Dell Data Domain DD9800 User manual

Dell EMC Data Domain DD9800 System
Installation and Storage Expansion Guide
September 2022
Rev. 04

Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2021 - 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Other trademarks may be trademarks of their respective owners.

Figures..........................................................................................................................................5
Tables........................................................................................................................................... 7
Chapter 1: Introduction and Preparation........................................................................................8
Document purpose.............................................................................................................................................................. 8
Tools and supplies needed.................................................................................................................................................8
Safety information...............................................................................................................................................................9
Working with a portable lift............................................................................................................................................. 10
Adjusting the arms for a frontal lift......................................................................................................................... 10
Reconfiguring the lift with the Voyager kit............................................................................................................ 11
Chapter 2: Install the System in the Rack.................................................................................... 13
Unpack the system............................................................................................................................................................ 13
Install the rack brackets................................................................................................................................................... 13
Shelf brackets and cable management assembly.................................................................................................13
Install rail brackets on the Data Domain racks (for square or round hole racks)......................................... 15
Install rail brackets using the adapter hardware (for threaded hole racks)...................................................17
Install the DD9800 system into a rack..........................................................................................................................19
Mount the cable management assembly..................................................................................................................... 22
Install the Data Domain cable management assembly........................................................................................23
Installing the expansion shelves into the racks.......................................................................................................... 24
Chapter 3: Install the Disk Shelves in the Rack............................................................................ 25
Remove filler panels..........................................................................................................................................................25
Install an ES30 or FS15 shelf into the rack................................................................................................................. 25
Racking and cabling.................................................................................................................................................... 25
Rail kit.............................................................................................................................................................................26
Installing the rails in the cabinet.............................................................................................................................. 26
Adjusting for various rack types...............................................................................................................................27
Installing the rails using the adapter hardware.....................................................................................................27
Installing the shelf on the rails..................................................................................................................................29
Install a DS60 shelf into the rack.................................................................................................................................. 30
Installing rails................................................................................................................................................................. 31
Installing the shelf onto the rails..............................................................................................................................34
Inserting and securing the top cover and shelf....................................................................................................36
1U cable management tray installation (underneath).........................................................................................39
Chapter 4: Connect Cables and Power On................................................................................... 53
Connecting the expansion shelves and the controllers........................................................................................... 54
ES30 cable information....................................................................................................................................................54
Connecting multiple ES30 shelves to the DD9800 system.................................................................................... 57
DD9800.......................................................................................................................................................................... 57
DD9800 with HA (one rack).....................................................................................................................................59
DD9800 with HA (two racks)...................................................................................................................................60
Contents
Contents 3

DD9800 with DD Cloud Tier (Single node or HA)............................................................................................... 62
DD9800 with ERSO.................................................................................................................................................... 64
DS60 cable information....................................................................................................................................................67
Connecting multiple DS60 shelves to the DD9800 system.................................................................................... 68
DD9800..........................................................................................................................................................................68
DD9800 with HA..........................................................................................................................................................69
DD9800 with DD Cloud Tier (Single node)........................................................................................................... 72
DD9800 with DD Cloud Tier (HA)........................................................................................................................... 73
DD9800 with ERSO.................................................................................................................................................... 75
Connecting the HA interconnect................................................................................................................................... 77
Connect data cables on both nodes............................................................................................................................. 78
Power on the systems......................................................................................................................................................78
Install the bezel..................................................................................................................................................................80
Chapter 5: Configure System for Use.......................................................................................... 81
Enable administrative communication...........................................................................................................................81
Accepting the End User License Agreement..............................................................................................................82
Run the configuration wizard......................................................................................................................................... 83
Configuring the network............................................................................................................................................83
Configuring additional system parameters..................................................................................................................84
Configure HA for new installations............................................................................................................................... 85
Appendix A: Add Storage Capacity.............................................................................................. 88
Prepare system for storage expansion........................................................................................................................ 88
Add Cache Tier storage................................................................................................................................................... 88
Install and connect the new storage............................................................................................................................. 91
Power cycle DS60 shelves.........................................................................................................................................91
Add a new disk pack to an existing DS60................................................................................................................... 92
Locate the target enclosure in the rack................................................................................................................ 92
Identify the first empty disk pack in the target enclosure................................................................................ 92
Opening the console................................................................................................................................................... 93
Removing the front bezel..........................................................................................................................................93
Pulling the shelf chassis out..................................................................................................................................... 94
Add new disks.............................................................................................................................................................. 95
Close the shelf chassis...............................................................................................................................................95
Verify and configure the new disks.............................................................................................................................. 96
License the new storage with electronic licensing................................................................................................... 99
Expand the file system................................................................................................................................................... 100
4Contents

