Dennis VERTICUT T.T. User manual

VERTICUT T.T.
VERTICUTTER
INSTRUCTION MANUAL
DENNIS, Ashbourne Road, Kirk Langley, Derby, DE6 4NJ, United Kingdom
Telephone:- 01332 824777
Fax:- 01332 824 525
E-mail:- [email protected]
E-mail:- [email protected]
www.dennisuk.com SP20007_REV_0
04/12

THIS INFORMATION IS INTENDED FOR GUIDANCE PURPOSES ONLY. WE RECOMMEND THAT YOU DISCUSS YOUR SPECIFIC REQUIREMENT WITH OUR HEAD OFFICE, SALES MANAGERS OR YOUR LOCAL DENNIS DEALER.
NOTE
Product Application Matrix
Razor G660 Bray Application FT Razor Ultra Simplex G560 SuperSix G760 Premier Contractor Hand S500 Gang Verticut
Range 560 560 Range G680 Range G860 Range Tools Plus Mower T.T.
Bowling Green 99999999
Cricket Ground Maintenance: wicket 9999999
square 9999999
RXW¿HOG       999 Football Pitch 999  Golf Course Maintenance: Tees 99999999 Greens 9999999 Ornamental 999999
Croquet Green 999999999 Grass Tennis Court 99999999 Race Course Maintenance: Parade Ring 99999999 Ornamental 99999999 9 Rugby Pitch 999  Hockey Pitch 99 Sports Club Maintenance 999999999999 9 Schools, Colleges & University Grounds 999999999999 9 Cemetery Maintenance 9999 Contractors, Private Lawns & Commercial 9999999 9 Local Authority & Government Contracts 999999999999 9 Ornamental Lawn 99999999 9

3
Verticut T.T. SP20007_REV_0
&HUWL¿FDWHRI&RQIRUPLW\
Verticut T.T. powered by Honda GX Petrol Engine
0DQXIDFWXUHU Howardson Ltd, Howardson Works, Kirk Langley, Derby, DE6 4NJ. UK
2ZQHURI7HFKQLFDO'RFXPHQW Mr I.D. Howard, Howardson Ltd, Howardson Works Kirk Langley, Derby, DE6 4NJ, UK
I the under signed Declare that these machines:-
The reliability and quality of performance of the '(11,69(57,&8777 depends upon some simple care maintenance
carried out regularly. This manual has been prepared to allow the user to carry out all such work.
It is advisable to read the instructions carefully. Proper care and attention will enable the machine to give a continuous,
satisfactory, and reliable service. Failure to carry out regular lubrication and maintenance as outlined in this manual may
render any guarantee or warranty invalid.
,QWKHFDVHRIDQ\GLI¿FXOW\RULIIXUWKHULQIRUPDWLRQRUDGYLFHLVUHTXLUHGRXU6HUYLFH'HSDUWPHQWLVDOZD\VDW\RXUFDOO,Q
the interests of speed and accuracy of information please quote the serial numbers of the machine and engine when
making enquiries.
For the mower, this is to be found on a plate attached to the side frame. The engine number is stamped on either the
crank case or the gear casing facing towards the front of the machine. We suggest you write the numbers on the front
page of this book.
,QWURGXFWLRQ
Serial Numbers
0$&+,1(6(5,$/180%(5
MAKE A NOTE OF THE SERIAL NUMBERS OF YOUR MACHINE & ENGINE AND ALWAYS
QUOTE THEM IN ANY COMMUNICATION WITH PERSONNEL AT DENNIS.
NOTE
(1*,1(6(5,$/180%(5
Model Cutting Width Power (Honda) Measured Sound Power
Level Guaranteed Sound Power Level Serial Number
510 20” (510mm) GX160 95dB Lwa 98dB Lwa See Product ID range
7HVWHGDWHowardson Works test site September 2011
Complies with the applicable requirements of:-
- Machine Directive 2006/42/EC
- Noise Directive 2000/14/EC (Annex V)
0DQDJLQJ'LUHFWRU
,DQ+RZDUG

