Denon AVR-X6200W User manual

MODEL JP E3 E2 EK EA E1 E1C E1K
AVR-X6200W
P P P
INTEGRATED NETWORK AV RECEIVER
Ver. 1
• Please use this service manual with referring to the operating instructions without fail.
• Some illustrations using in this service manual are slightly different from the actual set.
• For purposes of improvement, specications and design are subject to change without notice.
e
SERVICE MANUAL
e
D&M Holdings Inc.

ABOUT THIS MANUAL................................................................3
What you can do with this manual ...........................................3
Using Adobe Reader (Windows version)...................................4
SAFETY PRECAUTIONS...............................................................6
NOTE FOR SCHEMATIC DIAGRAM..............................................7
NOTE FOR PARTS LIST................................................................7
Instructions for handling semi-conductors and optical unit ...7
1. Ground for Human Body......................................................7
2. Ground for Workbench ........................................................7
TECHNICAL SPECIFICATIONS.....................................................9
DIMENSION ..............................................................................10
CAUTION IN SERVICING ...........................................................11
Initializing This Unit.................................................................11
JIG FOR SERVICING ..................................................................11
DISASSEMBLY ..........................................................................12
1. FRONT PANEL ASSY............................................................14
2. RADIATOR ASSY .................................................................15
3. SMPS ASSY .........................................................................16
4. POWER TRANS....................................................................17
5. BACK PANEL ASSY..............................................................18
SPECIAL MODE.........................................................................19
Special mode setting button ..................................................19
1. Version Display Mode ........................................................20
2. Selecting the Mode for Service-related Operations...........24
PROTECTION DIAGRAM......................................................25
DIAGNOSTIC PATH DIAGRAM ............................................30
3. PANEL / REMOTE LOCK Selection Mode ............................74
4. Protection Pass Mode ........................................................75
5. CY920 Reboot Mode ..........................................................75
6. CY920 Initialization Mode ..................................................76
JIG FOR SERVICING ..................................................................77
Procedure after Replacing the Printed circuit boards............79
Procedure after Replacing the Microprocessor, etc...............79
FIRMWARE UPDATE PROCEDURE............................................80
1. Updating via USB ...............................................................80
2. Updating via DPMS ............................................................89
ADJUSTMENT...........................................................................96
SURROUND MODES AND PARAMETERS..................................97
TROUBLE SHOOTING..............................................................100
1. POWER .............................................................................100
2. Analog video....................................................................101
3. HDMI/DVI .........................................................................103
4. AUDIO ..............................................................................105
5. Network/Bluetooth/USB ..................................................108
6. SMPS ................................................................................113
Audio Check PASS .................................................................115
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK...................116
LEVEL DIAGRAM.....................................................................117
BLOCK DIAGRAM ...................................................................125
A.AUDIO / Z2,3HPF DIAGRAM ...............................................125
DIGITAL AUDIO / NETWORK DIAGRAM .................................126
VIDEO DIAGRAM ...................................................................127
POWER DIAGRAM..................................................................128
CPU DIAGRAM.......................................................................129
PRINTED CIRCUIT BOARDS ....................................................130
SCHEMATIC DIAGRAMS (01/33).............................................135
SCH01_DIGITAL CONNECT....................................................135
SCH02_DIR ADC ZONEDAC...................................................136
SCH03_AUDIO PLD ...............................................................137
SCH04_DSP1 .........................................................................138
SCH05_DSP2 .........................................................................139
SCH06_DSP3 .........................................................................140
SCH07_DSP4 .........................................................................141
SCH08_MAIN CPU.................................................................142
SCH09_SUB CPU....................................................................143
SCH10_DECODER..................................................................144
SCH11_HDMI SW1 ................................................................145
SCH12_HDMI SW2 ................................................................146
SCH13_IP SCALER..................................................................147
SCH14_IP SCALER DDR .........................................................148
SCH15_VIDEO PLD ................................................................149
SCH16_HDMI RX TX ..............................................................150
SCH17_HDMI SUPPLY ...........................................................151
SCH18_NETWOR ...................................................................152
SCH19_AUDIO VIDEO CONNECT...........................................153
SCH20_AUDIO VOLUME........................................................154
SCH21_PREOUT.....................................................................155
SCH22_VIDEO SELECTOR ......................................................156
SCH23_CONNECT..................................................................157
SCH24_ZONEDAC ADC .........................................................158
SCH25_MAIN DAC.................................................................159
SCH26_FRONT HDMI USB .....................................................160
SCH27_SPEAKER ...................................................................161
SCH28_REG ...........................................................................162
SCH29_FRONT.......................................................................163
SCH30_SMPS.........................................................................164
SCH31_AMP CONNECT .........................................................165
SCH32_232C PHONO ............................................................166
SCH33_POWER AMP .............................................................167
EXPLODED VIEW ....................................................................168
PACKING VIEW .......................................................................169
SEMICONDUCTORS ................................................................170
1. IC's....................................................................................170
2. FL DISPLAY ......................................................................192
CONTENTS
2