1 Warning about lifting the system......................................................................................................................... 10
2 Adjusting the lift arm bar to just under 17 inches..............................................................................................11
3 Reconfiguring the portable lift with the Voyager conversion kit.................................................................. 12
4 Warning about lifting the system..........................................................................................................................13
5 Rail bracket inside.....................................................................................................................................................14
6 Rail bracket outside..................................................................................................................................................14
7 Cable management assembly (CMA).................................................................................................................. 15
8 Insert screw in the back......................................................................................................................................... 16
9 Insert screw in the front.........................................................................................................................................16
10 Attach bracket to front of rack.............................................................................................................................17
11 Adapters..................................................................................................................................................................... 18
12 Attaching the front rail with the screw...............................................................................................................18
13 Attach front rail adapter......................................................................................................................................... 19
14 Warning about lifting the system.........................................................................................................................20
15 System on a rack..................................................................................................................................................... 20
16 Location of serial number tag............................................................................................................................... 22
17 Data Domain CMA back......................................................................................................................................... 23
18 Data Domain cable management assembly back inside..................................................................................23
19 Rear of the rack mount rail....................................................................................................................................24
20 Holes for alignment pins.........................................................................................................................................26
21 Installing the rails..................................................................................................................................................... 26
22 Attaching the rail to the rack................................................................................................................................29
23 Sliding the enclosure onto the rails..................................................................................................................... 29
24 Rail tabs securing the rear of the enclosure..................................................................................................... 30
25 Securing the front of the enclosure....................................................................................................................30
26 Rail installation.......................................................................................................................................................... 32
27 Installing the right rail to the rear channel.........................................................................................................33
28 Installing the right rail to the front channel.......................................................................................................33
29 Sliding the shelf chassis into the rails.................................................................................................................35
30 Unlocking the casters............................................................................................................................................. 35
31 Locking the casters................................................................................................................................................. 36
32 Removing the straps............................................................................................................................................... 36
33 Inserting and securing the shelf to the cabinet (shoulder screw configuration)..................................... 37
34 Removing semi-captive screws............................................................................................................................38
35 Installing ears to rack using truss head screws................................................................................................38
36 Installing top cover using truss head screws (shelf and rack not shown).................................................38
37 Removal of semi-captive screws......................................................................................................................... 39
38 Blue tab on rail must be pushed in...................................................................................................................... 40
39 Installing and securing the rails—front............................................................................................................... 41
40 Installing and securing the rails—rear................................................................................................................. 41
Figures
Figures 5

