DELLA 050-HA-50070 User manual

**WARNING: READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE.
www.dellaproductsusa.com 909. 344. 2588
TOWER HEATER WITH
COOLING FAN
INSTRUCTION MANUAL
Item No: 050-HA-50070


2

3
TABLE OF CONTENT
Thank you for choosing a DELLA Infrared Zone Heating System. This owner’s manual will
provide you with valuable information necessary for the proper care and maintenance
of your new product. Please take a few moments to thoroughly read the instructions and
familiarize yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS
SPECIFICATIONS
SAFETY FEATURES
PRODUCT DIAGRAM
CONTROL PANEL
REMOTE CONTROL
PREPARATION
OPERATING INSTRUCTIONS
MAINTENANCE
STORAGE
BASIC TROUBLESHOOTING
WARRANTY
PLEASE LIKE, COMMENT AND SUBSCRIBE
04
05
05
06
06
07
08
08
09
11
12
13

4
IMPORTANT INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUCTIONS, SAFETY WARNINGS, BEFORE
USING THE HEATER
WARNING!
! POTENTIAL FOR ELECTRICAL HAZARD IF NOT ADHERED TO!
When using electrical appliances, basic precautions should always be followed to reduce the
risk of re, electric shock, and injury to persons, including the following:
01. CAUTION:RiskofElectricShock.DONOTopenortrytorepairtheheater yourself.
02. Thisheatermaygethotwheninuse.Toavoidburns,DONOTletbareskin touch hot surfaces. If
provided, use handles when moving this heater.
03. Keepcombustiblematerials,suchasfurniture,pillows,bedding,paper, clothes, and curtains at
least 3 ft from the front of the heater and keep them away from the sides, top, and rear.
DO NOT place towels or other objects on the heater.
04. Extremecautionisnecessarywhenanyheaterisusedbyornearchildrenor the disabled, or
when the heater is left operating and unattended.
05. DONOToperateanyheaterwithadamagedcordoraftertheheater malfunctions, has been
dropped or damaged in any manner. Return heater to authorized service facility for
examination, electrical or mechanical adjustment, or repair.
06. Thisheaterisnotintendedforuseinbathrooms,laundryareasandsimilar indoor locations.
NEVER locate heater where it may fall into a bathtub or other water container. To protect
against electrical hazards, DO NOT immerse in water or other liquids.
07. DONOTtouchthecontrolpanelorplugwithawethand.
08. DONOTruncordundercarpeting.DONOTcovercordwiththrowrugs, runners, or similar
coverings. Arrange cord away from trac area and where it will not be tripped over.
09. DONOTinsertorallowforeignobjectstoenteranyventilationorexhaust opening as this may
cause an electric shock or re, or damage the heater.
10. To prevent a possible re, DO NOT block the air intakes or exhaust in any manner. DO NOT
use on soft surfaces, like a bed, where openings may become blocked.
11 .A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline,
paint, explosive and/or ammable liquids are used or stored. Keep unit away from heated
surfaces and open ames.
12. Always plug heaters directly into a wall outlet receptacle. Never use with an extension cord
or relocatable power tap (outlet/power strip).
13. To avoid re or shock hazard, plug the unit directly into a 120 V AC electrical outlet.

5
IMPORTANT INSTRUCTIONS
14. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull rmly on the
plug, DO NOT unplug by pulling on the cord.
15. Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
16. Use only for intended household use as described in this manual. Any other use not rec
ommended by the manufacturer may cause re, electric shock, or injury to persons. The use
of attachments not recommended or sold by unauthorized dealers may cause hazards.
17. Always use on a dry, level surface. Use on oor only.
18. DO NOT use outdoors.
19. WARNING: To reduce the risk of re or electric shock, DO NOT use this unit with any sol
id-state speed control device.
20. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing
so will void your warranty. The inside of the unit contains no user serviceable parts. Qualied
personnel should perform all servicing only.
21. Connect to properly grounded outlets only.
SPECIFICATIONS
SAFETY FEATURES
TIP-OVER SAFETY FEATURE
This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal
switch will automatically shut the heater o. Once the heater is restored an upright position, the
heater will reset. To continue operation, turn on the heater using the supplied remote control or
the control panel on the heater.
OVERHEAT SAFETY FEATURE
This heater is equipped with a overheat safety feature. When the heaters internal components
reach a certain temperature that could cause overheat and possible re, the heater will automat-
ically shut o.
Voltage Rating 120 V (60Hz)
Power Consumption 1500W
Unit Size 9.5 in. (W) x11.9in. (D) x 21.3in. (H)
Unit Weight 22.2 lbs

