Dell VxRail P670F Manual

Dell VxRail™ P670F, P670N, V670F, and S670
Installation and Service Manual
March 2023
Rev. 10

Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2021 - 2023 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its
subsidiaries. Other trademarks may be trademarks of their respective owners.

Revision history..........................................................................................................................................................................4
Chapter 1: Introduction................................................................................................................. 5
Dell Technologies Support.................................................................................................................................................5
Register for a Dell Technologies Support account................................................................................................ 5
Where to go for support resources...........................................................................................................................5
Use SolVe Online for VxRail procedures.................................................................................................................. 6
Locate your VxRail serial number.................................................................................................................................... 6
Look up your VxRail serial number in VxRail Manager.......................................................................................... 6
Locate the serial number and service tag number on your VxRail.....................................................................6
Chapter 2: System overview.......................................................................................................... 7
Front view of the system...................................................................................................................................................7
Rear view of the system.................................................................................................................................................... 8
Inside the system .............................................................................................................................................................. 13
Chapter 3: Initial setup and configuration.................................................................................... 16
Chapter 4: Pre-operating system management applications......................................................... 17
Manage the pre-operating system applications..........................................................................................................17
iDRAC configuration.......................................................................................................................................................... 17
Log in to iDRAC............................................................................................................................................................ 17
Chapter 5: Replacement of hardware components....................................................................... 19
Use SolVe Online for VxRail procedures...................................................................................................................... 19
Supported hardware components................................................................................................................................. 19
System memory guidelines..............................................................................................................................................20
General memory module installation guidelines....................................................................................................22
Intel Persistent Memory 200 series installation guidelines .............................................................................. 23
Expansion card installation guidelines.......................................................................................................................... 26
Chapter 6: System diagnostics and indicator codes.....................................................................35
Status LED indicators.......................................................................................................................................................35
System health and system ID indicator codes........................................................................................................... 36
iDRAC Quick Sync 2 indicator codes............................................................................................................................36
iDRAC Direct LED indicator codes................................................................................................................................ 37
NIC indicator codes...........................................................................................................................................................37
Power supply unit indicator codes................................................................................................................................ 38
Drive indicator codes........................................................................................................................................................39
Using system diagnostics................................................................................................................................................ 39
Dell Embedded System Diagnostics........................................................................................................................39
Contents
Contents 3

Revision history
Date Revision Description of change
March 2023 10 Minor updates.
January 2023 9 Updated for VxRail software version 8.0.010.
December 2022 8 Updated for VxRail software version 8.0.000.
August 2022 7 Updated for VxRail software version 7.0.380.
May 2022 6 Updated for VxRail software version 7.0.360.
February 2022 5 Updated for VxRail software version 7.0.320; added BOSS-S1 support for P670F and
V670F.
December 2021 4 Updated for VxRail self-deployment information.
November 2021 3 Updated for VxRail software version 7.0.300, updated the PSU as fault tolerant
redundant, and added the support for 256 GB LRDIMM for VxRail P670F.
August 2021 2 Updated to include support for Intel Persistent Memory 200 series (BPS) and minor
updates.
July 2021 1 Initial wide release.
4 Revision history

Introduction
The VxRail P670F, P670N, V670F, and S670 Installation and Service Manual provides an overview about the system, diagnostic
tools, and guidelines describing high-level operations.
The target audience for this document includes customers, field personnel, and partners who want to operate and maintain a
VxRail P670F, P670N, V670F, or S670. This document is designed for people familiar with:
●Dell systems and software
●VMware virtualization products
●Data center appliances and infrastructure
For the most up-to-date list of VxRail documentation, see the VxRail Documentation Quick Reference List.
Dell Technologies Support
Create a Support account to access support resources for your VxRail. Link your Support account with VxRail Manager to
access resources without a separate login.
If you already have an account, register your VxRail to access the available resources. You can link your Online Support account
with VxRail Manager and access support resources without having to log in separately.
Register for a Dell Technologies Support account
Create a Dell Technologies Support account to obtain VxRail documentation, license files, software updates.
About this task
If you already have an account, link your Support account with VxRail Manager and access support resources without having to
log in separately.
After you register, you can:
●Access or download the SolVe Desktop application for customized procedures to replace hardware components and upgrade
software components.
●Link your Support account for access to resources from within VxRail Manager.
For information about how to access a Dell Technologies Online Support account or to upgrade an existing account, see KB
21768.
Steps
1. Go to Dell Technologies Support.
2. Select Create an Account and follow the steps to create an account.
It may take approximately 48 hours to receive a confirmation of account creation.
Where to go for support resources
Support resources are available for your VxRail.
Use the following resources to obtain support for your VxRail:
●In the VMware vSphere Web Client, select VxRail. Use the Support functions on the VxRail Dashboard.
●Go to Dell Technologies Support.
1
Introduction 5