41 Installing tray............................................................................................................................................................. 41
42 Spring clips—push up to release tray.................................................................................................................42
43 Opening the cable chain lids................................................................................................................................. 42
44 Cable positioning in cable chains..........................................................................................................................42
45 1-Inch graduation label............................................................................................................................................43
46 Attaching cable chains to tray.............................................................................................................................. 43
47 Installing the chassis bracket into the shelf...................................................................................................... 43
48 Installing the chassis bracket................................................................................................................................ 44
49 Installing the bezel................................................................................................................................................... 44
50 Screw and nut placements....................................................................................................................................45
51 18"-22" marking........................................................................................................................................................46
52 26"-30" Marking.......................................................................................................................................................46
53 30"-34" Marking.......................................................................................................................................................47
54 Rail installation..........................................................................................................................................................48
55 Removing shipping tape......................................................................................................................................... 49
56 Securing a rail with a single screw...................................................................................................................... 50
57 Location of securing screws and alignment pins............................................................................................. 50
58 Nutbar installation (Left nutbar shown)............................................................................................................. 51
59 Node 0 SAS I/O module to ES30 host port connector..................................................................................54
60 Node 1 SAS I/O module to ES30 expansion port connector........................................................................ 55
61 Cables for ES30 to ES30 connections............................................................................................................... 56
62 DD9800 with ES30 shelves...................................................................................................................................58
63 DD9800 with ES30 shelves, HA (one rack)......................................................................................................60
64 DD9800 with ES30 shelves, HA (two racks)....................................................................................................62
65 DD9800 with ES30 shelves, DD Cloud Tier or HA and DD Cloud Tier....................................................... 64
66 DD9800 with ES30 shelves, ERSO..................................................................................................................... 66
67 SAS I/O module to DS60 connector...................................................................................................................67
68 DD9800 with DS60 shelves.................................................................................................................................. 69
69 DD9800 with DS60 shelves, HA........................................................................................................................... 71
70 DD9800 with DS60 shelves, DD Cloud Tier...................................................................................................... 73
71 DD9800 with DS60 shelves, HA and DD Cloud Tier....................................................................................... 75
72 DD9800 with DS60 shelves, ERSO..................................................................................................................... 77
73 DD9800 HA interconnect.......................................................................................................................................78
74 Power LED and power button.............................................................................................................................. 82
75 Removing a disk filler module............................................................................................................................... 89
76 Installing a disk......................................................................................................................................................... 90
77 Opening the console............................................................................................................................................... 93
78 Removing the front bezel...................................................................................................................................... 94
79 Pulling the Chassis Out (Two shoulder Screw Configuration)..................................................................... 94
80 Installing a disk......................................................................................................................................................... 95
6 Figures

1 rail kit.......................................................................................................................................................................... 26
2 Pins for third-party racks....................................................................................................................................... 31
3 Truss head screws................................................................................................................................................... 37
4 Pins for third-party racks.......................................................................................................................................47
5 Parts list..................................................................................................................................................................... 48
6 Parts list.....................................................................................................................................................................50
7 List of parts used in nutbar installation illustration.......................................................................................... 51
8 Cables for node 0 to ES30 shelf loop.................................................................................................................55
9 Cables for node 1 to ES30 shelf loop..................................................................................................................55
10 ES30 to ES30 cable options................................................................................................................................. 56
11 DD9800 with ES30..................................................................................................................................................57
12 DD9800 with ES30 HA primary node cabling instructions (one rack)....................................................... 59
13 DD9800 with ES30 HA standby node cabling instructions (one rack)...................................................... 59
14 DD9800 with ES30 HA primary node cabling instructions (two racks)..................................................... 60
15 DD9800 with ES30 HA standby node cabling instructions (two racks)..................................................... 61
16 DD9800 with ES30 DD Cloud Tier or HA and DD Cloud Tier primary node cabling instructions.........62
17 DD9800 with ES30 DD Cloud Tier or HA and DD Cloud Tier standby node cabling instructions........ 63
18 DD9800 with ES30 ERSO..................................................................................................................................... 64
19 Cables for node 0 and node 1 to DS60 shelf loop............................................................................................67
20 DD9800 with DS60................................................................................................................................................. 68
21 DD9800 with DS60 HA primary node cabling instructions............................................................................70
22 DD9800 with DS60 HA standby node cabling instructions........................................................................... 70
23 DD9800 with DS60 DD Cloud Tier...................................................................................................................... 72
24 DD9800 with DS60 HA and DD Cloud Tier primary node cabling instructions......................................... 74
25 DD9800 with DS60 HA and DD Cloud Tier standby node cabling instructions........................................ 74
26 DD9800 with DS60 ERSO cabling instructions................................................................................................ 76
27 Communications settings....................................................................................................................................... 81
Tables
Tables 7