Jump to the target of a schematic diagram
connector
Click the Ref. No. of the target connector in the red
box around a schematic diagram connector.
•The screen jumps to the target connector.
• Page magnication stays the same as before the
jump.
CP401
CP106
v
ABOUT THIS MANUAL
Read the following information before using the service manual.
What you can do with this manual
Search for a Ref. No. (phrase)
(Ctrl+Shift+F)
You can use the search function in Acrobat Reader to
search for a Ref. No. in schematic diagrams, printed
wiring circuit diagrams, block diagrams, and parts
lists.
1. Press Ctrl+Shift+F on the keyboard.
• The Search window appears.
2. Enter the Ref. No. you want to search for in the
Search window, and then click the Search button.
• A list of search results appears.
3. Click an item on the list.
• The screen jumps to the page for that item, and the
search phrase is displayed.
Ctrl
Shift
F
3

Using Adobe Reader (Windows version)
• Properties
Click this button and check that the printer is set to a
suitable paper size.
• Page to print
Select the following checkbox.
"More Options" : "Current View"
• Page Sizing & Handling
Select the following checkbox.
"Size" / "Size Options" : "Fit"
Add notes to this data (Sign)
The Sign function lets you add notes to the data in
this manual.
Save the le once you have nished adding notes.
[Example using Adobe Reader X]
On the "View" menu, click "Sign".
• The Sign pane appears.
[Example using Adobe Reader 9]
On the "Document" menu, click "Sign".
Magnify schematic / printed circuit board
diagrams - 1
(Ctrl+Space, mouse operation)
Press Ctrl+Space on the keyboard and drag the
mouse to select the area you want to view.
• The selected area is magnied.
• When you want to move the area shown, hold
down Space and drag the mouse.
• When you want to show a full page view, press
Ctrl+0 on the keyboard.
Ctrl Space
0
Print a magnied part of the manual
The Properties dialog box and functions will vary depending on your printer.
1. Drag the mouse to magnify the part you want to print.
2. On the "File" menu, click "Print".
3. Congure the following settings in the Print dialog box.
4. Click the Print button to start printing.
4

Magnify schematic / printed circuit board
diagrams - 2
(Pan & Zoom function)
The Pan & Zoom function lets you see which part of
a magnied diagram is being shown in a separate
window.
[Example using Adobe Reader X]
On the "View" menu, point to "Zoom", and then
click "Pan & Zoom".
• The Pan & Zoom window appears on the screen.
[Example using Adobe Reader 9]
On the "Tools" menu, point to "Select & Zoom",
and then click "Pan & Zoom Window".
Magnify schematic / printed circuit board
diagrams - 3
(Loupe Tool function)
The Loupe Tool function lets you magnify a specic
part of a diagram in a separate window.
[Example using Adobe Reader X]
On the "View" menu, point to "Zoom", and then
click "Loupe Tool".
• The Loupe Tool window appears on the screen.
[Example using Adobe Reader 9]
On the "Tools" menu, point to "Select & Zoom",
and then click "Loupe Tool Window".
5