4
Verticut T.T. SP20007_REV_0
Contents
Page
Product Application Matrix.................................................................................................................................................... 2
Declaration of Conformity.....................................................................................................................................................3
Serial Numbers..................................................................................................................................................................... 3
Introduction........................................................................................................................................................................... 3
Technical Data...................................................................................................................................................................... 4
Machine Description............................................................................................................................................................. 5
Important Safety Instructions................................................................................................................................................ 6
Controls................................................................................................................................................................................ 7
Operating Instructions .....................................................................................................................................................8 - 9
General Adjustments.......................................................................................................................................................... 10
Routine Maintenance....................................................................................................................................................11 - 12
Storage............................................................................................................................................................................... 12
General Lubrication............................................................................................................................................................ 13
Parts Listings...............................................................................................................................................................14 - 27
7HFKQLFDO'DWD
Model 510
A - Width (mm) 706
B - Length with Grassbox (mm) 7566
C - Length without Grassbox (mm) 1203
D - Height (mm) 983
Weight (Kg) 120
Operating Width (mm) 510
Engine Honda GX160
Drive System “V” Belt
Final Drive Poly “V” high performance belts under
constant tension
Hand Arm Vibration (m/sec2)2.5
Measured Sound Power Level dB(A) LWA 95
Guaranteed Sound Power Level dB(A) LWA 98
ABC
'

5
Verticut T.T. SP20007_REV_0
0DFKLQH'HVFULSWLRQ
Manufactured with a 20” (51cm) width, this range of machines is powered by a 5.5hp air cooled, single cylinder, four
stroke petrol engine.
The rear roller and cutter are controlled independently via belt clutches operated from the console on the upper handle
EDU,7(0$SDUNLQJEUDNHLV¿WWHGIRUDGGHGVDIHW\ZKHQZRUNLQJRQVORSLQJJURXQG
In the design of the machine, special attention has been given to the importance of easy service and maintenance with
the construction based on a sectional assembly system. These are the Engine Unit, the Cutter, the Rear Roller Unit, and
the Front Roller Unit, each of which can be readily removed individually from the main Frame Chassis Unit.
The interchangeable cassette system allows a variety of cassettes to be used for varying applications.
1. Verticut Head 9. Height Adjustment
2. Belt Guard 10. On / Off Switch
3. Throttle Control Lever 11. Verticut Head Control Lever
4. Operating Console 12. Air Filter
5. Exhaust 13. Driving Control Lever
6. Fuel Tank 14. Deadmans Handle
7. Brake Lever 15. On / Off Switch
8. Grassbox
1
2
7
3
4
5
6
8
13
9
10 11
12
14

6
Verticut T.T. SP20007_REV_0
,PSRUWDQW6DIHW\,QVWUXFWLRQV
In order to operate the machine safely please follow these Health and Safety guidelines.
75$,1,1*
READ THE INSTRUCTIONS CONTAINED IN THIS MANUAL WITH CARE. IF YOU ARE IN
ANY DOUBT PLEASE ASK YOUR EMPLOYER OR CONTACT US DIRECT AT DENNIS.
&$87,21
 Be familiar with the controls and the proper use of the equipment.
 Never allow children or people unfamiliar with these instructions to use the machine. Local regulations or insurance
may restrict the age of the operator.
 Never operate while people, especially children, or pets are nearby.
 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their
property.
35(3$5$7,21
 While operating always wear substantial footwear and long trousers. Do not operate in barefoot or in open
sandals.
 Thoroughly inspect where the equipment is to be used and remove all stones, sticks, wire, bones and other foreign objects.
PETROL IS HIGHLY FLAMMABLE AND WILL DAMAGE GRASS IF SPILT.
:$51,1*
$ 6WRUHIXHOLQFRQWDLQHUVVSHFL¿FDOO\GHVLJQHGIRUWKLVSXUSRVH
B) Refuel out doors and do not refuel whilst smoking.
C) Add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the engine is running or
when the engine is hot.
D) If petrol is spilled do not attempt to start the engine but move the machine away from the area of spill and avoid
creating any sources of ignition until the vapours have dissipated.
 Replace damaged or faulty silencers.
 Before using the machine always inspect the safety devices including the cut off switch and the blades for excessive
wear or damage. Replace if necessary.
23(5$7,21
 'RQRWRSHUDWHWKHHQJLQHLQDFRQ¿QHGVSDFHZKHUHGDQJHURXV&$5%210212;,'( fumes can collect.
 2SHUDWHRQO\LQGD\OLJKWRUJRRGDUWL¿FLDOOLJKW
 Avoid operating the machine in wet grass where feasible.
 Always be sure of your footing on slopes.
 Walk. Never run.
 Walk across the face of slopes, never up and down.
 Exercise extreme care on slopes when changing direction.
 Do not operate excessively steep slopes.
 Use extreme caution when reversing or pulling the machine towards you.
 Stop the blades if the machine has to be tilted for transportation when crossing surfaces other than grass and when
transporting the machine to and from the area to be cut.
 Never operate the machine with defective guards or shields or without the safety devices, for example without the
 GHÀHFWRUSODWHRUJUDVVER[LQSODFH
 Do not change the engine governor settings or overspeed the engine.
 Disengage all drive clutches before starting.
 Start the engine carefully following the instructions with feet well away from the blades.
 Do not tilt the machine when starting the engine.
 Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
 Never pick up or carry the machine while the engine is running.

