Dell S6000-ON Parts list manual

Dell Networking
S6000-Open Networking (ON)
Getting Started Guide
Publication Date: April 2014
Regulatory Model: S6000

Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use
of your computer.
CAUTION: A CAUTION indicates potential damage to the hardware or loss
of data if you do not follow the instructions.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
____________________
Information in this publication is subject to change without notice.
Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international
copyright and intellectual property laws. Dell and the Dell logo are trademarks of Dell Inc. in the
United States and/or other jurisdictions. All other marks and names mentioned herein may be
trademarks of their respective companies.
Regulatory Model: S6000
2014 - 04 P/N TPN9J Rev. A00

Contents
Contents 1
1 About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . 5
I/O Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Utility Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
After Installing the S6000-ON . . . . . . . . . . . . . . . . . . . . . . 8
System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Unpacking the Switch . . . . . . . . . . . . . . . . . . . . . . . . 11
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . 11
Unpacking Steps . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing an AC Power Supply . . . . . . . . . . . . . . . . . . . . 12
Rack Mount the Switch . . . . . . . . . . . . . . . . . . . . . . . . 13
Rack Mounting Safety Considerations. . . . . . . . . . . . . . 13
Installing the Dell ReadyRails System . . . . . . . . . . . . . . 14
Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . 18
5 Technical Specifications . . . . . . . . . . . . . . . . . . . 21
Chassis Physical Design . . . . . . . . . . . . . . . . . . . . . . . 21
Environmental Parameters . . . . . . . . . . . . . . . . . . . . . . 21
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 22

About this Guide 1
1
About this Guide
This document is intended as a Getting Started Guide to get new systems up and
running and ready for configuration. For complete installation and configuration
information, refer to Installing the S6000-Open Networking (ON) System.

2About this Guide

Introduction 3
2
Introduction
The S6000-ON is a fully featured switch/router one rack unit (RU) system that
you can deploy as a spine, leaf, or top of rack (ToR) device where you require
10Gb and/or 40Gb connections. It contains 32 ports of 40G that you can use to
create a configuration of 96 ports of 10G small form-factor pluggable plus
(SFP+) (using breakout cables) and eight ports of 40G quad small form-factor
pluggable plus (QSFP+).
In a data center network, the S6000-ON switch provides converged network
support and interoperates with Dell Networking and third-party network
devices.
By providing increased 40GbE bandwidth for device interconnection in a shared
network storage environment, with the possibility of splitting 40GbE quad small
form-factor pluggable plus (QSFP+) uplinks into 10GbE SFP+ connections, the
S6000-ON switch is perfectly positioned to help transition a data center with
multiple speed requirements.

4Introduction

Hardware Overview 5
3
Hardware Overview
This section contains information about device characteristics and modular
hardware configurations for the S6000-ON switch.
The S6000-ON has the following physical dimensions:
• 434 x 460 x 43.5 mm (W x D x H).
• 17.09 x 18.11 x 1.71 inches (W x D x H).
The S6000-ON has a chassis design with 1280Gbps switching bandwidth as
listed below:
• 32 port 40G QSFP+
• Up to 96 10G ports with QSFP+ breakout
The system also provides one RS-232 interface RJ-45 console port and a
dedicated Ethernet management port for out-of-band (OOB) management
functions.
The S6000-ON has the following features:
• Supports one universal serial bus (USB-A) port
• Supports one USB-B console port
• Thirty-two 40Gbps QSFP+ ports for 40Gbps transceivers
• On-board high-performance central processing unit (CPU) system with large
memory
• Temperature monitoring
• Software-readable thermal monitor
• Real time clock (RTC) support
• Hot-plugging redundant power supply
• Current monitoring for power management
• Three removable fan modules
• Standard 1U chassis high

6Hardware Overview
I/O Panel
The I/O panel includes:
• Thirty-two fixed QSFP+ ports
• One USB-A 2.0 port
• One USB-B serial console port
• One RS-232 serial console port
• One 10/100/1000BaseT (RJ-45) Ethernet management port
Figure 3-1 shows the S6000-ON I/O panel.
Figure 3-1. S6000-ON I/O Panel
1 - System LED
2 - Thirty-two QSFP+ Ports
3 - Serial Console
4 - Reset
5 - Stack ID
6 - USB-A
7 - USB-B Console
8 - Management
NOTE: The system light emitting diodes (LEDs) are on the I/O panel. The fan tray
power indicators are on the Utility panel.

