Dell 3115CN User manual

Dell 3115cn
Service Manual
23 Mar 2009

Information in this document is subject to change without notice.
2010 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc.is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to the entities claiming the marks and
names of their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than
its own.

Version record
Version recordVersion record
Version record
Refer to the portion indicated by change bar in each section.
Also refer to the reasons in table below.
Version Issue date Note
1st November 28, 2006 1st issued
2nd
March 20, 2007
2
nd
version issued
Section 1, FIP
The contents were improved.
Section 2, Operation of Diagnostic
The contents were improved.
Section 3, RRP
The contents were improved.
Section 4, P/J Locations
The contents were improved.
Section 5, Parts List
The contents were improved.
Section 7, Wiring
The contents were improved.
Section 8, Specifications
The contents were improved.
3rd
March 23, 2009
3rd version issued
Section 5, Parts List
The contents were improved.

i
Version 2 2007.03.20
Cautions
Operation contents of this document may be subject to modification without notice.
Dell Inc. will not assume responsibility for accidental or incidental damages resulting from technical
or editorial errors or omissions in this manual, the issue of this manual, the execution of descriptions
in this manual, or the use of this manual.
This document is protected by copyright. Do not photocopy or duplicate any part of this document in
any form without written permission from Dell Inc.

ii
Version 2 2007.03.20
1. About this manual
This manual is a standard service manual of Dell Inc. containing information required for maintenance
of this laser printer (standard specifications).
2. Marks giving caution
Maintenance operations requiring special cautions or additional information regarding descriptions in
this manual are presented as "Warning," "Caution," or "Note," depending on their nature.
If instructions are not observed, death or serious injury may result.
If instructions are not observed, injuries to workers or physical damage to assets
(including this laser printer) may result.
Essentials for procedures, steps, rules, and others.
Reference Incidental information to descriptions.
3. Related documents
-Instruction manuals (standard manuals)
Describe the operation and handling of this laser printer.
-Performance specifications
Describe in detail various specifications of this laser printer.
(In the event of a discrepancy between this manual and the performance specifications, the
performance specifications take precedence.)
-Spare parts list
Information on maintenance parts (spare parts) for this laser printer.

iii
Version 2 2007.03.20
4. Safety
To prevent possible accidents during maintenance operation, you should observe strictly the "Warning"
and "Caution" information in this manual.
Avoid dangerous operations and operations out of the scope of this manual.
Various processes not covered by this manual may be required in actual operations, and should be
performed carefully, always giving attention to safety.
4.1 Power source
Keep the power plug disconnected during the maintenance operation to prevent electric shock, burns
and other damages.
If the power supply should be kept connected to measure voltage or for other similar reasons, take
sufficient care to prevent electric shock, by following the procedures in this manual.
While the printer is on, never touch live parts if not required.
Power is supplied to the power switch / inlet even while the printer is off. Never
touch its live components.
Do not touch live parts unless otherwise specified.
Gnb00002KB

iv
Version 2 2007.03.20
4.2 Driving units
When servicing gears or other driving units, be sure to turn them OFF and plug off. Drive them
manually when required.
Never touch the gears or other driving units while the printer is running.
4.3 High-temperature units
When servicing high-temperature units (securing unit, etc.), be sure to turn them off to prevent burns,
injuries and other troubles. Remove the power plug and start service processes after they have cooled
down sufficiently.
Because high-temperature units are still hot after they complete an operation, wait
at least 40 minutes before starting maintenance service.

v
Version 1 2006.11.21
4.4 Battery
Lithium Battery is used in the following component.
- PWBA HYUI
There is a danger of a new battery exploding if it is incorrectly installed.
Replace the battery only with the same or equivalent type recommended by the
manufacturer.
Dispose the battery according to the manufacturer’s instruction.
Gnb00011KA
PWBA HYUI

vi
Version 2 2007.03.20
4.5 Laser beams
• If your eyes are exposed to laser beams, you may lose your eyesight.
• Never open the cover if the warning label for laser beams is attached there.
• Before disassembling and reassembling this laser printer, be sure to turn it OFF.
• When servicing this laser printer while it is running, be sure to follow the
procedures specified in this manual.
• You should be well aware that the laser beams are capable of injuring you and
other people near the printer.
Laser beams have features as follows:
• Frequencies are smaller in width than other beams (sun and electric bulbs) and
phases are uniform so that high monochromatic and convergence performance
can be obtained and thin beams of light can reach places at a long distance.
• Being highly converged, the laser beams exert a heating action that may be
harmful to human body.
Reference: The laser beams of this laser printer are invisible rays.
Gnb00003KA
PRINT HEAD

vii
Version 2 2007.03.20
4.6 Warning/caution labels
Warning labels and caution labels are attached to this laser printer to prevent accidents Check those
labels for their peeling or stains when servicing the printer.
4.6.1 Caution label for high-temperature units
Gnb00004KA