Denon AVR-4308 User manual

AV SURROUND RECEIVER
AVR-4308
GraphicalUserInterface
English
Use this manual in combination with the operating
guide displayed on the GUI screen.
GUI Menu Operation (vpage 24)
GUI Menu Map (vpage 25)
Language (vpage 38)
Remote Control Unit Operations (vpage 62)
Owner’s Manual

I
nSAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCETHE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
R&TTE Directive 1999/5/EC
This product may be operateded in the following countries;
AT BE CZ DK FI
FR DE GR HU IE
IT NL PL PT SK
ES SE GB NO CH
DENON EUROPE
Division of D&M Germany GmbH
An der Landwehr 19, Nettetal,
D-41334 Germany
DECLARATION OF CONFORMITY
Hereby, D&M Holdings Inc., Denon Brand Company declares that this
product AVR-4308 is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC, in conformity with the
following standards;
EN60065, EN55013, EN55020, EN55022, EN55024, EN61000-3-2,
EN61000-3-3, EN300328, EN301489-01, EN301489-17 and EN50385
The declaration of conformity may be consulted to our European
representative, DENON EUROPE.
• Avoid high temperatures.
Allow for sufficient heat dispersion when installed in a rack.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Keep the unit free from moisture, water, and dust.
• Unplug the power cord when not using the unit for long
periods of time.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Do not let foreign objects into the unit.
• Do not let insecticides, benzene, and thinner come in
contact with the unit.
• Never disassemble or modify the unit in any way.
nNOTE ON USE
CAUTION:
• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the unit.
• Observe and follow local regulations regarding battery disposal.
• Do not expose the unit to dripping or splashing fluids.
• Do not place objects filled with liquids, such as vases, on the unit.
A NOTE ABOUT RECYCLING:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local recycling
regulations.
When discarding the unit, comply with local rules or regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning battery disposal.
This product and the supplied accessories, excluding the batteries, constitute the applicable product according to the WEEE directive.
1.IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets R&TTE directive requirements. Modification of the product could
result in hazardous Radio and EMC radiation.
2.CAUTION
• Separation distance of at least 20 cm must be maintained between the antenna of this product and all persons.
• This product and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.


Accessories······················································································ 3
Cautions on Handling·····································································3
Cautions on Installation·································································3
About the Remote Control Unit····················································4
Inserting the Batteries····································································4
Operating Range of the Remote Control Unit································ 4
Part Names and Functions·····························································5
Front Panel ·····················································································5
Display ···························································································5
Rear Panel ······················································································6
Remote Control Unit ······································································ 7
Getting Started
Preparations ····················································································8
Cables Used for Connections ························································8
Video Conversion Function····························································· 9
Speaker Connections ··································································· 10
Speaker Installation······································································ 10
Speaker Connections ······························································10, 11
Connecting Equipment with HDMI connectors························· 12
Connecting the Monitor······························································· 13
Connecting the Playback Components ······································ 13
DVD Player ··················································································· 13
Record Player ··············································································· 14
CD Player ····················································································· 14
iPod®···························································································· 14
TV/CABLE Tuner ··········································································· 15
Satellite Receiver ········································································· 15
Connecting the Recording Components ···································· 16
Digital Video Recorder·································································· 16
Video Cassette Recorder ····························································· 16
CD Recorder / MD Recorder / Tape Deck ····································· 17
Connections to Other Devices····················································· 17
Components Equipped with a DENON LINK connector ·············· 17
Video Camera / Game Console ···················································· 18
Component with Multi-channel Output connectors····················· 18
External Power Amplifier······························································ 18
USB Port ······················································································ 19
Antenna terminals ·······································································20
Network Audio ·············································································21
Multi Zone···················································································· 22
External Controller ·······································································22
Connecting the Power Cord·························································23
Once Connections are Completed ··············································23
Connections
Preparations ··················································································26
Auto Setup ····················································································27
aAuto Setup ··············································································27
Error Messages·······································································28
sOption ·····················································································28
dParameter Check·····································································28
Auto Setup
Input Source Selection·································································39
Settings Related to Playing Input Sources·································39
aPlay ·························································································39
sAuto Preset ·············································································39
dPreset Skip··············································································39
fPreset Name ··········································································· 40
gInput Mode ·············································································40
hRename···················································································40
jOther·······················································································40
kPlayback Mode (iPod)······························································41
lAssign ···············································································41, 42
A0 Playback Mode········································································ 42
A1 Still Picture ··············································································42
Source Select
Zone Setup····················································································35
aZONE2 ····················································································35
sZONE3 ····················································································35
Option Setup·················································································36
aAmp Assign·············································································36
sVolume Control ······································································· 36
dSource Delete ·········································································36
fGUI····················································································36, 37
gQuick Select Name ·································································37
hTrigger Out 1 ··········································································· 37
jTrigger Out 2 ··········································································· 37
kDigital Out···············································································37
lRemote ID···············································································37
A0 2Way Remote ·········································································37
A1 Dimmer···················································································38
A2 Setup Lock ··············································································38
A3 Maintenance Mode·································································38
A4 Firmware Update ····································································38
Language·······················································································38
Contents
Speaker Setup···············································································29
aSpeaker Configuration·····························································29
sSubwoofer Mode ····································································29
dDistance··················································································29
fChannel Level··········································································30
gCrossover Frequency ······························································30
hSurround Speaker ···································································30
HDMI Setup···················································································31
ai/p Scaler ·················································································31
sResolution ···············································································31
