Dell U2410 - UltraSharp - 24" LCD Monitor User manual

Dell™U2410FlatPanelMonitorUser'sGuide
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, notices, and cautions,
and they are used as follows:
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the caution is mandated by
regulatory authority.
Information in this document is subject to change without notice.
©2009-2011DellInc.Allrightsreserved.
Reproduction of these material in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo are trademarks of Dell Inc; Microsoft and Windows either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model U2410f
May2011Rev.A06
About Your Monitor
Setting Up the Monitor
Operating the Monitor
Solving Problems
Appendix
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loess of data if instructions are not
followed.
WARNING: A WARNING indicates a potential for property damage, personal injury or death.

Back to Contents Page
AboutYourMonitor
Dell™U2410FlatPanelMonitorUser'sGuide
Package Contents
Product Features
Identifying Parts and Controls
Monitor Specifications
Universal Serial Bus (USB) Interface
Card Reader Specifications
Plug and Play Capability
LCD monitor Quality and Pixel Policy
Maintenance Guidelines


Package Contents
Your monitor ships with the components shown below. Ensure that you have received all the components and contact Dell if something is missing.

NOTE: Some items may be optional and may not ship with your Monitor. Some features or media may not
be available in certain countries.
lMonitor
lStand
lPower Cable


Product Features
The U2410flatpaneldisplayhasanactivematrix,thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include:
■24-inch ( 518.4 mm x 324 mm) viewable area display measured diagonally.
■1920 x 1200 resolution, plus full-screen support for lower resolutions.
■Wide viewing angle to allow viewing from a sitting or standing position, or moving side-to-side.
■Tilt, swivel, rotation and height adjustment capabilities.
■Removable pedestal and Video Electronics Standards Association (VESA) 100 mm mounting holes for flexible mounting solutions.
■Plug and Play capability if supported by your system.
■On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.
■Software and documentation CD includes an information file (INF), Image color Matching File (ICM), and product documentation.
■Security lock slot.
Identifying Parts and Features
Front View
lVGA Cable (attached to the monitor)
lDVI Cable
lDP Cable
lUSB up stream cable (enables the USB ports and card reader on the monitor)
lDrivers and Documentation media
lQuick Setup Guide
lSafety Information

Back View

Front View
Control Panel
Label
Description
1-3
Shortcut keys
*The default settings are Preset Modes Select, Brightness/Contrast
Select and Input Source Select.
1
Preset Modes Select
2
Brightness/Contrast Select
3
Input Source Select
4
OSD Menu Select
5
Exit
6
Power Button (with power light indicator)
NOTE:1~5 buttons are capacitive touch buttons, which are activated by placing your finger on the blue LED.


BackViewBackViewwithmonitorstand

Side View
Label
Description/Use
1
VESA Mounting Holes (100mm)
(Behind attached VESA Plate)
To mount the monitor.
2
Connectors Label
To indicate the positions and types of
connectors.
3
Security Lock Slot
To help secure your monitor.
4
Dell Soundbar Mounting Brackets
To attach the optional Dell Soundbar.
5
Barcode Serial Number Label
To contact Dell for technical support.
6
Regulatory Rating Label
Lists the regulatory approvals.
7
Cable Management Slot
To organize cables by placing them through the
slot.


Bottom View

Bottom View
RightView
Left View
Label
Description
1
Card Reader. See Card Reader Specifications formoreinformation.
2
USB Down Stream Ports
Label
Description
1
AC Power Cord Connector
2
DCPowerConnectorforDell™Soundbar

Monitor Specifications
The following sections give you information about the various power management modes and pin assignments for various connectors for your monitor.
Power Management Modes
If you have VESA's DPMS compliance display card or software installed in your computer, the monitor automatically reduces its power consumption when not in
use. This is referred to as Power Save Mode. If input from keyboard, mouse or other input devices is detected by the computer, the monitor will automatically
"wake up". The following table shows the power consumption and signaling of this automatic power-savingfeature:
Activate the computer and wake up the monitor to gain access to the OSD.
Pin Assignments
VGA Connector
3
DisplayPort Connector
4
HDMI Connector
5
DVI Connector-1
6
DVI Connector-2
7
VGA Connector
8
Composite Video Connector
9
ComponentVideoConnectors
10
Audio Out (Support two channel output )
11
USB Upstream Port
12
USB Downstream Port
13
Stand Lock （Use a M3x14 threaded screw to
lock stand, screw not provided）
VESA Modes
Horizontal
Sync
Vertical Sync
Video
Power
Indicator
Power Consumption
Normal operation (with
max luminance, Dell
Soundbar and USB
active)
Active
Active
Active
Blue
132 W (Maximum)
Normal operation
Active
Active
Active
Blue
75 W (Typical)
Active-off mode
Inactive
Inactive
Blanked
Amber
Less than 1 W
Switch off
-
-
-
Off
Less than 1 W

