Devine Artis 8A User manual

Artis 8A
Powered speaker

Introduction
Thank you for purchasing this passive Devine Artis speaker. To make sure you use this loudspeaker
as intended and for optimal performance and protection of this speaker, Devine recommends you read
this user manual.
Box contents:
1x Artis 8A Powered loudspeaker
2x monitor stands
1x power cable
Warning!
- This loudspeaker is not suitable for use outside. Keep this speaker away from moisture and rain.
- This loudspeaker is capable of producing sound levels that may cause severe and permanent
hearing damage.
- Make sure the speaker cabinet is installed on a proper surface when used. Place this speaker on the
floor, on a professional speaker stand, on a suitable wall-bracket or on the included monitor feet.
Devine is not responsible for any damage caused by improper installation of this device.
- This speaker is equipped with M8 mounting inserts, but this device is not intended to be rigged with
these points. When doing so, contact a skilled technician for your own safety and only use proper
eyebolts with metric thread. Devine does not take responsibility when this device is not properly
installed.
- To clean this speaker from any dirt or dust and keep it in optimal shape, use a sponge or cloth with a
non-aggressive solution mixed with water. Do not detach the grill to clean the speaker with any wet
cloth, as this may cause permanent damage!
- Always check the voltage settings on the unit and the power supply you want to connect the device
to. If the voltage requirements do not meet, do not connect the device as this may cause serious
damage.
- This unit must be connected to a grounded power supply that meets the voltage requirements of the
device.
- Do not cover the heatsink on the rear of the amplifier module and do not place the speaker directly
against any walls or objects to prevent overheating.

Features and technical data:
- powered speaker
- robust, lightweight construction
- bass-reflex cabinet
- protective grill
- 8 inch woofer
- 1 inch tweeter with dispersion horn
- impedance: 8 Ohm
- 35mm stand adapter with tightening knob
- frequency response: 65 –18.000 Hz (-10 dB)
- sensitivity: 92 dB (+/- 2 dB)
- size: 295 x 255 x 425 mm
- weight: 8 kg
Amplifier module features:
- power: 100W RMS
- peak power: 300W RMS
- amplifier impedance: 4 Ohm
- built-in Clip and Power LED indicators
- built-in USB/SD MP3-player with volume control
- microphone input through 6.35mm jack connector with volume control
- line input: balanced XLR and unbalanced stereo RCA connectors with volume control
- line output: balanced 6.35mm jack connector
- built-in equalizer with bass and treble control
- IEC to Shucko power cable included
NOTE: Illustrations in this manual are only for your reference, illustrations might be slightly
different from the actual product.

Use of the speaker
This speaker is designed to perform in professional environments. Either speech, music, or any other
type of sound can be played trough this speaker.
The Artis A-series are equipped with their own power amplifier, mounted on the rear of the speaker.
This module also houses the internal USB/SD MP3-player and the several connections + volume
controls.
The built-in power amplifier is capable to produce enough power for
the speaker alone, so there is no need for an extra power amplifier and
it is not possible to connect one.
This speaker is also equipped with a lockable 35mm stand adapter,
which makes it possible to place the speaker on a suitable height. This
makes the distribution of high and mid-frequencies easier. See the
image above for details. The lockable screw-knob positions the
speaker firmly on your speaker stand, thus preventing any type of
resonance.
The built-in USB/SD MP3-player supports most USB-thumbdrive and
SD(HC)-cards. However, the results of some models may vary as
many manufacturers have their own standards. The display shows
track information and with the silver buttons you are able to browse through your data. It is not
possible to mix the USB- and SD-slot, only one at a time can be used.
Make sure you connect the right audio sources to the right inputs. The mic input is suitable for most
microphones, but does not supply phantom power, if your microphone requires that. The line input is
suitable for RCA-sources (MP3-players, laptops, smartphones, tablets) and can also be used with an
adapter cable to a 3.5mm jack (not included). A XLR-connector is provided for professional audio
sources, such as DJ or PA mixers, electronic keyboards and so on. The line output is used to connect
a second speaker, such as another Artis 10A. Contact your local dealer when in doubt, as a wrong
connection may cause permanent damage.
Warranty is void when damage to this speaker is caused by improper use. When any damage to this
speaker occurs, please contact your local dealer for help.

Power amplifier module section
The built-in power amplifier module, combined with the built-in MP3-player, connectors and volume
controls, has several options
. A short explanation for each feature is described below:
1. MP3-player with USB and SD slot
10. Power on/off switch
2. MP3 volume control
11. 115/230V switch (pre-defined, do not
switch!)
3. Microphone input (6.35mm jack)
12. IEC power input with fuse holder
4. Microphone volume control
13. Amplifier heatsink
5. Line input (stereo RCA or XLR)
14. Clip LED indicator
6. Line input volume control
15. Power LED indicator
7. Line output (6.35mm jack)
8. Equalizer: Treble control (-12 to +12)
9. Equalizer: Bass control (-12 to +12)

Practical information and tips for optimal use of your speaker system
For optimal performance and a long lifespan of your speaker, please pay attention to the following
when using your Devine speaker:
- This speaker is equipped with a CLIP limiter, which prevents damage to the speaker. This CLIP
limiter will activate at excessive volume levels and a red LED shows when the CLIP limiter is active.
Prevent the activation of the CLIP limiter system and the indicating LED. The CLIP limiter protects the
system from permanent damage, but is only effective at peak signals. Long term exposure causes
distortion and power overload, with possible permanent damage to your speaker system.
- When using an external mixer (such as a PA-mixer or DJ-mixer, make sure your master channel
sends out signals at 0dB maximum. This will provide optimal signal quality and with the volume control
on the speaker you are able to turn up the volume, just before the CLIP limiter LED will slightly flash.
This way you are using the speaker to its full potential with optimal sound quality.
- When using the internal two-band equalizer system and adjusting the sound balance of your
speaker, keep the master volume on a medium, neutral level which is comfortable to your ears.
When you want to add extra bass, try to decrease the Treble-intensity first. When you want to add
more high frequencies (for vocal and speech applications), try to decrease the bass level first.
This way, the EQ system does not have to function as a pre-amplifier, thus providing optimal sound
quality.
- Do not remove the protective cover in front of the voltage-switch. The correct voltage is pre-defined
at 230V AC. When selecting the wrong voltage you may cause permanent damage to the speaker and
its internal components. Only select the 115V AC option when your local power source is capable of
delivering this voltage.
- Do not switch the power on and off frequently as this reduces the lifespan of the speaker and its
internal components. The speaker can be used for a whole day without any cooling-down time, if
sufficient cooling is provided.
- The speaker is equipped with an internal fuse, located directly above the IEC power input section. If
this fuse blows for any reason, only replace it with a fuse that has the same values as the original fuse.
Do not bridge the gap with any electrical wiring or whatsoever as this voids your warranty.
- Severe shocks and impact must be prevented as much as possible. Secure this speaker properly in
place during transport to prevent damage to the housing and the internal components of the speaker.