Dell D7532QT User manual

Mechanical Instruction
Disassembly Procedures:
Step Figure Remark
S1. Remove the
Package_Buckles
and open the
carton.
Remove he 6 pcs
Package_Buckles, then
use a proper tool to
open the carton. Uplift
the top paper-box
slowly. Remove the
EPS-TOP and
accessories PE
bag(remote control
and battery(AA*2),
stylus*2pcs, Power
cable(varies by
contries), HDMI 2.0
cable, DP 1.2 cable,
USB 3.1 Gen 1
upstream cable, Wire
Saddle *5 pcs and
QSG.
S2. Remove the
desiccants
Take out 4pcs desiccant
from the bag. Use a
machine jip to take out
the whole monitor from
EPS-bottom. Remove
the PE bag from top to
bottom, and put the
monitor on ESD
protection foam.
Desiccant *2 Desiccant *2

Step Figure Remark
S3. Before
disassembly
Turn off power,
Unplug external
cables from product
S4. Remove the
Rear cover
Use a Philips-head
screwdriver to remove 8
screws for removing the
DIE-CASTING.
(No.1~8 screw
size=M4x10;
Torque=12±2kgf.cm)
Use a Philips-head
screwdriver to remove
17 screws for removing
the Rear Cover.
(No.1~17 screw
size=P3x6;
Torque=6±1kgf.cm)
Use a Philips-head
screwdriver to remove
33 screws for removing
the Rear Cover.
(No.1~33 screw
size=M4x6;
Torque=6±1kgf.cm)
(No.1~2 screw
size=M3x10;
Torque=6±1kgf.cm)

S5. Tear off the
tapes,clips and
disconnect all of
the connectors
S6. Remove the
Main board，
Power board ,OPS
board, Converter
board,etc
Use a Philips-head
screwdriver to remove
29 screws for removing
the Main board，Power
board ,OPS board,
Converter board.
(No.1~23 screw
size=M3x8
Torque= 4±1kgf.cm)
(No.24~28 screw
size=M4x6
Torque= 6±1kgf.cm)
(No.29 screw size=M4x6
Torque= 6±1kgf.cm)

Use a hexagonal
screwdriver to remove 7
screws.
(No.1~2 hex screw;
size=M3x8
Torque=4±1kgf.cm)
(No.3~5 hex screw;
size=M3x5
Torque=4±1kgf.cm)
(No.6~7 screw;
Torque=4.5±0.5kgf.cm )
S7. Remove the
BKT
Use a Philips-head
screwdriver to remove 5
screws for removing the
BKT.
(No.1~4 screw
size=M3x4
Torque=4±1kgf.cm )
(No.5 screw size=M4x6
Torque=4±1kgf.cm )
S8. Remove the
Speakers，I/O
board,Key board
Use a Philips-head
screwdriver to remove
18 screws of speakrers，
I/O board，key board.
(No.1~18 screw
size=M3x8
Torque=4±1kgf.cm )
Use a Philips-head
screwdriver to remove
10 screws for removing
the Key board
(No.1~4 screw
size=M3x6
Torque=4±1kgf.cm
(No.5~6 screw
size=M3x6
Torque=4±1kgf.cm

No.1~4 screw
size=M3x6
Torque=4±1kgf.cm)
S9. Remove the
Speaker BKT
Use a Philips-head
screwdriver to remove 4
screws for removing the
Speaker BKT
(No.1~4 screw
size=M4x5
Torque=6±1kgf.cm

Product material information
The following substances, preparations, or components should be disposed of or recovered
separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components No used
Batteries Product has LR03 batteries
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and liquids No used
Plastic containing BFR No used
Component and waste contain asbestos No used
CRT No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps No used
LCD display > 100 cm2 Product has an LCD greater than 100
cm2
External electric cable Product has external cables
Component contain refractory ceramic
fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors
(height > 25mm, diameter > 25mm)

Step Figure Remark
Remove the big
capacitors
Remove electrolyte
capacitors (red mark)
from printed circuit
boards
Take out bulk cap. pin
solder with soldering
iron and absorber
Lift the bulk cap up
and take it away from
the PCB

Tools Required
List the type and size of the tools that would typically can be used to disassemble the product to a
point where components and materials requiring selective treatment can be removed.
Tool Description:
- Phillip-head Screwdriver
- Hexagonal Screwdriver
- Penknife
- Soldering iron and absorber