DELLA 1500W STOVE HEATER User manual

1500W STOVE HEATER
INSTRUCTION MANUAL
Item No: 050-HA-50095
**WARNING: READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE.
www.dellaproductsusa.com 909. 344. 2588
Electric Fireplace Stove with Heater
OWNER’S MANUAL
Item # 050-HA-50095
Model No. FP203R -T3
PLEASE SAVE THESE INSTRUCTIONS
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.


2
TABLE OF CONTENT
Thank you for choosing a DELLA Infrared Zone Heating System. This owner’s manual will
provide you with valuable information necessary for the proper care and maintenance
of your new product. Please take a few moments to thoroughly read the instructions and
familiarize yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS
SPECIFICATIONS
OVERHEAT SAFETY FEATURE
IN THE BOX
PREPARATION
ASSEMBLY INSTRUCTIONS
PRODUCT DIAGRAM
AUTOMATIC CUT-OFF
OPERATING YOUR HEATER
MAINTENANCE
WARRANTY
PLEASE LIKE, COMMENT AND SUBSCRIBE
03
04
04
04
04
05
06
07
07
08
09

3
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to reduce the
risk of re, electric shock, and injury to persons, including the following:
01. Read ALL instructions before using this unit.
02. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
03. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot
surfaces. If provided, use handles when moving this heater.
04. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and cur
tains at least 3 ft from the front of the heater and keep them away from the sides, top,
and rear. DO NOT place towels or other objects on the heater.
05. Extreme caution is necessary when any heater is used by or near children or the disabled,
or when the heater is left operating and unattended.
06. DO NOT operate any heater with a damaged cord or after the heater malfunctions, has
been dropped or damaged in any manner. Return heater to authorized service facility for
examination, electrical or mechanical adjustment, or repair.
07. This heater is not intended for use in bathrooms, laundry areas and similar indoor lo
cations. NEVER locate heater where it may fall into a bathtub or other water container. To
protect against electrical hazards, DO NOT immerse in water or other liquids.
08. DO NOT touch the control panel or plug with a wet hand.
09. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar
coverings. Arrange cord away from trac area and where it will not be tripped over.
10. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock or re, or damage the heater.
11. To prevent a possible re, DO NOT block the air intakes or exhaust in any manner. DO
NOT use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline,
paint, explosive and/or ammable liquids are used or stored. Keep unit away from heated
surfaces and open ames.
13. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension
cord or relocatable power tap (outlet/power strip).
14. To avoid re or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
15. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull rmly on
the plug, DO NOT unplug by pulling on the cord.
16. Always unplug the unit before moving or cleaning, or whenever the heater is not in use.

4
IMPORTANT INSTRUCTIONS
17. Use only for intended household use as described in this manual. Any other use not
recommended by the manufacturer may cause re, electric shock, or injury to persons. The
use of attachments not recommended or sold by unauthorized dealers may cause hazards.
18. Always use on a dry, level surface. Use on oor only.
19. DO NOT use outdoors.
20. WARNING: To reduce the risk of re or electric shock, DO NOT use this unit with any
solid-state speed control device.
21. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing
so will void your warranty. The inside of the unit contains no user serviceable parts. Qualied
personnel should perform all servicing only.
22. Connect to properly grounded outlets only.
23. Save these instructions.
SPECIFICATIONS
OVERHEAT SAFETY FEATURE
This heater is equipped with a overheat safety feature. When the heaters internal components
reach a certain temperature that could cause overheat and possible re, the heater will automat-
ically shut o.
IN THE BOX
*ELECTRIC STOVE *LEG (4pcs) *SCREW *INSTRUCTION BOOKLET
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with pack-
age contents list and hardware contents above. If any part is missing or damaged, do not attempt
to assemble the product. Contact customer service for replacement parts.
*Tools Required for Assembly (not included): Phillips screwdriver
Voltage Rating 120 V (60Hz)
Power Consumption 1500W
Unit Size 22.12 in.(W) x 13.67 in. D) x 25.54 in.(H)
Unit Weight 10.7 lbs


