10 (64-bit) and Version 11 (64-bit)
SLES10 SP2 and later
SLES11 GM and later
VMware®vSphere™ 4.1 (including VMware ESX®4.1 or VMware ESXi™ 4.1)
For the most up-to-date information on supported operating systems, see the Operating System
Support Matrix for Dell PowerEdge Systems on Dell.com.
3.4 Drive Support
The Dell PERC H700 supports SAS and SATA interface drives, both HDD (hard-disk drive) and SSD
(solid-state drive). The Dell PERC H800 supports SAS interface drives, both HDD and SSD. Refer to the
following table for drive support details. For specific form-factor and capacity support, see the
Technical Guidebook for your server at http://www.dell.com.
Non Dell certified drives will be blocked. For more information on the benefits of using Dell certified
drives, see the Dell Point of View paper Why Customers Should Insist on DELLTM Hard Drives for
Enterprise Systems.
Table 6. Drive Support
Drive Type
Interface
PERC H700
PERC H800
HDD
6Gb/s SAS
Yes
Yes
3Gb/s SAS
Yes
Yes
3Gb/s SATA
Yes
No
SSD
3Gb/s SAS
Yes
Yes
3Gb/s SATA
Yes
No
SATA interface drives are not supported with PERC H800 and the Dell PowerVault MD1200 and
MD1220 enclosures.

Dell
DELL PERC H700 and H800 Technical Guide 13
4Product Overview
4.1 PERC H700 and PERC H800 Overview
Table 7. PERC H700 and PERC H800 Features
Feature
PERC H700
Integrated/Adapter
PERC H700 Modular
PERC H800 Adapter
RAID Levels
0, 1, 5, 6, 10, 50, 60
0, 1, 5, 6, 10
0, 1, 5, 6, 10, 50, 60
Ports
2 x4 internal
mini-SAS wide
ports
1 x4 integrated
SAS wide
port
2 x4 external
mini-SAS wide
ports
Processor
Dell adapter
SAS RAID-on-
Chip, 8-port
with LSI 2108
chipset
Dell adapter
SAS RAID-on-
Chip, 4 lanes
with LSI 2108
chipset
Dell adapter
SAS RAID-on-
Chip, 8-port
with LSI 2108
chipset
Hardware
Exclusive OR (XOR)
Assistance
Yes
Yes
Yes
Battery Backup
(BBU)
Yes
Yes
Yes, transportable
Cache Memory
512MB BBU
512MB NVC
1GB NVC
integrated
DDR2
512MB
integrated
DDR2
512MB TBBU
512MB TNVC
1GB TNVC
DDR2
Cache Function
Write-Back, Write-Through, Adaptive Read Ahead, No-Read
Ahead, Read Ahead
Maximum number
of drives per large
RAID volume (R10,
R50, R60)
16 drives
4 drives
192 drives
(8 –MD1220)
Maximum number
of virtual disks
(RAID volumes) per
disk group
16
16
16
Multiple Virtual
Disks (RAID
volumes) per
controller
Up to 64
Up to 64
Up to 64
PCI-Express 2.0
Support
x8
x4
x8
Cut-through IO
Yes
Yes
Yes

Dell
DELL PERC H700 and H800 Technical Guide 14
Feature
PERC H700
Integrated/Adapter
PERC H700 Modular
PERC H800 Adapter
Physical Disk
Power
Management
Yes
Yes
Yes
RAID Level
Migration
Yes
Yes
Yes
On-line Capacity
Expansion
Yes
Yes
Yes
Non-Volatile Cache
Yes
No
Yes
SMART Support
Yes
Yes
Yes
Redundant Path
Support
N/A
N/A
Yes
Dedicated and
Global Hot Spares
Yes
Yes
Yes
Revertible Hot
Spares
Yes
Yes
Yes
Hot Swap Devices
Yes
Yes
Yes
Disk Roaming
Yes
Yes
Yes
Disk Migration
Yes
Yes
Yes
SED Support
Yes
Yes
Yes
Mixed Capacity
Physical Drive
Yes
Yes
Yes
Enclosures per
Port
N/A
N/A
Up to 4 per port
(total of 8 enclosures
per Adapter)
Enclosure Hot-Add
N/A
N/A
Yes
SAS port
connection LED
LEDs used to determine
the status of the SAS
port
Supported.