SAFETY PRECAUTIONS
The following items should be checked for continued protection of the customer and the service technician.
leakage current check
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the set is defective.
Be sure to test for leakage current with the AC plug in both polarities, in addition, when the set's power is in each state
(on, off and standby mode), if applicable.
CAUTION Please heed the following cautions and instructions during servicing and
inspection.
◎Heed the cautions!
Cautions which are delicate in particular for servicing are
labeled on the cabinets, the parts and the chassis, etc. Be
sure to heed these cautions and the cautions described in
the handling instructions.
◎Cautions concerning electric shock!
(1) An AC voltage is impressed on this set, so if you touch
internal metal parts when the set is energized, you
may get an electric shock. Avoid getting an electric
shock, by using an isolating transformer and wearing
gloves when servicing while the set is energized, or
by unplugging the power cord when replacing parts,
for example.
(2) There are high voltage parts inside. Handle with extra
care when the set is energized.
◎ Caution concerning disassembly and assembly!
Through great care is taken when parts were
manufactured from sheet metal, there may be burrs on
the edges of parts. The burrs could cause injury if ngers
are moved across them in some rare cases. Wear gloves
to protect your hands.
◎Use only designated parts!
The set's parts have specic safety properties (re
resistance, voltage resistance, etc.). Be sure to use parts
which have the same properties for replacement. The
burrs have the same properties. In particular, for the
important safety parts that are indicated by the z mark
on schematic diagrams and parts lists, be sure to use the
designated parts.
◎ Be sure to mount parts and arrange the wires
as they were originally placed!
For safety seasons, some parts use tapes, tubes or other
insulating materials, and some parts are mounted away
from the surface of printed circuit boards. Care is also
taken with the positions of the wires by arranging them
and using clamps to keep them away from heating and
high voltage parts, so be sure to set everything back as it
was originally placed.
◎Make a safety check after servicing!
Check that all screws, parts and wires removed or
disconnected when servicing have been put back in
their original positions, check that no serviced parts have
deteriorate the area around. Then make an insulation
check on the external metal connectors and between the
blades of the power plug, and otherwise check that safety
is ensured.
(Insulation check procedure)
Unplug the power cord from the power outlet, disconnect
the antenna, plugs, etc., and on the power. Using a 500V
insulation resistance tester, check that the insulation
resistance value between the inplug and the externally
exposed metal parts (antenna terminal, headphones
terminal, input terminal, etc.) is 1MΩ or greater. If it is
less, the set must be inspected and repaired.
Many of the electric and the structural parts used in the
set have special safety properties. In most cases these
properties are difcult to distinguish by sight, and the use
of replacement parts with higher ratings (rated power
and withstand voltage) does not necessarily guarantee
that safety performance will be preserved. Parts with
safety properties are indicated as shown below on the
wiring diagrams and the parts list in this service manual.
Be sure to replace them with the parts which have the
designated part number.
(1) Schematic diagrams Indicated by the z mark.
(2) Parts lists Indicated by the z mark.
The use of parts other than the designated parts could
cause electric shocks, res or other dangerous situations.
CAUTION Concerning important safety
parts
6

NOTE FOR SCHEMATIC DIAGRAM
WARNING:
Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
CAUTION:
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If
the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set
is defective.
WARNING:
DO NOT return the set to the customer unless the problem is identied and remedied.
NOTICE:
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM
ALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICRO FARAD. EACH
VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT
PRIOR NOTICE.
NOTE FOR PARTS LIST
1. Parts indicated by "nsp" on this table cannot be supplied.
2. When ordering a part, make a clear distinction between "1" and "I" (i) to avoid mis-supplying.
3. A part ordered without specifying its part number can not be supplied.
4. Part indicated by " ★" mark is not illustrated in the exploded view.
WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT
Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged
on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface,
where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the
body grounding band, be careful to avoid contacting semi-conductors with your clothing
<Incorrect>
CBA
Grounding Band
Conductive Sheet or
Copper Plate
1MΩ
1MΩ
<Correct>
CBA
7