Introduction and Preparation
Topics:
•Document purpose
•Tools and supplies needed
•Safety information
•Working with a portable lift
Document purpose
This installation guide provides instructions for installing the hardware associated with PowerProtect systems. Systems are
shipped to the customer site either pre-installed in a rack (factory-racked) or as separate components to install in an existing
rack at the site (field-installed). This guide provides instructions for both types of installation.
This document is intended for customers or Dell EMC Support personnel who are qualified to install PowerProtect systems.
Field-installed systems
To install PowerProtect systems in an existing rack at the customer site, follow all the instructions in this document to rack,
cable, and configure the system.
Factory-racked systems
Factory-racked systems are pre-installed in the rack with the cables already connected. Follow the instructions in Configure
System for Use on page 81 to configure factory-racked systems.
The following documents, available from the Online Support website, provide additional information about factory-racked
systems:
●Dell EMC 40U-P Cabinet Site Preparation Guide
●Dell EMC 40U-P Cabinet Unpacking and Setup Guide
●Dell EMC Titan S Site Preparation Guide
●Dell EMC Titan S Unpacking and Setup Guide
●Dell EMC Data Domain Rack Service Guide
Tools and supplies needed
These tools and supplies may be helpful for the installation and setup tasks for Data Domain systems.
●Null modem cable (DB-9 female to female), plus spare
●USB-to-DB-9 serial (male connector) converter cable if the laptop does not have a serial port, plus spare
●Power adapter, C13 to NEMA 5–15 (if based in North America), or a power cord for your laptop power adapter with a C13
plug, so that you can power your laptop from a rack PDU
●Antistatic wrist strap and conductive foam pad
●Screwdrivers:
○Phillips #2 with a 12 in. or longer blade
○Phillips #2 (standard-length blade)
○Phillips #1
○Flat head 3/16 in.
○Flat head 1/4 in.
1
8 Introduction and Preparation

○Torx T10
●Flashlight
●Needle nose pliers
●Diagonal wire cutters (for cutting tie wraps)
●2 GB or greater USB flash memory drive
●Tie wraps (4 in. and 8 in.)
●(recommended) Roll of 5/8 inch Velcro cable tie material (3M Scotchmate SJ-3401 or similar)
Safety information
CAUTION:
●If the system is used in a manner not specified by the manufacturer, the protection provided by the
equipment may be impaired.
●The RJ45 sockets on the motherboard, PCI cards, or I/O modules are for Ethernet connection only and must
not be connected to a telecommunications network.
Review this list of important safety recommendations.
●All plug-in modules and blank plates are part of the fire enclosure and must be removed only when a replacement can be
added immediately. The system must not be run without all parts in place.
●A DD9800 system must be operated only from a power supply input voltage range of 200–240 VAC and 50–60 Hz. ES30
shelves use 100-240 VAC and 50–60 Hz. DS60 shelves use 200–240 VAC and 50–60 Hz.
●Each component is intended to operate with all working power supplies installed.
●Provide a suitable power source with electrical overload protection.
●A safe electrical earth connection must be provided to each power cord. Check the grounding of the power sources before
applying power.
●The plug on each power supply cord is used as the main device to disconnect power from the system. Ensure that the
socket outlets are located near the equipment and are easily accessible.
●Permanently unplug the unit if you think it is damaged in any way and before moving the system. A DD9800 system includes
four power supplies. To completely remove system power, you must disconnect all four power supplies.
●The power connections must always be disconnected prior to removal or replacement of a power supply module from any of
the components in the system.
●A faulty power supply module must be replaced within 24 hours.
●Do not lift system components by yourself. A DD9800 system weighs up to 117 lbs (53.2 kg), an ES30 expansion shelf
weighs up to 68 lbs (30.8 kg), and a DS60 shelf weighs up to 225 lbs (90.7 kg).
CAUTION: Data Domain systems are heavy. Use at least two people or a mechanical lift to move any system.
●Do not lift an expansion shelf by the handles on any modules. The handles are not designed to support the weight of the
populated shelf.
●To comply with applicable safety, emission, and thermal requirements, covers must not be removed and all bays must be
fitted with plug-in modules.
●Once removed from the shipping box, it is ok to lift the DD9800 system or the chassis with the four handles to place in a
rack. You will need to remove the handles from the sides before sliding the system in the rack. The four handles should be
saved for later use.
Introduction and Preparation 9