dProgressive Mode···································································31
fAspect·····················································································31
gColor Space·············································································31
hRGB Range ·············································································31
jAuto Lip Sync ··········································································31
kAudio·······················································································31
lMonitor Out ············································································31
Audio Setup ··················································································32
aEXT. IN Setup ··········································································32
s2ch Direct/Stereo ····································································32
dDownmix Option·····································································32
fAuto Surround Mode ······························································32
gManual EQ ··············································································33
Network Setup·············································································· 33
aNetwork Setup··································································33, 34
sOther·······················································································35
dNetwork Information·······························································35
Manual Setup
Example of the Display of the GUI Mark at a Title·····················24
Example of Display of Default Values ·········································24
Examples of GUI Screen Displays ···············································24
Example: Browse Menu (Top Menu)············································24
Example: Menus with Illustrations (Auto Setup)··························24
Cursor Position Display ································································ 24
Operations·····················································································24
GUI Menu Map··············································································25
GUI Menu Operations


Status ····························································································47
aMAIN ZONE············································································47
sZONE2/3/4 ··············································································47
Audio Input Signal········································································48
HDMI Information ·········································································48
aSignal Information ··································································· 48
sMonitor1 ·················································································48
dMonitor2 ·················································································48
Auto Surround ··············································································48
Quick Select ··················································································48
Preset Station ··············································································· 48
Information
Playback
Main Remote Control Unit···························································62
Operating DENON Audio Components········································62
Presetting·····················································································62
Operating Preset Components ············································62 ~ 64
Setting the Remote ID ·································································65
Learning Function·········································································65
System Call Function···································································· 66
Punch Through Function·······························································66
Setting the Time the Backlight Stays Lit·······································67
Adjusting the Backlight’s Brightness············································67
Resetting the Main Remote Control Unit·····································67
Sub Remote Control Unit Operations ·································· 68, 69
Switching Zones···········································································70
Setting the Zone for Which the Sub Remote Control Unit is Used
(ZONE SELECT LOCK Mode)·······················································70
Setting the Remote ID ·································································70
Resetting the Settings·································································· 70
Remote Control Unit Operations
Multi-Zone Settings with the Amp Assign Function·········71 ~ 74
Multi-Zone Settings and Operations with Zone Pre-out Output ··· 74
Multi-Zone Operations·································································75
Turning the Power On and Off······················································75
Selecting the Input Source···························································75
Adjusting the Volume ···································································75
Turning off the Sound Temporarily················································ 75
Amp Assign / Multi-Zone Connections and Operations
Troubleshooting···································································88 ~ 91
Specifications········································································· 91, 92
Other Information································································ 76 ~ 87
Other Operations··········································································59
Playing Super Audio CD ·······························································59
Recording on an External Device (REC OUT mode)·····················60
Convenient Functions ··································································61
Channel Level···············································································61
Fader Function ············································································· 61
Quick Select Function ··································································61
Personal Memory Plus Function ··················································61
Last Function Memory·································································61
Backup Memory···········································································61
Resetting the Microprocessor······················································61
Other Operations and Functions
List of preset codes ··········································· End of this manual
Preparations ··················································································49
Turning the Power On ··································································49
Operations During Playback ·························································49
Playing Video and Audio Equipment···········································49
Basic Operation············································································49
Listening to FM/AM Broadcasts ················································· 50
Basic Operation············································································50
Presetting Radio Stations (Preset Memory)·································50
Listening to Preset Stations·························································51
RDS (Radio Data System) ····························································51
RDS Search ··················································································51
PTY Search···················································································52
TP Search ·····················································································52
RT (Radio Text)··············································································53
iPod®Playback ·············································································53
Basic Operation············································································53
Listening to Music ·······································································54
Viewing Still Pictures or Videos on the iPod·································54
Playing Network Audio or USB Memory Devices······················55
Basic Operation············································································56
Listening to Internet Radio···························································57
Presetting Internet Radio Stations ··············································· 57
Registering Internet Radio Stations as Your Favorites··················57
Playing Files Stored on a Computer·············································58
Playing Files Stored on USB Memory Devices ······················58, 59
Operating the AVR-4308 Using a Browser (Web control) ············59
Audio······························································································ 44
aSurround Parameters ······················································44 ~ 46
sTone ························································································46
dRoom EQ ················································································ 46
fRESTORER··············································································46
gNight Mode·············································································47
hAudio Delay·············································································47
Picture Adjust················································································ 47
aContrast ··················································································47
sBrightness···············································································47
dChroma Level··········································································47
fHue ·························································································47
Parameter
Standard Playback········································································43
Surround Playback of 2-channel Sources ·····································43
Playing Multi-channel Sources (Dolby Digital, DTS, etc.) ············· 43
DSP Simulation Playback·····························································43
Stereo Playback ············································································44
Direct Playback ·············································································44
Playback in the PURE DIRECT Mode···········································44
Surround Modes


Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Check that the following parts are supplied with the product.