Personal notes:
8

TECHNICAL SPECIFICATIONS
nAudio section
• Power amplier
Rated output :
Front：
140W+140W (8Ω, 20Hz - 20kHz with 0.05% T.H.D.)
175W+175W (6Ω, 1kHz with 0.7% T.H.D)
Center :
140W (8Ω, 20Hz - 20kHz with 0.05% T.H.D.)
175W (6Ω, 1 kHz with 0.7 % T.H.D.)
Surround :
140W+140W (8Ω, 20 Hz - 20 kHz with 0.05% T.H.D.)
175W+175W (6Ω, 1 kHz with 0.7 % T.H.D.)
Surround back / Height1 / Front wide / Height2:
140W+140W (8Ω, 20 Hz - 20 kHz with 0.05% T.H.D.)
175W+175W (6Ω, 1 kHz with 0.7 % T.H.D.)
Rated output :
160 W x 2-channel (8 Ω)
250 W x 2-channel (4 Ω)
Output connectors : 4 - 16 Ω
nAnalog section
Input sensitivity/Input impedance : 200 mV / 47 kΩ
Frequency response : 10 Hz - 100 kHz — +1, -3 dB(Direct mode)
S/N : 102 dB(IHF-A weighted, Direct mode)
Distortion : 0.005 % (20 Hz – 20 kHz) (Direct mode)
Rated output : 1.2 V
nDigital section
D/A output : Rated output — 2 V (at 0 dB playback)
Total harmonic distortion — 0.008 % (1 kHz, at 0 dB)
S/N ratio — 102 dB
Dynamic range — 100 dB
Digital input : Format — Digital audio interface
nPhono equalizer section
Input sensitivity : 2.5 mV
RIAA deviation : ±1 dB (20 Hz to 20 kHz)
S/N : 74 dB (IHF-A)
Distortion factor : 0.03 % (1 kHz, 3 V)
nVideo section
• Standard video connectors
Input/output level and impedance : 1 Vp-p, 75 Ω
Frequency response : 5 Hz - 10 MHz — 0, -3 dB
• Color component video connector
Input/output level and impedance : Y signal — 1 Vp-p, 75 Ω
PB / CB signal — 0.7 Vp-p, 75 Ω
PR / CR signal — 0.7 Vp-p, 75 Ω
Frequency response : 5 Hz - 60 MHz — 0, -3 dB
nTuner section
Reception frequency range : FM 87.5 MHz - 107.9 MHz(for E3)
FM 87.5 MHz - 108.0 MHz(for E2, E1C)
AM 530 kHz - 1710 kHz(for E3)
AM 522 kHz - 1611 kHz(for E2, E1C)
Effective sensitivity : FM 1.5μV(14.8dBf)
AM 20 μV
50 dB sensitivity : MONO ― 2.8 μV (20.2 dBf)
S/N ratio (IHF-A) : MONO ― 78 dB
STEREO ― 68 dB
HD ― FM 85dB AM 85dB
Distortion (1 kHz) : MONO ― 0.1 %
SRETEO ― 0.2 %
HD ― FM 0.02% AM 0.02%
nWireless LAN section
Network type
(wireless LAN standard) : onforming to Wi-Fi®z1
Security : WEP 64 bit, WEP 128 bit
WPA/WPA2-PSK (AES)
WPA/WPA2-PSK (TKIP)
Radio frequency : 2.4 GHz
No. of channels : 1 - 11 ch (for E3)
1 - 13 ch (for E2, E1C)
z1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product
Logo are registered trademarks of the Wi-Fi Alliance.
nBluetooth section
Communications system : Bluetooth Version 2.1 + EDR
(Enhanced Data Rate)
Transmission power : Maximum 2.5 mW (Class 2)
Maximum communication range : Approx. 32.8 ft/10 m in line of sight
Frequency band : 2.4 GHz band
Modulation scheme : FHSS (Frequency-Hopping Spread Spectrum)
Supported proles : A2DP 1.2 (Advanced Audio Distribution Prole)
AVRCP 1.4 (Audio Video Remote Control Prole)
Corresponding codec : SBC, AAC
Transmission range (A2DP) : 20 Hz - 20,000 Hz
nGeneral
Power supply : (for E3) : AC 120 V, 60 Hz
(for E2) : AC 230 V, 50 Hz / 60 Hz
(for E1C) : AC 220 V, 50 Hz
Power consumption : 730W
Power consumption in standby mode : 0.1 W
Power consumption in CEC standby mode : 0.5 W
Power consumption in network standby mode : 4.5W
For purposes of improvement, specications and design are subject to
change without notice.
9

