Denon AVR-4810CI User manual

AV SURROUND RECEIVER
AVR-4810CI
Owner’s Manual
GraphicalUserInterface
Use this manual in combination with the
operating guide displayed on the GUI screen.
GUI Menu Operation (vpage 30)
GUI Menu Map (vpage 29)
Language (vpage 57)
Remote Control Unit Operations (vpage 108)

I
nSAFETY PRECAUTIONS
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPOTANT SAFETY
INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
CAUTION:
• The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
• No naked flame sources, such as lighted candles, should be
placed on the unit.
• Observe and follow local regulations regarding battery disposal.
• Do not expose the unit to dripping or splashing fluids.
• Do not place objects filled with liquids, such as vases, on the
unit.
ATTENTION:
• La ventilation ne doit pas être gênée en recouvrant les ouvertures
de la ventilation avec des objets tels que journaux, rideaux, tissus,
etc.
• Aucune flamme nue, par exemple une bougie, ne doit être placée
sur l’appareil.
• Veillez à respecter les lois en vigueur lorsque vous jetez les piles
usagées.
• L’appareil ne doit pas être exposé à l’eau ou à l’humidité.
• Ne pas poser d’objet contenant du liquide, par exemple un vase,
sur l’appareil.
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
PRECAUTION:
Pour déconnecter complètement ce produit du courant secteur,
débranchez la prise de la prise murale.
La prise secteur est utilisée pour couper complètement
l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder
facilement.

II
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une
étagère.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
• Keep the unit free from moisture, water,
and dust.
• Protéger l’appareil contre l’humidité, l’eau
et la poussière.
• Unplug the power cord when not using the
unit for long periods of time.
• Débrancher le cordon d’alimentation
lorsque l’appareil n’est pas utilisé pendant
de longues périodes.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Do not let foreign objects into the unit.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Do not let insecticides, benzene, and
thinner come in contact with the unit.
• Ne pas mettre en contact des insecticides,
du benzène et un diluant avec l’appareil.
• Never disassemble or modify the unit in
any way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
nNOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
FCC Information (For US customers)
1. COMPLIANCE INFORMATION
Product Name: AV Surround Receiver
Model Number: AVR-4810CI
This product contains FCC ID: PPQ-NM100BB.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
product may not cause harmful interference, and (2) this product must accept any interference received, including
interference that may cause undesired operation.
Denon Electronics (USA), LLC
100 Corporate Drive, Mahwah, NJ 07430-2041
Tel. [phone] (Main)
2. IMPORTANT NOTICE: DO NOT MODIFYTHIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
3. CAUTION
• To comply with FCC RF exposure compliance requirement, separation distance of at least 20 cm must be
maintained between the antenna of this product and all persons.
• This product and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter.
4. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for
help.
IC Information (For Canadian customers)
1. PRODUCT
This product contains 4491A-NM100BB.
This product complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) this product may not cause harmful interference, and (2) this product must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
APPAREIL
Cet appareil contiens 4491A-NM100BB.
Cet appareil est conforme à la norme CNR-210 du Canada. L
’utilisation de ce dispositif est autorisée seulement
aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être
prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
2. CAUTION
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
ATTENTION
Afin de réduire le risque d’interférence aux autres utilisateurs, il faut choisir le type d’antenne et son gain de façon à
ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour l’obtention
d’une communication satisfaisante.


