DENTAL HI TEC QuickSleeper5 User manual

To be read before firsT use
V17/10/2014 - UK
User GUide
www.mydentalhitec.com

Security Rules
(TO BE READ IMPERATIVELY BEFORE FIRST USE)
QuickSleeper® is an electronic dental anesthesia system designed for local injections before and/or during treatment.
QuickSleeper® is a modern alternative to traditional anesthesia syringes. The practitioner should take the usual precautions
to ensure the success of every dental anesthetic injection.
WARNINGS
It is forbidden to alter your Quicksleeper without the permission
of Dental Hi Tec. Should your QuickSleeper be modified, the
modification must be performed by a service center approved
by Dental Hi Tec, or by Dental Hi Tec’s technical Service. Control
and appropriate testing must be performed to ensure that your
device can still be used safely.
Using QuickSleeper with other equipment is under the
responsibility of the user dentist.
CONTRAINDICATIONS
There are no contraindications known until now.
GENERAL RECOMMENDATIONS
· Keep mobile phones at a minimum of 1.5 metres (5 feet)
from the control box, pedal or power supply; otherwise this
could disrupt the wireless communication of QuickSleeper®.
· QuickSleeper® must only be used by a qualified dental
surgeon.
· The anesthesia act requires constant supervision of the
registered practitioner who can remove the handpiece from
the injection site at anytime.
· Do not leave QuickSleeper® within reach of children.
· Do not expose your device to the sun or leave it near a
radiator or an air-conditioner.
· Do not expose QuickSleeper® to water or chemical
products.
· The plug of the power supply serves as a cut-off and must
remain accessible.
· Imperatively wear disposable surgical gloves when
manipulating and using QuickSleeper®.
PROTECTION AGAINST ELECTRIC
SHOCKS
· The connexion must be made on an alternative single-phase
circuit.
· The external voltage should be identical to that on the
material safety data sheet located under the control unit.
· The electrical installation must have a security circuit breaker.
· Before any use, check the condition of the plug and power
cable.
· Do not pull on the cable to remove the plug from the power
socket.
SECURITY LEVELS:
· Handpiece and control box cables: very low security voltage
(VLSV-24V).
RECOMMENDATIONS
FOR USE
ANESTHETIC
· Only use 1.7ml or 1.8ml glass anesthetic cartridges, with
plastic protection film to easily withdraw the cartridge in case
of breakage.
· Refer to the cartridge manufacturers’ recommendations to
know the quantities that can be injected per session.
SECURITY
· For security reasons, do not screw or unscrew
the needle close to your patients and protect
them with safety glasses.
CONTAMINATION
· Each QuickSleeper® needle, cartridge and accessory must
be used only on one single patient to prevent risks of cross
contamination.
· Never re-use the needles and anesthetic cartridges, each
of these items must be destroyed after use in an incinerator
allocated for this purpose.
· Always replace the container by a sterile container in case of
change of needle and/or cartridge during anesthesia.
· Do not leave the needles without protection. Systematically
replace the protection after use, using the recapping system
on the handpiece holder (p. 8).
DISINFECTION
· The containers must be disinfected and sterilised before each
anesthesia (see procedure p.17).
· The holder and handpiece must be disinfected after
each patient (see the indications of disinfectant product
manufacturers).
NEEDLE BREAKAGE
· Needle breakage is the result of an incorrect manipulation.
This breakage may be caused by one or several parameters :
see p. 21
2

Security rules 2
A progressive start up 3
Presentation of your QuickSeeper 4-5
DHT Needles 6
Installation 7-10
Functions 11-16
Maintenance 17-18
Annexes
Technical problems & solutions 19-24
Miscellaneous information 25-27
Contents
A progressive start up
for a successful integration…
Master the device before performing your first osteocentral or
transcortical anesthesia. Continue performing your standard
techniques but using the QuickSleeper.
• Get used to working with the pen grip, always using
good support points and a comfortable position.
• Perform completely painfree attached gum
anesthesias, infiltrations, intraligamentaries using, if necessary,
the needle rotation…
After these days of initiation, perform your first osteocentral or
transcortical anesthesias starting with simple cases, on the anterior
sectors, where the access and visibility are good.
Complementary information available on the website
www.mydentalhitec.com.
We wish you lots of success with the QuickSleeper.
Dear user,
QuickSleeper is going to enable you to perform all of your
anesthesias (intraosseous*, intraligamentary, intraseptal, infiltration,
ID Nerve Block…) with unmatched efficiency and comfort.
To prevent improper use of the device which could injure your
patient and damage your QuickSleeper, please read this
document carefully before first use.
* Intraosseous = osteocentral or transcortical
(Refer to the clinical guide for more details)

