Denver IFM-15 User manual

E-2
iPod DOCKING HIGH FIDELITY
SPEAKER SYSTEM
WITH FM PLL RADIO TUNER
AND ALARM CLOCK
OPERATING INSTRUCTIONS
WAR NI NG : To reduce
the risk of electric shock, do
not remove cover (or back).
No user-serviceable
p a r t s i n s i d e . R e f e r
servicing to qualified
service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The excl am at ion
poi nt withi n the
triangle is a warning
sign alerting you of
important instructions
accompanying the
product.
The lightning flash
and arrowhead
within the triangle
i s a w a r n i n g
sign alerting you of
"dangerous voltage"
inside the product.
NOTE: CAUTION SYMBOLS ARE PRINTED ON THE BOTTOM OF UNIT.
PLEASE REFER TO INSTRUCTION MANUAL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS.
CAUTION: GROUNDING OR POLARIZATION. THE PRECAUTIONS
SHOULD BE TAKEN SO THAT THE WIDER BLADE OF THE AC PLUG
MUST MATCH THE SLOT IN RECEPTACLE "WALL SOCKET".
MODEL: IFM-15
R

E-4
E-3
LOCATION OF CONTROLS
1. SPEAKER
2. BLUE BACKLIT DISPLAY
3. BACK-UP BATTERY
COMPARTMENT (BOTTOM OF UNIT)
4. CAVITY FOR DOCK ADAPTOR
5. DOCK ADAPTOR FOR iPOD
(SEVERAL DIFFERENT ADAPTORS
ARE PROVIDED)
6. VOLUME DOWN ( ) KEY
7. VOLUME UP ( ) KEY
8. MEMORY KEY
9. EQ/ SLEEP KEY
10. ON/ OFF KEY
11. SKIP ( ) / SEARCH ( ) KEY
12. SKIP ( ) / SEARCH ( ) KEY
13. AL-SET/ AL-MODE KEY
14. FUNCTION/ CL-SET KEY
15. PLAY/ PAUSE / STEREO/ MONO KEY
16. SNOOZE DIMMER KEY
17. AUX INPUT SOCKET
18. HEADPHONES SOCKET
19. DC JACK (DC 7.5V )
20. FM ANTENNA WIRE
PREPARATION OF iPod DOCK
TO CONNECT AN iPod WITH A DOCK CONNECTOR TO THIS UNIT, FIRST INSERT THE DOCK
ADAPTOR THAT FITS YOUR iPod, AND THEN CONNECT YOUR iPod. YOUR HIFI INCLUDES
DOCK ADAPTORS THAT WORK WITH SEVERAL MODELS OF iPod WITH DOCK CONNECTORS.
IF YOU WANT TO CONNECT A DIFFERENT MODEL OF iPod AT A LATER TIME, YOU CAN EASILY
REMOVE THE DOCK ADAPTOR FROM YOUR SPEAKER SYSTEM USING A FINGERNAIL,
AND INSERT THE ADAPTOR THAT FITS THE NEW iPod. IF THERE IS NO DOCK ADAPTOR
FOR YOUR MODEL OF iPod INCLUDED WITH YOUR SPEAKER SYSTEM, AN ADAPTOR MAY
HAVE BEEN INCLUDED WITH YOUR iPod.
PLEASE CHECK INSIDE THE BOX OF THE iPod YOU PURCHASED FOR A PLASTIC DOCK
ADAPTOR.
AC OPERATION (EXTERNAL AC-DC POWER ADAPTOR)
- THIS SET IS EQUIPPED WITH A "DC-JACK" CAPABLE OF ACCEPTING
AC-ADAPTORS WITH A RATING OF DC = 7.5V, 1.5A, AND WITH A PLUG
WITH THE FOLLOWING POLARITIES AS SHOWN (CENTER POSITIVE) :
- PLEASE USE ONLY THE SUPPLIED AC-ADAPTOR TO OPERATE THE UNIT.
USE OF OTHER ADAPTORS MAY DAMAGE THE UNIT OR CAUSE IT TO MALFUNCTION.
- PLUG THE TAIL END OF THE AC-ADAPTOR INTO THE DC-JACK (SOCKET)
ON THE REAR OF THE UNIT.
- INSERT THE PLUG OF THE AC-ADAPTOR INTO A WALL OUTLET WITH AC-POWER.
- PRESS THE "ON/ OFF" KEY TO SWITCH ON THE UNIT.