Use SolVe Online for VxRail procedures
To avoid potential data loss, always use SolVe Online for VxRail to generate procedures before you replace any hardware
components or upgrade software.
CAUTION: If you do not use SolVe Online for VxRail to generate procedures to replace hardware components or
perform software upgrades, data loss may occur for VxRail.
You must have a Dell Technologies Support account to use SolVe Online for VxRail.
See KB 124395 for more information about how to use SolVe.
Locate your VxRail serial number
To get support for your VxRail, use the VxRail serial number, also called the Product Serial Number Tag (PSNT). The PSNT is a
14-digit number that is used to identify an individual VxRail on Dell Technologies support.
NOTE: While contacting the Dell Technologies Customer Support, use the PSNT for the identification of your VxRail. If
Customer Support asks for the 7-digit service tag number, provide it.
The two identification tags on your VxRail are located as follows:
●The VxRail serial number tag: You can find the PSNT printed on the information tag on your VxRail, or you can locate the
PSNT using VxRail Manager.
●The service tag: You can find the service tag that is printed on your VxRail.
Look up your VxRail serial number in VxRail Manager
Look up your VxRail serial number in VxRail Manager.
Steps
1. From the VMware vSphere Web Client, click Hosts and Clusters in the left navigation bar.
2. Select your VxRail cluster.
3. Select the Monitor tab.
4. From the inner left navigation bar, select VxRail > Physical View.
Locate the serial number and service tag number on your VxRail
You can identify your VxRail using the unique serial number, service tag number, or express service code located on the
information tag of your VxRail. The information tag is located at the front of your VxRail. See System overview for the location.
The information tag contains the following:
●Product serial number tag (PSNT), which provides the 14-digit VxRail serial number
●Service tag
To view the PSNT and other labels, pull out the information tag in the front of the VxRail. Alternatively, information may be on a
sticker on the chassis of VxRail.
The mini Enterprise Service Tag (EST) is found on the back of VxRail. This information is used by Dell to route support calls to
the appropriate personnel.
6Introduction

System overview
The VxRail P670F is a 2U server that supports:
●Up to two third-generation Intel Xeon Scalable processors
●16 DDR4 DIMM slots for single-socket configuration and 32 DDR4 DIMM slots for dual-socket configuration
●Two fault tolerant redundant (FTR) mixed mode power supply units
●The following storage configurations:
○For a single-socket configuration: Up to 24 x 2.5-inch SAS/SATA front disk drives with four universal slots to support
optional NVMe drives. No support for rear disk drive.
○For a dual-socket configuration: Up to 24 x 2.5-inch SAS/SATA front disk drives (with four universal slots to support
optional NVMe drives) and 4 x 2.5-inch SAS/SATA rear disk drives.
The VxRail P670N is a dual-socket, 2U server that supports:
●Two third-generation Intel Xeon Scalable processors
●32 DDR4 DIMM slots
●Two FTR mixed mode power supply units
●Up to 24 x 2.5-inch all NVMe front disk drives
●DPU/SmartNIC
You cannot mix different capacity drives in VxRail P670N.
The VxRail V670F is a dual-socket, 2U server that supports:
●Two third-generation Intel Xeon Scalable processors
●32 DDR4 DIMM slots
●Two FTR mixed mode power supply units
●Up to 24 x 2.5-inch SAS/SATA front disk drives (with four universal slots to support optional NVMe drives)
●DPU/SmartNIC
The VxRail S670 is a 2U server that supports:
●Up to two third-generation Intel Xeon Scalable processors
●32 DDR4 DIMM slots
●Two FTR mixed mode power supply units
●Up to 12 x 3.5-inch SAS/SATA front disk drives with 4 x 2.5-inch SAS/SATA/NVMe rear disk drives.
NOTE: All instances of SAS, SATA drives, PCIe SSDs, and NVMe are referred to as drives in this document, unless specified
otherwise.
For more information about supported drives, see the Dell VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
Front view of the system
The following figure shows the front view of the VxRail P670F, P670N, and V670F 24 x 2.5-inch drive system:
The following figure shows the front view of the VxRail S670 12 x 3.5-inch drive system:
2
System overview 7