Aspiration
(countinuous press)
Injection mode selection :
Slow / Intraosseous / Fast
(short press)
Injection
(countinuous press)
Needle rotation
(countinuous press)
The functions of your QuickSleeper 5
3 information windows (quantity and injection speed)
Selected injection mode
Handpiece nose on which is screwed
a rotary or plastic container
”Screwing” key
(countinuous press)
”Unscrewing” key
(countinuous press)
”Return” key
(short press)
4
Presentation
iInformation concerning the wireless, batteryless pedal
All of the pedals have an “all or nothing” function.
The wireless pedal comes from cutting-edge research. The wireless connection is very reliable but like any radio system,
it can be disrupted by external factors: stainless steel furniture, close proximity to a high-power radio transmitter (mobile
phone), a disruptive electronic equipment (computer...). We recommend to carefully choose the location of the control
box and the wireless pedal so they can communicate without being disturbed.
Your pedal does not contain a battery. Your foot motion on the pedal generates the energy required to operate the
system. It is therefore mandatory to perform fast and frank pedal pressures and releases. Slow or incomplete motion may
not create enough energy to transmit the wireless information to the control box.
If a release of the pedal has no effect (rotation or injection remain active), simply press / release again the same pedal
to stop operation. The handpiece is under the constant supervision of the practitioner who must withdraw it from the
patient’s mouth in case of malfunction.

Power indicator
Maintenance
plug
24V Electric
power plug
Handpiece
plug
5
Description of the control box
24V Electric
power plug
(Ref. SE M0143_xx)
Control box
fixing adhesives
(Ref. SA0226)
Diagnostic maintenance
(only for technical service)
Diagnostic maintenance
(only for technical service)
Choice of
injection varient
Built-in lip-protector to prevent
hurting the patient during needle
rotation.
Transparent container to
perform aspirations
Needle cap
holder
Handpiece
holder
Plastic container
(Ref. SA5600)
Anesthesias without needle rotation.
(Infiltration, ID Nerve Block, palatal)
Rotary container
(ref. SA5500)
Anesthesias with needle rotation.
(osteocentral, transcortical,
intraligamentary)
Handpiece holder
(Ref. SA5610)
QuickSleeper 5 accessories
Rotary container lubricant
(Ref. SA5640)
DHT Needles
3 available dimensions:
Ø 0.30 (30G) - 9 mm
Ø 0.30 (30G) - 16 mm
Ø 0.40 (27G) - 16 mm
Presentation

DHT needles are the only ones responding to the constraints linked to bone
perforation and offering such a fine bevel.
Their specific bevels, contrary to those of standard needles, present identical cutting
properties to a scalpel blade. This brings forward 2 advantages:
- DHT needles incise the tissues instead of tearing them, allowing a pain free
penetration of the mucosa.
- They also have a superior perforation capacity than standard needles, with a much
lower obstruction rate. DHT Needles also present a specific hub indicator enabling
to correctly orientate the bevel during attached gum, palatal and intraligamentary
anesthesias.
(1) : To be priveliged when bone density is important and interdental space sufficient.
Type of needle : Ø 0.30 (30G) - 16 mm Ø 0.30 (30G) - 9 mm Ø 0.40 (27G) - 16 mm
Hub colour : White Green Yellow
Osteocentral Adults X X (1)
Osteocentral Children X
Transcortical X
Infiltration (free mucosa) X
Infiltration (attached mucosa) X X X
Intraseptal X
Intraligamentary X
Palatal X X
- Respect the model of needle corresponding to the type of anesthesia performed to obtain maximal results and
prevent needle breakages.
- Never put over 16 mm long needles into rotation.
- Consult the instructions in the boxes before use and read the security rules, “recommendations for use” (p. 2)
and “Needle breakage” (p. 21) chapters before using the needles.
6

Install your QuickSleeper 7
Installation

Installation
1. Put in place the pedal hoop
11
Never place the pedal under the dental chair during its descent to avoid crushing the pedal hoop
and damaging the chair.
2 2
OK
1 2 3
2. Handpiece holder installation
QuickSleeper is going to become the only instrument for all of your anesthesias.
The handpiece must therefore always be immediately accessible, as are your turbine and micromotor.
The handpiece holder is designed to be stuck on the right or left hand side of a vertical flat surface.
Always use this support to recap the needle without risk of cross-
contamination.
To prevent any risk of accidental pricking, never leave a needle
unprotected when the handpiece is in its holder. The holder must
be disinfected after each patient (see the indications of disinfectant
manufacturers).
Fixing the support
1 2 3 4 5 6
1
min.
OK
+ 24h
8