Port State; LED State
Power On State; Off
Reset State; Off
All links in port
Connected; Green On
1 or more links not
connected (only
applicable in wide port
configurations); Amber
On
All links in port
disconnected or Cable
disconnected; Off

Dell
DELL PERC H700 and H800 Technical Guide 15
Feature
PERC H700
Integrated/Adapter
PERC H700 Modular
PERC H800 Adapter
Clustering
Card and software
stack enables High
Availability Clusters
Not supported
4.2 CacheCade
CacheCade provides cost-effective performance scaling for database-type application profiles in a
host-based RAID environment by extending the PERC RAID controller cache with the addition of Dell-
qualified Enterprise SSDs.
CacheCade identifies frequently-accessed areas within a data set and copies this data to a Dell-
qualified, Enterprise SSD (SATA or SAS), enabling faster response time by directing popular Random
Read queries to the CacheCade SSD instead of to the underlying HDD.
Supporting up to 512 GB of extended cache, CacheCade SSDs must all be the same interface (SATA or
SAS) and will be contained in the server or storage enclosure where the RAID array resides.
CacheCade SSDs will not be a part of the RAID array.
CacheCade is a standard feature on, and only available with, the PERC H700/H800 1 GB NV Cache
RAID controller.
CacheCade SSDs can be configured using the PERC BIOS Configuration Utility or OpenManage.
4.3 Cut-Through IO
Cut-through IO (CTIO) is an IO accelerator for SSD arrays that boosts the throughput of devices
connected to the PERC Controller. It is enabled through disabling the write-back cache (enable
write-through cache) and disabling Read Ahead.
4.4 Reconfiguring Virtual Disks
There are two methods to reconfigure RAID virtual disks—RAID Level Migration (RLM) and Online
Capacity Expansion (OCE). RLM involves the conversion of a virtual disk to a different RAID level. OCE
refers to increasing the capacity of a virtual disk, which can be accomplished in three ways:
If there is a single virtual disk in a disk group and free space is available, the virtual disk’s
capacity can be expanded within that free space. If a virtual disk is created and it does not use
the maximum size of the disk group, free space is available.
Free space is also available when a disk group’s physical disks are replaced by larger disks using
the Replace Member feature.
A virtual disk's capacity can also be expanded by performing an OCE operation to add more
physical disks by encompassing all available free space on a given virtual disk, adding drives
and/or migrating to a different RAID level.
When a RLM/OCE operation is complete, a reboot is not necessary. For a list of RAID level migrations
and capacity expansion possibilities, see Table 1. The source RAID level column indicates the virtual
disk level before the RAID level migration and the target RAID level column indicates the RAID level
after the operation is complete. If you configure 64 virtual disks on a controller, you cannot perform
a RAID level migration or capacity expansion on any of the virtual disks. The controller changes the
write cache policy of all virtual disks undergoing a RLM/OCE to Write-Through until the RLM/OCE is
complete.
Note: RAID level migration and expansion is not supported on RAID levels 10, 50, and 60.

Dell
DELL PERC H700 and H800 Technical Guide 16
Table 8. RAID Level Migration
Source RAID
Level
Target RAID
Level
# of Physical
Drives
(Beginning)
# of Physical
Drives (End)
Capacity
Expansion
Possible
Description
RAID 0
RAID 1
1
2
No
Converting non-
redundant virtual disk
into a mirrored virtual
disk by adding one drive.
RAID 0
RAID 5
1 or more
3 or more
Yes
At least one drive needs
to be added for
distributed parity data.
RAID 0
RAID 6
1 or more
4 or more
Yes
At least two drives need
to be added for dual
distributed parity data.