qOwner’s manual ...................................................................... 1
wService station list ................................................................... 1
ePower cord (Cord length: Approx. 1.5 m)................................. 1
rMain remote control (RC-1068) ............................................... 1
tLR6/AA batteries (for RC-1068)................................................ 2
ySub remote control (RC-1070) ................................................. 1
uR03/AAA batteries (for RC-1070) ............................................. 2
iFM indoor antenna .................................................................. 1
oAM loop antenna ..................................................................... 1
Q0 Rod antenna for wireless LAN connection .............................. 1
Q1 Setup microphone (Cord length: Approx. 7.6 m)...................... 1
e r y
i Q1Q0o
Thank you for purchasing this DENON product. To ensure proper
operation, please read these owner’s manual carefully before using
the product.
After reading them, be sure to keep them for future reference.
Getting Started
Accessories
• Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
• Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
• About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
• Moving the unit
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units before
moving the unit.
• Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
Note:
For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
bNote
b
Wall
b
b
Cautions on Handling Cautions on Installation
Getting Started


Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
In addition to the AVR-4308, the included main remote control unit
(RC-1068) can also be used to operate the equipment listed below.
q DENON system components
w Non-DENON system components
• By setting the preset memory (vpage 62 ~ 64)
• By using the learn function (vpage 65)
qLift the clasp and remove the rear lid.
ePut the rear cover back on.
(RC-1068) (RC-1070)
(RC-1068) (RC-1070)
LR6/AA
R03/AAA
30°
30°
Approx. 7 m
or
(RC-1068)
(RC-1070)
wLoad the two batteries properly as indicated by the marks in the
battery compartment.
About the Remote Control Unit
Inserting the Batteries
NOTE
• Replace the batteries with new ones if the set does not operate even
when the remote control unit is operated close to the unit.
• The supplied batteries are only for verifying operation.
• When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not attempt to charge dry batteries.
• Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
• If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
• Remove the batteries from the remote control unit if it will not be in
use for long periods.
• When replacing the batteries, have the new batteries ready and
insert them as quickly as possible.
Operating Range of the Remote Control
Unit
Point the remote control unit at the remote sensor when operating it.
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
Getting Started


Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
For buttons not explained here, see the page indicated in parentheses ( ).
w e
to i u y
q r
Q3Q2Q1Q0
qPower operation button
(ON/STANDBY) ··········································· (49)
wPower indicator··········································· (49)
ePower switch (hON jOFF) ····················· (49)
rQUICK SELECT buttons / indicators········· (61)
tMASTER VOLUME control knob·········· (49, 75)
yMaster volume indicator
uDisplay
iRemote control sensor································· (4)
oSOURCE SELECT knob······························· (39)
Q0 SOURCE button ·········································· (39)
Q1 TUNING PRESET button ···························· (51)
Q2 ZONE 2/3/4 / REC SELECT button······ (60, 75)
Q3 VIDEO SELECT button ······························· (40)
Q4 Headphones jack (PHONES)······················ (49)
Q5 ZONE2 ON/OFF button ······························ (75)
Q6 ZONE3 ON/OFF button ······························ (75)
Q7 ZONE4 ON/OFF button ······························ (75)
Q8 MENU button·············································· (24)
Q9 Cursor buttons (uio p)·························· (24)
W0 CH SEL / ENTER button ······················· (24, 61)
W1 RETURN button ·········································· (24)
W2 V.AUX INPUT connectors··························· (18)
W3 SETUP MIC jack ·········································· (26)
W4 ROOM EQ button········································ (46)
W5 DIMMER button ·········································· (38)
W6 USB port······················································ (19)
W7 STATUS button ··········································· (48)
t
uQ3Q7Q8 iQ0oQ5 Q1 Q2Q4Q6 y
wq e r
qInput signal indicators
wInput signal channel indicators
These light when digital signals are input.
eInformation display
The input source name, surround mode, setting
values and other information are displayed here.
rOutput signal channel indicators
tSurround speaker indicators
These light according to the settings of the
surround A and B speakers.
yMonitor output indicators
These light according to the HDMI monitor
output setting. When set to “Auto (Dual)”, the
indicators light according to the connection
status.
uMaster volume indicator
iAUDYSSEY MULTEQ XT indicator
This lights when the room equalizer is selected.
oRecording output source indicator
This lights when the REC OUT mode is
selected.