7
Verticut T.T. SP20007_REV_0
Controls
)257+(/2&$7,212)&21752/6$1'&20321(1765()³0$&+,1('(6&5,37,21´3$*(
212))6:,7&+,WHP
This switch stops the engine and can be used to do so at anytime during the operation of the machine. Ensure it is in the ³21´
position before attempting to start the engine.
'($'0$16&21752/,WHP
This is an operator presence control. The engine will tick over without need for this to be depressed when the cutter and drive
are disengaged. This must be depressed before the drive or cutter can be engaged. Failure to do so will cause the engine to
stop.
7+5277/(&21752/,WHP
This controls the RPM of the engine and the resultant speed of the machine. Pushing the lever forwards will increase the RPM,
pulling it back returns the engine to idle.
'5,9(&2172/,WHP
This controls the machine movement. Pulling the lever upwards will engage the belt clutch and cause the machine to drive.
Returning it to the original position will cause the machine to stop.
&877(5&21752/,WHP
This controls the Verticutter drive. Pushing the lever forwards will engage the belt clutch and cause the cutter to rotate. Return-
ing it to the original position will cause the cutter to stop.
IF THE “DEADMANS CONTROL LEVER” IS DEPRESSED WHILE THE PARKING BRAKE IS
ON THE ENGINE WILL STOP.
NOTE
IF THE “DEADMANS CONTROL LEVER” IS DEPRESSED WHILE THE PARKING BRAKE IS
ON THE ENGINE WILL STOP.
NOTE
3$5.,1*%5$.(&21752/,WHP
This controls the parking brake. It is only to be engaged when the machine is stationary, it is NOT to stop the machine. Push
lever forwards to engage and pull back to disengage.

8
Verticut T.T. SP20007_REV_0
2SHUDWLQJ,QVWUXFWLRQV
35(3$5$7,21)2586(
 Before commencing ensure the turf is free from stones or other obstructions which may damage the cutter unit.
 Set the height of cut to the required level (see page 10)
 Check the engine.
 Fill the fuel tank 3/4 full with unleaded petrol.
 Always check the oil levels of the machine prior to commencing. Full details are given in the (1*,1( Manual, which
accompanies this book. A daily check is recommended. (Recommended grade oil is SAE 10W-40).
 Disengage the cylinder drive. (see next page)
 Set the throttle control on the handle bars to the idle position.
BEFORE YOU OPERATE THIS MACHINE YOU MUST READ AND STUDY THIS MANUAL.
IF YOU ARE IN ANY DOUBT PLEASE ASK YOUR EMPLOYER OR CONTACT US DIRECT.
&$87,21
IMPORTANT INFORMATION PLEASE READ ALL THE DETAILS IN THIS SECTION AND
FAMILIARIZE YOURSELF AND ALL MACHINE OPERATORS WITH THE CONTENTS.
&$87,21
67$57,1*7+((1*,1(
Once the preparatory steps have been completed as outlined on page 7 the engine may be started. (See manufacturer
operating manual for full details).
1) Switch on the fuel tap.
2) Switch the handlebar cut off switch to ON, or depress deadmans handle (Item 1)
3) Set the throttle control to a half open position.
3) Shift the choke lever to the appropriate position. Honda engine set to the &/26( position). The choke is not required
if the engine is warm or the air temperature high.
4) Grasp the recoil start handle until resistance is felt, then pull it with force.
5) Do not allow the starter grip to snap back against the engine. Return it gently to prevent damage to the starter.
6) Once the engine is started gradually ‘open’ the choke lever (move the lever towards the 5811,1*, or OPEN
position). Warm-up running of 3-5 minutes is recommended.
67233,1*7+((1*,1(
1) Set the throttle control to the &/26(' position.
2) Switch the handlebar cut off to OFF or release deadmans handle.
3) Close the fuel tap.
72&200(1&('5,9,1*75$163257%(7:((16,7(612&877,1*
 Ensure the ³3DUNLQJ%UDNH´ is disengaged.
 Depress the ³'HDGPDQV+DQGOH´ (Item 15)
 Pull the ³'ULYH&RQWURO/HYHU´ (Item 14) upwards.
 Set the ³7KURWWOH&RQWURO/HYHU´ to increase / reduce speed.
726723'5,9,1*
 5HOHDVHWKH³'ULYH&RQWURO/HYHU´(Item 14) backwards.