- THIS UNIT IS DESIGNED TO OPERATE WITHOUT EVER BEING TOTALLY POWERED "OFF".
IT WILL EITHER BE "ON" OR IN "STANDBY MODE".
- IN STANDBY MODE, THE BLUE BACK-LIGHT OF THE DIGITAL DISPLAY WILL BE DIMMED
BUT THE DISPLAY WILL SHOW THE CURRENT TIME (CLOCK FUNCTION).
- ANYTIME DURING STANDBY MODE, YOU CAN SWITCH "ON" THE UNIT BY PRESSING
THE "ON/ OFF" KEY.
- SAVE ENERGY BY SWITCHING THE SYSTEM TO "STANDBY" MODE WHEN NOT IN USE.
POWER SUPPLY
- - -
FRONT VIEW:
BACK VIEW:
1
2
TOP VIEW:
3
678
45
9 10
11 12 13 14 15
16
17
18
19
20
- OPEN THE BATTERY DOOR AT THE BOTTOM OF UNIT.
- INSERT 2 PCS "AAA-CELL" (UM-4/LR03 TYPE) BATTERIES IN THE BATTERY
COMPARTMENT.
THESE 2 BATTERIES ARE FOR BACKUP OF THE "CLOCK" DURING BRIEF POWER
OUTAGES".
BACK UP BATTERIES
-
+
DIMMER FUNCTION
THIS SET HAS A DIMMER FUNCTION TO ADJUST THE BRIGHTNESS LEVEL
OF THE DISPLAY BACKLIGHT. SIMPLY ADJUST IT AS DESIRED BY PRESSING
THE SNOOZE/ DIMMER KEY REPEATEDLY (HI-DIMMER / LOW-DIMMER / OFF.)
TO REDUCE EYE STRAIN, AND TO SAVE ENERGY.
THE DISPLAY BACKLIGHT WILL ALWAYS RETURN IN HI-DIMMER AFTER RESET THE UNIT.

E-6
DIGITAL CLOCK FUNCTION
- THE SET HAS A BUILT-IN DIGITAL CLOCK, WHEN THE SET IS IN "STANDBY MODE".
(THE DISPLAY WILL CONTINUOUSLY SHOW THE CURRENT TIME).
IN THIS SITUATION THE BLUE BACKLIT IS NORMALLY DIMMED (TO SAVE ELECTRICITY).
HOW TO SET CORRECT TIME:
CORRECT TIME IS NOW SET & WILL BE SHOWN IN THE DISPLAY.
SWITCH UNIT TO "STAND-BY" MODE (DISPLAY LIGHT = DIMMED)
PRESS & HOLD FUNC./ CL-SET KEY FOR 3 SECONDS DISPLAY SHOWS
HOUR OR HOUR (FLASHING)
12H 24H
PRESS SKIP- / SEARCH- OR SKIP+ /SEARCH+ KEY TO SELECT
12-HOUR OR 24-HOUR CLOCK DISPLAY SYSTEM & PRESS FUNC./CL-SET KEY
TO CONFIRM YOUR SELECTION
PRESS REPEATEDLY TO
SET THE CORRECT MINUTE IN THE DISPLAY & PRESS
TO CONFIRM
SKIP- / SEARCH- OR SKIP+ /SEARCH+ KEY
FUNC./ CL-SET KEY
PRESS REPEATEDLY TO
SET THE CORRECT HOUR IN THE DISPLAY & PRESS
TO CONFIRM
SKIP- / SEARCH- OR SKIP+ /SEARCH+ KEY
FUNC./ CL-SET KEY
E-5
If there is no dock adapter for your model of iPod included, you can also
use the dock adapter which was included in the box with your iPod itself.
Dock adapters: Choose the dock adapter that fits your iPod.
Your iPod fits snugly into the correct adapter.
FOR OTHER iPod MODELS:
17
14
16
OR
10
OR 9
10
OR 9
THE NUMBER
SHOWS WHICH iPod FITS
1518

SNOOZE FUNCTION
- WHENEVER THE ALARM COMES ON, IT CAN BE TEMPORARILY SUSPENDED
FOR A SHORT PERIOD OF 5 MINUTES, BY PRESSING THE “SNOOZE/ DIMMER” KEY
ONCE.
- THE ALARM WILL THEN AUTOMATICALLY COME ON AGAIN AFTER THE 9 MINUTES
“SNOOZE” PERIOD HAS ENDED.