Figure 1. Warning about lifting the system
●Load the rack with storage shelves beginning at the bottom and the DD9800 system in the designated location to prevent
the rack from becoming top-heavy.
●For ESD protection, Data Domain recommends that you wear a suitable antistatic wrist or ankle strap. Observe all
conventional ESD precautions when handling plug-in modules and components.
●Do not extend components on slide rails until you have loaded at least three or more similarly weighted items in the rack, or
unless the rack is bolted to the floor or overhead structure to prevent tipping.
Working with a portable lift
If you are installing the shelf with all field replaceable units (FRUs) removed, you can install the shelf without using a lift. If you
need to install the shelf with FRUs onboard, use a portable lift.
Service personnel generally use the portable lift manufactured by Alum-A-Lift. Instructions for this lift are included in the lift kit.
NOTE: If you are using a portable lift other than the Alum-A-Lift, adapt these instructions as necessary while following all
required safety requirements.
Lift requirements
For installations in racks that are 28U (49 inches) or less above the floor, use the lower mast, which is rated for 400 pounds.
For installations in racks that are more than 28U (49 inches) above the floor, use the lower mast configuration and a support
table with the "Voyager" conversion kit, which is rated for 225 pounds.
Adjusting the arms for a frontal lift
About this task
If you plan to use the mechanical lift directly in front of the cabinet, adjust the width of the lift arm/tray to just under 17 inches
to ensure that the arms will stay under the chassis.
Steps
1. Adjust the two arms with rollers so that they are 17 inches apart measured from the outside edges.
2. Tighten the arms to secure them.
The following figure shows an example of adjusting the lift arm/tray to just under 17 inches.
10 Introduction and Preparation

1
2<17”
CL4900
Figure 2. Adjusting the lift arm bar to just under 17 inches
Reconfiguring the lift with the Voyager kit
About this task
If you are using the Alum-A-Lift to install or remove components above 49 inches (28U) from the floor, use the single (lower)
mast configuration with the Voyager conversion kit and support table.
Steps
1. Unpack the Voyager kit.
2. Use the instructions provided within the kit to reconfigure the lift.
Introduction and Preparation 11

CL5422
1 2
Figure 3. Reconfiguring the portable lift with the Voyager conversion kit
12 Introduction and Preparation

Install the System in the Rack
CAUTION: Improper installation on the rails may damage the rails or cause the system to fall when extended.
When extending the system from the rack, pull outward slowly and verify the system is properly installed on the
rails.
Topics:
•Unpack the system
•Install the rack brackets
•Install the DD9800 system into a rack
•Mount the cable management assembly
•Installing the expansion shelves into the racks
Unpack the system
1. Remove the accessories and rail mount kit from the shipping packages.
2. Remove the controller and the bezels from the shipping packages.
NOTE: For field installations, the controller has temporary handles pre-fitted at the factory to help in removal of the
system from the box and for placing it in a rack. While the controller is being placed in a rack, the handles attached to
the chassis can be removed by loosening the thumbscrew on each handle. The handles must be saved for future use.
CAUTION: Data Domain systems are heavy. Always use two people or a mechanical lift to move a system. The
chassis displays warning labels.
Figure 4. Warning about lifting the system
3. Remove expansion shelves and their bezels from the shipping packages.
Install the rack brackets
Data Domain systems are installed into racks using the rail bracket hardware.
Shelf brackets and cable management assembly
The rack mounting kits are compatible with racks that have front-to-rear post spacing between 24 inches and 36 inches. The
hardware fits the following types of mounting holes:
2
Install the System in the Rack 13