9
Verticut T.T. SP20007_REV_0
2SHUDWLQJ,QVWUXFWLRQV
72&200(1&(&877,1*
 Depress the ³'HDGPDQV+DQGOH´ (Item 15)
 Push the ³&\OLQGHU&RQWURO/HYHU´ (Item 12) forwards.
 3XVKWKH³'ULYH&RQWURO/HYHU´(Item 14) forwards.
 Set the ³7KURWWOH&RQWURO/HYHU´ to increase / reduce speed.
726723&877,1*
 5HOHDVHWKH³'ULYH&RQWURO/HYHU´(Item 14)
 Pull the ³&\OLQGHU&RQWURO/HYHU´ (Item 16) backwards.
 Release the ³'HDGPDQV+DQGOH´ (Item 15)
RELEASING THE “DEADMANS CONTROL LEVER” WITH THE CUTTER ENGAGED WILL
CAUSE THE ENGINE TO STOP
NOTE
*(1(5$/
Used from ground +3mm to ground -3mm to control thatch, cutting lateral growths and standing up lying grasses ready for
cutting and lifting with the comb. Good for removing mosses. Start on the green at (say) +3mm.
NOT FOR CUTTING SOIL, ONLY THATCH.
NOTE
RESULT - Speed improvement on greens,reduced end of season maintenance. Promotes healthy plant growth, promotes
strong roots, and maximizes fertilizer penetration.

10
Verticut T.T. SP20007_REV_0
General Adjustments
6(77,1*)25+(,*+72)&87
Always stop the engine before adjusting the height
of cut. Failure to do this may result in serious injury.
The depth after cutting depends on the setting of
the front roller in relation to the main frame of the
machine.
7RVHW
 6LPSO\URWDWHWKHNQREPDUOHG‘A’ to raise and
lower the height of cut.
+$1'/(%$5$'-8670(17
The height of the Handle Bars can be adjusted to
suit various operators. Follow the below
instructions:-
1. Remove Bolt (Item 1) on both sides of the
machine.
2. Select the required position out of the 3
available.
3. Replace the Bolt on both sides of the machine.
GRASS BOX
If using the grass box, place the two locating tabs (projecting from the grass box support plates) into the slots on the
machine side plate. Lower the front of the box until the box support plates rest on the front cross bar of the machine.
Ensure both box support plates are properly located before proceeding.
Always disengage the cylinder drive before removing the grass box for emptying or access by reducing the engine revs
to tick over. Wait for the cutter to stop before removing.
$OZD\VNHHS¿QJHUVDZD\IURPWKHF\OLQGHUZKHQWKHHQJLQHLVUXQQLQJ6WRSWKHPDFKLQHEHIRUHPDNLQJDQ\
adjustments.
+ROGWKHJUDVVER[¿UPO\RQWKHOLSRIWKHDSHUWXUHDQGSODFHWKHRWKHUKDQGRQWKHIURQWHGJHRIWKHER[
A
,WHP