RAID 1
RAID 0
2
2 or more
Yes
Removes redundancy
while increasing
capacity.
RAID 1
RAID 5
2
3 or more
Yes
Maintains redundancy
while doubling capacity.
RAID 1
RAID 6
2
4 or more
Yes
Two drives are required
to be added for
distributed parity data.
RAID 5
RAID 0
3 or more
3 or more
Yes
Converting to a non-
redundant virtual disk
and reclaiming disk space
used for distributed
parity data.
RAID 5
RAID 6
3 or more
4 or more
Yes
At least one drive needs
to be added for dual
distributed parity data.
RAID 6
RAID 0
4 or more
4 or more
Yes
Converting to a non-
redundant virtual disk
and reclaiming disk space
used for distributed
parity data.
RAID 6
RAID 5
4 or more
4 or more
Yes
Removing one set of
parity data and
reclaiming disk space
used for it.
4.5 Fault-Tolerance Features
Below is a list of features that provide fault tolerance to prevent data loss:
Non-volatile cache: extends data retention from hours to years
Support for SMART
Redundant path support (for PERC H800 only)
Physical disk failure detection

Dell
DELL PERC H700 and H800 Technical Guide 17
Physical disk rebuild using hot spares
Enclosure affinity
Parity generation and checking (for RAID 5, 50, 6, and 60 only)
Battery backup of controller cache to protect data
Detection of batteries with low charge after boot up
4.5.1 Non-Volatile Cache
Dell PERC controllers with non-volatile (NV) cache use the standard battery as contained in the Dell
PERC controllers with a battery back-up unit (BBU). The difference is in battery implementation:
The battery in the BBU offering retains the data in cache in the event of a power cycle for a
guaranteed period of 24 hours (typically up to 72 hours).
The battery in the NV cache offering will transfer the data from cache to flash in the event of
a power cycle, where the data will be retained for up to ten years.
4.5.2 Automatic Replace Member with Predicted Failure
A Replace Member operation can occur when there is a SMART predictive failure reporting on a drive
in a virtual disk. The automatic Replace Member is initiated when the first SMART error occurs on a
physical disk that is part of a virtual disk. The target drive needs to be a hot spare that qualifies as a
rebuild drive. The physical disk with the SMART error is marked as failed only after the successful
completion of the Replace Member. This avoids putting the array in degraded status. If an automatic
Replace Member occurs using a source drive that was originally a hot spare (that was used in a
rebuild), and a new drive added for the Replace Member operation as the target drive, the hot spare
reverts to the hot spare state after a successful Replace Member operation. To enable the automatic
Replace Member, use the Dell OpenManage storage management application.
4.5.3 Redundant Path with Load Balancing Support
The PERC H800 adapter can detect and use redundant paths to drives contained in enclosures. This
provides the ability to connect two SAS cables between a controller and an enclosure for path
redundancy. The controller is able to tolerate the failure of a cable or Enclosure Management
Module (EMM) by using the remaining path. When redundant paths exist, the controller automatically
balances I/O load through both paths to each disk drive. This load balancing feature increases
throughput to each drive and is automatically turned on when redundant paths are detected. To set
up your hardware to support redundant paths, see the Setting up Redundant Path Support on the
PERC H800 Adapter section in the PERC H700 and PERC H800 User’s Guide
(support.dell.com/manuals).
4.5.4 Failed Physical Disk Detection
The controller automatically detects and rebuilds failed physical disks when you place a new drive in
the slot where the failed drive resided or when an applicable hot spare is present. Automatic
rebuilds can be performed transparently with hot spares. If you have configured hot spares, the
controllers automatically try to use them to rebuild failed physical disks.