9
Installation
3. Control box installation
The control box is supplied with nonslip feet enabling it to be placed on a horizontal surface.
It can therefore be hidden below your instrument holder, on the side of a piece of furniture or of the unit (find some
installation models on www.mydentalhitec.com).
After fixing, wait 2
hours to not unstick
the adhesives.
Fix your control box
Wireless communication between the control box and pedal
Unfix your control box
+2h
mini.
To ensure good communication between the control box and wireless pedal avoid obstacles between
the 2 elements, especially metallic obstacles (computers, boxes). Do not fix /place the control box on an
electronic device (computer…). Keep mobile phones at a minimum of 1.5 metres (5 feet) from the control
box, pedal or power supply.
1 2 3 4 5
1 2 3
OK

10
5. To start, pause and stop your QuickSleeper
START :
QuickSleeper starts working as soon as you press one of the 4 pedals or handpiece buttons.
PAUSE :
QuickSleeper automatically goes into low-power mode as soon as the pedal is released.
STOP :
Turn off the main power supply of your installation or disconnect the QuickSleeper power supply. QuickSleeper can be
plugged in to the main power supply of your installation to be turned off every night.
4. Connection
1 2 3 4
Installation

Your QuickSleeper functions 11
Functions
To perform an intraosseous anesthesia with QuickSleeper,
use the following functions based on the chronology given:
1 Needle assembly ................................................................................................................................................ p.12
2 Injection mode selection .............................................................................................................................. p.13
3 Anesthetic injection (mucosa injection) ............................................................................................... p.13
4 Needle rotation (intraosseous penetration) ..................................................................................... p.14
5 Anesthetic injection (intraosseous injection) .................................................................................... p.13
6 Option : change needle (anesthesia on an other sector or obstructed needle)
and anesthetic injection ................................................................................................................................. p.12
7 Plunger return ...................................................................................................................................................... p.15
8 Needle disassembly ......................................................................................................................................... p.12
9 Cleaning, disinfection, sterilization ........................................................................................................... p.17
For the other types of anesthesia, adapt phases 2 to 6 ........................................................................ p.11

Functions
12
Hold the
needle cap
tightly
21
6
57
Hold the
needle cap
tightly
Axis to
respect
Push in up
to the stop
Needle assembly with a rotary container
(osteocentral, transcortical, intraligamentary, intraseptal)
Needle dissassembly (or exchange) with a rotary container
(osteocentral, transcortical, intraligamentary, intraseptal)
- Preferably use cartridges with a plastic film which limit the risk of breakage.
- Only use new 1.7 or 1.8 ml cartridges.
V Video version on www.mydentalhitec.com or QS5 application
V Video version on www.mydentalhitec.com or QS5 application
To save time, it is possible to unscrew the neeedle during the return of the plunger.
If the needle is blocked in rotation, unscrew the container very slightly to proceed with the unscrewing.
It is also possible to assemble and disassemble the needle manually (see p. 20).
i
4
1 3
4
7
Screwing OK
START (continuous press)
START (continuous press)
134°C
134°C
1
2
OK
2
See p. 17 + 18
6
3
5
”Beep”
”Beep”
STOP
STOP

13
Functions
V Video version on www.mydentalhitec.com or QS5 application
V Video version on www.mydentalhitec.com or QS5 application
Injection mode selection
Anesthetic injection
QuickSleeper features 3 injection modes to adapt itself for all your anesthesias. The injection
mode selection is made by successively pressing the ”Injection mode” pedal.
Lo Mode (Low) :
slow speed intended for intraligamenatary, intraseptal and palatal injections or very
sensitive patients.
The rotation is active.
The speed of injection is slow (see diagram 1).
This mode has an injection varient with a slower accelaration (dotted curve). This option can
be selected on the control box as defined p.16.
IO Mode (IntraOsseous) :
speed intended for intraosseous injections (osteocentral and transcortical).
The rotation is active.
In this mode, QuickSleeper adapts the speed of injection based on the use of the rotation
pedal.
BEFORE using the rotation pedal, QuickSleeper injects in slow constant speed for a painfree
attached gum anesthesia (see diagram 2).
AFTER using the rotation pedal (cortical perforation), QuickSleeper injects in progressive
speed for a comfortable, optimal, intraosseous injection (see diagram 3).
This mode has an injection varient with a slower speed (dotted curve). This option can be
selected on the control box as defined p.16.
If you wish to reactivate the slow injection speed after using the rotation, use the ”injection
mode” pedal until you have reselected the IO mode.
Hi Mode (High) :
fast speed intended for infiltration and ID Nerve Block injections.
In this mode, the rotation is disabled.
The injection speed is fast (see diagram 4).
This mode has an injection varient with a slower start (dotted curve). This option can be
selected on the control box as defined p.16.
If the lights do not come on, stop the injection.
Refer to the cartridge manufacturers’ recommendations to know the quantities that can be injected per session.
You can change mode at any time.
i
Lo Mode
Injection varient (option)
1
IO Mode : Injection speed BEFORE using the
rotation pedal
Injection varient (option)
2
Hi Mode
Injection varient
(option)
4
2
”Beep”
”Beep”
”Beep”
”Beep”
”Beep”
”Beep”
Automatic
plunger
return
The sound signals are given as an indication
only, use only the lights to confirm the
quantity injected.
The flash rate of the 3 lights is proportional
to the injection speed.
IO Mode : Injection speed AFTER using the
rotation pedal
Injection varient (option)
3
1
START (continuous press) STOP
1