11
Verticut T.T. SP20007_REV_0
52//(5&/87&+
The Primary Rear roller drive belt is shown in Fig 1.
This is a special Kevlar V belt design for clutching
applications. The Rear roller clutch pulley moves
into tension the belt via a control cable. The tension
in the cable can be adjusted as shown in Fig 1
[13mm spanner].
Under tensioning this belt will lead to slip and
cause rapid wear. Over tension will put excessive
stain on the belt and bearings.
The Secondary Rear roller drive belt is shown in Fig 2 (item1). This is a hard wearing poly-V belt. Belt tension is the single
most important factor necessary for long,
satisfactory service life of any belt drive.
Under-tensioning leads to belt slip causing rapid wear; over tensioning means excessive strain on belt and bearings.
Between these two extreme conditions is a reasonable range of tension within which the belt will operate. Belt tension can
EHDVVHVVHGE\WKHµGHÀHFWLRQ¶PHWKRG
Routine Maintenance
CORRECTION CAN BE MADE BY ADJUSTMENT OF THE BELT TENSIONERS. REMOVE
THE DRIVING BELT COVER. THE BELT TENSIONERS ARE RETAINED IN A SLOTTED
HOLE ALLOWING ADJUSTMENT TO BE MADE ONCE THE HOLDING HEXAGON
HEADED BOLTS HAVE BEEN LOOSENED. WHEN ADJUSTED CORRECTLY THE
TENSIONERS SHOULD STILL ROTATE EASILY WITH FINGER PRESSURE. ENSURE THE
TENSIONER BOLTS ARE SECURE BEFORE REPLACING THE COVER.
NOTE
³%HOWVZLOOEHVXI¿FLHQWO\WHQVLRQHGLIWKHGHÀHFWLRQIRUFHDSSOLHGDWPLGVSDQWRSURGXFHDGHÀHFWLRQHTXDOWRPPSHU
meter of span distance falls between 5 and 9 Newtons per Rib” (TBA Belting).
,QSUDFWLFDOWHUPVWKLVUHODWHVWRDERXWPPRIGHÀHFWLRQXQGHUPRGHUDWH¿QJHUSUHVVXUHRQWKHQRQWHQVLRQHUVLGH
,I¿WWLQJQHZEHOWVLWLVDGYLVDEOHWRREVHUYHWKHGULYHIRUWKH¿UVWPLQXWHV,WPD\EHQHFHVVDU\WRPDNHDQ
adjustment to compensate for the normal drop in tension during the run-in period.
2,/)8(/7<3(48$17,7<63$5.3/8*7<3(
Engine Model Oil Type Quantity
(Ltr) Fuel Type Capacity (Ltr) Spark Plug Type Electrode Gap (mm)
Honda GX160 Petrol SAE 10W-40 0.6 Unleaded 2.5 BM6ES or BPR6ES 0.7 - 0.8
Area Maintenance First 4 Hours First Month / 20 Hours 3 Months / 50 Hours 6 Months / 100 Hours
Engine Oil Check Level 9
Engine Oil Change 99
Air Filter Check Condition /
Clean 99
Spark Plug Change 9
(1*,1(
7KHPDFKLQHVDUH¿WWHGZLWKD+RQGD*;SHWUROHQJLQH
)RUIXOOVSHFL¿FDWLRQVSOHDVHUHIHUWRWKHPDQXIDFWXUHUVLQVWUXFWLRQPDQXDOLQFOXGHG
,WHP
1
Fig
1

12
Verticut T.T. SP20007_REV_0
&</,1'(5&/87&+
7KH&\OLQGHUGULYHEHOWVDUHVKRZQLQ¿JLWHP
7KHUHDUHVSHFLDO.HYODU9EHOWV¿WWHGLQSDLUVDQG
designed for clutching applications. The cylinder
clutch pulley moves into tension the belt via a
control cable. The tension in the cable can be
DGMXVWHGDVVKRZQLQ¿J>PPVSDQQHU@
Under tensioning this belt will lead to slip and
cause rapid wear. Over tension will put excessive
stain on the belt and bearings.
&$%/($'-8670(17
Over time the cables that operate the clutch pulleys and the brake will need adjusting. This adjustment can be carried out
at either end of the cables [10mm spanner].
Routine Maintenance
NEITHER CLUTCHES OR BRAKE SHOULD OPERATE WITH THE CONTROLS IN THE
OFF POSITION.
NOTE
,WHP
1
Cylinder
&OXWFK
Fig
2
ENSURE THE LOCK NUTS ARE TIGHT AND SECURE AND CHECK OPERATION IS
SATISFACTORY BEFORE REPLACING THE CLUTCH COVER AND SCREWS.
NOTE
Storage
The machine should always be kept in a clean dry place, free from condensation. After use ensure that the machine is
thoroughly clean, dry and free from grass and mud.
Under no circumstances must the machine be steam cleaned as this may remove grease from the pre packed bearings.
Because of the nature of lead free petrol we recomend that if the machine is being left unused for more than 2 weeks the
carburetor is run dry. Allow the engine to run out of fuel with the fuel tap switched off.