Item Ports, panels, and
slots
Icon Description
1 Left control panel N/A Contains the system health, system ID, status LED, and the iDRAC Quick Sync 2
(wireless) indicator.
NOTE: The iDRAC Quick Sync 2 is an optional offering for VxRail P670F, P670N,
V670F, and S670.
●Status LED: Enables you to identify any failed hardware components. There are
up to five status LEDs and an overall system health LED (Chassis health and
system ID) bar. For more information, see the Status LED indicators section.
●Quick Sync 2 (wireless): Indicates a Quick Sync enabled system. The Quick
Sync feature is optional. This feature allows management of the system by
using mobile devices called as OpenManage Mobile (OMM) feature. Using iDRAC
Quick Sync 2 with OpenManage Mobile (OMM) aggregates hardware or firmware
inventory and various system level diagnostic and error information that can be
used in troubleshooting the system. For more information, see the Integrated
Dell Remote Access Controller User's Guide available at https://www.dell.com/
idracmanuals.
2 Drive N/A Enables you to install drives that are supported on your system.
3 Right control panel N/A Contains the power button, USB port, iDRAC Direct micro port, and the iDRAC
Direct status LED.
4 Information tag N/A The Information tag is a slide-out label panel that contains system information such
as Service Tag and PSNT. If you have opted for the secure default access to iDRAC,
then the Information tag will also contain the iDRAC secure default password.
For more information, see the Dell VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
Rear view of the system
The following figure shows the rear view of VxRail P670F (single-socket configuration):
8System overview

Item Ports, panels, or slots Icon Description
1 PCIe expansion card riser
1 (slot 1 and slot 2)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
2 BOSS S2 module N/A This slot supports the BOSS S2 module.
3 PCIe expansion card riser
2 (slot 3)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
4 OCP NIC port N/A This port supports OCP 3.0. The NIC ports are integrated on the
OCP card which is connected to the system board.
5 USB 2.0 port (1) This port is USB 2.0-compliant.
6 Power supply unit (PSU
2)
For more information about the PSU configurations, see the Dell
VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
7 VGA port For more information about the VGA, see the Dell VxRail™ P670F,
P670N, V670F, and S670 Technical Specifications.
8 USB 3.0 port (1) This port is USB 3.0-compliant.
9 iDRAC dedicated port Enables you to remotely access iDRAC. For more information, see the
iDRAC User's Guide at www.dell.com/poweredgemanuals.
10 System identification
button
Press the system ID button:
●To locate a particular system within a rack.
●To turn the system ID on or off.
To reset iDRAC, press and hold the button for more than 16 s.
●To reset iDRAC using system ID, ensure that the system ID
button is enabled in the iDRAC setup.
●If the system stops responding during POST, press and hold the
system ID button (for more than 5 s) to enter the BIOS progress
mode.
11 NIC port (1,2) The NIC ports are embedded on the LOM card that is connected to
the system board.
System overview 9