6
WARNING: It is normal for the power cord to feel warm to the touch; however, a loose t between
the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a
dierent outlet. Contact a qualied electrician to inspect the original outlet for damage.
IN THE BOX
·INFRARED ZONE HEATING SYSTEM
·REMOTE CONTROL(2 AAA batteries not Included)
·INSTRUCTION BOOKLET
WARNING: This heater has a voltage rating of 120 volts. The
cord has a plug as shown in A. An adapter as shown in C is avail-
able for connecting three-blade grounding- type plugs to two-
slot receptacles. The grounding lug extending from the adapter
must be connected to a permanent ground such as a properly
grounded outlet box. The adapter should not be used if a three-
slot grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDED PLUG.
SAFETY FEATURES
PRODUCT DIAGRAM

7
CONTROL PANEL
01. Digital display:Indicates set desired room temperature or time according to the timer set.
02. High Mode indicator light: Will be lit when High Heat mode is engaged
03. Low Mode indicator light: Will be lit when Low Heat mode is engaged
04. Power indicator light: Indicates that the heater is receiving power from outlet. Will ash
when powered “ON’
05. Energy-saving mode (ECO) indicator: Will be lit when ECO mode is engaged
06. ON/OFF switch button: For power-on or o.
07. Mode button: To select between High, Low, and Eco modes
08. Temperature Up button: To increase desired temperature
09. Temperature Down button: To decrease desired temperature
10. °C/°F Button: Alternates between Fahrenheit and Celsius
11. Timer button: Used to engage timer mode and to set hour value for the timer
12. Fahrenheit indicator light: Will be lit when temperature displayed is in Fahrenheit
13. Timer indicator light: Will be lit when the Timer is engaged and active
14. Remote control signal sensor
15. Celsius indicator light: Will be lit when temperature displayed is in Celsius

OUR BRAND
8
REMOTE CONTROL
PREPARATION
Place the heater on a rm, level surface and plug into a grounded 120V 60Hz power outlet.
Heater to be operated only in upright position
Turn on the main power switch in the rear of the unit.Press the On/O button on the
display to power up the heater’s display.
You may use the ON/OFF button on the remote as well, but you will need to insert 2 AAA
batteries into the remote control battery compartment before using
(Batteries Sold Separately)
Temp up button: To increase desired temperature
ON/OFF button: Powers the display on and o
Temp down button: to make set temperature decline
Mode button: Used for mode selection
°C/°Fbutton: Button for alternating between Fahrenheit and Celsius
Timer button: Used to engage timer mode and to set hour value for the timer

9
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the supplied
remote control.
OPERATING INSTRUCTIONS
01. Start and select working mode
Turn the heater o by pressing the ON/OFF button on the
control panel or by pressing the Power button on the supplied
remote control.
Note: Powering o the heater will stop the heating process
only. The fan will continue to blow for approximately 1 more
minutes to allow for the interior components to cool. The fan
will then turn o automatically.
Select a heat Mode.
Press the MODE button to toggle between the three
heat settings.
High Mode uses 1500W; Low Mode uses 1000W. ECO mode
is an Economic Energy Saving Function. When ECO mode is
chosen, the heater will set the temperature automatically to
68°F (20°C) under this mode
High Mode uses 1500W; Low Mode uses 1000W. ECO mode is an
Economic Energy Saving Function. When ECO mode is chosen, the
heater will set the temperature automatically to 68°F (20°C) under
this mode
Desired temperature options vary from 59 to 86
, or from 15 to 30. Once you have chosen the desired tempera-
ture, the heater will remain on until the room temperature
increases to that temperature on the digital display. The heater
will cycle on and o to maintain that desired room temperature.
Press °C/°F button to change the display temperature between
Fahrenheit and Celsius.
02. Setting Desired Temperature

10
OPERATING INSTRUCTIONS
03. Setting the POWER-OFF TIMER Function
Note: The Power-O-Timer Function will allow for the heater to power OFF after a certain
set time, and can only be set while the heater’s display is in the “On” position.
04. Setting the POWER-ON TIMER Function
Note: The Power-ON-Timer Function will allow for the heater to power ON after a certain
set time, and can only be set while the heater’s display is in the “O” position.
Turn the heater to the “On” position. Press the Timer button
on the heater’s control panel or the remote.
Turn the heater to the “OFF” position. Press the Timer button
on the heater’s control panel or the remote.
The digital display shows the “hours” option for the timer.
Continue to press the timer button to change the number of
hours you would like the heater’s internal clock to count down
before powering itself on. The hour options for the timer are
from 0 to 12hrs. (In 1 hr increments).
The Timer indicator light will remain lit as long as the Timer is
set. The heater will power itself ON when the internal heater
clock counts down the hour increments you set.
The Fahrenheit indicator LED will light, when the temperature
is displayed in Fahrenheit.
The Celsius LED will light, when the temperature is displayed
in Celsius.
The digital display changes from the “temperature” to the
“hours “option for the timer. Continue to press the timer
button to change the number of hours you would like the
heater to run before powering itself o. The hour options for
the timer are from 0 to 12hrs. (In 1 hr increments).
The selected hour increments will ash for a few seconds, and
then revert back to the set desired temperature. The Timer
indicator light will remain lit as long as the Timer is set. The
heater will power OFF when the internal heater clock counts
down the hour increments you set.