5
ASSEMBLY INSTRUCTIONS
Lay stove upside down on a padded surface with the underside accessible. Attach leg to stove
inserting the tab on the top of the leg into the corresponding slot on the bottom of the stove. Insert
screws into predrilled holes and tighten securely. Repeat with remaining three legs.
WARNING: IT IS NORMAL FOR THE POWER CORD TO FEEL WARM TO THE TOUCH; HOWEVER, A
LOOSE FIT BETWEEN THE OUTLET AND THE PLUG MAY CAUSE OVERHEATING OF THE PLUG. IF THIS
OCCURS, TRY INSERTING THE PLUG INTO A DIFFERENT OUTLET. CONTACT A QUALIFIED ELECTRI-
CIAN TO INSPECT THE ORIGINAL OUTLET FOR DAMAGE.
4
package contents list and hardware contents above. If any part is missing or damaged, do not
attempt to assemble the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Phillips screwdriver
ASSEMBLY INSTRUCTIONS
Lay stove upside down on a padded surface with the underside accessible. Attach leg to
stove by inserting the tab on the top of the leg into the corresponding slot on the bottom
of the stove. Insert three screws into predrilled holes and tighten securely. Repeat with
remaining three legs

6
PRODUCT DIAGRAM
6
Carbon bed
Display window
Power switch
Handle
Air outlet
Remote control

7
PRODUCT DIAGRAM
01. Power indication light: After electrifying show red, press the
power button to display the red light and ame open.
02. Power button: Powers the display on and o.
03. Flame light
04. Flame light button: Adjust the brightness of the ame
05. Timer light
06. Timer button: User setting timing boot or shutdown
07. Up button: For setting temperature or time upward
08. Down button:For setting temperature or time downward
09. Heater button: Set up the heater mode and
10. lights: Low range mode indicator lights up for low-grade heat
11. lights: High range mode indicator lights up for high-grade heat
Indicate set room temperature or time value according to the timer or High and low heating mode
display. After 5 seconds, the display window automatic blanking, press any key to the window auto-
matically display except for the power button.
8
1Power indication light: After electrifying show red, press the power button to display
the red light and flame open.
2Power button: Powers the display on and off.
3Flame light
4Flame light button: Adjust the brightness of the flame
5 Timer light
6Timer button: User setting timing boot or shutdown
7Up button: For setting temperature or time upward
8Down buttonFor setting temperature or time downward
9Heater button: Set up the heater mode and turn off the heat.
10Low range mode lights: Low range mode indicator lights up for low-grade heat.
11High range mode lights: High range mode indicator lights up for high-grade heat.
Digital display:
Indicate set room temperature or time value according to the timer or High and
low heating mode display. After 5 seconds, the display

8
REMOTE CONTROL
PREPARATION
Place the heater on a rm, level surface and plug into a grounded 120V 60Hz power outlet. And
turn on the power switch in the rear of the unit. Only operate heater in upright position with caster
wheels attached.
Insert 2 AAA batteries into the remote control before using (Batteries Not Included)
9
window automatic blanking, press any key to the window
automatically display except for the power button
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power
outlet. And turn on the power switch in the rear of the unit. Only operate heater in
upright position with caster wheels attached.
Power button: Powers the display on and off.
Flame light button: Adjust the brightness of the flame
Heater button: Set up the heater mode and turn off
Timer button: User setting timing boot or shutdown
Down buttonFor setting temperature or time downward
Up button: For setting temperature or time upward
Remote Control

9
OPERATING YOUR HEATER
Place the heater on a rm, level surface and plug into a grounded 120V 60Hz power outlet. and
turn on the power switch in the rear of the unit. Only operate heater in upright position with caster
wheels attached.
Insert 2 AAA batteries into the remote control before using (Batteries Not Included)
01. START AND SELECT WORKING MODE
10
Insert 2 AAA batteries into the remote control before using (Batteries Not Included)
OPERATING YOUR HEATER
Once the Electric fireplace has been properly assembled and connected to a
grounded electrical outlet, it is ready to operate:
1Start and select working mode
Or POWER
Turn the heater on by pressing the Power button on the
control panel or by pressing the Power button on the
supplied remote control.
Once power is off, heating element will stop working at
first. Fan will prolong working for 1 min to emit plenty of
heat inside. This mark will indicate running during the 3
min.
Or
Select a heat setting.
Press the HEATER button to toggle between the two heat
settings.
Power for heat-up mode is 1500W; heat-down is
750W,and turn off the heat.
2Setting room temperature
Or
Adjust the thermostat by pressing the arrows on the control
panel or remote control.
Set temperature indication varies from 59to 86. Once
you have chosen the desired temperature, the heater will
remain on until the room temperature increases to the
temperature on the digital display. The heater will cycle on
and off to maintain the desired room temperature.
3. Setting flame
02. SETTING ROOM TEMPERATURE
Turn the heater on by pressing the Power button on the control
panel or by pressing the Power button on the supplied remote
control.
Once power is o, heating element will stop working at rst.
Fan will prolong working for 1 min to emit plenty of heat inside.
This mark will indicate running during the 3 min.
Select a heat setting.
Press the HEATER button to toggle between the two heat
settings.
Power for heat-up mode is 1500W; heat-down is 750W,and turn
o the heat.
Adjust the thermostat by pressing the arrows on the control
panel or remote control.
Set temperature indication varies from 59°F to 86°F. Once you
have chosen the desired temperature, the heater will remain
on until the room temperature increases to the temperature
on the digital display. The heater will cycle on and o to main-
tain the desired room temperature.