13
Verticut T.T. SP20007_REV_0
*HQHUDO/XEULFDWLRQ
5($552//(5
PRQWK
A grease point is located under the belt guard on the side plate of the machine. This is to lubricate the internal spur gear
that provides drive to the rear roller.Apply one pump of grease. Do not over grease.
&21752//(9(56$1'&$%/(6
PRQWKV
Apply a small amount of oil to the control cables. Flow down the protective cables can be assisted by operating the lever
a few times after lubricating.
)521752//(5$'-867(56
PRQWKV
Apply a small quantity of copper grease or similar to the adjuster studs to prevent corrosion and ease adjustment.

14
Verticut T.T. SP20007_REV_0
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
1 194946 Chain Case Screw 1
2 229000 Support Plate 1
3 229004 Engine Bearers 2
4 229005 Cable Stop 2
5 229006 Belt Guide Roller Clutch Top 1
6 229007 Belt Guide Roller Clutch Pulley 1
7 229035 Brake Bracket 1
8 229089 20” Tie Bar 1
9 229115 Chain Case Stud 2
10 229153 Clamp Plate Assy 1
11 229492 Retaining Plate Assy 1
12 230370 Side Plate L.H. Verticut T.T. 1
13 230371 Side Plate R.H. Verticut T.T. 1
14 229737 Belt Guide Assy 1
15 229742 Buffer 2
16 229744 Belt Guide 1
17 229746 Hex Collar 1
18 229747 Guard Bracket 1
19 229748 Quadrant Pivot Stud 2
20 229811 20” Engine Bed (Simplex) 1
21 229815 20” Rear Roller Scraper 1
22 229846 Buffer Block 2
23 230004 Support Bracket 1
24 J20064 Grease Nipple 1/4” UNF 1
25 J20235 20” Front Cross Bar 1
26 J20292 Collar Front Tie Bar 2
27 J20297 Serial Number Plate 1
28 J209111 Bush Quadrant 2
29 SP01008 Hex Set Screw M6 x 16 12
30 SP01009 Hex Set Screw M8 x 20 8
31 SP01016 Button Head M6 x 12 2
32 SP01025 Cap Head M8 x 30 4
33 SP01027 Hex Set Screw M8 x 40 2
34 SP01035 Hex Set Screw M10 x 25 10
35 SP01053 Hex Set Screw 1/2” Unf x 1” 2
36 SP02004 Nut M6 Nyloc 8
37 SP02005 Nut M8 Std 2
38 SP02006 Nut M8 Nyloc 10
  &KDVVLV0DLQ$VVHPEO\
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
39 SP02008 Nut M10 Nyloc 1
40 SP03003 Washer M6 Toothed 4
41 SP03004 Washer M8 Toothed 2
42 SP03005 Washer M10 Toothed 8
43 SP03007 Washer M6 x 18 2
44 SP03008 Washer M8 Form A 6
45 SP03010 Washer M6 Form A 10
46 SP03011 Washer M10 Form A 3
47 SP03016 Washer M10 Form C 2
48 SP05001 Rivet 4.8 x 10 2
49 J20236 20” Lower Unit Tie Bar 1
48
25
31
36
26
35
28
46
39
13
40
29
34
42
21
27
44
30
10 38
11
19
41
44 30
8
4
47
29
30
44
15
22
30
19
14
12 24 29
40
34
42
26
31
36
16
9
30
28
46 18 1
46
17
35
15
4
22
38
10
28
32
47
34
36
43
7
33
3
20
44
38
38
44
23
11
630
41 5
36
29
2
49