NOTE: This monitor is TCO' 03 power management compatible.
NOTE: Zero power consumption in OFF mode can only be achieved by disconnecting the power cable from the
monitor.
Pin
Number
15-pin Side of the
Connected Signal Cable
1
Video-Red
2
Video-Green
3
Video-Blue
4
GND
5
Self-test
6
GND-R

DVIConnector
Composite Video Connector
7
GND-G
8
GND-B
9
Computer 5V/3.3V
10
GND-sync
11
GND
12
DDC data
13
H-sync
14
V-sync
15
DDC clock
Pin Number
24-pin Side of the Connected Signal Cable
1
TMDS RX2-
2
TMDS RX2+
3
TMDS Ground
4
Floating
5
Floating
6
DDC Clock
7
DDC Data
8
Floating
9
TMDS RX1-
10
TMDS RX1+
11
TMDS Ground
12
Floating
13
Floating
14
+5V/+3.3V power
15
Selftest
16
Hot Plug Detect
17
TMDS RX0-
18
TMDS RX0+
19
TMDS Ground
20
Floating
21
Floating
22
TMDS Ground
23
TMDS Clock+
24
TMDS Clock-

Luma composite chroma

Component Video Connector

DisplayPort Connector

Pin Number
3-pin Side of the Connected Signal Cable (Cable not
included)
1
Y (Luminance signal)
2
Pb (Color differential signal)
3
Pr (Color differential signal)
Pin
Number
20-pin Side of the Connected Signal
Cable
1
ML0(p)
2
GND
3
ML0(n)
4
ML1(p)
5
GND
6
ML1(n)
7
ML2(p)
8
GND
9
ML2(n)
10
ML3(p)
11
GND
12
ML3(n)
13
GND
14
GND
15
AUX(p)
16
GND
17
AUX(n)
18
HPD
19
Re-PWR
20
PWR


HDMI Connector

Pin
Number
19-pin Side of the Connected Signal
Cable
1
TMDS DATA 2+
2
TMDS DATA 2 SHIELD
3
TMDS DATA 2-
4
TMDS DATA 1+
5
TMDS DATA 1 SHIELD
6
TMDS DATA 1-
7
TMDS DATA 0+
8
TMDS DATA 0 SHIELD
9
TMDS DATA 0-
10
TMDS CLOCK
11
TMDS CLOCK SHIELD
12
TMDS CLOCK-
13
Floating
14
Floating
15
DDC CLOCK (SDA)
16
DDC DATA (SDA)
17
GROUND
18
+5V POWER
19
HOT PLUG DETECT
Flat Panel Specifications

Screen type
Active matrix -TFT LCD
Panel type
IPS
Screen dimensions
24 inches (24-inch diagonal viewable image size)
Preset display area:

Horizontal
518.4mm (20.41 inches)
Vertical
324.0mm (12.75 inches)
Pixel pitch
0.27mmx0.27mm
Viewing angle
178°(Vertical)typical,178°(Horizontal)typical
Luminance output
400 cd/m ²(typ)
Contrast ratio
1000:1 (typ), 80,000:1 (Max, Dynamic Contrast on)
Faceplate coating
Antiglare with hard-coating 3H
Backlight
7CCFL U-type system
Response Time
6ms panel typical (Grey to Grey)
Color Gamut
110 % (typ.)