4.5.5 Using Replace Member and Revertible Hot Spares
The Replace Member functionality allows a previously commissioned hot spare to be reverted back to
a usable hot spare. When a drive failure occurs within a virtual disk, an assigned hot spare
(dedicated or global) is commissioned and begins rebuilding until the virtual disk is optimal. After the
failed drive is replaced (in the same slot) and the rebuild to the hot spare is complete, the controller
automatically starts to copy data from the commissioned hot spare to the newly inserted drive. After
the data is copied, the new drive is part of the virtual disk and the hot spare is reverted back to

Dell
DELL PERC H700 and H800 Technical Guide 18
being a ready hot spare. This allows hot spares to remain in specific enclosure slots. While the
controller is reverting the hot spare, the virtual disk remains optimal. The controller automatically
reverts a hot spare only if the failed drive is replaced with a new drive in the same slot. If the new
drive is not placed in the same slot, a manual Replace Member operation can be used to revert a
previously commissioned hot spare.
4.5.6 Enclosure Affinity
Enclosure affinity is used to set the preference for a hot spare to be used to rebuild a physical disk
that resides in the same physical enclosure. This does not preclude the hot spare from being
provisioned to a second enclosure if there are no other hot spares present. For example, if there are
two enclosures and each enclosure has a hot spare with affinity set, then upon a drive failure the hot
spare will be provisioned from the same enclosure as the failed drive.
Hot-spare enclosure affinity can be configured only if you are using an external storage enclosure.
4.5.7 Battery Back-up of Controller Cache
4.5.7.1 Battery Management
The transportable battery backup unit (TBBU) is a cache memory module with an integrated battery
pack that enables you to transport the cache module with the battery in a new controller. The TBBU
protects the integrity of the cached data on the PERC H800 adapter by providing backup power
during a power outage. The battery backup unit (BBU) is a battery pack that protects the integrity of
the cached data on the PERC H700 cards by providing backup power during a power outage. The
battery provides up to 24 hours of backup power for the cache memory.
4.5.7.2 Battery Learn Cycle
Learn cycle is a battery calibration operation performed by the controller periodically to determine
the condition of the battery. This operation cannot be disabled.
The time frame for completion of a learn cycle is a function of the battery charge capacity and the
discharge/charge currents used. For PERC H700 or H800 cards, the expected time frame for
completion of a learn cycle is approximately seven hours and consists of the following parts:
•Learn cycle discharge cycle: approximately three hours
•Learn cycle charge cycle: approximately four hours
During the discharge phase of a learn cycle, the PERC H700 or H800 battery charger is disabled and
remains disabled until the battery is discharged. After the battery is discharged, the charger is re-
enabled.
4.6 Physical Disk Hot Swapping
Hot swapping is the manual replacement of a unit in a disk subsystem while the subsystem is
performing its normal functions. The following requirements must be met before hot swapping a
physical disk:
•The system backplane or enclosure must support hot swapping.
•The replacement drive must be of the same protocol and drive technology. For example, only
a SAS HDD can replace a SAS HDD; only a SATA SSD can replace a SATA SSD.
•The replacement drive must be of equal or greater capacity than the one it is replacing.

Dell
DELL PERC H700 and H800 Technical Guide 19
4.7 Disk Roaming
The PERC H700 and H800 cards support moving physical disks from one cable connection or
backplane slot to another on the same controller. The controller automatically recognizes the
relocated physical disks and logically places them in the proper virtual disks that are part of the disk
group. Disk roaming can be performed only when the system is turned off. Disk roaming should not
be performed during RAID level migration (RLM) or online capacity expansion (OCE). This causes loss
of the virtual disk.
4.8 Disk Migration
The PERC H700 and H800 cards support migration of virtual disks from one controller to another
without taking the target controller offline. However, the source controller must be offline prior to
performing the disk migration. The controller can import RAID virtual disks in optimal, degraded, or
partially degraded states. A virtual disk cannot be imported if it is in an offline state.
Disks cannot be migrated back to previous PERC RAID controllers. When a controller detects a
physical disk with an existing configuration, it flags the physical disk as foreign, and it generates an
alert indicating that a foreign disk was detected. Disk roaming should not be used during RLM or
online capacity expansion OCE as it can cause loss of the virtual disk.