15
Verticut T.T. SP20007_REV_0
2.01 'ULYH0DLQ$VVHPEO\
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
1 73445 Key 3/16” x 3/16” x 2 1/4” Rd End 1
2 228001 Tapered Bush 1610 - 3/4” 1
3 228002 Tapered Bush 1108 - 3/4” 1
4 228004 Pulley SPZ-71 1
5 228005 Pulley SPZ-132 1
6 228007 Belt V X10-665 LP 1
7 228009 Brake Caliper 1
8 228011 Coupling Half (3/4”) 1
9 228012 Belt Ribbed 4PK 698 1
10 228103 Coupling Element 1
11 229001 20” Layshaft Cutter Drive 1
12 229247 20” Layshaft Roller Drive 1
13 229009 Drive Idler Arm 1
14 229013 Pulley Spacer 1
15 229014 Belt Guide Peg 2
16 229036 Brake Disc 1
17 229038 Tensioner Pulley 1
18 229040 Pulley A Section 56mm 1
19 229043 Cutter Idler Arm 1
20 229044 Idler Lever 2
21 229090 20” Layshaft Guard 2
22 229091 Bearing Housing 4
23 229092 Bearing Spacer 3
24 229322 4 Groove Drive Pulley 1
25 229382 Brg Housing 2
26 229706 Cylinder Spacer Simplex 1
27 229750 Belt X13 850 V-Belt 1
28 229751 Pulley SPA 106 X1 1
29 229752 Tapered Bush 1610 - 3/4” 1
30 230460 Top Drive Spacer (Simplex) 1
31 REF. 2.03 Engine Assy 1
32 BA1011 Key 1/4” x 1/4” x 3/4” Rd End 1
33 REF. 1.01 Chassis Assy 1
34 J20023 Unit Limiting Stud 2
35 J20052 Bearing 6204-2RS 3 4
36 J20457 Key 3/16” x 3/16” x 1” Rd End 1
222
39
48
33
21
33
6
33
5
25
13 45 50
17 10
33
7
51
49
16
12
33
19
20
25
54
47
45
27 29 28
42
41
33
24
46
51
25 40
19
15
31
9
20
40
18
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
37 J20467 Grub Screw M8 x 8 3
38 J209030 Key 3/16” x 3/16” x 3/4” Rd End 2
39 J209043 Tensioner Back Plate 1
40 J209047 Tensioner Pulley 2
41 J209249 Washer 9 x 35 x 3 2
42 SP01009 Hex Set Screw M8 x 20 15
43 SP01027 Hex Set Screw M8 x 40 4
44 SP01068 Hex Set Screw 3/8” UNF x 2 1/2” 1
45 SP01071 Hex Set Screw 3/8” UNF x 1 1/2” 2
46 SP01076 Hex Set Screw M8 x 16 1
47 SP02006 Nut M8 Nyloc 4
48 SP02018 Nut 3/8” UNF Nyloc 1
49 SP02029 Nut M16 Lock (Thin) 1
50 SP02033 Nut 3/8” Unf Lock (Thin) 1
51 SP02034 Nut 3/4” UNF Std 2
52 SP03002 Washer 3/8” 2
53 SP03004 Washer M8 Toothed 15
54 SP03008 Washer M8 Form A 2
55 SP03015 Washer M8 Form C 1

16
Verticut T.T. SP20007_REV_0
2.02 'ULYH0DLQ$VVHPEO\
24
41
32
29
28
27
26
22
23
35
35
23
9
38
1221
22
37
18
38
2
5
37
4
6
8
1
22
35
27
21
30
36
35
22
27
3
11
31
A-A
C-C
B-B
C
C
A
A
B
B
10
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
1 73445 Key 3/16” x 3/16” x 2 1/4” Rd End 1
2 228001 Tapered Bush 1610 - 3/4” 1
3 228002 Tapered Bush 1108 - 3/4” 1
4 228004 Pulley SPZ-71 1
5 228005 Pulley SPZ-132 1
6 228007 Belt V X10-665 LP 1
7 228009 Brake Caliper 1
8 228011 Coupling Half (3/4”) 1
9 228012 Belt Ribbed 4PK 698 1
10 228103 Coupling Element 1
11 229001 20” Layshaft Cutter Drive 1
12 229247 20” Layshaft Roller Drive 1
13 229009 Drive Idler Arm 1
14 229013 Pulley Spacer 1
15 229014 Belt Guide Peg 2
16 229036 Brake Disc 1
17 229038 Tensioner Pulley 1
18 229040 Pulley A Section 56mm 1
19 229043 Cutter Idler Arm 1
20 229044 Idler Lever 2
21 229090 20” Layshaft Guard 2
22 229091 Bearing Housing 4
23 229092 Bearing Spacer 3
24 229322 4 Groove Drive Pulley 1
25 229382 Brg Housing 2
26 229706 Cylinder Spacer Simplex 1
27 229750 Belt X13 850 V-Belt 1
28 229751 Pulley SPA 106 X1 1
29 229752 Tapered Bush 1610 - 3/4” 1
30 230460 Top Drive Spacer (Simplex) 1
31 REF. 2.03 Engine Assy 1
32 BA1011 Key 1/4” x 1/4” x 3/4” Rd End 1
33 REF. 1.01 Chassis Assy 1
34 J20023 Unit Limiting Stud 2
35 J20052 Bearing 6204-2RS 3 4
36 J20457 Key 3/16” x 3/16” x 1” Rd End 1
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
37 J20467 Grub Screw M8 x 8 3
38 J209030 Key 3/16” x 3/16” x 3/4” Rd End 2
39 J209043 Tensioner Back Plate 1
40 J209047 Tensioner Pulley 2
41 J209249 Washer 9 x 35 x 3 2
42 SP01009 Hex Set Screw M8 x 20 15
43 SP01027 Hex Set Screw M8 x 40 4
44 SP01068 Hex Set Screw 3/8” UNF x 2 1/2” 1
45 SP01071 Hex Set Screw 3/8” UNF x 1 1/2” 2
46 SP01076 Hex Set Screw M8 x 16 1
47 SP02006 Nut M8 Nyloc 4
48 SP02018 Nut 3/8” UNF Nyloc 1
49 SP02029 Nut M16 Lock (Thin) 1
50 SP02033 Nut 3/8” Unf Lock (Thin) 1
51 SP02034 Nut 3/4” UNF Std 2
52 SP03002 Washer 3/8” 2
53 SP03004 Washer M8 Toothed 15
54 SP03008 Washer M8 Form A 2
55 SP03015 Washer M8 Form C 1

