Delta Children 27404 User manual

Customer Service: 1-(800)-377-3777
www.deltachildren.com
DCPIM12072016
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
INSTRUCTION MANUAL
ADULT ASSEMBLY REQUIRED
THIS PRODUCT CONTAINS SMALL PARTS
STYLES AND COLORS MAY VARY
Incline Sleeper
with Adjustable Feeding Position
For Newborns
27404
Required Tools: 4 "AA" Batteries (Not included), Screwdriver (Not included)

Customer Service Tel. [phone] www.deltachildren.com
2
Back Rest / Foot Rest Plastic Support
(Located inside seat pad)
WARNING: Failure to follow these warnings and the instructions could result in
serious injury or death.
FALL HAZARD: To prevent falls, STOP use of this product when the infant begins to
wiggle out of position or turn over in the product, or head touches the upper edge of
the product, or weighs more than 15 lb (6.8 kg) (approximately 3 months of age.)
ALWAYS use restraint system.
SUFFOCATION HAZARD
Infants have suffocated:
• On added pillows, blankets and extra padding.
• ONLY use the pad provided by the manufacturer.
• NEVER place extra padding under or beside infant.
• Remove any tools or excess parts including plastic packaging from the incline
sleeper vicinity after assembly.
• Always place child on back to sleep.
• Do not leave child unattended in the incline sleeper when it is in the “rocking”
mode. Always make sure the back brakes are in the “up” position.
• Always attach all provided fasteners tightly according to the instructions.
Check frequently. Do not use if there are any loose or missing parts or signs of
damage. Do not substitute parts. Contact the manufacturer for replacement parts.
• Toys are not to be “mouthed” by the baby and should be positioned clearly out
of reach of the baby’s face and mouth.
• Do not place medication, small toys, small items, cords, straps or similar items
that could become wound around the child’s neck in or near this product and do
not place product near a window, patio door, heater, or power outlet.
• When used as a feeder:
FALL HAZARD: To prevent death or serious injury, always keep child within
arm’s reach.
SUFFOCATION HAZARD: NEVER allow infant to sleep in product when in the
highest position. Highest position is for feeding only.
• Do not place items with a string around a child's neck such as hood strings or
pacifier cords. Do not suspend strings over the product or attach strings to toys.

Customer Service Tel. [phone] www.deltachildren.com
3
2 Base Tubes
Mobile Arm
Bear Canopy
(On Some Models)
Circle Plush
Canopy
(On Some Models)
Back Rest / Foot Rest Plastic Support
(Located inside seat pad)
Seat Pad
Mobile Arm
Insert Hole
Locking Foot
Left Side
Left Side
Back
Front
Front View
Locking Foot
Right Side
Right Side
Headrest
Back Support
Hub
Front Support
Hub
Mobile Arm
Insert Hole
Infant Support
Pad
Right Side Top
Support Tube
(Inner Side)
Left Side Top
Support Tube
(Outer Side)

Customer Service Tel. [phone] www.deltachildren.com
4
ASSEMBLY
2. Insert the front support hub into the right side
base tube, until it "clicks" into a fully locked
position. (Fig 2)
Back Support
Hub
Right Side Base
Tube
Right Side Base
Tube
Front Support
Hub
Back Support
Hub
Fully Locked
Position
Fig. 1
Fig. 2
1. Insert the end of the right side base tube into
the back support hub, until it "clicks" into a fully
locked position as shown. (Fig. 1)
ATTACHING HUBS TO BASE TUBES

Customer Service Tel. [phone] www.deltachildren.com
5
3. Insert left side base tube into the front and
back support hubs until they "click" into a fully
locked position as shown. (Fig 3).
Insert the left / right top support tubes into the top
of the front and back support hubs until they "click"
into a fully locked position. (Fig 4).
NOTE: The top support tubes are easier to
assemble if the base remains in the folded
position.
ASSEMBLY
Fig. 3
Front
Support
Hub
Fig. 4
Front Support
Hub
Locking
Foot Side
Back Support
Hub
Left Side Base
Tube
ATTACHING TOP SUPPORT TUBES
1.
Fully Locked
Position
Left Side Top
Support Tube
Right Side Top
Support Tube