●7.1 mm round holes
●.375 inch / 9.2 mm square holes
●M5, M6, 12-24, and 10-32 threaded holes
The controller rail kit includes the following items:
●Two bracket assemblies, one marked for the left side and one marked for the right side of the rack
Figure 5. Rail bracket inside
1. Left inside bracket
2. Right inside bracket
Figure 6. Rail bracket outside
1. Left outside bracket
2. Right outside bracket
A cable management assembly (CMA), for organization of cables at the rear of the system, is already installed onto the DD9800
system on a Data Domain rack. For field installed systems, the CMA is shipped with the DD9800 system.
14 Install the System in the Rack

Figure 7. Cable management assembly (CMA)
Install rail brackets on the Data Domain racks (for square or round
hole racks)
About this task
NOTE:
●Do not hold the bracket assembly in a vertical position as the parts may separate.
●If you are using a rack with threaded holes, skip this section and go to Install rail brackets using the adapter hardware
(for threaded hole racks) on page 17 section.
●The Data Domain system is 4 rack units (RU) tall so make sure the location in the rack fits the product. Attach the
bracket assembly to the lowest RU of the 4-RU opening.
●To comply with Data Domain rack mounting guidelines, the system controller should be installed in the pre-defined space
in the rack for system controllers. Refer to the Installation and Setup Guide for your system.
●For HA systems:
○Mount node 0 such that the bottom of the chassis aligns with the 13U mark in the rack.
○Mount node 1 such that the bottom of the chassis aligns with the 18U mark in the rack.
Steps
1. At each rack post, determine the vertical position in the rack where the brackets are to be installed. The top-most mounting
hole for a particular rack unit (RU) mounting position is typically identified by a mark or hole. The bracket will be installed in
the bottom hole of the 4 RU opening.
CAUTION: If the bracket is mounted in holes that are not vertically aligned from front to back, the bracket
may be damaged and mounting will not be secure.
2. As needed, select the bracket marked right or left. The rear of the bracket contains an adjustable piece.
3. From the rear of the system, hold the bracket against the inside of the rack posts. Align the rear guide pin and slide the
bracket towards the front. The guide pins can help to temporarily hold the rack mount bracket in place. Attach the bracket
to the rear of the rack using the furnished screws. There are five screw holes. The picture shows two screws attached to
the rear rack post.
Install the System in the Rack 15

Figure 8. Insert screw in the back
CAUTION: If the bracket is mounted in holes that are not vertically aligned from front to back, the bracket
may be damaged and mounting will not be secure.
4. Pull the adjustable sliding part of the bracket towards the front until it is close to, but not touching, the front of the rack.
Figure 9. Insert screw in the front
5. Attach the front of the brackets with two screws each in the two middle holes (innermost holes) as shown in the picture.
16 Install the System in the Rack

Figure 10. Attach bracket to front of rack
6. Verify that the bracket is level.
7. Repeat the steps to attach the remaining bracket to the other side of the rack.
8. After installing both brackets, make sure that they are level with one another.
Install rail brackets using the adapter hardware (for threaded hole
racks)
About this task
NOTE:
●If you are using a rack with square or round holes, go to Install rail brackets on the Data Domain racks (for square or
round hole racks) on page 15 section.
●Only use this procedure if your rack has tapped holes that are M5, M6, 10/32, or 12/24.
●The adapter hardware is shipped in the rack mount kit.
●You will need a long handled screwdriver with a shank diameter less than 7.0 mm and the wrench (included in the kit) to
tighten the nuts.
Steps
1. Locate the two adapters from the rail kit.
Install the System in the Rack 17