11
OPERATING INSTRUCTIONS
05. Setting Electro Lock
The Electro Lock can help avoid the heater from being accidentally engaged by children.
The locking mechanism can be set in both the ON and OFF modes.
MAINTENANCE
01. Turn o the power switch in the rear of the unit.
02. Unplug the unit and let it cool completely
03. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth.
YOU MAY USE A MILD DETERGENT IF NECESSARY. AFTER CLEANING, DRY THE UNIT WITH A
SOFT CLOTH. CAUTION: DO NOT LET LIQUID ENTER THE HEATER.
04. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes
to clean the heater. This may cause damage or deterioration to the surface of
the heater.
05. DO NOT immerse the heater in water.
06. Wait until the unit is completely dry before use.
07. Air lter needs cleaning after used 3 months of use. Please take o the lter with the
Press Temp Up and Temp Down buttons at the same
time for 3 seconds. Locking is complete when you hear
a beep. When locked, the functions of the control panel
and remote will be locked for use.
When you need to unlock it, press Temp Up and Temp
Down buttons at the same time for 3 seconds. You will
hear a beep. The control panel and remote control will
become functional again.

12
08. If you do not use the heater for a long time, please take out the remote batteries (to
prevent corrosion) as shown below. Store the remote in a safe place.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up,
use the original packaging to repack the unit
BASIC TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair advice:
01. Check if the power cord is plugged into an electrical outlet, if not, plug in.
02. Check if power to the main power switch (in the back) is working.
03. Check to see if the battery on the remote is placed correctly, undamaged, and if the
insulating lm is pulled out.
NOTE: For the heater to function properly, the desired temperature on the heater must be
set a few degrees higher than the temperature in the room. If it seems to not be heating,
increase the desired temperature on the heater to engage the heat elements.
MAINTENANCE

13
LIMITED TERM WARRANTY
ONE (1) YEAR FROM DATE OF PURCHASE
WARRANTY TERMS ADDITIONAL CONDITIONS
ADDITIONAL CONDITIONS
DELLA warrants that its merchandise are free from
manufacturing defects (workmanship and/or mate-
rial) and will either give credit or replace defective
parts for a period of up to one (1) year from the
date of purchase in accordance with the conditions
set forth below. If a manufacturing defect is found,
DELLA should be notied promptly of the defect
and supplied a copy of the invoice and delivery
ticket. Inspection by a DELLA employee or repre-
sentative may be necessary to verify that a man-
ufacturing defect exists, or you may be required
to submit samples to DELLA along with a digital
image of the defects. If replacement is required in
accordance with this warranty and the defective
material or merchandise has been discontinued or
unavailable, DELLA reserves the right to select and
supply similar merchandise or offer full credit for
the merchandise; otherwise the same material or
merchandise will be supplied for replacement pur-
poses. This warranty is made solely to the retailer
and is not transferable under any circumstances.
It is the retailer’s responsibility to contact DELLA
with a claim. We will not handle claims from con-
sumers directly; all requests must go through the
retailer who sold the merchandise to the consum-
er. We advise all retailers to retain invoices for a
minimum of one (1) year for warranty purposes.
This warranty supersedes and replaces all implied
warranties of merchantability and use for particular
purpose. No representative, employee, or agent of
DELLA or any other person is authorized to assume
for DELLA any additional liability or responsibility in
connection with DELLAs merchandise except as
described above. Implied warranties or merchant-
ability and tness of the merchandise are limited to
a period of one (1) year from the date of purchase.
In no event shall DELLA be liable for indirect, con-
sequential or incidental damages of any kind.
The following examples are not
manufacturer’s defects:
• Colors may vary slightly from the photo because
of photography and printing tolerances.
• Sizes are stated in U.S. standard measurements
while the actual sizes are manufactured using
the metric system. Therefore the sizes may
vary slightly.
• There are no exchanges or refunds on any
pillows or toppers sold.
• No returns for buyer’s remorse.
* No returns - other than stated above -
will be accepted
Warranty is void for any of the following conditions:
1 Improper maintenance or improper use resulting
in damage.
2 Any product modications by dealer, consumer,
or other parties not authorized by DELLA will
void this warranty.
3 Floor samples sold or products designated “AS
IS” at the time of purchase are not covered by
the warranty.
4 Warranty does not cover minor variations or
differences be tween oor samples or printed
illustrations and your furniture.
5 Cost of packaging and shipping to and from
DELLA is not covered by the warranty unless
expressly arranged by DELLA.
6 This warranty covers only articles of appliances
intended for residential use only, does not cover
any industrial, commercial, institutional, or
rental use.
7 Dissatisfaction due to buyer’s remorse.
8 Normal wear and tear.
9 Damages incurred during transportation.
10 Damages incurred during assembling
or maintenance.
11 Damages incurred by accidents or abuse.
Additional conditions for warranty on upholstery
are listed on the attached addendum.

**WARNING: READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE.
www.dellaproductsusa.com 909. 344. 2588