Hardware Overview 7
Utility Panel
The Utility panel side contains the fan and power modules. Figure 3-2 shows the
S6000-ON power supplies and fan modules.
Figure 3-2. S6000-ON Power Supplies and Fan Modules
1 - Power Supply Unit (PSU) 1
2 - Fan Modules 1-3
3 - PSU 2
Power Supplies
The S6000-ON supports two hot-swappable PSUs. The S6000-ON supports AC
power supplies with two air-flow directions (I/O to PSU and PSU to I/O). Two
PSUs are required for full redundancy, but the system can operate with a single
PSU.
NOTE: If you use a single PSU, install a blank plate in the other PSU slot. Dell
Networking recommends using power supply 2 (PSU2) as the blank plate slot.
The PSUs are field replaceable. When running with full redundancy (two power
supplies installed and running), you can remove and replace one PSU while the
other PSU is running without disrupting traffic.
WARNING: Electrostatic discharge (ESD) damage can occur if components
are mishandled.Always wear an ESD-preventive wrist or heel ground strap
when handling the S6000-ON and its components.

8Hardware Overview
CAUTION: To prevent electrical shock, ensure the S6000-ON is grounded
properly. If you ground your equipment incorrectly, excessive emissions may
result. To ensure the power cables meet your local electrical requirements, use
a qualified electrician.
The power supply LED (on the I/O panel) indicates the power supply status:
• Off - no power
• Solid green - Power supply present and working
For additional LED information, refer to your third-party operating software
documentation.
Fans
The S6000-ON supports three hot-swappable fans that provide cooling for the
system. The S6000-ON has stock keeping units (SKUs) that support the
following configurations. Installation of the fans is done as part of the factory
install based on SKU type. The PSUs are installed at the customer site (refer to
Power Supplies ).
• AC PSU with fan airflow from I/O to PSU
• AC PSU with fan airflow from PSU to I/O
All fans and PSUs in a configuration must be in the same airflow direction.
The S6000-ON supports three fan trays with airflow directions from I/O to
Utility or Utility to I/O. The PSU airflow directions are indicated with stickers
on PSUs.
After Installing the S6000-ON
After you have securely installed and powered on the S6000-ON, to configure
your system, refer to your ONIE-compatible third-party operating system
documentation.
System Status
You can view S6000-ON status information using the system LEDs.

Hardware Overview 9
As shown in Figure 3-3 , the S6000-ON includes LED displays on both the I/O
and PSU side of the chassis.
Figure 3-3. S6000-ON PSU and Fan Tray LEDs
1- Fan Tray 1-3 LEDs
2 - PSU 1-2 LEDs

10 Hardware Overview
1 - Serial Console
2 - Master LED
3 - Power LED
4 - Fan Status LED
5 - Locator LED
6 - Stack ID
7 - USB-A
8 - USB-B Console
9 - Management
For LED information, refer to your third-party operating software
documentation.

Installation 11
4
Installation
Unpacking the Switch
This section describes the package contents and the steps to unpack the S6000-
ON switch.
Package Contents
When unpacking each switch, make sure that the following items are included:
• One S6000-ON switch
• One RJ-45 to DB-9 female cable
• Two sets of rail kits (no tools required)
• Two PSUs
• One AC power cord (country/region specific)
• Getting Started Guide
• Safety and Regulatory Information
• Warranty and Support Information
• Software License Agreement
Unpacking Steps
NOTE: Before unpacking the switch, inspect the container and immediately report
any evidence of damage.
Step Task
1 Place the container on a clean, flat surface and cut all straps securing the container.
2 Open the container or remove the container top.
3 Carefully remove the switch from the container and place it on a secure and clean
surface.
4 Remove all packing material.
5 Inspect the product and accessories for damage.

12 Installation
Installing an AC Power Supply
To install an AC power supply, follow these steps.
NOTE: The PSU slides into the slot smoothly. Do not force the PSU into a slot as
this may damage the PSU or the S6000-ON chassis.
NOTE: Ensure that the PSU is correctly installed. When the PSU is correctly
installed, the power connector is on the left side of the PSU and the status LED is at
the bottom of the PSU.
NOTE: If you use a single PSU, install a blank plate in the other PSU slot. Dell
Networking recommends using power supply 2 (PSU2) as the blank plate slot.
Step Task
1Remove the PSU slot cover from the S6000-ON (the PSU side of switch). You
may select either of the two PSU slots.
2Remove the PSU from the electro-static bag.
3Insert the PSU into the switch PSU slot (insert the PSU exposed PCB edge
connector first).
The PSU slot is keyed such that the PSU can only be fully inserted in one
orientation.
1 - PSU
2 - Slot
When the PSU is installed correctly, it snaps into place and is flushed with the
back of the switch.

