Desa Proflame Series Instruction Manual

Desa Heating LLCDesa Heating LLC
Proflame Series OperationProflame Series Operation

Control ComponentsControl Components
Desa Proflame units, LMFP33 and LDL39 series
have two integral control components –the remote
and the receiver unit.

Remote ControlRemote Control
nn Allows adjustment of BTUAllows adjustment of BTU
output (flame height)output (flame height)
nn Allows thermostaticAllows thermostatic
operation of the heater.operation of the heater.
nn Allows sleep timerAllows sleep timer
operation in 15 minuteoperation in 15 minute
intervals up to 90 minutes.intervals up to 90 minutes.

Remote (cont.)Remote (cont.)
nn BTU/FlameBTU/Flame
height controlheight control
nn ThermostaticThermostatic
FunctionFunction
nn Timer functionTimer function
nn IndicatorIndicator

Remote (cont.)Remote (cont.)
nn U ses three “A A A ” U ses three “A A A ”
batteries.batteries.
nn ProgrammableProgrammable
addresses to avoidaddresses to avoid
conflict with otherconflict with other
remote devicesremote devices

ReceiverReceiver
nn Connects to gas valveConnects to gas valve
stepper motor tostepper motor to
control BTU output.control BTU output.
nn Dip switches to controlDip switches to control
address (must matchaddress (must match
with correspondingwith corresponding
remote).remote).
nn Auto/Man switch toAuto/Man switch to
allow for nonallow for non--remoteremote
operationoperation

Receiver (cont.)Receiver (cont.)
nn Pow ered by four “A A ” Pow ered by four “A A ”
batteries.batteries.
nn Beep codes to indicateBeep codes to indicate
“w orking” or “low “w orking” or “low
battery.”battery.”

TroubleshootingTroubleshooting
nn If the remote doesIf the remote does
not come on whennot come on when
the power button isthe power button is
pressed, replacepressed, replace
the batteries. Ifthe batteries. If
the problemthe problem
persists, call 1persists, call 1--866866--
672672--6040 with your6040 with your
model and serial #model and serial #
handy.handy.

Troubleshooting (cont.)Troubleshooting (cont.)
nn IF the remoteIF the remote
appears to beappears to be
working, but you getworking, but you get
no reaction from theno reaction from the
heater:heater:
1) Check the1) Check the
batteries in thebatteries in the
receiver and replacereceiver and replace
as neededas needed

Troubleshooting (cont.)Troubleshooting (cont.)
2) Check the dip2) Check the dip--switchswitch
settings on the receiver:settings on the receiver:
a.a. Locate the receiver inLocate the receiver in
your heater.your heater.
b.b. Remove the receiver andRemove the receiver and
turn to the side with theturn to the side with the
eight dip switches, labeledeight dip switches, labeled
“address.”“address.”
c.c. C h eck that sw itches “1” C h eck that sw itches “1”
and “3” are up w hile th e and “3” are up w hile th e
rest are downrest are down
d.d. Remove one battery forRemove one battery for
fifteen seconds andfifteen seconds and
replace in order to resetreplace in order to reset
the receiver.the receiver.

Troubleshooting (cont.)Troubleshooting (cont.)
3) Check the code in the3) Check the code in the
remote by:remote by:
a.a. Move the indicator toMove the indicator to
the timer using thethe timer using the
down button.down button.
b.b. Press the minusPress the minus
button ten times orbutton ten times or
until the remote goesuntil the remote goes
blank.blank.
c.c. Press the up or downPress the up or down
key to change thekey to change the
given code to “005”.given code to “005”.
d.d. Press the minus keyPress the minus key
once more.once more.

Troubleshooting (cont.)Troubleshooting (cont.)
nn If everything seemsIf everything seems
to be working andto be working and
yet the unit stillyet the unit still
does not operate,does not operate,
check the wiringcheck the wiring
from the receiver tofrom the receiver to
the valve. Look forthe valve. Look for
any exposed wire,any exposed wire,
breaks, or burns.breaks, or burns.

Troubleshooting (cont.)Troubleshooting (cont.)
If the rem ote is show in g “A U X ” If the rem ote is show in g “A U X ”
a.a. Move the indicator to theMove the indicator to the
timer using the downtimer using the down
buttonbutton
b.b. Press the minus buttonPress the minus button
ten times or until theten times or until the
remote goes blankremote goes blank –– thethe
remote enters setremote enters set--up modeup mode..
c.c. Press the ON/OFF buttonPress the ON/OFF button
five timesfive times -- this removes thethis removes the
“A U X ” Functions“A U X ” Functions..
d.d. Press the minus buttonPress the minus button
once moreonce more –– this returns thethis returns the
remote to normal operationremote to normal operation

Troubleshooting (cont.)Troubleshooting (cont.)
If the remote is in CelsiusIf the remote is in Celsius
a.a. Move the indicator toMove the indicator to
the timer using thethe timer using the
down button.down button.
b.b. Press the minusPress the minus
button ten times orbutton ten times or
until the remote goesuntil the remote goes
blank.blank.
c.c. Press the plus buttonPress the plus button
once.once.
d.d. Press the minusPress the minus
button once morebutton once more