17
Verticut T.T. SP20007_REV_0
2.03 'ULYH(QJLQH$VVHPEO\
,WHP1R 3DUW1XPEHU 'HVFULSWLRQ 4XDQWLW\
1 228001 Tapered Bush 1610 - 3/4” 1
2 228011 Coupling Half (3/4”) 1
3 229015 Flywheel 1
4 229901 Engine 5.5 Hp Honda GX160 Q9 Type 1
5 J20467 Grub Screw M8 x 8 1
6 J209025 Key 3/16” x 3/16” x 1 3/4” Rd End 1
7 SP01079 Grub Screw 3/8” x 5/8” 2
3
6
2
1
5
4
7

18
Verticut T.T. SP20007_REV_0
3.01 Rear5ROOHU0DLQ$VVHPEO\
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
1 62662 Bearing 6205-2RS 3 1
2 229031 Dirt Excluder 1
3 229039 Landroll Collar 1
4 229104 Landroll Bearing Housing 1
5 REF. 3.03 Drive Bearing Housing Assy 1
6 REF. 3.02 Rear Roller Assy 1
7 J20009 Blanking Plate 1
8 SP01045 Hex Set Screw M8 x 25 8
9 SP02028 Nut M16 Nyloc 1
10 SP03004 Washer M8 Toothed 8
1
10
8
7
4
8
8
9
2
10
6
3
5

19
Verticut T.T. SP20007_REV_0
 5HDU5ROOHU5ROOHU$VVHPEO\
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
1 228049 Key 1/4” x 1/4” x 1 1/4” Rd End 1
2 229022 30 Tooth Bevel Gear 2
3 229023 Bush Oilite MBC AJ2024 x 1.5 4
4 229025 20 Tooth Bevel Gear 2
5 229030 Internal Gear 1
6 229032 Roller Locking Collar 1
7 230485 20” LH Rear Roller (Smooth) 1
8 230486 20” RH Rear Roller (Smooth) 1
9 800170 20” Rear Roller Shaft Assy 1
10 J20467 Grub Screw M8 x 8 1
11 J209249 Washer 9 x 35 x 3 2
12 SP01012 Button Head M8 x 12 2
A
A
16
10
3
8
2
2
3
9
3
7
5

20
Verticut T.T. SP20007_REV_0
  5HDU5ROOHU'ULYH%HDULQJ+RXVLQJ$VVHPEO\
,WHP1R 3DUW1R 'HVFULSWLRQ 4XDQWLW\
1 062662 Bearing 6205-2RS 3 1
2 228053 Pin Spirol M5 x 45 1
3 229003 Drive Pulley Land Roll 1
4 229011 Pinion Shaft 11T 1
5 229033 Roller Bearing Housing Oblong 1
6 J20052 Bearing 6204-2RS 3 2
4
2
3
6
1
6
5