Installation 13
NOTE: The system powers up as soon as the cables are connected between the
power supply and the power source.
Rack Mount the Switch
You may either place the switch on the rack shelf or mount the switch directly
into a 19" wide, EIA-310-E-compliant rack (four-post, two-post, or threaded
methods). The Dell ReadyRails™ system is provided for 1U front-rack and
two-post installations. The ReadyRails system includes two separately packaged
rail assemblies and two rails that are shipped attached to the sides of the switch.
WARNING: This is a condensed reference. Read the safety instructions in your
Safety, Environmental, and Regulatory information booklet before you begin.
CAUTION: Do not use the mounted Ready-Rails as a shelf or a workplace.
NOTE: The illustrations in this document are not intended to represent a specific
switch.
Rack Mounting Safety Considerations
• Rack loading — Overloading or uneven loading of racks may result in shelf
or rack failure, causing damage to the equipment and possible personal
injury. Stabilize racks in a permanent location before loading begins. Mount
the components beginning at the bottom of the rack, then work to the top.
Do not exceed your rack load rating.
• Power considerations — Connect only to the power source specified on the
unit. When you install multiple electrical components in a rack, ensure that
the total component power ratings do not exceed the circuit capabilities.
Overloaded power sources and extension cords present fire and shock
hazards.
4Plug in the appropriate cord (AC three prong) from the switch PSU to the
external power source (an AC wall outlet).
5If you have a redundant PSU (a second PSU), repeat steps 1 through 4 using the
second PSU slot on the S6000-ON switch.
Step Task (continued)

14 Installation
• Elevated ambient temperature — If you install the equipment in a closed rack
assembly, the operating temperature of the rack environment may be greater
than the room ambient temperature. Use care not to exceed the 40 ° C
maximum ambient temperature of the switch.
• Reduced air flow — Install the equipment in the rack so that you do not
compromise the amount of airflow required for safe operation of the
equipment.
• Reliable earthing — Maintain reliable earthing of rack-mounted equipment.
Pay particular attention to the supply connections other than the direct
connections to the branch circuit; for example, use of power strips.
• Do not mount the equipment with the rear panel facing in the downward
position.
Installing the Dell ReadyRails System
The ReadyRails rack mounting system is provided to easily configure your rack
so that you can install your switch. Install the ReadyRails system using the 1U
tool-less method or one of three possible 1U tooled methods (two-post flush
mount, two-post center mount, or four-post threaded).
1U Tool-less Configuration (Four-Post Square Hole or Unthreaded Round Hole):
1 With the ReadyRails flange ears facing outward, place one rail between the
left and right vertical posts.Align and seat the rear flange rail pegs in the rear
vertical post flange. In Figure 4-1, item 1 shows how the pegs appear in both
the square and unthreaded round holes.

Installation 15
Figure 4-1. 1U Tool-less Configuration
2 Align and seat the front flange pegs in the holes on the front side of the
vertical post. Refer to Figure 4-1, item 2.
3 Repeat this procedure for the second rail.
4 To remove each rail, pull on the latch release button on each flange ear and
unseat each rail. Refer to Figure 4-1, item 3.

16 Installation
Two-Post Flush-Mount Configuration:
1 For this configuration, remove the castings from the front side of each
ReadyRails assembly. Refer to Figure 4-2, item 1. Use a Torx driver to
remove the two screws from each front flange ear (on the switch side of the
rail) and remove each casting. Retain the castings for future rack
requirements. It is not necessary to remove the rear flange castings.
Figure 4-2. Two-Post Flush-Mount Configuration
2 Attach one rail to the front post flange with two user-supplied screws. Refer
to Figure 4-2, item 2.
3 Slide the plunger bracket forward against the vertical post and secure the
plunger bracket to the post flange with two user-supplied screws. Refer
to Figure 4-2, item 3.
4 Repeat this procedure for the second rail.

Installation 17
Two-Post Center-Mount Configuration:
1 Slide the plunger bracket rearward until it clicks into place and secure the
bracket to the front post flange with two user-supplied screws. Refer
to Figure 4-3, item 1.
Figure 4-3. Two-Post Center-Mount Configuration
2 Slide the back bracket towards the post and secure it to the post flange with
two user-supplied screws. Refer to Figure 4-3, item 2.
3 Repeat this procedure for the second rail.
Four-Post Threaded Configuration:
1 For this configuration, remove the flange ear castings from each end of the
ReadyRails assemblies. Use a Torx driver to remove the two screws from
each flange ear and remove each casting. Refer to Figure 4-4, item 1. Retain
the castings for future rack requirements.
2 For each rail, attach the front and rear flanges to the post flanges with two
user-supplied screws at each end. Refer to Figure 4-4, item 2.