* U2410 Color Gamut (Typical) is based on CIE1976 (110%) and CIE1931 (102%) .
Resolution

Horizontal scan range
30 kHz to 81 kHz (automatic)
Vertical scan range
56 Hz to 76 Hz
Maximum resolution
1920 x 1200 at 60 Hz
Video Supported Modes
Video display capabilities (DVI playback)
480i/480p/576i/576p/720p/1080i/1080p (Supports HDCP)
Video display capabilities (Composite playback)
NTSC/PAL
Video display capabilities (HDMI playback)
480i/480p/576i/576p/720p/1080i/1080p
Video display capabilities (Component playback)
480i/480p/576i/576p/720p/1080i/1080p
Preset Display Modes
The following table lists the preset modes for which Dell guarantees image size and centering:
Display Mode
Horizontal Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock (MHz)
Sync Polarity
(Horizontal/Vertical)
VGA, 720 x 400
31.5
70.1
28.3
-/+
VGA, 640 x 480
31.5
59.9
25.2
-/-
VESA, 640 x 480
37.5
75.0
31.5
-/-
VESA, 800 x 600
37.9
60.3
40.0
+/+
VESA, 800 x 600
46.9
75.0
49.5
+/+
VESA, 1024 x 768
48.4
60.0
65.0
-/-
VESA, 1024 x 768
60.0
75.0
78.8
+/+
VESA, 1152 x 864
67.5
75.0
108.0
+/+
VESA, 1280 x 1024
64.0
60.0
108.0
+/+
VESA, 1280 x 1024
80.0
75.0
135.0
+/+
VESA, 1600 x 1200
75.0
60.0
162.0
+/+
VESA, 1920 x 1200
74.5
60.0
154.0
+/-
Electrical
The following table lists the electrical specification:
Video input signals
Analog RGB, 0.7 Volts +/-5%,75ohminputimpedance
Digital DVI-D TMDS, 600mV for each differential line, 50 ohm input
impedance
HDMI, 600mV for each differential line, 100 ohm input impedance
per differential pair
DisplayPort, 600mV for each differential line, 100 ohm input
impedance per differential pair
Composite, 1 volt(p-p), 75 ohm input impedance
Component: Y, Pb, Pr are all 0.5~1volt(p-p), 75 ohm input
impedance 
Synchronization input signals
separate horizontal and vertical,
3.3V CMOS or 5V TTL level, positive or negative sync.
SOG (Sync on green)
AC input voltage/frequency/current
100 to 240 VAC/50 or 60 Hz +3 Hz/2.0A (Max.)
Inrush current
120V: 40A (Max.)
240V: 80A (Max.)
Physical Characteristics
The following table lists the physical characteristics:

Connector type
lVGA: Blue Connector
lDVI-D: White Connector
lDisplayPort: Black Connector
lComposite
lComponent
lHDMI
Signal cable type
lD-sub: Detachable, Analog, 15pin, shipped attached to the
monitor
lDVI-D: Detachable, Digital, 24pin, shipped detached from
the monitor
lDisplayPort: Detachable, Digital, 20pin, shipped detached
from the monitor
lComposite
lComponent
lHDMI
NOTE: The composite, component and HDMI cables are
not included with the monitor.
Dimensions (with stand)

Height (Compressed)
393.0mm (15.47 inches)
Height (Extended)
493.0 mm (19.40 inches)
Width
559.7 mm (22.03 inches)
Depth
201.5 mm (7.93 inches)
Dimensions (without stand)

Height
365.1mm (14.37 inches)
Width
559.7 mm (22.03 inches)
Depth
81.0 mm (3.18 inches)
Stand Dimensions

Height (Compressed)
340.7 mm (13.41 inches)
Height (Extended)
370.7 mm (14.59 inches)
Width
309.7 mm (12.19 inches)
Depth
201.5 mm (7.93 inches)
Weight

Weight with packaging
11.60 kg (25.64 lb)
Weight with stand assembly and
cables
9.57kg(19.93 lb)
Weight without stand assembly
(ForwallmountorVESAmount
considerations -no cables)
6.50 kg (14.30 lb)
Weight of stand assembly
2.41 kg (5.30 lb)
Environmental
The following table lists the environmental limitation:
Temperature

Operating
0°to40°C(32°to104°F)
Non-Operating
Storage: -20°to60°C (-4°to140°F)
Shipping: -20°to60°C(-4°to140°F)
Humidity



Universal Serial Bus (USB) Interface
USB Upstream Connector
USB Downstream Connector
USB Ports
l1 upstream - rear
l4 downstream - 2 on rear; 2 on left side
Operating
10% to 80% (noncondensing)
Non-Operating
Storage: 5% to 90% (noncondensing)
Shipping: 5% to 90%(noncondensing)
Altitude