Q0 NIGHT indicator
This lights when the night mode is selected.
Q1 Multi zone indicators
These light when the power for the respective
zone is turned on.
Q2 RESTORER indicator
This lights when the RESTORER mode is
selected.
Q3 ADVANCED AL24 indicator
This lights when Advanced AL24 Processing is
activated (vpage 78).
Q4 D.LINK indicator
This lights when playing using DENON LINK
connections.
Q5 Input mode indicators
Q6 HDMI indicator
This lights when playing using HDMI
connections.
Q7 Decoder indicators
These light when the respective decoders are
operating.
Q8 Tuner reception mode indicators
These light according to the reception conditions
when the input source is set to “TUNER”.
• AUTO
This lights when in the auto tuning mode.
• RDS
This lights when receiving RDS broadcasts.
• STEREO
In the FM mode, this lights when receiving
analog stereo broadcasts.
• TUNED
This lights when the broadcast is properly tuned
in.
Part Names and Functions
Front Panel Display
W2 W3
W4W7E2 W5W6 E3 E0E1 W8W9
Q4 Q5 Q6 Q7 Q8 W1W0Q9
GWith the door openH
E1 PURE DIRECT button·································· (44)
E2 DSP SIMULATION button ·························· (43)
E3 STANDARD button ····································· (43)
W8 INPUT MODE button ·································· (40)
W9 RESTORER button ······································ (46)
E0 DIRECT/STEREO button····························· (44)
Getting Started


Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
Q8 Q8Q9Q7 Q7
te
oQ0Q1Q2
Q5 iQ3Q4
qy urw
W0
Q8Q9Q7
Q6
Q7Q8
qRS-232C connector····································· (22)
wTRIGGER OUT jacks ··································· (22)
eFM/AM antenna terminals
(TUNER ANTENNA)···································· (20)
rDOCK CONTROL jack ································· (14)
tSpeaker terminals (SPEAKERS) ················ (10)
yAC OUTLET ················································· (23)
uAC inlet (AC IN)··········································· (23)
iDigital audio connectors
(OPTICAL / COAXIAL) ·························· (13, 15)
oWLAN ANTENNA terminal························· (21)
Q0 ETHERNET connector································· (21)
Q1 USB port······················································ (19)
Q2 DENON LINK connector····························· (17)
Q3 COMPONENT VIDEO connectors ·············· (13)
Q4 HDMI connectors········································ (12)
Q5 VIDEO / S-VIDEO connectors···················· (13)
Q6 REMOTE CONTROL jacks··························· (22)
Q7 Analog audio connectors (AUDIO)············ (13)
Q8 PRE OUT connectors···························· (18, 22)
Q9 EXT. IN connectors ····································· (18)
W0 SIGNAL GND terminal ······························· (14)
Rear Panel
Getting Started


Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
q
i
w
e
r
t
y
u
o
Q1
Q3
Q4
Q2
Q0
Q5
Q6
Q7
Q9
W0
W2
W5
W7
W6
W4
W3
W1
Q8
tSystem buttons ···································· (63, 64)
yAudio delay button (A. DL) ························ (47)
uTuner system buttons ································ (50)
iInput mode button (INPUT)······················· (40)
oMENU button·············································· (24)
Q0 Cursor buttons (uio p)························· (24)
Q1 Parameter / Search button
(PARA / SRCH) ································ (44, 51, 54)
Q2 Monitor select (M. SEL) /
HOME button ········································ (31, 62)
Q3 Channel buttons (CH)································· (50)
Q4 Input source select /
Number buttons ··································· (39, 50)
Q5 Remote control signal transmitter·············· (4)
Q6 Device select indicators (DEV1 / DEV2) ··· (62)
Q7 ZONE3 / ZONE4 select indicators
(Z3 / Z4) ······················································· (75)
Q8 RESTORER button (RSTR)·························· (46)
Q9 Night button (NGT) ···································· (47)
W0 Test tone button (TEST) ····························· (30)
W1 Surround speaker select button (SPKR)··· (30)
W2 POWER buttons ·········································· (49)
W3 Channel select (CH SEL) /
ENTER button ······································· (24, 61)
W4 Return button (RTN)··································· (24)
W5 Master volume control buttons
(VOL)······················································ (49, 75)
W6 Muting button (MUTE)························· (49, 75)
W7 Main remote control unit setup button
(RC SETUP) ················································· (62)
q
r
t
y
i
o
Q0
u
e
w
Q4
Q7
Q8
Q9
W0
Q6
Q5
Q2
Q3
Q1
qZONE indicators·········································· (70)
wAdvanced setup button······························ (70)
eInput source select buttons······················· (39)
rCHANNEL buttons······································ (50)
tSHIFT button··············································· (50)
yMENU button·············································· (24)
uCursor buttons (uio p)························· (24)
iSEARCH button ···································· (51, 54)
oREPEAT button············································ (54)
Q0 RANDOM button ········································ (54)
Q1 Remote control signal transmitter·············· (4)
Q2 ZONE SELECT button································· (70)
Q3 Zone power on/off buttons
(ZONE ON / ZONE OFF) ····························· (75)
Q4 Master volume control buttons
(VOLUME) ············································ (49, 75)
Q5 Muting button (MUTE)························· (49, 75)
Q6 ENTER button ············································· (24)
Q7 RETURN button ·········································· (24)
Q8 System buttons ······························ (50, 68, 69)
Q9 ALL MUSIC/FAVORITES
(DIRECT PLAY) button ······························· (68)
W0 USB (DIRECT PLAY) button························ (68)
nMain remote control unit (RC-1068) nSub remote control unit (RC-1070)
The time for which the backlight stays on can
be changed (vpage 67 “Setting the Time the
Backlight Stays Lit”).
