Dell PowerEdge C5230 User manual

www.dell.com | support.dell.com
Dell PowerEdge C5230
Getting Started
With Your
System
Mise en route de votre système
Introdução ao uso do sistema
Introducción al sistema
KTTDFA00.book Page 1 Thursday, September 26, 2013 11:31 PM

KTTDFA00.book Page 2 Thursday, September 26, 2013 11:31 PM

www.dell.com | support.dell.com
Dell PowerEdge C5230
Getting Started
With Your
System
Regulatory Model B04S
KTTDFA00.book Page 1 Thursday, September 26, 2013 11:31 PM

Notes, Cautions, and Warnings
____________________
© 2013 Dell Inc.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.
Intel
®
andIntel
®
Xeon
®
areregisteredtrademarksofIntelCorporationintheU.S.andothercountries.
Microsoft
®
and Windows
®
are either trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries. Red Hat
®
and Red Hat Enterprise Linux
®
are registered
trademarks of Red Hat, Inc. in the United States and/or other countries. SUSE™ is a trademark of
Novell Inc. in the United States and other countries. Citrix
®
, Xen
®
, and XenServer
®
are either
registeredtrademarksortrademarksofCitrixSystems,Inc.intheUnited Statesand/orothercountries.
VMware
®
is a registered trademarks or trademarks of VMWare, Inc. in the United States or other
countries.
Regulatory Model B04S
2013 - 09 P/N KTTDF Rev. A00
NOTE: A NOTE indicates important information that helps you make better use of
your system.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
KTTDFA00.book Page 2 Thursday, September 26, 2013 11:31 PM

Installation and Configuration 3
This server is intended for installation only in restricted access locations as
defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions
apply:
• Access can only be gained by service persons or by users who have been
instructed about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
• Access is through the use of a tool or lock and key, or other means of
security, and is controlled by the authority responsible for the location.
Installation and Configuration
Unpacking the System
Unpack your system and identify each item.
Installing the Tool-Less Rail Solution
CAUTION: Restricted Access Location
WARNING: Before performing the following procedure, review and follow the
safety instructions that came with the system.
WARNING: Whenever you need to lift the system, get others to assist you. To
avoid injury, do not attempt to lift the system by yourself.
WARNING: The system is not fixed to the rack or mounted on the rails. To avoid
personal injury or damage to the system, you must adequately support the system
during installation and removal.
WARNING: To avoid a potential electrical shock hazard, a third wire safety
grounding conductor is necessary for the rack installation. The rack equipment
must provide sufficient airflow to the system to maintain proper cooling.
CAUTION: When installing rails in a square-hole rack it is important to ensure
that the square peg slides through the square holes.
CAUTION: Square studs must be flush with the rack posts to install properly.
KTTDFA00.book Page 3 Thursday, September 26, 2013 11:31 PM

4 Installation and Configuration
1 Pull on the latch release buttons on the end piece midpoints to open the
rail latches.
Figure 1-1. Unlocking the Rail Latches
2 Align the end pieces of the rails on the vertical rack flanges to seat the pegs
in the bottom hole of the first U and the top hole of the second U. Engage
the back end of the rail until the latch locks in place.
Figure 1-2. Aligning the Rails on the Rack
3 Repeat steps 1 and 2 to position and seat the front end piece on the
vertical flange.
NOTE: The rails can be used in both square-hole and round-hole racks.
NOTE: To remove the rails, pull on the latch release button on the end piece
midpoint and unseat each rail.
Front
Back
KTTDFA00.book Page 4 Thursday, September 26, 2013 11:31 PM

Installation and Configuration 5
Installing the System
Empting the System Chassis
1 Unplug the power cable from the power supply unit.
Figure 1-3. Unplugging the Power Cable from the Power Supply Unit
2 Pull out the power supply unit handle.
Figure 1-4. Releasing the Power Supply Unit Handle
3 Press down on the release latch  .
WARNING: Before installation, it is recommended that you remove the sleds and
power supplies from the system to reduce weight.
KTTDFA00.book Page 5 Thursday, September 26, 2013 11:31 PM

6 Installation and Configuration
4 Pull the power supply unit out of the system  .
Figure 1-5. Removing the Power Supply Unit
5 Press the release latch down  .
6 Pull the sled out of the system  .
Figure 1-6. Removing the Sled
KTTDFA00.book Page 6 Thursday, September 26, 2013 11:31 PM

Installation and Configuration 7
Installing the System Into the Rack
1 Slide the system into the rack.
2 If present, remove the chassis stabilizer shipping bracket (optional) from
the rack.
3 Tighten the captive thumbscrews to secure the ears of the system to the
front of the rack.
Figure 1-7. Securing the Chassis on the Rails
WARNING: Whenever you need to lift the system, get others to assist you. To
avoid injury, do not attempt to lift the system by yourself.
NOTE: To transport systems already installed in the rack, ensure that the two
chassis stabilizer shipping brackets (optional) are in place.
NOTE: Make sure the latch release mechanism is engaged correctly.
KTTDFA00.book Page 7 Thursday, September 26, 2013 11:31 PM

8 Installation and Configuration
Populating the System
1 Push the power supply unit into the system until flush with the case and
the release latch locks.
Figure 1-8. Installing the Power Supply Unit
2 Close the power supply unit handle.
Figure 1-9. Securing the Power Supply Unit Handle
3 Plug the chassis power cable into the power supply unit.
KTTDFA00.book Page 8 Thursday, September 26, 2013 11:31 PM