Virtual disks that are created on the PERC 6 and H200 family of controllers can be migrated to the
PERC H700 and H800 controllers without risking data or configuration loss. Migrating virtual disks
from the PERC H700 and H800 cards to PERC 6 or PERC H200 is not supported.
During the discharge phase of a learn cycle, the PERC H700 or H800 battery charger is disabled and
remains disabled until the battery is discharged. After the battery is discharged, the charger is re-
enabled.
4.9 PERC H700 and H800 Security Key and RAID Management
4.9.1 PERC H700 and H800 Security Key Implementation
The Dell PowerEdge RAID Controller (PERC) H700 and H800 cards support encryption of data on the
drives when using Dell qualified self-encrypting drives (SEDs). This feature provides protection to the
data at rest in the event of theft or loss of drives. There is one security key per controller which
resides in the controller memory and it can be managed by the user (local key management). The
security key is used by the controller to lock and unlock access to encryption-capable physical drives.
In order to take advantage of this feature, you need to create a security key on your PERC H700 or
PERC H800 controller and have Dell qualified SEDs.
4.9.2 Configuring and Managing Secured RAID
Dell OpenManage storage management applications enable you to create and manage a security key,
manage and configure the RAID system, create and manage multiple disk groups, control and monitor
multiple RAID systems, and provide online maintenance. The management applications for PERC
H700 and H800 include:
•Dell OpenManage Storage Management
•BIOS Configuration Utility

Dell
DELL PERC H700 and H800 Technical Guide 20
4.10 Virtual Disk Write Cache Policies
The write cache policy of a virtual disk determines how the controller handles writes to that virtual
disk. Write-Back and Write-Through are the two write cache policies and can be set on virtual disks
individually.
All RAID volumes will be presented as Write-Through (WT) to the operating system (Windows and
Linux) independent of the actual write cache policy of the virtual disk. The PERC cards manage the
data in cache independently of the operating system or any applications. You can use OpenManage or
the BIOS configuration utility to view and manage virtual disk cache settings.
In Write-Through caching, the controller sends a data-transfer completion signal to the host system
when the disk subsystem has received all the data in a transaction. In Write-Back caching, the
controller sends a data transfer completion signal to the host when the controller cache has received
all the data in a transaction. The controller then writes the cached data to the storage device in the
background.
The risk of using Write-Back cache is that the cached data can be lost if there is a power failure
before it is written to the storage device. This risk is mitigated by using a BBU on PERC H700 or H800
cards. Write-Back caching has a performance advantage over Write-Through caching. The default
cache setting for virtual disks is Write-Back caching. Certain data patterns and configurations
perform better with a Write-Through cache policy.
Write-Back caching is used under all conditions in which the battery is present and in good
condition.
Write-Through caching is used under all conditions in which the battery is missing or in a low-charge
state. Low-charge state is when the battery is not capable of maintaining data for at least 24 hours
in the case of a power loss.
Write-Back mode is available when the user selects Force WB with no battery. When Forced Write-
Back mode is selected, the virtual disk is in Write-Back mode even if the battery is not present. It is
recommended that you use power backup system when forcing Write-Back to ensure there is no loss
of data if the system suddenly loses power.
4.11 Virtual Disk Read Cache Policies
The read policy of a virtual disk determines how the controller handles reads to that virtual disk. The
read policies are:
•Always Read Ahead—Read-Ahead capability allows the controller to read sequentially ahead
of requested data and to store the additional data in cache memory, anticipating that the
data is required soon. This speeds up reads for sequential data, but there is little
improvement when accessing random data.
•No Read Ahead—Disables the Read-Ahead capability.
•Adaptive Read Ahead—When selected, the controller begins using Read-Ahead if the two
most recent disk accesses occurred in sequential sectors. If the read requests are random, the
controller reverts to No Read Ahead mode. Note: The default read cache setting for virtual
disks is Adaptive Read Ahead.