Customer Service Tel. [phone] www.deltachildren.com
6
ASSEMBLY
Fully Opened
Position
Back
Support Tube
PULL
PULL
PULL
ATTACHING SEAT PAD
First, press the top button on the front support
hub and pull apart the top support tubes until
they "click" into a fully opened and locked
position (Fig. 5).
Second, press the bottom button on the front
support hub and pull apart base tubes until
they "click" into a fully opened and locked
position (Fig. 6).
NOTE: Make sure all tubes are in a fully
locked position, pull outward on the support
tubes.
Position the seat pad so that the headrest is
toward the back support hub. (Fig.7)
Place the seat pad over the top support tubes
making sure the inside fabric seat zipper edge
is draped on the inside of the support tube
and the outside printed fabric seat zipper edge
is draped on the outside of the support tube.
(Fig.7A)
Make sure seat pad insert holes are aligned
with the plastic mobile arm housing on support
tubes.
Fig. 6
Fig. 7 Fig. 7A
Seat Pad
Over Top Support Tubes
Fig. 5
First, press top button
to open top
support tubes
Second, press bottom
button to open
base tubes
1.
1. Mobile Arm
Insert Holes
Headrest
Top Support
Tube
Outside Printed
Fabric Seat
Outside Printed
Fabric Seat
Zipper Edge
Inside Fabric
Seat Zipper
Edge
Inside Fabric
Seat
OPENING INCLINE SLEEPER

Fully Fastened
Customer Service Tel. [phone] www.deltachildren.com
7
ASSEMBLY
Pull and align the inside fabric zipper edge to
the outside printed fabric zipper edge to allow
both edges to be fully zippered closed. (Fig. 8)
Repeat on other side.
Velcro close the front fabric seat flaps around
the left / right support tubes. (Fig. 9) Repeat
on back seat flaps. (Fig. 9A)
Make sure both front and back seat flaps are
securely velcro closed around the left / right
support tubes.
Second, press bottom
button to open
base tubes
2.
3.
Mobile Arm
Insert Hole
Zipper
Velcro
Zipper
Fig. 8
Fig. 9A
Back of Incline
Sleeper
Velcro Velcro
Headrest
Mobile Arm
Insert Hole
Velcro Headrest
Back Velcro
Piece
Front Velcro
Piece
Front of Incline
Sleeper
Velcro piece
flipped up
Fig. 9

Customer Service Tel. [phone] www.deltachildren.com
8
ASSEMBLY
ATTACHING INFANT SUPPORT TO SEAT PAD
REMOVING INFANT SUPPORT PAD FROM SEAT PAD
Infant support pad gets placed on top of seat pad.
Insert the waist belts attached to seat pad through
the slots on the infant support pad. (Fig.10) Make
sure the waist belts are not twisted.
Insert the restraint system through the bottom slot
on the infant support pad (Fig. 10A)
Remove the infant support pad from the seat
pad by removing the waist belts from the infant
support pad. (Fig. 11)
Remove the restraint system from the infant
support pad by pulling it through the bottom slot.
1.
1.
Infant Support
Pad
Infant Support
Pad
Slots
Seat Pad Seat Pad
Bottom Slot
Waist Belts
Fig. 10 Fig. 10A
Restraint
System
Infant Support
Pad
Slots
Seat Pad
Waist Belts
Fig. 11