Remote Control Unit
NOTE
The SAT TU, DTU, ZONE2 mode QUICK SELECT
(1 ~ 3), A. DL, RSTR, NGT, INPUT, SPKR, TEST and
surround mode buttons cannot be used.
NOTE
The AUX-1, AUX-2, AUX-3, SAT TU, DTU, DVR-2
and OPTION buttons cannot be used.
qSignal transmission indicator ··················· (62)
wMode select buttons ·································· (62)
eQuick select / System call buttons ····· (61, 66)
rSurround mode buttons ······················ (43, 44)
Getting Started


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
Audio cables Video cables
Coaxial digital connections
(Orange)
Coaxial digital (75 Ω/ohms pin-plug) cable
Optical digital connections
Optical cable
Analog connections (stereo)
(White)
(Red)
R
L
R
L
Stereo pin-plug cable
Analog connections (monaural, for subwoofer)
(Black)
Pin-plug cable
DENON LINK connections
DENON LINK cable
Speaker connections
Speaker cables
Network connections (wired LAN)
Ethernet cable
Component video connections
(Green)
(Blue)
(Red)
(Y)
(PB/CB)
(PR/CR)
Component video cable
S-Video connections
S-Video cable
Video connections
(Yellow)
75 Ω/ohms pin-plug video cable
Audio and video cables
HDMI connections
19-pin HDMI cable
Signal direction
Audio signal: Video signal:
Output
Input
Input
Output
Output
Input
Input
Output
Connections
NOTE
• Do not plug in the power cord until all connections have been
completed.
• When making connections, also refer to the operating instructions of
the other components.
• Be sure to connect the left and right channels properly (left with left,
right with right).
• Do not bundle power cords together with connection cables. Doing
so can result in humming or noise.
Connections for all compatible audio and video signal formats are
described in these operating instructions. Please select the types
of connections suited for the equipment you are connecting.
With some types of connections, certain settings must be made
on the AVR-4308. For details, refer to the instructions for the
respective connection items below.
Cables Used for Connections
Select the cables according to the equipment being connected.
Preparations
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
GFlow of video signals for ZONE2H
• This function automatically converts various formats of video signals input to the AVR-4308 into the
format used to output the video signals from the AVR-4308 to a monitor.
• The AVR-4308’s video input/output circuitry is compatible with the following four types of video signals:
Digital video signals: HDMI
Analog video signals: Component video, S-Video and Video
Video Conversion Function
GFlow of video signals inside the AVR-4308H
Main zone
High picture
quality playback HDMI connector
Component video
connectors
S-Video connector
Video connector
Monitor
HDMI connector
Component video
connectors
S-Video connector
Video connector
Video inputs Video outputs
: When 480i/576i signals are input in the main zone
Component video
connectors
S-Video connector
Video connector
Component video
connectors
Video connector
Video inputs Video outputs
ZONE2
NOTE
• HDMI signals cannot be converted into analog signals.
• 1080p component input video signals cannot be output to anything other than component video
connectors.
• 480p/576p, 1080i and 720p component video input signals cannot be converted into S-Video or Video
format.
• When using the component video output connectors for connection to the ZONE2 monitor, the ZONE2’s
on-screen display is not displayed.
• When a non-standard video signal from a game machine or some other source is input, the video
conversion function might not operate.
• When not using this function, connect a monitor output with the same type of connector as the video
input connector.