10
OPERATING YOUR HEATER
11
Or
Adjust the brightness of the flame and turn off
4. Setting timer-power- off
Caution! ONLY under power-on mode can you set timer-power-off function.
Or
When starting the unit, press the timer button on the
control panel.
Adjust the time by pressing the arrows on the control panel
or remote control.
Digital display turns set temperature to time value for the
timer. Press the timer button more than once, the value will
vary from 0 to 12hr (1 hr interval) in circulation.
The light is on when timer –power-off is set.
5Setting timer-power-on
Caution! ONLY under power-off mode can you set timer-power-on function.
Under power-off, press the timer button on the control
panel.
Adjust the time by pressing the arrows on the control panel
or remote control.
Digital display indicates time value for the timer. Press the
timer button more than once, the value will vary from 0 to
12hr (1 hr interval) in circulation.
The light is on when timer –power-on is set.
6Setting electro lock
Function of electro lock can avoid misoperation from children. Locking can be set in both
power-on and power-off modes.
And
Press Temp Up and Temp Down buttons once for 3
seconds. Locking is fulfilled when a buzzer rings. When
Adjust the brightness of the ame and turn o
When starting the unit, press the timer button on the
control panel.
Adjust the time by pressing the arrows on the control
panel or remote control.
Digital display turns set temperature to time value for the
timer. Press the timer button more than once, the value
will vary from 0 to 12hr (1 hr interval) in circulation.
The light is on when timer –power-o is set.
Under power-o, press the timer button on the control
panel.
Adjust the time by pressing the arrows on the control
panel or remote control.
Digital display indicates time value for the timer. Press the
timer button more than once, the value will vary from 0 to
12hr (1 hr interval) in circulation.
The light is on when timer –power-on is set.
04. SETTING TIMER-POWER- OFF
Caution! ONLY under power-on mode can you set timer-power-off function.
05. SETTING TIMER-POWER-ON
Caution! ONLY under power-off mode can you set timer-power-on function.
06. SETTING ELECTRO LOCK
Function of electro lock can avoid misoperation from children. Locking can be set in both power-on
and power-off modes.
Press Temp Up and Temp Down buttons once for 3
seconds. Locking is fullled when a buzzer rings. When

11
12
locked, control panel and remote control failed to function.
When release is needed, please re-press Temp Up and
Temp Down buttons once for 3 seconds. Release is fulfilled
when a buzzer rings. Lock indication disappears. Control
panel and remote control return to function.
MAINTENANCE
1. Glass Information
* Under no circumstances should this product be operated with missing or broken glass.
* Do not strike or slam the glass.
* Do not use abrasive cleaners to clean the glass.
* Replacement glass is available from the manufacturer and replacement should be
carried out by a qualified service person.
2. Cleaning
*To clean the unit, first turn off controls on unit and unplug unit from power source.
*To clean the glass door: remove dust with clean dry cloth or to remove finger prints and
other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray
liquids on glass door surfaces.
*Metal and metal painted parts should be cleaned with clean damp cloth only. Do not
use abrasive cleaners or spray liquids on this surface.
3. If you do not use the heater for a long time, please take out the remote batteries (to
prevent corrosion) as shown below. Store the remote in a safe place.
TROUBLE SHOOTING
If the heater will not operate, please check the following before seeking repair of service:
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the outlet is working.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-
up, use the original packaging to repack the unit.
lid
Battery
When release is needed, please re-press Temp Up and
Temp Down buttons once for 3 seconds. Release is fullled
when a buzzer rings. Lock indication disappears. Control
panel and remote control return to function.
locked, control panel and remote control failed to function.
MAINTENANCE
1. Glass Information
* Under no circumstances should this product be operated with missing or broken glass.
* Do not strike or slam the glass.
* Do not use abrasive cleaners to clean the glass.
* Replacement glass is available from the manufacturer and replacement should be
carried out by a qualied service person.
2. Cleaning
* To clean the unit, rst turn o controls on unit and unplug unit from power source.
* To clean the glass door: remove dust with clean dry cloth or to remove nger prints and
other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray
liquids on glass door surfaces.
* Metal and metal painted parts should be cleaned with clean damp cloth only. Do not
use abrasive cleaners or spray liquids on this surface.
3. If you do not use the heater for a long time, please take out the remote batteries (to
prevent corrosion) as shown below. Store the remote in a safe place.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the
original packaging to repack the unit.
BASIC TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair advice:
01. Check if the power cord is plugged into an electrical outlet, if not, plug in.
02. Check if electricity to the main power switch (in the back) is working.
03. Check to see if the battery on the remote is placed correctly, undamaged.
NOTE: For the heater to function properly, the desired temperature on the heater must be set a few
degrees higher than the temperature in the room. If the seems to not be heating, increase the de-
sired temperature on the heater to engage the heat elements.