Customer Service Tel. [phone] www.deltachildren.com
9
ASSEMBLY
To attach the bear canopy to the mobile arm, first
push the canopy up to the mobile arm tip. (Fig. 12)
To disassemble the mobile for storage, press the
tab on the mobile arm, and pull the mobile down.
(Fig. 12A)
Locate the battery compartment on the back of
the mobile arm base.
Hint: We recommend using alkaline batteries for
longer battery life.
• Loosen the screws in the battery compartment
door with a Philips screwdriver. (Fig. 13)
Insert four "AA" alkaline batteries into the battery
compartment.
• Replace the battery compartment door and
tighten the screws.
Note: Low battery power may cause product
movement to slow, sound to become faint or
product to turn off all together. If this should
happen, replace the batteries with four, new
alkaline "AA" batteries.
Fig. 12 Fig. 12A
Mobile Arm with Bear
Canopy attached
ATTACHING MOBILE ARM
BATTERY INSTALLATION
1.
2.
Battery Installation
Battery Compartment Cover
NOTE: We recommend using alkaline batteries for longer battery life.
Make sure batteries are correctly installed.
• Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities.
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid battery
leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
• When discarding batteries, be sure to dispose of them in the proper
manner, according to your state and local regulations.
1.5V x 4
"AA" (LR6)
1.5V x 4
"AA" (LR6)

Customer Service Tel. [phone] www.deltachildren.com
10
ASSEMBLY
Align and slide down mobile arm onto plastic
housing. It will "click" when it is fully clipped on.
(Fig. 13)
90 swivel arm (Fig. 14)
NOTE: When removing baby from incline
sleeper, rotate the mobile arm away from the
sleeper. (Fig. 14)
NOTE: Mobile arm can be attached on the left or
right sides of the incline sleeper.
3.
Fully Clipped
Mobile arm has
two placement
locations
Fig. 13
Fig. 14

Customer Service Tel. [phone] www.deltachildren.com
11
MOBILE AND VIBRATIONS UNIT OPERATION
OPERATION
OnOff
Rotate Mobile Toys
Twinkling Lights
Music
Vibration
Night Light
Mobile Functions On/Off
Vibrations
Switch
Music Volume
Switch
Mobile Functions On/Off Switch
• Push the Mobile Functions On/Off button at the base of the mobile
arm to turn on power. This is the main power switch to the mobile
arm and also turns on the power LED on the Night Light button.
The LED will stay on in the dark.
Rotate Mobile Toys Button
• Press to begin a 5 minute cycle of rotation.
• Press again to stop the mobile.
• Press to start a new 5-minute cycle. If this button is pressed while
mobile is operating, the rotation cycle will restart.
Twinkling Lights Button
• Press to start a 5 minute light show.
• Press again to stop the light show.
Music Button
• Press to start cycle of music.
• Press again to stop the music.
Vibration Button
• Press to start 5-minute cycle of vibration.
• Press again to stop vibration.
Night Light
• Press to turn on mobile light for 5 minutes.
• Press again to turn light off.
Vibration Switch
• Push toward + to increase vibration.
• Push toward – to decrease vibration.
Music Volume Switch
• Push toward + to increase volume.
• Push toward – to decrease volume.
MP3 Cord
• Plug audio cord into MP3 player.
• To adjust volume, follow instruction above or use MP3 function.

Customer Service Tel. [phone] www.deltachildren.com
12
SECURING CHILD
Crotch Belt
Waist Belt
Waist Belt
Restraint System
Place your child in the incline sleeper.
Position the crotch belt between your child’s
legs. Fasten both waist belts to the buckle on
each side of the crotch belt. Make sure you
hear a “click” on both sides. Check to be sure
the restraint system is securely attached by
pulling it away from your child. The restraint
system should remain attached. (Fig. 15)
Tighten each waist belt so that the restraint
system is snug against your child. Please refer
to the next section for instructions to tighten
the waist belts. (Fig. 16)
Fig. 15
Fig. 16
1.
2.
Infant
Support
Pad
Seat
Pad
Restraint
System

Customer Service Tel. [phone] www.deltachildren.com
13
TIGHTEN
LOOSEN
3.
4.
To tighten the waist belts:
• Feed the anchored end of a waist belt up
through the buckle to form a loop A. Pull
the free end of the waist belt B. (Fig. 17)
• Repeat this procedure to tighten the other
waist belt.
Please note: After adjusting the restraint system
to fit your child, make sure you pull on it to be
sure it is securely fastened.
To loosen the waist belts:
• Feed the free end of the waist belt up
through the buckle to form a loop A. Enlarge
the loop by pulling on the end of the loop
toward the buckle. Pull the anchored end of
the waist belt to shorten the free end of the
waist belt B. (Fig. 18)
• Repeat this procedure to loosen the other
waist belt.
Fig. 17
Fig. 18
SECURING CHILD