14
Functions
QuickSleeper emits a ”beep” during the perforation? The rotation slows down?
You are pressing too hard on the needle, which reduces the efficiency of the perforation. Continue perforating while
reducing the pressure on the needle until the sound signal stops and the speed returns to normal.
The sound signal persists? The rotation slows down?
QuickSleeper indicates that the needle is probably obstructed.
Change needle, container and cartridge (see p.12) and start the perforation again by pressing as little as possible on the
needle or by changing injection site.
If the needle is blocked in rotation, unscrew the container very slightly to proceed with the needle screwing/unscrewing.
Recommended number of rotations :
- For osteocentrals or transcorticals, do not exceed 10 rotation cycles* to avoid bone heating.
After 10 rotation cycles, a «beep» will be emitted for each extra rotation cycle.
- For intraligamentaries, do not exceed one rotation cycle* to obtain a deep penetration.
For safety reasons, the needle rotation is disabled in «Hi» mode.
Needle rotation
(* 1 rotation cycle = rotation during 1 sec. followed by an automatic stop during 1 sec.)
1 2 3
Rules to respect for the perforation :
1. Make sure that the needle is not eccentric by testing the perforation outside of the mouth.
2. Always make bone contact before starting the rotation to prevent damaging the superficial
tissues.
3. Use solid support points to prevent changing angulation during the perforation.
4. Do not use the rotation to withdraw the needle from the bone to prevent any risk of needle
breakage.
Osteocentral anesthesia without rotation for children:
Frequently with children the penetration into the cancellous bone can be made without needle
rotation. In this case the intraosseous injection speed will not be activated. Therefore, for children
where you believe it will be possible to penetrate the needle without rotation, you should:
• perform the attached gum anesthesia in IO mode.
• activate the intraosseous speed by a SHORT press on the rotation pedal. This speed will be
active as soon as you hear a «beep» (do not prolong the pressure to avoid starting the needle rotation).
• proceed with the penetration into the cancellous bone, using the rotation only if necessary.
• perform the intraosseous injection (the quantity lights flicker faster confirming the injection in osteocentral speed).
The rotation is discontinuous to feel the progress of the needle in the bone and to avoid overheating.
QuickSleeper injects all through the rotation phase to limit needle obstruction by osseous fragments.
i
STOP
”Beep”
START (continuous press)
V Video version on www.mydentalhitec.com or QS5 application

15
Functions
Plunger return (once the anesthesia is complete)
1 3
OK
”Beep”
2
The return is automatic when a complete cartridge is injected.
i
V Video version on www.mydentalhitec.com or QS5 application
32
4
1 4
2
5
1
Unscrewing
Screwing
OK
3
134°C
134°C
5
See p.18
The rotation and motor-assisted screwing do not work with the transparent plastic container.
Needle screwing/unscrewing on transparent plastic container
(infiltration, ID Nerve Block, palatal)

16
Functions
Aspiration before complete injection (infiltration, ID Nerve Block)
Injection varient selection
21 3 4
6
INJECT
MINIMUM
1/8 TO 1/4
MARCHE
1
SELECT THE MODE
TO MODIFY
2a
2b
Verify the
absence of
blood in the
anesthetic
cartridge
”Beep”
”Beep”
STOP
STOP
START (continuous press)
START (continuous press) 5
Speed details p.13
”Beep” ”Beep”
= injection varient
”Beep”
= standard injection