- THE PROCEDURE CAN BE REPEATED FOR APPROXIMATELY 90 MINUTES FROM
ORIGINAL ALARM WAKE-UP TIME.
E-7
E-8
7. THE SET WILL NOW AUTOMATICALLY SWITCH "ON" AT THE WAKE-UP TIME AS YOU
HAVE CHOSEN, AS LONG AS THE ALARM FUNCTION IS "ACTIVE".
8. TO TURN OFF THE UNIT AFTER IT HAS AUTOMATICALLY SWITCHED ON,
SIMPLY PRESS THE ON/OFF KEY ONCE. THIS WILL SWITCH OFF THE SET
BUT WILL NOT CLEAR THE ALARM SETTINGS, AND THE SET WILL SWITCH ON
AGAIN AUTOMATICALLY ON THE NEXT DAYAT EXACTLY THE SAME PRESET TIME.
9. TO DEACTIVATE THE ALARM, PRESS & RELEASE THE AL-SET/ AL-MODE KEY. THE
ALARM SYMBOL "AL" DISAPPEARS FROM THE DISPLAY.
10. TO ACTIVATE THE ALARM AGAIN, REPEAT THE PROCEDURE OF "ALARM TIME
SETTING" AS DESCRIBED.
IMPORTANT:
IF THE ALARM IS SET AS WAKE TO iPod, YOU WILL NEED TO CONNECT THE iPod
PROPERLY AS DESCRIBED. OTHERWISE, THE BUZZER ALARM WILL SOUND AT THE
SET TIME IF THE iPod HAS NOT BE CONNECTED.
90
MINS 80 MINS 70 MINS 60 MINS 50 MINS OFF*
40
MINS 30 MINS 20 MINS 10 MINS
- THIS SET HAS A SPECIAL SLEEP TIMER FUNCTION WHICH CAN AUTOMATICALLY
SWITCH OFF THE UNIT. THIS IS USEFUL FOR SLEEPING TO MUSIC AT NIGHT.
- AT ANY TIME WHILE THE UNIT IS OPERATING, PRESS & HOLD THE EQ/SLEEP KEY
UNTIL THE "SL" SYMBOL FLASHING, THEN PRESS THE EQ/SLEEP KEY REPEATEDLY
TO CHOOSE THE AUTOMATIC POWER OFF TIME.
(*OFF MEANS SLEEP TIMER IS DEACTIVATED)
ALARM FUNCTION
- THIS SET IS EQUIPPED WITH 3 ALARM MODES: BUZZER, RADIO AND iPod.
BEFORE SETTING THE ALARM, MAKE SURE TO SET THE CLOCK (SEE "DIGITAL
CLOCK FUNCTION" IN THE PERVIOUS SECTION) .
PREPARE FOR THE ALARM SETTINGS
PRESS THE ON/ OFF KEY TO SWITCH ON THE SET (DISPLAY BLUE LIGHT WILL
BE "ON").
CURRENT TIME
12:00 ALARM SYMBOL
6. THE ALARM TIME IS NOW FULLY PROGRAMMED AND THE ALARM SYMBOL WILL
APPEAR TO INDICATE THAT THE ALARM FUNCTION IS "ACTIVE".
(DISPLAY SHOWS AS FOLLOWS WITH BLUE BACKLIGHT "DIMMED")
AUTOMATIC POWER OFF SLEEP FUNCTION
THE ALARM SET-UP MODE, WHERE THE SYMBOL"AL" IS FLASHING, WILL TIME-OUT
IF THERE IS NO INPUT FOR 3 SECONDSAND RETURN TO “STANDBY MODE”.
SHOULD THEALARM SET-UP MODE TIME-OUT, THE ALARM SYMBOL"AL" WILL NOT BE
DISPLAYED AND THEALARM TIME SETTING INSTRUCTIONS WILL HAVE TO BE REPEATED
FOR THEALARM TO BE SET.
1
(BLUE LIGHT DIMMED).
2. PRESS AND HOLD AL-SET/ AL-MODE KEY UNTIL
THE DISPLAY WILL NOW SHOW:
3. PRESS SKIP- / SEARCH- AND SKIP+ /SEARCH+ KEY TO REACH THE HOUR
OF THE DESIRED WAKE UP TIME THEN PRESS AL-SET/ AL-MODE KEY TO CONFIRM.