17 1/8 (434)
9 3/8 (237)
15 1/8 (383)
2 1/4
(55)
2 7/8
(70)
5/8
(15) 6 (152)
6 5/8 (167)
9 3/8 (235)
13 3/8 (339) 15 1/2 (393)
7/8
(22)
1/2
(12)
1 3/8
(32)
13 5/8 (344)
2 3/8
(60)
1 7/8 (45)1 7/8 (45)
DIMENSION
Unit : in. (mm)
Weight : 31 lb 1 oz (14.1 kg)
10

CAUTION IN SERVICING
Initializing This Unit
Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB.
1. Press the power button to turn off the power.
2. While holding down buttons "CURSOR d" and "CURSOR f" simultaneously, press the power button to turn on the
power.
3. Release the buttons after conrming that the display ashes at 1-second intervals.
＊ The unit is initialized.
NOTE：• If the unit fails to enter the service mode in step 3, repeat the procedure from step 1.
• Initializing the device restores the customized settings to the factory settings. Write down your settings in advance and
recongure the settings after initialization.
JIG FOR SERVICING
Use the following jigs (extension cable kit) when repairing the PCBs.
Order with your dealer for the jigs your dealer if necessary.
8U-110084S : EXTENSION UNIT KIT : 2Sets
(See page 77)
XCURSOR dCURSOR f
11

DISASSEMBLY
• Remove each part following the ow below.
• Reassemble the removed parts in the reverse order.
• Read "Precautions During Work" before reassembling the removed parts.
• If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completingthe
work. Failure to shape the wires correctly may cause problems such as noise.
FRONT PANEL ASSY
See "DISASSEMBLY"
1. FRONT PANEL ASSY
and "EXPLODED VIEW"
FLD PCB
(Ref. No. of EXPLODED VIEW : C1)
HP PCB
(Ref. No. of EXPLODED VIEW : C2)
HDMI USB FRONT PCB
(Ref. No. of EXPLODED VIEW : B2)
TOP COVER
MAIN TRANS
See "DISASSEMBLY"
4. MAIN TRANS
and "EXPLODED VIEW"
POWER TRANS
(Ref. No. of EXPLODED VIEW : 8)
RADIATOR ASSY
See "DISASSEMBLY"
2. RADIATOR ASSY
and "EXPLODED VIEW"
AMP PCB
(Ref. No. of EXPLODED VIEW : D)
R-AMP CONNECT PCB
(Ref. No. of EXPLODED VIEW : D1)
L-AMP CONNECT PCB
(Ref. No. of EXPLODED VIEW : D2)
RADI_PROTDET2 PCB
(Ref. No. of EXPLODED VIEW : D5)
BACK PANEL ASSY
See "DISASSEMBLY"
5. BACK PANEL ASSY
and "EXPLODED VIEW"
DIGITAL PCB
(Ref. No. of EXPLODED VIEW : A)
AUDIO/VIDEO PCB
(Ref. No. of EXPLODED VIEW : B)
DAC PCB
(Ref. No. of EXPLODED VIEW : B1)
CONNECTOR-1 PCB
(Ref. No. of EXPLODED VIEW : B4)
CONNECTOR-2 PCB
(Ref. No. of EXPLODED VIEW : B5)
CONNECTOR-3 PCB
(Ref. No. of EXPLODED VIEW : B6)
CONNECTOR-5 PCB
(Ref. No. of EXPLODED VIEW : B8)
SPEAKER PCB
(Ref. No. of EXPLODED VIEW : C)
HL SPEAKER PCB
(Ref. No. of EXPLODED VIEW : C3)
232C POHNO PCB
(Ref. No. of EXPLODED VIEW : D4)
SMPS PCB
See "DISASSEMBLY"
3. SMPS PCB
and "EXPLODED VIEW"
SMPS PCB
(Ref. No. of EXPLODED VIEW : D3)
12