QuickSleeper maintenance
Download a copy of this document on www.mydentalhitec.com
Verify that the container is free of lubricant and dirt.
Clean by soaking. Place the container in a disinfectant
solution such as “Quaternary amonium” and use ultrasonics
during 8 min.
Place the container in demineralized water for 2 min.
and gently brush with a soft brush.
Store the sterile items in a dry and dustless place.
Put the container into the washer disinfector
(Disinfection phase for 5 min – 90°C (194°F))
Rince thoroughly with demineralized water*
for minimum 20 min.
Verify that the container is free of lubricant and dirt.
Spray the container with demineralized water.
Dry the container with a non-woven compress (or with
compressed air).
*Remove all traces of disinfectant
to avoid an accelerated deterioration of plastic parts (cartridge
holder inside the container) during auto-claving.
Demineralized water prevents mineral deposits which can
affect the operation of rotary container.
These deteriorations are not covered by the warranty.
LUBRICATE BEFORE EACH STERILZATION (SEE LUBRICATION PROCEDURE ON THE NEXT PAGE)
CHOICE 1 :
AUTOMATIC CLEANING
CHOICE 2 :
MANUAL CLEANING WITH ULTRASONICS
Put the container in a sterile packaging according to EN 868-5.
Steam sterilization B class (pre and post vacuum) with an autoclave sterilizator in compliance with EN 13060 norm.
Sterilization time of minimum 18 min. at 134°C.
Check that the container retrieved is dry and sterile.
Steps for cleaning / disinfection / sterilization of the rotary containers
To be given to the person in charge of sterilization

17
* Follow the standard compliances and specific guidelines of your country.
Maintenance
134°C
134°C
This is the procedure to follow before first use and after each anesthesia.

- Unplug the device from the mains before cleaning.
- Clean the handpiece holder with a disinfectant product after each patient.
- Clean the components (control box, pedal, handpiece) with a clean cloth and alcohol solution placed on the
cloth.
Never spray a cleaning product directly on components.
Steps for cleaning / disinfection / sterilization and storage of the plastic containers
Control box, handpiece, handpiece holder and pedal cleaning
Place the container in demineralized water for 2 min. and gently brush with a soft brush.
Rince thoroughly with demineralized water for minimum 20 min.
Verify that the container is free of dirt.
Spray the container with demineralized water.
Dry the container with a non-woven compress (or with compressed air).
Put the container in a sterile packaging according to EN 868-5.
Steam sterilization B class (pre and post vacuum) with an autoclave sterilizator in compliance with EN 13060 norm.
Sterilization time of minimum 18 min. at 134°C.
Check that the container retrieved is dry. Store the sterile items in a dry and dustless place.
Clean by soaking. Place the container in a disinfectant solution such as “Quaternary amonium”
and use ultrasonics during 8 min.
- Never use powerful solvents or aggressive chemical solutions.
- Never sterilize the control box, handpiece, handpiece holder or pedal.
- Avoid the projections of liquid on the control box, the handpiece or the pedal. Never immerse the
control unit, handpiece or pedal in liquid.
Failure to respect these rules can produce irreversible deteriorations which are not covered by the
warranty.
Rotary container lubrication procedure
A lack of lubricant can considerably increase the noise during the rotation and rapidly degrade the
rotation mechanism. This is not covered by the warranty.
Consult the lubricant product sheet on page 27.
* Follow the standard compliances and specific guidelines of your country.
18
1 2 43
x 1
134°C
134°C
Maintenance
1
2

Technical problems and solutions
QuickSleeper 5
19
Annexes

Find videos on www.mydentalhitec.com
If it is impossible to unscrew the needle mechanically (due to a long perforation), unscrew the needle manually.
Difficult insertion of the cartridges into the rotary container
The sizes of anesthetic cartridges vary a lot, even within the same box.
Cartridges with a wider external diameter can be harder to insert into the rotary container. This can cause a reduction in
the quality of rotation.
In this case, change your cartridge and keep the non-compliant cartridges for anesthesias with the plastic container
(infiltration and ID Nerve block).
Impossible / incomplete screwing of the container
2 possibilities:
1. Verify that the plunger is in its starting position by pressing on the ”plunger return” key.
2. The cartridge is too long or too full. In this case, perforate the cartridge cap with the needle to evacuate some
anesthetic and enable the complete screwing of the container.
Plastic cartridges are incompatible with the QuickSleeper rotation system.
20
Accessories
To unscrew the needle manually
1
2
2
3 4
2
5 6
134°C
134°C
1
See p. 17
+ 18
1 32
1
Annexes