Item Ports, panels, or slots Icon Description
12 Power supply unit (PSU 1) For more information about the PSU configurations, see the on
product documentation page.
For more information about supported drives, see the Dell VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
The following figure shows the rear view of the VxRail P670F (dual-socket configuration) and S670 with 4 x 2.5-inch rear drive
module:
Item Ports, panels, or slots Icon Description
1 Rear drive module N/A Enables you to install drives supported on your system. For more
information about drives, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
2 PCIe expansion card riser
2 (slot 3 and slot 6)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
3 Rear handle N/A To lift the system.
4 BOSS S2 module N/A This slot supports the BOSS S2 module.
5 USB 2.0 port (1) This port is USB 2.0-compliant.
6 PCIe expansion card riser
4 (slot 7 and slot 8)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
7 Power supply unit (PSU
2)
For more information about the PSU configurations, see the Dell
VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
8 VGA port For more information about the VGA, see the Dell VxRail™ P670F,
P670N, V670F, and S670 Technical Specifications.
9 USB 3.0 port (1) This port is USB 3.0-compliant.
10 iDRAC dedicated port Enables you to remotely access iDRAC. For more information, see the
iDRAC User's Guide at www.dell.com/poweredgemanuals.
11 System identification
button
Press the system ID button:
●To locate a particular system within a rack.
●To turn the system ID on or off.
To reset iDRAC, press and hold the button for more than 16 s.
●To reset iDRAC using system ID, ensure that the system ID
button is enabled in the iDRAC setup.
●If the system stops responding during POST, press and hold the
system ID button (for more than 5 s) to enter the BIOS progress
mode.
12 OCP NIC port N/A This port supports OCP 3.0. The NIC ports are integrated on the
OCP card which is connected to the system board.
10 System overview

Item Ports, panels, or slots Icon Description
13 NIC port (1,2) The NIC ports are embedded on the LOM card that is connected to
the system board.
14 Power supply unit (PSU 1) For more information about the PSU configurations, see the on
product documentation page.
For more information about supported drives, see the Dell VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
The following figure shows the rear view of the VxRail P670N and V670F:
Item Ports, panels, or slots Icon Description
1 PCIe expansion card riser
2 (slot 1 and slot 2)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
2 BOSS S2 module N/A This slot supports the BOSS S2 module.
3 PCIe expansion card riser
2 (slot 3 and slot 6)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
4 PCIe expansion card riser
2 (slot 4 and slot 5)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
5 USB 2.0 port (1) This port is USB 2.0-compliant.
6 PCIe expansion card riser
4 (slot 7 and slot 8)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
7 Power supply unit (PSU
2)
For more information about the PSU configurations, see the Dell
VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
8 VGA port For more information about the VGA, see the Dell VxRail™ P670F,
P670N, V670F, and S670 Technical Specifications.
System overview 11

Item Ports, panels, or slots Icon Description
9 USB 3.0 port (1) This port is USB 3.0-compliant.
10 iDRAC dedicated port Enables you to remotely access iDRAC. For more information, see the
iDRAC User's Guide at www.dell.com/poweredgemanuals.
11 System identification
button
Press the system ID button:
●To locate a particular system within a rack.
●To turn the system ID on or off.
To reset iDRAC, press and hold the button for more than 16 s.
●To reset iDRAC using system ID, ensure that the system ID
button is enabled in the iDRAC setup.
●If the system stops responding during POST, press and hold the
system ID button (for more than 5 s) to enter the BIOS progress
mode.
12 OCP NIC port N/A This port supports OCP 3.0. The NIC ports are integrated on the
OCP card which is connected to the system board.
13 NIC port (1,2) The NIC ports are embedded on the LOM card that is connected to
the system board.
14 Power supply unit (PSU 1) For more information about the PSU configurations, see the on
product documentation page.
For more information about supported drives, see the Dell VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
The following figure shows the rear view of the VxRail V670F with double width expansion card riser:
Item Ports, panels, or slots Icon Description
1 PCIe expansion card riser
2 (slot 2)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
2 BOSS S2 module N/A This slot supports the BOSS S2 module.
3 PCIe expansion card riser
2 (slot 3 and slot 6)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
12 System overview