Explanatory Photos for DISASSEMBLY
• For the shooting direction of each photos used in this manual, see the photo below.
• A, B, C and D in the photo below indicate the shooting directions of photos.
• The photographs with no shooting direction indicated were taken from the top of the unit.
• Photos of AVR-X6200W E3 are used in this manual.
The viewpoint of each photograph
(Shooting direction : X) [View from the top]
Front side
Shooting
direction: D Shooting direction: C
↑Shooting direction: A↑
↓Shooting direction: B↓
13

1. FRONT PANEL ASSY
Proceeding : TOP COVER →FRONT PANEL ASSY
(1) Remove the screws.
(2) Remove the screws. Remove the STYLE PIN, HOLDER, FFC and connector wire.
View from the bottom
N6401
N903
FFC FFC
CUT
HOLDER
14

2. RADIATOR ASSY
Proceeding : TOP COVER →FRONT PANEL ASSY →RADIATOR ASSY
(1) Remove the STYLE PIN and connector wire. Remove the screws.
(2) Remove the connector wire.
N5812 N5842
N5832 N5831
L-AMP CONNECT R-AMP CONNECT
STYLE PIN
L-AMP CONNECT R-AMP CONNECT
FHR
YELLOW
SBR
GRAY
SR
BROWN
FR
RED
FHL
YELLOW
SBL
GRAY
SL
BROWN
C
BLUE
FL
RED
N5824N5814
STYLE PIN N5842
15

3. SMPS ASSY
Proceeding : TOP COVER →FRONT PANEL ASSY →RADIATOR ASSY →SMPS ASSY
(1) Remove the screws.
(2) Cut the wire clamp, then remove the connector wires.
Shooting
direction: C
↑Shooting direction: A↑
N6502
N6501
CUT
CUT
16

4. POWER TRANS
Proceeding : TOP COVER →FRONT PANEL ASSY →RADIATOR ASSY →SMPS ASSY →POWER TRANS
(1) Remove the screws. Remove the HOLDER.
(2) Remove the STYLE PIN and connector wire.
HOLDER
N6201
N6012
N9022
STYLE PIN
STYLE PIN
17

5. BACK PANEL ASSY
Proceeding : TOP COVER →FRONT PANEL ASSY →RADIATOR ASSY →SMPS ASSY →POWER TRANS
→BACK PANEL ASSY
(1) Remove the screws.
Shooting
direction: D Shooting direction: C
↑Shooting direction: A↑
18