• The resolution of the HDMI input-compatible monitor connected to the AVR-4308 can be checked at GUI
menu “Information” – “HDMI Information” – “Monitor1” or “Monitor2” (vpage 48).
High picture
quality playback
ZONE2
monitor
Connections

0
Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
Speaker Connections
w q
w q w q
w q w q w q w q
w q */
w q
(L)
(R)
(L) (R) (L) (R)
(R)
(L)
The illustration below shows a basic example of installation of the amplifier combined with 8 speakers and
a monitor.
Speaker Installation
Subwoofer Center speaker
Surround speakers
Front speakers
Place the front speakers to the
sides of the monitor or screen and
as flush with the screen surface as
possible.
The table below shows a typical speaker configuration for the AVR-4308.
Surround back speakers
FRONT
CENTER
SURROUND
A
SURROUND
B
SURROUND
BACK SUBWOOFER
L R L R L R L R 1
only
7.1-channels
(Surround A+B) S S S S S S S S S –S
7.1-channels S S S S S – – S S –S
6.1-channels S S S S S – – – – S S
5.1-channels S S S S S – – – – – S
3.1-channels S S S – – – – – – – S
2.1-channels S S – – – – – – – – S
2-channels S S – – – – – – – – –
Speaker Connections
Example: 7.1-channels (Surround A+B)
Front speakers Surround back
speakers
Center speaker Subwoofer
Subwoofer
with built-in
amplifier
Surround speakers
A
Surround speakers
B
When using just one surround back speaker, connect it to the left channel (SBL).
bL : Left
R : Right
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
Connecting the Speaker Cables
Carefully check the left (L) and right (R) channels and + (red) and –
(black) polarities on the speakers being connected to the AVR-4308,
and be sure to interconnect the channels and polarities correctly.
1Peel off about 10 mm of sheathing from the tip of the speaker cable, then either
twist the core wire tightly or terminate
it.
2Turn the speaker terminal counterclockwise to loosen it.
3Insert the speaker cable’s core wire to the hilt into the speaker terminal.
4Turn the speaker terminal clockwise to tighten it.
NOTE
• Use speakers with an impedance of 6 to 16 Ω/ohms. When using
surround A and B speakers simultaneously, use speakers with an
impedance of 8 to 16 Ω/ohms.
• Connect the speaker cables in such a way that they do not stick out
of the speaker terminals. The protection circuit may be activated if
the core wires touch the rear panel or if the + and – sides touch each
other (v“Protection circuit”).
• Never touch the speaker terminals while the power supply is
connected. Doing so could result in electric shock.
Protection circuit
If speakers with an impedance lower than specified (for example
4 Ω/ohms speakers) are used for an extended period of time with
the volume turned up high, the temperature may rise, activating the
protection circuit.
When the protection circuit is activated, the speaker output is shut
off and the power indicator flashes red. If this happens, unplug
the power cord, then check the speaker cable and input cable
connections. If the set is extremely hot, wait for it to cool off and
improve ventilation around it. Once this is done, plug the power cord
back in and turn the set’s power back on.
If the protection circuit is activated again even though there are no
problems in the ventilation around the set nor in the connections,
the set may be damaged. Turn the power off, then contact a DENON
service center.
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
With HDMI connections, the video and audio signals can be transferred with a single cable.
065
)%.*
*/
)%.*
Compatible
audio format Details Discs (examples)
2-channel linear
PCM
2ch 32-192 kHz
16/20/24 bits
CD, DVD-Video,
DVD-Audio
Multi-channel
linear PCM
8ch 32-192 kHz
16/20/24 bits DVD-Audio
Dolby Digital, DTS Bitstream DVD-Video
DSD
2/5.1ch
2.8224 MHz
1 bit
SACD
Dolby Digital Plus,
Dolby TrueHD,
DTS-HD
Bitstream HD DVD,
Blu-ray Disc
MonitorDVD player bThe AVR-4308 is equipped for HDMI version 1.3a. This
version is compatible with other versions, allowing
connection to all components equipped with an HDMI
connector.
bThe AVR-4308 is compatible with 30- and 36-bit Deep
Color.
Copyright protection system (HDCP)
In order to play the digital video and audio signals of a DVD-
Video or DVD-Audio disc using HDMI/DVI connections, both
the connected DVD player and monitor must be equipped
for a copyright protection system called “HDCP” (High-
bandwidth Digital Content Protection).
HDCP is a copy protection technology consisting of data
encoding and mutual identification of the devices.
The AVR-4308 is HDCP-compatible. For details on the
DVD player or monitor you are using, refer to its operating
instructions.
• When the AVR-4308 and DVD player are connected using an HDMI cable, also connect the AVR-4308 and
monitor using an HDMI cable.