Customer Service Tel. [phone] www.deltachildren.com
14
NOTE: There are three height positions. The
lowest positions are the sleeping positions.
(Fig. 20) and (Fig. 20A)The highest position is
the feeding position (Fig. 21).
To adjust height positions, press the button
located under the back support hub. While
pressing the button, hold the left or right top
support tubes while adjusting height. (Fig. 19)
At desired height position, it will "click" when it is
locked. Release button once you hear the "click".
Sleeping Position can be on either the lowest or
middle height position. (Fig. 20) and (Fig. 20A)
Feeding Position is the highest position, and
must be in a non-rocking position. (Fig. 21)
Fig. 19
Fig. 20
Fig. 20A Fig. 21
Feeding Position -
Highest Position
Non-Rocking Position
Sleeping Position -
Lowest Position
Sleeping Position -
Middle Position
HEIGHT ADJUSTMENTS - SLEEPING TO FEEDING
1.
Back Support
Hub
Non-Rocking
brakes rotated
out
• When used as a feeder:
FALL HAZARD: To prevent death or serious injury, always keep child within
arm’s reach.
SUFFOCATION HAZARD: NEVER allow infant to sleep in product when in the
highest position. Highest position is for feeding only.
NOTE: Non-Rocking brakes have to be rotated
out when feeding.
NOTE: Never raise with child in seat.

There is a rocking and non-rocking position. Rotate
out the non-rocking brakes, located on the bottom
left / right side back base tubes, until they click into
a fully locked position. (Fig. 22)
To return to a rocking position, rotate rocking
brakes back into a closed position. (Fig. 23)
ROCKING AND NON-ROCKING POSITION
Fig. 22
Fig. 23
Customer Service Tel. [phone] www.deltachildren.com
15
ASSEMBLY
Non-rocking Position
Rocking Position
Non-Rocking Brakes
1.
2.

First, pull outward on inside mobile arm clip, then lift
the mobile arm off the top support tube. (Fig. 24)
Fig. 24
Pull
outward
Customer Service Tel. [phone] www.deltachildren.com
16
ASSEMBLY
REMOVING SOUND MODULE
Separate velcro flaps on both top and bottom of
the incline sleeper. Unzip the seat pad from both
sides. Pull the pad off. (Fig. 25)
Unzip
Unzip
Remove
Velcro
Flaps
Fig. 25
REMOVING SEAT PAD
1.
1.
Remove
Velcro
Flaps

Customer Service Tel. [phone] www.deltachildren.com
FOLDING INCLINE SLEEPER
WITH OR WITHOUT SEAT PAD
First, push the top button on the locking hub and
push together the top support tubes until they are
fully closed. (Fig. 26)
Second, press the bottom button on the locking
hub and push the base tubes together until they
are fully closed. (Fig. 27)
NOTE: Incline Sleeper can also be folded with
seat pad attached.
PUSH
Fig. 27
Fig. 28
Press top button
to close liner tubes
Press bottom button
to close base tubes
PUSH
PUSH Fully Closed
Position
Fig. 26 Fig. 27
1.
2.
17

CARE AND MAINTENANCE
Washing Instructions:
1. Remove infant support pad
2. Remove seat pad from top support tubes
3. Remove back rest / foot rest plastic supports, located under the seat pad.
Check Incline Sleeper for worn parts, torn material or stitching periodically. Replace or repair the
parts as needed. Use Delta replacement parts.
The seat pad and infant support pad are machine washable. Wash them separately in cold water
on the gentle cycle. Do not use bleach. Tumble dry separately on low heat and remove promptly.
The frame and mobile arm may be wiped clean using a mild cleaning solution and a damp cloth.
Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove
residue. Do not immerse the frame.
Customer Service Tel. [phone] www.deltachildren.com
18
Velcro Pockets
Seat Pad
Infant Support
Pad
Remove back rest / foot rest
plastic supports
Underneath Seat
Pad