OUR BRAND
12

13
LIMITED TERM WARRANTY
ONE (1) YEAR FROM DATE OF PURCHASE
WARRANTY TERMS ADDITIONAL CONDITIONS
ADDITIONAL CONDITIONS
DELLA warrants that its merchandise are free from
manufacturing defects (workmanship and/or mate-
rial) and will either give credit or replace defective
parts for a period of up to one (1) year from the
date of purchase in accordance with the conditions
set forth below. If a manufacturing defect is found,
DELLA should be notied promptly of the defect
and supplied a copy of the invoice and delivery
ticket. Inspection by a DELLA employee or repre-
sentative may be necessary to verify that a man-
ufacturing defect exists, or you may be required
to submit samples to DELLA along with a digital
image of the defects. If replacement is required in
accordance with this warranty and the defective
material or merchandise has been discontinued or
unavailable, DELLA reserves the right to select and
supply similar merchandise or offer full credit for
the merchandise; otherwise the same material or
merchandise will be supplied for replacement pur-
poses. This warranty is made solely to the retailer
and is not transferable under any circumstances.
It is the retailer’s responsibility to contact DELLA
with a claim. We will not handle claims from con-
sumers directly; all requests must go through the
retailer who sold the merchandise to the consum-
er. We advise all retailers to retain invoices for a
minimum of one (1) year for warranty purposes.
This warranty supersedes and replaces all implied
warranties of merchantability and use for particular
purpose. No representative, employee, or agent of
DELLA or any other person is authorized to assume
for DELLA any additional liability or responsibility in
connection with DELLAs merchandise except as
described above. Implied warranties or merchant-
ability and tness of the merchandise are limited to
a period of one (1) year from the date of purchase.
In no event shall DELLA be liable for indirect, con-
sequential or incidental damages of any kind.
The following examples are not
manufacturer’s defects:
• Colors may vary slightly from the photo because
of photography and printing tolerances.
• Sizes are stated in U.S. standard measurements
while the actual sizes are manufactured using
the metric system. Therefore the sizes may
vary slightly.
• There are no exchanges or refunds on any
pillows or toppers sold.
• No returns for buyer’s remorse.
* No returns - other than stated above -
will be accepted
Warranty is void for any of the following conditions:
1 Improper maintenance or improper use resulting
in damage.
2 Any product modications by dealer, consumer,
or other parties not authorized by DELLA will
void this warranty.
3 Floor samples sold or products designated “AS
IS” at the time of purchase are not covered by
the warranty.
4 Warranty does not cover minor variations or
differences be tween oor samples or printed
illustrations and your furniture.
5 Cost of packaging and shipping to and from
DELLA is not covered by the warranty unless
expressly arranged by DELLA.
6 This warranty covers only articles of appliances
intended for residential use only, does not cover
any industrial, commercial, institutional, or
rental use.
7 Dissatisfaction due to buyer’s remorse.
8 Normal wear and tear.
9 Damages incurred during transportation.
10 Damages incurred during assembling
or maintenance.
11 Damages incurred by accidents or abuse.
Additional conditions for warranty on upholstery
are listed on the attached addendum.

**WARNING: READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE.
www.dellaproductsusa.com 909. 344. 2588