• If the connected monitor or DVD player only has a DVI-D connector, use an HDMI/DVI converter cable.
When using a DVI cable, no audio signals are transmitted.
• Use a Deep Color compatible cable for connection to Deep Color compatible devices.
When connecting with an HDMI/DVI converter cable (adapter)
• HDMI video signals are theoretically compatible with the DVI format.
When connecting to a monitor, etc., equipped with a DVI-D connector, connection is possible using an
HDMI/DVI converter cable, but depending on the combination of components in some cases the video
signals will not be output.
• When connecting using an HDMI/DVI converter adapter, the video signals may not be output properly
due to poor connections with the connected cable, etc.
• By default, the HDMI audio signals are output from the speakers connected to the AVR-4308.
• To output the sound from the TV, make the settings at GUI menu “Manual Setup” – “HDMI Setup”
– “Audio” – “TV” (vpage 31).
NOTE
• Use a CPPM-compatible DVD player to play DVD-Audio discs that are copyright-protected by CPPM.
• The AVR-4308 cannot be controlled from another device via the HDMI cable.
• The audio signals output from the HDMI connector (sampling frequency, bit rate, etc.) may be restricted
by the connected device.
• Video signals are not output properly when using devices that are not HDCP-compatible.
• Video signals are not output if the input video signals do not match the monitor’s resolution. In this case,
switch the DVD player’s resolution to a resolution with which the monitor is compatible.
• If the GUI menu “Manual Setup” – “HDMI Setup” – “Audio” setting (vpage 31) is set to “Amp”, the
sound may be interrupted when the monitor’s power is turned off.
• Use a cable on which the HDMI logo is indicated (a certified HDMI product) for connection to the HDMI
connector. Normal playback may not be possible when using a cable other than one on which the HDMI
logo is indicated (a non-HDMI-certified product).
• If the monitor or DVD player does not support deep color, deep color signal transfer is not possible.
• If the monitor or DVD player does not support xvYCC, xvYCC signal transfer is not possible.
• If the monitor does not support “Auto Lipsync Correction” function, this function will not work.
Connecting Equipment with HDMI connectors
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
• Connect the cables to be used (vpage 9 “Video Conversion Function”).
• With HDMI connections, the video and audio signals can be transferred with a single cable.
• To output the audio signals to the monitor with HDMI connections, set GUI menu “Manual Setup”
– “HDMI Setup” – “Audio” to “TV” (vpage 31).
Connecting the Monitor
47*%&0
*/
7*%&0
$0.10/&/57*%&0
: 1#13
7*%&0
*/
)%.*
*/ */
47*%&0
065
"6%*07*%&0
$0.10/&/57*%&0
: 1#13
7*%&0
065 065
"6%*0 $0"9*"-
065
3-
065065
)%.*
R
L
R
L
Monitor
Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect
correctly.
Connecting the Playback Components
DVD Player
• Connect the cables to be used.
• With HDMI connections, the video and audio signals can be transferred with a single cable.
DVD player
NOTE
• The component video connectors may be indicated differently on your monitor. For details, see the
monitor’s operating instructions.
• The audio signals output from the HDMI connectors are only the HDMI input signals.
Video-converted HDMI signals are not included in the audio signals. To play the sound by monitor, make
analog or digital audio output connections to monitor’s audio input connectors. • Connect an HDP (High-Definition Player) in the same way.
• When using an optical cable for the digital audio connection, make the settings at GUI menu “Source
Select” – “DVD” – “Assign” – “Digital” (vpage 41).
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
Record Player
• When connecting a record player with an MC cartridge, use a
commercially available MC head amplifier or a step-up transformer.
• Induction humming (a booming sound) may be produced from the
speakers if the volume is raised with no record player connected.
• With some record players, noise may be generated when the ground
wire is connected. If so, disconnect the ground wire.
(/%
"6%*0
065
R
L
Turntable (MM cartridge)
NOTE
The AVR-4308’s SIGNAL GND terminal is meant to reduce noise when
a record player is connected. This is not a safety ground terminal.
"6%*0
"6%*0 $0"9*"-
065
3-
065
R
L
R
L
CD Player
Connect the cables to be used.
CD player
iPod®
Example :
"4%3
RL
RL
iPod
When using an optical cable for the digital audio connection, make the
settings at GUI menu “Source Select” – “CD” – “Assign” – “Digital”
(vpage 41).
• With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
• To assign the iPod to a connector other than VCR (iPod), make the
settings at GUI menu “Source Select” – “(input source to which iPod
dock assigned)” – “Assign” – “iPod dock” (vpage 42).
Use a DENON Control Dock for iPod (ASD-1R, sold separately) to
connect the iPod to the AVR-4308. For instructions on the Control
Dock for iPod settings, refer to the Control Dock for iPod’s operating
instructions.