Operating
3,657.6 m (12,000 ft) max
Non-Operating
12,192 m (40,000 ft) max
Thermal dissipation
375 BTU/hour (maximum)
195 BTU/hour (typical)
This monitor supports High-Speed Certified USB 2.0 interface.
Transfer speed
Data Rate
Power
Consumption
High speed
480 Mbps
2.5W(Max.,eachport)
Full speed
12 Mbps
2.5W(Max.,eachport)
Low speed
1.5 Mbps
2.5W(Max.,eachport)
Pin Number
4-pin Side of the connector
1
DMU
2
VCC
3
DPU
4
GND
Pin Number
4-Pin Side of the Signal Cable
1
VCC
2
DMD
3
DPD
4
GND

Card Reader Specifications
Overview
lThe Flash Memory Card Reader is a USB storage device that allows users to read and write information from and into the memory card.

lThe Flash Memory Card Reader is automatically recognized by Microsoft®Windows®2000, Windows®XP,Windows®Vista and Windows®7.

lOnce installed and recognized, each separate memory card (slot) appears as a separate drive/drive letter.

lAll standard file operations (copy, delete, drag-and-drop, etc.) can be performed with this drive.
Features
The Flash Memory Card Reader has the following features:
lSupports Microsoft®Windows®2000, Windows®XP, Windows®Vista and Windows®7 operating systems

lNo Microsoft®Windows®9X support from Dell

lMass Storage Class device (No drivers are required under Microsoft®Windows®2000, Windows®XP, Windows®Vista and Windows®7)

lUSB-IF certification

lSupports various memory card media

The following table lists the memory cards supported:
Maximum Card Capacity Supported by the U2410 card reader

General
NOTE: The monitor's 2.0 USB interface functions only if the computer is USB 2.0 compatible.
NOTE: The monitor's USB interface works only when the monitor is on or in power save mode. If you switch
the monitor off and then switch it on, the attached peripherals may take a few seconds to resume normal
functionality.
Slot Number
Flash memory cards type
1
xD-Picture Card
Memory Stick Card (MS)/High Speed Memory Stick (HSMS)/Memory Stick Pro Card (MS
PRO)/Memory Stick Duo (with Adapter)
Secure Digital Card (SD)/Mini Secure Digital (with Adapter)/TransFlash Card (with
Adapter)
MultiMedia Card (MMC)/Reduced Size MultiMedia Card (with Adapter)
Card type
Support Specification
Memory Card
Spec Version
Support Maximum
Capacity by Spec
U2410
MS
Memory Stick Standard Format Specification
1.43
128MB
Supported
MSPRO
Memory Stick Pro Standard Format Specifications
1.02
32GB
Supported
MSDuo
Memory Stick Duo Standard Format Specifications
1.10
128MB/32GB
Supported
MSDuo-HG
Memory Stick Duo Standard Format Specifications
1.01
32GB
Supported
xD
xD Picture Card Specification
1.2
2GB
Supported
SD
SD Memory Card Specifications
2.0
32GB
Supported
MMC
MultiMedia Card System Specification
4.2
32GB
Supported
NOTE: MSPRO includes MSPRO Duo and MS Micro.
NOTE: xD includes TypeM and TypeH.
NOTE: SD includes HS-SD, MiniSD and SD Micro. SD v2.0 spec includes SDHC.
NOTE: MMC includes MMCPlus, RS-MMC, MMC Mobile and MMC micro.
Connection type
USB 2.0 High Speed Device (USB Full Speed Device compatible)
Supported OS
Microsoft®Windows®2000, Windows®XP, Windows®Vista and Windows®7

Performance
Plug and Play Capability
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display
Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. If required, the
user can select different settings, but in most cases monitor installation is automatic.
LCD monitor Quality and Pixel Policy
During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and
do not affect the display quality or usability. For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at: support.dell.com.
Maintenance Guidelines
Caring for Your Monitor
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:
lTo clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the
antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
lUse a lightly-dampened,warmclothtocleantheplastics.Avoidusingdetergentofanykindassomedetergentsleaveamilkyfilmontheplastics.
lHandle your monitor with care as dark-colored monitors may scratch and show white scuff marks more than lighter-coloredmonitors.
Back to Contents Page

Transfer Speed
Read: 480 Mb/s (max.)