THE DISPLAY WILL NOW SHOW:
. PRESS THE ON/OFF KEY TO PUT THE SET INTO "STANDBY" MODE
00 00
HOUR (FLASHING)
MINUTES
(FLASHING)
8 00
4. PRESS SKIP- / SEARCH- AND SKIP+ /SEARCH+ KEY TO REACH THE
MINUTES OF THE DESIRED WAKE UP TIME, THEN PRESS THE AL-SET/ AL-MODE
KEY TO CONFIRM.
"ALARM" TIME SETTING
ONCE THE DESIRED SOURCE HAS BEEN READY, PRESS THE ON/ OFF KEY TO PUT THE
SET INTO STANDBY MODE AND THEN SHORT PRESS THE AL-SET/ AL-MODE KEY
REPEATEDLY TO SELECT THE SOURCE AS DESIRED.
"ALARM" MODE SETTING
NOW SELECT THE SOURCE THAT YOU WISH THE UNIT TO PLAY AT THE "WAKE UP"
TIME AS BELOW:
PRESS THE ON/ OFF KEY TO SWITCH ON THE SET (DISPLAY BLUE LIGHT WILL
BE "ON").
1. FOR iPod : CONNECT THE iPod AS DESCRIBED.
FOR RADIO : TUNE IN THE DESIRED STATION.
2. ADJUST THE VOLUME LEVEL AS DESIRED BY PRESSING VOL. UP + OR VOL. DN -
KEY.
SELECT THE SONG OR THE DESIRED PLAYLIST TO PLAY AT THE
“WAKE UP” TIME.
START AND PAUSE PLAYBACK OF THE SONG/PLAYLIST AT THE POINT
FROM WHICH YOU WANT PLAYBACK TO BEGIN AT THE “WAKE UP” TIME.
*REMARK: = BUZZER ALARM / = RADIO / = iPod
AL FM iPod
AL
iPod
FM
FLASHING
FM SYMBOL FLASHING
iPod SYMBOL

E-9 E-10
ELECTRONIC VOLUME CONTROL
- THIS UNIT USES AN ELECTRONIC VOLUME CONTROL .
- TO INCREASE OR DECREASE THE LOUDNESS OF UNIT, PRESS
THE VOLUME UP (VOL +) OR VOLUME DOWN (VOL -) KEYS RESPECTIVELY.
- RELEASE THE KEY WHEN VOLUME LEVEL IS AT THE DESIRED LOUDNESS.
- SOMETIMES, ESPECIALLY DURING LISTENING TO THE RADIO, YOU MAY NOTICE
A "CLICK-CLICK-CLICK" (REPEATING) SOUND WHEN YOU ARE INCREASING OR
DECREASING THE VOLUME. THIS IS A NORMAL CONDITION & THE SOUND WILL
DISAPPEAR WHEN YOU RELEASE THE VOLUME KEY (WHEN YOU REACH THE
DESIRED VOLUME LEVEL).
(PUSH BUTTON TYPE)
RADIO MEMORY (STATION PRESET MEMORY STORAGE)
- AT ANY TIME, THE CURRENTLY DISPLAYED STATION OR FREQUENCY CAN BE
STORED INTO ONE OF THE MEMORY POSITIONS.
- PRESS MEMORY KEY UNTIL "C01" FLASHES IN THE DISPLAY.
- PRESS SKIP- /SEARCH- AND SKIP+ /SEARCH+ KEYS TO SELECT DESIRED
MEMORY POSITION. (THERE ARE TOTAL 30 MEMORY POSITIONS).
- PRESS MEMORY KEY ONCE TO SAVE THE SELECTED STATION INTO THE
SELECTED MEMORY POSITION.
- TO RECALL ANY SAVED MEMORY, SIMPLY PRESS SKIP- /SEARCH- AND
SKIP+ /SEARCH+ KEYS THE SAVED RADIO-BAND WILL BE RECALLED.
- TO CLEAR THE MEMORY OF ANY POSITION, SIMPLY SAVE A NEW STATION TO THE
SAME MEMORY POSITION.
OPERATION OF RADIO
AUTOMATIC FREQUENCY ADJUSTMENT (SEEK MODE)
- PRESS AND HOLD (FOR 2 SECONDS) THE SKIP- /SEARCH- AND
SKIP+ /SEARCH+ KEYS TO “SEEK” (AUTOMATICALLY ADJUST) THE RADIO
FREQUENCY “UP” OR “DOWN” TO THE NEXT AVAILABLE RADIO STATION.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY OF THE NEXT
STATION THAT IS FOUND.