Contentsn
Getting Started·······································································2
Flow of Operations Through Playback········································2
Cautions on Handling ···································································2
Cautions on Installation ·······························································2
Preparations ··················································································3
Accessories ··················································································3
About the Remote Control Unit····················································3
Part Names and Functions ···························································4
Front Panel····················································································4
Display ··························································································5
Rear Panel·····················································································6
Remote Control Unit·····································································7
Connections ·············································································9
Important Information··································································9
Cables Used for Connections ·······················································9
Converting Input Video Signals for Output
(Video Conversion Function) ······················································· 10
Installing the Speakers ·······························································11
Speaker Connections··································································14
Connecting Devices ····································································17
Connecting the Power Cord·······················································28
Once Connections are Completed·············································28
Turning the Power On ·································································28
Turning the Power Off·································································28
Settings····················································································29
GUI Menu Map ············································································29
GUI Menu Operation···································································30
Example of the Display of the GUI Mark at a Title ······················30
Examples of GUI Menu Screen Displays····································30
Selecting the Input Source ·························································31
Make the Optimal Speaker Settings, and Correct the Room
Acoustics (Audyssey™ Auto Setup)··········································32
Making Detailed Settings (Manual Setup)································39
Making the Input Settings (Source Select)·······························57
Playback···················································································66
Important Information································································66
Playing Components···································································66
Playing a Blu-ray Disc Player/DVD Player ····································66
Playing an iPod®Using a Control Dock for iPod ·························66
Playing an iPod®Connected Directly to the AVR-4810CI’s
USB Port ·····················································································68
Tuning in Radio Stations····························································69
Listening to FM/AM Broadcasts·················································70
Listening to XM Satellite Radio···················································71
Listening to SIRIUS Satellite Radio·············································73
Listening to HD Radio Technology ··············································75
Playing Network Audio, USB Memory Devices ·······················76
Listening to Internet Radio ·························································78
Playing Files Stored on a Computer············································80
Playing Files Stored on USB Memory Devices···························81
Listening to Napster ···································································82
Listening to Rhapsody ································································83
Operations During Playback ······················································85
Adjusting the Master Volume······················································85
Turning Off the Sound Temporarily (Muting) ·······························85
Listening with Headphones························································85
To Stop························································································85
Stopping Playback Temporarily····················································85
Fast-forwarding or Fast-reversing ···············································85
To Cue to the Beginning of a Track··············································85
Playing Repeatedly ·····································································86
Selecting Tracks···········································································86
Shuffling Playback·······································································86
Playing in Random Order····························································86
Searching Pages ·········································································86
Searching by First Letter ·····························································86
Selecting the Surround Mode (Surround Mode) ·····················87
Adjusting the Sound and Picture Quality
(Audio/Video Adjust)··································································90
Adjusting the Sound (Audio Adjust) ············································90
Adjusting the Picture Quality (Picture Adjust) ·····························95
Checking the Status (Information) ·····························96
Other Operations and Convenient Functions········97
Other Operations ········································································97
Playing a Blu-ray Disc Player Compatible with
DENON LINK 4th········································································97
Playing Super Audio CD ······························································ 98
Recording on an External Device (REC OUT mode)····················98
Convenient Functions·································································99
HDMI Control Function·······························································99
Setting the Power to Standby After a Certain Amount of Time
(Sleep Timer Function) ······························································ 100
Adjust the Volume of the Speakers··········································· 100
Saving Frequently Used Settings (Quick Select Function) ········ 101
Playing the Same Network Audio on Different Devices
Connected in a Network (Party Mode Function)······················· 101
Operating a Wireless LAN-Compatible Mobile Terminal to
Play Music and Still Pictures····················································· 102
Operating the AVR-4810CI with a Browser
(Web Control Function) ····························································· 103
Various Memory Functions······················································· 104
Playing in ZONE2/ZONE3/ZONE4 (Multi-zone
Function)················································································105
Audio Output·············································································105
Video Output ·············································································105
Playback ·····················································································106
Menu Operation ········································································107
Quick Select Function·······························································107
Sleep Timer Function································································107


Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsGetting Started
Perform the operations leading to playback on the AVR-4810CI in the
order shown below.
Audyssey™ Auto Setup (vpage 32)
Connections
Installing/Setting the Speakers (vpage 11)
Speaker Connections (vpage 14)
Connecting Devices (vpage 17)
Turning the Power On (vpage 28)
Settings
Manual Setup (vpage 39)
Perform “Manual Setup” as necessary.b
Source Select (vpage 57)
Playback
Playing Components (vpage 66)
Selecting the Surround Mode (vpage 87)
Adjusting the Sound and Picture Quality
(vpage 90)
Flow of Operations Through
Playback
Cautions on Handling
• Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
• Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
• About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
• Moving the unit
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units before
moving the unit.
• Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
Cautions on Installation
Note:
For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
b
bNote
b b
Getting Started
List of preset codes ··································End of this manual
Wall
Operating the Connected Devices by Remote
Control Unit··········································································108
Operating the Main Remote Control Unit ······························108
Operating AV Equipment ·························································· 108
Presetting·················································································· 109
Operating Preset Components················································· 109
Setting the Remote ID······························································ 112
Learning Function ····································································· 113
MACRO Function ······································································ 114
Punch Through Function···························································· 114
Setting the Time the Backlight Stays Lit ··································· 115
Adjusting the Backlight’s Brightness········································· 115
Specifying the Zone Used with the Main Remote Control Unit
·································································································· 115
Resetting the Main Remote Control Unit ································· 116
Operating the Sub Remote Control Unit ································117
Switching Zones ······································································· 119
Switching the Multi-zone Input Source to the Same
Input Source as Used in the MAIN ZONE ································ 119
Setting the Zone for Which the Sub Remote Control Unit is
Used (ZONE SELECT LOCK Mode)·········································· 119
Setting the Remote ID······························································ 119
Resetting the Settings ······························································ 119
Other Information ·····························································120
Troubleshooting·································································130
Restoring All the Settings to as They were at the Time of
Purchase (Resetting the Microprocessor)·······························134
Specifications······································································135
Getting Started


Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsGetting Started
In addition to the AVR-4810CI, the included main remote control unit
(RC-1126) can also be used to operate the equipment listed below.
q DENON system components
w Non-DENON system components
To operate component products other than DENON, you must set
the preset code (vpage 109 “Presetting”).
If you are using a non-DENON AV device, or if you cannot operate
the device even after registering the preset code, memorize the
other device’s remote control signal in the AVR-4810CI remote
control unit (vpage 113 “Learning Function”).
•
•
LR6/AA
R03/AAA
(RC-1126) (RC-1121)
wLoad the two batteries properly as indicated by the marks in the
battery compartment.
(RC-1126) (RC-1121)
ePut the rear cover back on.
About the Remote Control Unit
Inserting the Batteries
qLift the clasp and remove the rear lid.
NOTE
Insert the specified batteries in the remote control unit.
Replace the batteries with new ones if the set does not operate
even when the remote control unit is operated close to the unit. (The
supplied batteries are only for verifying operation.)
When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
To prevent damage or leakage of battery fluid:
Do not use a new battery together with an old one.
Do not use two different types of batteries.
Do not attempt to charge dry batteries.
Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
Remove the batteries from the remote control unit if it will not be in
use for long periods.
Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
•
•
•
•
•
•
•
•
•
•
•
30°
30°
Approx. 23 feet / 7 m
or
(RC-1126)
(RC-1121)
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
Preparations
t y i
Q5
Q2
Q0
Q4
Q1
Q3
qOwner’s manual ...................................................................... 1
wGetting started ........................................................................ 1
eWarranty (for North America model only)................................ 1
rService station list ................................................................... 1
tPower cord (Cord length: Approx. 6.2 ft / 1.9 m) .................... 1
yMain remote control unit (RC-1126)......................................... 1
uLR6/AA batteries (for RC-1126)................................................ 2
iSub remote control unit (RC-1121).......................................... 1
oR03/AAA batteries (for RC-1121)............................................. 2
Q0 FM indoor antenna .................................................................. 1
Q1 AM loop antenna (small, for AM broadcasts) .......................... 1
Q2 AM loop antenna (large, for HD Radio broadcasts) ................. 1
Q3 Dipole antenna (for HD Radio broadcasts) .............................. 1
Q4 Rod antenna for wireless LAN connection.............................. 1
Q5 Setup microphone
(DM-A409, Cord length: Approx. 25 ft / 7.6 m) ....................... 1
Accessories
Check that the following parts are supplied with the product.
Thank you for purchasing this DENON product. To ensure proper
operation, please read this owner’s manual carefully before using the
product.
After reading them, be sure to keep them for future reference.
Operating Range of the Remote Control Unit
Point the remote control unit at the remote sensor when operating it.
Getting Started


Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsGetting Started
For buttons not explained here, see the page indicated in parentheses ( ).
Part Names and Functions
t
y
o
Q0
Q1
q
Q5 Q6Q4Q3
Q2
r
ui
we
W5
W6
E0
E5 W8W9 E3
E4 E1 E2
Q7 Q8 Q9 W0 W1 W4W3W2
W7
qPower operation button
(ON/STANDBY) ··········································· (28)
wPower indicator (hON jOFF) ················· (28)
ePower switch ·············································· (28)
rDoor
When you are using buttons and/or terminals
behind the door, press the bottom of the door to
open it. When not using buttons and/or terminals
behind the door, close it. Be careful not to catch
your fingers when closing the door.
tQUICK SELECT buttons ····························(101)
yMASTER VOLUME control knob··············· (85)
uAUDYSSEY
DYNAMIC VOLUME™ indicator················ (92)
iAUDYSSEY DSX™ indicator ····················· (93)
oMaster volume indicator
Q0 Display
Q1 Remote control sensor ································ (3)
Q2 SOURCE SELECT knob ······························ (31)
Q3 SOURCE button·········································· (31)
Q4 TUNING PRESET button················ (70, 72, 75)
Q5 ZONE 2/3/4 / REC SELECT button···· (98, 106)
Q6 VIDEO SELECT button ······························· (60)
GWith the door openH
W7 HDMI IN connector····································· (17)
W8 USB (iPod DIRECT) port ····························· (24)
W9 STATUS button ·········································· (96)
E0 DSX button ················································· (93)
E1 RESTORER button······································ (94)
E2 DIRECT/STEREO button ······················ (88, 89)
E3 PURE DIRECT button ································· (89)
E4 DSP SIMULATION button·························· (88)
E5 STANDARD button····································· (87)
Front Panel
Q7 Headphones jack (PHONES)······················ (85)
Q8 ZONE2 ON/OFF button···························· (106)
Q9 ZONE3 ON/OFF button···························· (106)
W0 ZONE4 ON/OFF button···························· (106)
W1 MENU button·············································· (30)
W2 Cursor buttons (uio p)·························· (30)
W3 ENTER button ············································· (30)
W4 RETURN button ·········································· (30)
W5 V.AUX INPUT connectors·························· (24)
W6 SETUP MIC jack ·········································· (33)
Getting Started


Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsGetting Started
uiQ4
Q8
W0W1 oQ0
Q5 Q1Q2 Q3
Q6Q7Q9 y
wq e r t
qInput signal indicators
wInput signal channel indicators
These light when digital signals are input.
When playing HD Audio sources, the“ ”
indicator lights when an extension channel (a
channel other than the front, center, surround,
surround back or LFE channel) is input. If there
are two or more extension channels, the “ ”
and “ ” indicators light.
eInformation display
The input source name, surround mode, setting
values and other information are displayed here.
rOutput signal channel indicators
tMonitor output indicators
These light according to the HDMI monitor output
setting (vpage 43 “Monitor Out”). When set
to “Auto (Dual)”, the indicators light according to
the connection status.
yQUICK SELECT indicators
uMaster volume indicator
iMUTE indicator
This lights when the mute mode is selected
(vpage 85).
oRESTORER indicator
This lights when the RESTORER mode is
selected (vpage 94).
Q0 PARTY indicators
These indicators light during party mode
(vpage 101 “Playing the Same Network Audio
on Different Devices Connected in a Network
(Party Mode Function)”).
• ORGANIZER
This lights to indicate that party mode has
started as Organizer.
• ATTENDEE
This lights to indicate that party mode has
started as Attendee.
Q1 AUDYSSEY MULTEQ XT indicators
Lighting is as follows, depending on the setting
of “Dynamic EQ” (vpage 92) and “Dynamic
Volume” (vpage 93).
• : When“DynamicEQ” and“Dynamic
Volume” are “ON”.
• : When the “Dynamic EQ” setting is
“ON” and the “Dynamic Volume”
setting is “OFF”.
• : When“DynamicEQ” and“Dynamic
Volume” are “OFF”.
Q2 SLEEP indicator
This lights when the sleep mode is selected
(vpage 100).
Q3 Multi zone indicators
These light when the power for the respective
zone is turned on.
Display
Q4 Advanced AL24 indicator
This lights when Advanced AL24 Processing
(vpage 122) or AL 24 Processing Plus
(vpage 122) is activated.
Q5 Input mode indicators
Q6 D.LINK indicator
This lights when playing using DENON LINK
connections (vpage 98 “Playing Super Audio
CD”).
Q7 HDMI indicator
This lights when playing using HDMI connections.
Q8 Tuner reception mode indicators
These light according to the reception conditions
when the input source is set to “TUNER” or
“HD Radio”.
• STEREO
In the FM mode, these light when receiving analog
stereo broadcasts.
• TUNED
Lights when the broadcast is properly tuned in.
• AUTO
These light when in the auto tuning mode.
Q9 Recording output source indicator
This lights when the REC OUT mode is selected
(vpage 98).
W0 Decoder indicators
These light when the respective decoders are
operating.
W1 HD indicator
This lights during HD Radio reception.
Part Names and Functions
Getting Started


Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsGetting Started
yuio
Q0
Q4Q5Q5
eQ2
Q3
qe
w
Q7
Q8
Q9 Q6
tr
Q1u
W0
W2W3
W2
W1
Part Names and Functions
qRS-232C connector····································· (26)
wREMOTE CONTROL jacks ·························· (26)
eAnalog audio connectors···················(18 ~ 21)
rTRIGGER OUT jacks ··································· (26)
tDOCK CONTROL jack ································· (19)
ySIGNAL GND terminal ······························· (19)
uSpeaker terminals ······························ (14 ~ 16)
iAC inlet························································ (28)
oAC OUTLETS··············································· (28)
Q0 HD Radio antenna terminals ····················· (23)
Q1 WLAN ANTENNA terminal ························ (27)
Q2 ETHERNET connector ································ (26)
Q3 USB (iPod DIRECT) port····························· (24)
Q4 XM connector ············································· (21)
Q5 Digital audio connectors····················(18 ~ 24)
Q6 DENON LINK connector····························· (23)
Q7 COMPONENT VIDEO connectors········ (18, 20)
Q8 HDMI connectors········································ (17)
Q9 VIDEO / S-VIDEO connectors············(18 ~ 21)
W0 SIRIUS connector ······································· (22)
W1 FM/AM antenna terminals ························ (22)
W2 PRE OUT connectors·························· (25, 105)
W3 EXT. IN connectors····································· (25)
Rear Panel
Getting Started


Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsGetting Started
nOperations Possible by Main Remote Control Unit
Operations on the AVR-4810CI
Operations on devices other that the AVR-4810CI
Preset the remote control codes of the devices to be operated (vpage 109).
The function button indicator changes depending on the Device select button you have selected.
•
•
Remote Control Unit
Part Names and Functions
w
r
t
y
u
i
o
e
Q0
Q1
Q2
Q3
Q4
Q7
W0
Q6
Q8
Q9
Q5
q
qSignal transmission indicator ················· (108)
wDevice select buttons······························· (108)
eZone indicators / MACRO indicator········ (108)
rMENU button·············································· (30)
SEARCH button ·········································· (86)
tRESTORER button (RSTR) ························· (94)
yCHANNEL LEVEL button ························· (100)
uChannel buttons (CH)·························(70 ~ 75)
iInput source select buttons······················· (31)
Number buttons ···························(70 ~ 75, 79)
oTV INPUT button ·······································(110)
Q0 Remote control signal transmitter ············· (3)
Q1 QUICK SELECT button ······················(101, 107)
MACRO button···········································(114)
Q2 Function buttons
See“OperationsPossiblebyMain RemoteControl
Unit” (vpage 7, 8) for more information.
Q3 Power operation buttons
(POWER ON / OFF)····························· (28, 106)
Q4 Cursor buttons (uio p)························· (30)
Q5 ENTER button ············································· (30)
Q6 Return button (RTN)··································· (30)
Q7 SOURCE SELECT button ··························· (31)
Q8 Master volume control buttons (VOL) ····· (85)
Q9 Muting button (MUTE) ······························ (85)
W0 RC SETUP button ····································· (109)
Main Remote Control Unit (RC-1126)
Selected Device
select button
Function button
indicator Button name
W1
W2
W3
W4
W5
W6
W7
W8
W9
E3
W1 MULTEQ®XT button (MULTEQ) ··················· (92)
W2 DSX button (SPKR) ········································· (93)
W3 Sleep timer button (SLEEP) ··················(100, 107)
W4 DYNAMIC EQ™ button (DYN EQ)·················· (92)
W5 DYNAMIC VOLUME™ button (DYN VOL) ····· (93)
W6 Surround mode buttons··························· (88, 89)
• STANDARD button (STD)
• PURE DIRECT button (PURE)
• DIRECT / STEREO button (D/ST)
• DSP SIMULATION button (SIMU)
W7 PARTY button·················································(101)
W8 Monitor select button (M.SEL) ······················ (43)
W9 Video select button (V.SEL)··························· (60)
E0 Multi-zone power buttons···························· (106)
• Muiti-zone power on button (ON)
• Muiti-zone power off button (OFF)
E1 Device power buttons ··························· (109, 110)
• Device power on button (ON)
• Device power off button (OFF)
E2 System buttons······························(85, 109 ~ 111)
• Repeat button (RPT)
• Random button (RND)
• Disc skip up button (Skip+)
• Skip button (8, 9)
• Play button (1)
• Search button (6, 7)
• Still / Pause button (3)
• Stop button (2)
E3 QUICK SELECT button···························(101, 107)
E4 MACRO button ···············································(114)
W3 E0
E3
E0
E0
E4
E2
E1
The time for which the backlight stays on can
be changed (vpage 115 “Setting the Time the
Backlight Stays Lit”).
Getting Started