Item Ports, panels, or slots Icon Description
4 PCIe expansion card riser
2 (slot 4 and slot 5)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
5 USB 2.0 port (1) This port is USB 2.0-compliant.
6 PCIe expansion card riser
4 (slot 7)
N/A The expansion card riser enables you to connect PCI Express
expansion cards. For more information about the expansion cards
supported on your system, see the Dell VxRail™ P670F, P670N,
V670F, and S670 Technical Specifications.
7 Power supply unit (PSU
2)
For more information about the PSU configurations, see the Dell
VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
8 VGA port For more information about the VGA, see the Dell VxRail™ P670F,
P670N, V670F, and S670 Technical Specifications.
9 USB 3.0 port (1) This port is USB 3.0-compliant.
10 iDRAC dedicated port Enables you to remotely access iDRAC. For more information, see the
iDRAC User's Guide at www.dell.com/poweredgemanuals.
11 System identification
button
Press the system ID button:
●To locate a particular system within a rack.
●To turn the system ID on or off.
To reset iDRAC, press and hold the button for more than 16 s.
●To reset iDRAC using system ID, ensure that the system ID
button is enabled in the iDRAC setup.
●If the system stops responding during POST, press and hold the
system ID button (for more than 5 s) to enter the BIOS progress
mode.
12 OCP NIC port N/A This port supports OCP 3.0. The NIC ports are integrated on the
OCP card which is connected to the system board.
13 NIC port (1,2) The NIC ports are embedded on the LOM card that is connected to
the system board.
14 Power supply unit (PSU 1) For more information about the PSU configurations, see the on
product documentation page.
For more information about supported drives, see the Dell VxRail™ P670F, P670N, V670F, and S670 Technical Specifications.
Inside the system
The following figure and list contains components inside the system:
System overview 13

1. Handle 2. BOSS S2 module bay
3. Riser 1 4. Power supply unit (PSU 1)
5. Riser 2 cage 6. System board
7. Air shroud 8. Cooling fan
9. Drive backplane cover 10. Service tag
11. Cooling fan cage assembly 12. Power supply unit (PSU 2)
13. Riser 3 14. Riser 4
15. Intrusion switch module
The following figure and list contains components inside the system with full length risers and GPU shroud:
14 System overview

1. Handle 2. BOSS S2 module bay
3. Riser 1 4. GPU air shroud top cover
5. GPU air shroud 6. Cooling fan
7. Drive backplane 8. Service tag
9. Cooling fan cage assembly 10. Riser 3
11. Riser 4 12. Intrusion switch module
System overview 15

Initial setup and configuration
Deploy and configure your VxRail.
To install and deploy VxRail, you have the following deployment options:
●You can purchase deployment services from Dell Technologies.
○If you are using VxRail deployment services from Dell Technologies, do not rack the VxRail or connect power.
○Contact your Dell Technologies account team or reseller to arrange for deployment by Dell Technologies certified
technicians.
●Select the VxRail self-deployment option (no installation services). For self-deployment guidance and preparatory
instructions, see KB 187954.
Self deployment
You must have extensive network experience, understanding of VxRail infrastructure planning, and deployment knowledge to
perform a VxRail self-deployment. Go to the VxRail Configuration Portal to perform self deployment.
Contact your sales representative for Dell Technologies Services if you are:
●Uncertain you can complete the end-to-end deployment process
●Unable to complete the deployment.
During the VxRail deployment, iDRAC creates a vxadmin or PTAdmin account. This account provides hardware information to
the VxRail Manager and is required for the VxRail Manager and the cluster to function properly. Do not modify or delete the
vxadmin or PTAdmin account.
CAUTION: If the vxadmin or PTAdmin account is modified or deleted, VxRail Manager and the cluster may not
function properly.
3
16 Initial setup and configuration

Pre-operating system management
applications
You can manage basic settings and features of the VxRail without booting into the operating system by using the system
firmware.
Dell Technologies optimizes your VxRail with the settings during installation and configuration. Do not change any basic settings
or features set by Dell Technologies to ensure best performance.
CAUTION: Performance may be impacted if settings and features configured by Dell Technologies are changed.
Manage the pre-operating system applications
VxRail contains options to manage the pre-operating system applications.
The following options are available:
●System Setup
●Boot Manager
●Dell Lifecycle Controller
●Preboot Execution Environment (PXE)
Your VxRail was optimized by Dell Technologies during the initial configuration. Do not change any of the basic settings or
features set by Dell Technologies to ensure best performance.
iDRAC configuration
The Integrated Dell Remote Access Controller (iDRAC) allows administrators to be more productive and improve the overall
availability of Dell products. iDRAC alerts administrators to issues, perform remote management, and reduce the need for
physical access.
You can log in to iDRAC as the following users:
●iDRAC user
●Microsoft Active Directory user
●LDAP user
If secure default access to iDRAC is used, the iDRAC secure default password is available on the back of the appliance
Information tag. If you have not opted for secure default access to iDRAC, then the default user name and password are root
and calvin. You can also log in by using Dell SSO or Smart Card.
The following prerequisites are a must to log in to iDRAC:
●You must have iDRAC credentials.
●Change the default user name and password after setting up the iDRAC IP address.
The iDRAC IP address is pre-configured for DHCP. This can be changed to a static IP address by logging into iDRAC.
●To access iDRAC, connect the network cable to the Ethernet connector 1 on the system board.
●Change the default username and password after setting up the iDRAC IP address.
Log in to iDRAC
You can log in to iDRAC as the following users:
●iDRAC user
●Microsoft Active Directory user
4
Pre-operating system management applications 17