- WHEN A DESIRED STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE
“MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
- PRESS THE "ON/ OFF" KEY ONCE TO SWITCH ON THE UNIT.
- PRESS THE FUNC./CL-SET KEY REPEATEDLY UNTIL THE DISPLAY SHOWS "FM".
- EXTEND AND ADJUST THE FM-WIRE ANTENNA TO OBTAIN THE BEST RECEPTION.
- USE THE ST/MO KEY TO SELECT THE DESIRED MODE (STEREO/ MONO).
IN SOME CASES, WHERE RECEPTION IS POOR, IT MAY BE ADVISABLE TO
SELECT “MONO” MODE, TO IMPROVE CLARITY OF THE RADIO SIGNAL.
MANUAL FREQUENCY ADJUSTMENT (SCAN MODE)
- PRESS (AND IMMEDIATELY RELEASE) THE SKIP- /SEARCH- AND
SKIP+ /SEARCH+ KEYS TO “SCAN” (MANUALLY ADJUST) THE RADIO
FREQUENCY “UP” OR “DOWN” BY 1-STEP AT A TIME.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH
STEP’S POSITION.
- WHEN A DESIRED FREQUENCY OR STATION IS REACHED. IT CAN BE SAVED INTO
ONE OF THE “MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
MUSIC EQUALIZER
- AT ANYTIME DURING PLAYBACK, PRESS KEY REPEATEDLY TO
CHOOSE THE DESIRED SOUND EFFECT ACCORDING TO THE MUSIC YOU ARE
LISTENING TO :
EQ/SLEEP
E-0 = EQ OFF E-1 = CLASSIC
IMPORTANT
PLEASE NOTE THAT WHEN CONNECTING A iPod VIDEO, THE ERROR MESSAGE
“THE CURRENTLY ATTACHED ACCESSORY IS NOT SUPPORTED BY THIS iPod.”
WILL BE DISPLAYED AS THERE IS NO VIDEO INPUT/OUTPUT. HOWEVER,
ALL AUDIO FUNCTIONS WILL OPERATE NORMALLY AS OUTLINED ABOVE.
OPERATION WITH THE iPod
- TURN ON BOTH THE UNITAND THE iPod.
- CONNECT THE iPod TO THE UNIT AS DESCRIBED.
- PRESS THE FUNC./ CL-SET KEY REPEATEDLY UNTIL THE DISPLAY SHOWS “iPod”.
- PRESS THE PLAY/ PAUSE KEY ON THE UNIT, THEN THE FIRST SONG WILL
START PLAYING.
- THE iPod DISPLAY WILL INDICATE THE INFORMATION OF THE CURRENT SONG.
- YOU CAN OPERATE THE iPod USING EITHER THE UNIT'S BUTTONS, OR DIRECTLY
WITH THE iPod ITSELF.
- WHEN THE iPod HAS BEEN CONNECTED WITH THE UNIT, IT WILL START CHARGING
THE BATTERY OF THE iPod.
- NEVER REMOVE (OR UNPLUG) THE iPod FROM THE SET DURING PLAYBACK,
ALWAYS PAUSE PLAYBACK FIRST AND THEN PRESS THE FUNC/ CL-SET KEY TO SWITCH
TO ANOTHER SOURCE (EG. “RADIO” OR “AUX”) BEFORE REMOVING OR UNPLUGGING
THE iPod, TO PREVENT DAMAGE TO YOUR SONG FILES OR MEMORY DEVICES.
- AT ANYTIME DURING PLAYBACK, PRESS THE PLAY/PAUSE KEY TO PAUSE
PLAYBACK. PRESS PLAY/PAUSE KEY TO RESUME PLAYBACK OF THE SAME
SONG & POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS AND RELEASE THE SKIP- /SEARCH-
OR SKIP+ /SEARCH+ KEYS TO SKIP FORWARD OR BACKWARDS BY ONE SONG,
AS DESIRED.
- AT ANYTIME DURING PLAYBACK, PRESS AND HOLD THE SKIP- /SEARCH-
OR SKIP+ /SEARCH+ KEYS TO FAST-FORWARD (CUE) OR FAST-REVERSE (REVIEW)
THE SPECIFIC SONG, WHICH IS CURRENTLY PLAYING.