Write: 480 Mb/s (max.)
WARNING: Read and follow the Safety Instructionsbeforecleaningthemonitor.
WARNING: Before cleaning the monitor, unplug the monitor from the electrical
outlet.

Back to Contents Page

Appendix
Dell™U2410FlatPanelMonitorUser'sGuide
Safety Instructions
FCC Notice (U.S. Only) and Other Regulatory Information
Contacting Dell

WARNING: Safety Instructions
For information on safety instructions, see the Safety Information.
FCC Notice (U.S. Only) and Other Regulatory Information
For FCC notices and other regulatory information, see the regulatory compliance website located at www.dell.com\regulatory_compliance.
Contacting Dell
To contact Dell electronically, you can access the following websites and by phone:
lFor support through the web, go to support.dell.com.
lFor customers in the United States, call 800-WWW-DELL (800-999-3355).
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be
available in your area. To contact Dell for sales, technical support, or customer service issues:
1. Visit support.dell.com.
2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.
3. Click Contact Us on the left side of the page.
4. Select the appropriate service or support link based on your need.
5. Choose the method of contacting Dell that is convenient for you.
Back to Contents Page
WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock,
electrical hazards, and/or mechanical hazards.
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product
catalog.

Back to Contents Page

Setting Up Your Monitor
Dell™U2410FlatPanelMonitor
If you have a Dell™desktop or a Dell™portable computer with internet access
1. Go to http://support.dell.com,enteryourservicetag,anddownloadthelatestdriverforyourgraphicscard.
2. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1920 x 1200 again.

Back to Contents Page
NOTE: If you are unable to set the resolution to 1920 x 1200, please contact Dell™
toinquireaboutaGraphicsAdapterthatsupportstheseresolutions.

Back to Contents Page

Setting Up Your Monitor
Dell™U2410FlatPanelMonitor
If you have non Dell™desktop, portable computer, or graphic card
1. Right-click on the desktop and click Properties.
2. Select the Settings tab.
3. Select Advanced.
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).
5. Please refer to the graphic card provider website for updated driver (for example, http://www.ATI.com OR http://www.NVIDIA.com ).
6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1920 x 1200 again.

Back to Contents Page
NOTE: If you are unable to set the resolution to 1920 x 1200, please contact the manufacturer of your computer or consider purchasing a graphics
adapterthatwillsupportthevideoresolutionof1920x1200.

Back to Contents Page

Operating the Monitor
Dell™U2410FlatPanelMonitorUser'sGuide
Using the Front Panel Controls
Using the On-Screen Display (OSD) Menu
Setting the Maximum Resolution
Using the Dell Soundbar (Optional)
Using the Tilt, Swivel and Vertical Extension
Rotating the monitor
Adjusting the Rotation Display Settings of Your System

Using the Front Panel
Use the buttons on the front of the monitor to adjust the image settings. 1~5 are capacitive touch sensor keys, activated by placing the finger on the Blue LED
button.

1-3
Shortcut keys
Use this key for direct access to the control menu that you define in the personalize menu.
For example, use the second shortcut key to activate Brightness/Contrast adjustment.
*The default settings are Preset Modes Select, Brightness/Contrast Select and Input Source Select.
1
Preset Modes Select
Use this button to select different image modes on your monitor.
2
Brightness/Contrast
Use this button for direct access to the "Brightness/Contrast" control menu.
3
Input Source Select
Use Input Source Select button to select between different video signals that may be connected to your monitor.
lVGA input
lDVI-D 1 input
lDVI-D 2 input
lDisplayPort input

lHDMI input
lComponent video input
lComposite video input
Displays the source selection bar. Touch and buttons to move between the setting options and Touch
to select the input
source you want.
If VGA or DVI-D or DisplayPort or HDMI input is selected and all VGA and DVI-
D and DisplayPort and HDMI cables are not connected, a
floating dialog box as shown below appears.
or

If either Composite, or Component input is selected and the cables are not connected or the video source is turned off, the screen does
not have an image. If any button is Touched (except power button), the monitor displays the following message:
or
or
or
4
OSD Menu
Use this key to open the on-screen display (OSD). See Using the OSD Menu.