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
47*%&0
065
"6%*07*%&0
$0.10/&/57*%&0
: 1#13
7*%&0
065 065
"6%*0
3-
065
$0"9*"-
065
R
L
R
L
TV/CABLE Tuner
Connect the cables to be used.
TV tuner
When using an optical cable for the digital audio connection, make the settings at GUI menu “Source
Select” – “TV/CBL” – “Assign” – “Digital” (vpage 41).
Satellite Receiver
Connect the cables to be used.
47*%&0
065
"6%*07*%&0
7*%&0
065 065
015*$"-"6%*0
3-
065
R
L
R
L
DBS / BS tuner
• When using a coaxial digital cable for the digital audio connection, make the settings at GUI menu “Source
Select” – “SAT” – “Assign” – “Digital” (vpage 41).
• When using a component video cable for the video connection, make the settings at GUI menu “Source
Select” – “SAT” – “Assign” – “Component” (vpage 42).
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect
correctly.
Connecting the Recording Components
Digital Video Recorder
Connect the cables to be used.
47*%&0
*/
3- 3-
*/*/065
"6%*07*%&0
*/065
015*$"-
065
"6%*07*%&0
065
R
L
R
L
R
L
R
L
Digital video recorder
NOTE
Do not connect the output of the component connected to the AVR-4308’s OPTICAL2 output connector to
any input connector other than OPTICAL2.
• Make analog connections if you wish to record analog audio signals.
• When recording via the AVR-4308, the playback device’s cable must be of the same type as the cable
used to connect the AVR-4308’s DVR OUT connector.
Example: TV IN →S-Video cable : DVR OUT →S-Video cable
TV IN →Video cable : DVR OUT →Video cable
• When using a component video cable for the video connection, make the settings at GUI menu “Source
Select” – “DVR” – “Assign” – “Component” (vpage 42).
or or
47*%&0
*/
3- 3-
*/*/065
"6%*07*%&0
065
"6%*07*%&0
065 */065
015*$"-
R
L
R
L
R
L
R
L
Video Cassette Recorder
Connect the cables to be used.
Video cassette recorder
• When recording via the AVR-4308, the playback device’s cable must be of the same type as the cable
used to connect the AVR-4308’s VCR OUT connector.
Example: TV IN →S-Video cable : VCR OUT →S-Video cable
TV IN →Video cable : VCR OUT →Video cable
• When using a component video cable for the video connection, make the settings at GUI menu “Source
Select” – “VCR” – “Assign” – “Component” (vpage 42).
or
NOTE
Do not connect the output of the component connected to the AVR-4308’s OPTICAL3 output connector to
any input connector other than OPTICAL3.
or
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
3- 3-
065 */065
015*$"-
*/
"6%*0
"6%*0
R
L
R
L
R
L
R
L
CD Recorder / MD Recorder / Tape Deck
Make analog connections if you wish to record analog audio signals, or digital connections if you wish to
record digital audio signals, depending on the types of connectors on the components being used.
CD recorder /
MD recorder / Tape deck
NOTE
Do not connect the output of the component connected to the AVR-4308’s OPTICAL3 output connector to
any input connector other than OPTICAL3.
or
Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect
correctly.
Connections to Other Devices
%&/0/-*/,
7*%&0
Components Equipped with a DENON LINK connector
Multi-channel playback is possible with DVD-Audio discs, Super Audio CD, etc.
DVD player
To use with DENON LINK connections, make the settings at GUI menu “Source Select” – “Assign” –
“Digital” – “DENON LINK” (vpage 41).
Connections


Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting
47*%&0
065
"6%*07*%&0
7*%&0
065 065
015*$"-"6%*0
3-
065
R
L
R
L
46#
800'&3
$&/5&3 463306/%
#"$,
3-
463306/%
3-
'30/5
3-
"6%*0
R
L
R
L
R
L
R
L
R
L
R
L
Video Camera / Game Console
Video camera / Game console
Component with Multi-channel Output
connectors
DVD player /
Super Audio CD player / External decoder
• To play the analog input signals input to the EXT. IN connectors,
press the INPUT MODE button on the main unit or INPUT button
on the main remote control unit and select “EXT. IN” or make the
settings at GUI menu “Source Select” – “(input source)” – “Input
Mode” – “Input Mode” – “EXT. IN” (vpage 40).
• The video signal can be connected in the same way as a DVD player
(vpage 13).
• To play copyright-protected discs, connect the AVR-4308’s EXT.
IN connector with the DVD player’s analog multi-channel output
connector.
46#
800'&3
$&/5&3 463306/%
#"$,
3-
463306/%
3-
'30/5
3-
"6%*0
R
L
R
L
R
L
R
L
R
L
R
L
External Power Amplifier
When using just one surround back speaker, connect it to the left
channel (SBL).
Power amplifier
Connections