E-2 = JAZZ
E-3 = ROCKE-4 = POP

E-11
USING THE AUDIO LINE IN CONNECTION (AUX-INPUT)
- YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A MP3
PLAYER OR A TV TO THIS UNIT, TO LISTEN TO THE SOUND OF THAT DEVICE
THROUGH THE HIGH QUALITY AMPLIFIER OF THIS MUSIC SYSTEM.
- TO CONNECT THE EXTERNAL DEVICE PLEASE USE A STANDARD STEREO
HEADPHONE (3.5MM TO 3.5MM PLUGS) CABLE TO CONNECT THE
"HEADPHONE-OUT OR AUDIO LINE-OUT" OF THE DEVICE TO THE AUX-INPUT SOCKET
OF THIS UNIT.
- SWITCH THE FUNCTION TO "AU" (AUX) USING THE FUNC./CL-SET KEY.
- SWITCH ON THE UNIT AND THE EXTERNAL DEVICE (eg. MP3-PLAYER OR TV).
- START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME CONTROL
OF THE MAIN UNIT TO THE DESIRED LEVEL.
- REMEMBER TO SWITCH OFF THE UNIT WHEN YOU ARE FINISHED USING THE
EXTERNAL DEVICE.
SPECIFICATIONS
POWER SUPPLY : ............... DC 7.5V, 1.5A THOUGH BUILT-IN DC JACK
EXTERNAL AC-DC POWER ADAPTOR 110V-240V ~ 50/60Hz
POWER CONSUMPTION : .... 10 W
SPEAKER : ........................... SPEAKER 2" x 2
FREQUENCY : ..................... FM 87.5 - 108 MHz
WHEN ELECTROSTATIC DISCHARGE (ESD) OCCURS AT THE FRONT SURFACE (WHETHER
METAL OR PLASTIC) OR NEAR ANY PART OR ANY BUTTON OF THIS UNIT, OR AT THE USB
PORT AND/ OR SD-CARD SLOTS (IF THEY EXIST ON THIS PRODUCT),
THERE MAY BE A POSSIBILITY THAT THE PRODUCT MAY STOP OPERATION AND/ OR
SHUT DOWN IMMEDIATELY. THIS IS A NORMAL CONDITI ON AND INTENDED TO PROTECT
THE UNIT AND INTERNAL COMPONENTS AGAINST DAMAGE.
IN SUCH A CASE, PLEASE RESET THE UNIT (BY DISCONNECTING AND RECONNECTING
AC-POWER SOURCE) TO REVERT THE UNIT TO NORMAL OPERATION.
ELECTROSTATIC DISCHARGE (ESD) PRECAUTION
BATTERY SHOULD NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE,
FIRE OR THE LIKE.
THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS
FILLED WITH LIQUIDS SHOULD BE PLACED ON THE APPARATUS.
THE MARKING AND RATING LABEL IS LOCATED AT BOTTOM ENCLOSURE OFTHE APPARATUS.
THE MAINS PLUG IS USED AS THE DISCONNECT DEVICE AND IT SHALL REMAIN READILY
OPERABLE. TO BE COMPLETELY DISCONNECTED THE POWER INPUT, THE MAINS PLUG
OF THE APPARATUS SHALL BE DISCONNECTED FROM THE MAINS COMPLETELY.
THE MAINS PLUG SHOULD NOT BE OBSTRUCTED OR SHOULD BE EASILY ACCESSED
DURING INTENDED USE.
UNDER THE INFLUENCE OF ELECTROSTATIC PHENOMENON,
THE PRODUCT MAY MALFUNCTION AND USER TO POWER RESET.
EXCESSIVE SOUND PRESSURE FROM EARPHONES AND HEADPHONES CAN
CAUSE HEARING LOSS.
CAUTION
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.
ALL RIGHTS RESERVED
DENVER ELECTRONICS A/S
WWW.DENVER-ELECTRONICS.COM
E-12
INSTRUCTIONS ON ENVIRONMENT PROTECTION
Electric and electronic equipment contains materials, components and
substances that can be hazardous to your health and the environment,
if the waste material (discarded electric and electronic equipment) is not
handled correctly.
Electric and electronic equipment is marked with the crossed out trash
can symbol, seen below. This symbol signifies that electric and electronic
equipment should not be disposed of with other household waste, but
should be disposed of separately.
All cities have established collection points, where electric and electronic
equipment can either be submitted free of charge at recycling stations
and other collection sites, or be collected from the households. Additional
information is available at the technical department of your city.