Figure 11. Adapters
1. Long adapter
2. Short adapter
2. Attach the long adapter to the front of each rail using M5 screws.
Figure 12. Attaching the front rail with the screw
3. Attach the small adapter to the rear of each rail using M5 screws.
4. At each rack post, determine the vertical position in the rack where the rails are to be installed. The top-most mounting hole
for a particular rack unit (RU) mounting position is typically identified by a mark or hole. Racks may also be screen-printed to
show the positions of the rack units.
NOTE:
●To comply with Data Domain rack mounting guidelines, the system controller should be installed in the pre-defined
space in the rack for system controllers. Refer to the Installation and Setup Guide for your system.
18 Install the System in the Rack

●Two people may be required to attach the rail/bracket assembly to the rack.
5. Install the screws supplied in the adapter kit to the rack. For example, the 10-32 threaded hole rack would require the
installation of the 10-32 screws. Install the screws in the appropriate locations until they are tight against the rack.
6. As needed, select the bracket marked right or left. Orientation assumes you are facing the front of the rack.
7. Slide the adjustable part of the bracket partly open.
8. Attach the first rail to the rack as follows:
a. Hold the rail against the inside of the rack with the rear bracket flush with the rear of the rack. Use the screws threaded
into the rack to hold the rear of the rail kit in place.
b. Pull the front of the rail until it is flush with the inside of the rack front.
c. Attach the rails to the rack by installing the appropriate nuts onto the screws threaded into the rack. Use the supplied
wrench to tighten the nuts. Do this for the front and rear of the rail kit.
d. Attach the rear of the rail/bracket assembly to the rear of the rack. Secure each screw.
Figure 13. Attach front rail adapter
9. Repeat the steps for the second rail.
10. After installing both rails, make sure that they are level with one another.
11. For HA systems, repeat this procedure for the second node.
Install the DD9800 system into a rack
About this task
CAUTION: Data Domain systems are heavy. Always use two people or a mechanical lift to move a system. The
chassis displays warning signs.
Install the System in the Rack 19

Figure 14. Warning about lifting the system
CAUTION:
●Do not apply AC power to the DD9800 system controller until all expansion shelves and cables are installed.
●Make sure the PSNT label, attached to the left rear of the chassis is not damaged or snagged during the
installation of the system into the rack.
Steps
1. Identify the designated location for the system controller in the rack.
●The designated location for a single node, or the primary node of an HA pair with ES30 shelves is U13-16 in rack 1.
●The designated location for the standby node of an HA pair with ES30 shelves is U18-21 in rack 1 (single rack) or U13-16
in rack 2 (multiple racks).
●The designated location for a single node with DS60 shelves is U23-26 in rack 1.
●The designated location for the primary node of an HA pair with DS60 shelves is U22-25 in rack 1.
●The designated location for the standby node of an HA pair with DS60 shelves is U27-30 in rack 1.
NOTE: The designated slots in the rack are the recommended location for the DD9800 system to support the cabling
described in this document. Other locations may require different cable lengths for some configurations.
2. From the front of the rack, lift the DD9800 system using the handles supplied for lifting to install the system in the rack in
the correct location.
3. At each side, align the bottom of the chassis with the lip of each installed rack bracket.
4. Carefully slide the chassis into the rack and remove the back handles while supporting the chassis weight. Continue to slide
the rest of the chassis and remove the front handles. Finally, push the chassis all the way into the back of the rack.
5. The rear of the chassis should engage with the tabs located in the rear of the rack mount kit.
6. At the front, attach the system to each installed bracket using the screws on the front of the system. The screws are shown
in red circles in the photo.
NOTE: On each side of the chassis, a bezel bracket sits between the upper and lower screws that secure the chassis
to the rack. The bezel brackets are marked with left and right to denote which side of the chassis to install them on.
However, the brackets for each side are not physically different. Inverting the bracket allows it to be used on the other
side of the chassis.
Figure 15. System on a rack
20 Install the System in the Rack