SPECIAL MODE
Special mode setting button
b No. 1 - 6, 9 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power.
b No. 7, 8 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds .
b No. 10 : While holding down buttons "A" and "B" simultaneously, insert the AC plug into the wall outlet to turn on the power.
No. Mode Button A Button B Button C Descriptions
1Version Display
(u-COM / DSP Error Display) SETUP OPTION -
Displays the version of rmware such as the main rmware or DSP.
Errors that have occurred are displayed.
(See page 20)
2 Selecting the Mode for Service-related STATUS ZONE3
SOURCE -This is a display for turning on each service-related mode. Service-related modes: No. 2-1 - No. 2-6
2-1 Check the Video/Audio path Mode ↑ - -
This is a special mode for service conrmation used during repair
work to simplify the conrmation work for the Audio channel /
video channel. (See page 26)
2-2 Protection history display mode ↑ - - Displays the protection occurrence history.
(See page 69)
2-3 232C Standby Clear Mode ↑ Switches from 232C standby mode to normal standby mode.
(See page 70)
2-4 Operation Info Mode ↑ - -
Displays the accumulated operating time of the unit, the
number of times the power was switched on, and the number of
occurrences of each protection. (See page 71)
2-5 TUNER STEP Mode
(E3 and E2 model only) ↑ - - Enables reception STEP of the ANALOG TUNER to be changed. (See page 72)
2-6 Remote ID Setup Mode ↑ - -
If there are multiple DENON AV receivers in the same area,
this mode prevents other AV receivers from being operated
concurrently with this device. (See page 73)
3 User Initialization Mode BACK INFO - Initializes backup data.
(Settings for the Installer Setup are not initialized.)
4 Factory Initialization Mode CURSOR dCURSOR f-Initializes backup data.
(The settings for the Installer Setup is also initialized.)
5 PANEL / REMOTE LOCK Selection Mode STATUS INFO -
Start this unit in the PANEL/REMOTE LOCK selection mode so that
PANEL LOCK and Remote Lock can be switched between ON and
OFF. (See page 74)
6 Protection Pass Mode CURSOR
0STATUS ZONE3
SOURCE
Enables the power to be turned on when protection detection is
disabled. (See page 75)
7 CY920 Reboot Mode DIMMER SETUP - The CY920 is restarted after CY920 hang up.
8CY920 Initialization Mode DIMMER CURSOR
1-Enter this mode only after replacing Flash for CY920 and rewriting
the rmware.
9 USB Update mode STATUS OPTION - Switches this unit to USB Update mode.
10 Forced USB All Device Write Mode STATUS OPTION -
Mode used when this unit cannot be recovered.
Forcibly switches this unit to USB update mode.
(See page 82)
NOTE:
When the volume indicator displays " ", the set has entered a special mode for developers.
In this case, RS-232C communication cannot be used.
To cancel this special mode, press and hold the "CURSOR f"and "STATUS" buttons for 3 seconds and longer. When the volume
indicator returns to the normal display, RS-232C communication can be used.
X
ZONE3
SOURCE
d
0 1
STATUS DIMMER
INFO OPTION
SETUPBACK f
19

1. Version Display Mode
1.1. Actions
Version information is displayed when the device is started in this mode.
1.2. Starting up
While holding down buttons "SETUP" and "OPTION" simultaneously, press the power button to turn on the power.
then press the "STATUS" button to display the information in section 1.3 on the display.
b The version list is also displayed on GUI while the version is displayed on the display.
1.3. Display Order
Error information("See "1.4. Error display") → q Model destination information, Serial Number
→ w Firmware Package Version → e Main µ-com, Main 1st Boot Loader Version
→ r Sub μ -com, Sub 1st Boot Loader Version → t DSP1/2/3/4 ROM → y Audio, Video PLD → u GUI SFLASH
→ i Ethernet 1st Boot Loader, Hardware ID → o Ethernet 2nd Boot Loader, Rhapsody Flag → Q0 Ethernet IMAGE
→ Q1 Ethernet MAC ADDRESS information → Q2 BT MAC ADDRESS information → Q3 HD Radio (E3 only)
→ Q4 MultEQ Pro APP (Displayed when Audyssey Pro is complete)
→ Q5 MultEQ Pro ICL (Displayed when Audyssey Pro is complete)
q Model destination information, Serial Number：
FLD L1 AVR-X6200W E3
FLD L1 AVR-X6200W E2
FLD L1 AVR-X6200W E1C
FLD L2 S/N. **********
w Firmware Package Version：
FLD L1 Firm. Package
L2 Ver.:****
e Main µ-com, Main 1st Boot Loader Version:
FLD L1 Main :**.**
L2 Main FBL :**.**
r Sub µ-com, Sub 1st Boot Loader Version:
FLD L1 Sub :7110****
L2 Sub FBL :**.**
t DSP1/2/3/4 ROM :
FLD L1 DSP1 :**.**
L2 DSP2 :**.**
FLD L1 DSP3 :**.**
L2 DSP4 :**.**
y Audio, Video PLD :
FLD L1 Audio PLD:**.**
L2 Video PLD:**.**
20