●LDAP user
If secure default access to iDRAC is used, the iDRAC secure default password is available on the back of the appliance
Information tag. If you have not opted for secure default access to iDRAC, then the default user name and password are root
and calvin. You can also log in by using Dell SSO or Smart Card.
The following prerequisites are a must to log in to iDRAC:
●You must have iDRAC credentials.
●Ensure that you change the default user name and password after setting up the iDRAC IP address.
The iDRAC IP address is pre-configured for DHCP. This can be changed to a static IP address by logging into iDRAC.
●To access iDRAC, connect the network cable to the Ethernet connector 1 on the system board.
●Ensure that you change the default username and password after setting up the iDRAC IP address.
18 Pre-operating system management applications

Replacement of hardware components
You can replace hardware components on your VxRail such as hard disk drives (HDDs), solid-state drives (SSDs), power supply
units.
See the table in the Supported hardware components section to know the components that you can replace. In addition to
these components, there are some hardware components that require you to contact the Dell Technologies support to arrange
for repair or replacement.
Before you proceed with the replacement, go to SolVe and generate the replacement procedure of the component that you
want to replace. For more information about how to use SolVe, see Using SolVe Online for VxRail procedures.
Use SolVe Online for VxRail procedures
To avoid potential data loss, always use SolVe Online for VxRail to generate procedures before you replace any hardware
components or upgrade software.
CAUTION: If you do not use SolVe Online for VxRail to generate procedures to replace hardware components or
perform software upgrades, data loss may occur for VxRail.
You must have a Dell Technologies Support account to use SolVe Online for VxRail.
See KB 124395 for more information about how to use SolVe.
Supported hardware components
Refer to the online support website or SolVe Online for VxRail for hardware-specific information.
The following table contains the not exhaustive list of FRU and CRU components:
Hardware Components Customer Replaceable Unit (CRU) Field Replaceable Unit (FRU)
BOSS S2 Module Yes No
M.2 SSD with BOSS S2 Yes Yes
BOSS S1 Adapter
NOTE: VxRail P670F, P670N, and
V670F supports BOSS S1 adapter.
VxRail S670 does not support
BOSS S1 adapter.
No Yes
M.2 SSD with BOSS S1 No Yes
PCIe Network Interface Cards Yes No
DPU/SmartNIC
NOTE: Applicable only for VxRail
P670N and V670F.
No Yes
Power Supply Unit Yes No
Processor No Yes
Solid State Drive (NVMe) Yes No
Solid State Drive (SAS or SATA) Yes No
Integrated Storage Controller Card
(HBA355i or H755)
Yes No
5
Replacement of hardware components 19

Hardware Components Customer Replaceable Unit (CRU) Field Replaceable Unit (FRU)
GPU Yes No
Air Shroud Yes No
Cooling Fan Module Yes No
System Board No Yes
System Memory Yes No
System Battery Yes No
Left Control Panel Yes No
Right Control Panel Yes No
GPU Air Shroud Yes No
GPU Air Shroud Top Cover Yes No
GPU Air Shroud Filler Yes No
Full Length Expansion Card Riser Yes No
Drive Backplane Cover Yes No
Cooling Fan Cage Assembly Yes No
Side Wall Bracket Yes No
System memory guidelines
The VxRail P670F, P670N, V670F, and S670 supports DDR4 registered DIMMs (RDIMMs), Load Reduced DIMM (LRDIMMs),
and Intel Persistent Memory 200 series (BPS). System memory holds the instructions that are started by the processor.
Your system memory is organized into eight channels per processor (two memory sockets per channel),16 memory sockets per
processor, and 32 memory sockets per system.
The following figure shows the memory channels:
20 Replacement of hardware components