DEVOLA DVPW1000B User manual

with Wi-Fi Control
Instruction Manual
Please read the manual carefully prior to use.

Safety Instructions
•Read the manual before you use the heater. Keep the manual and ensure it
stays with the heater if you give it to a new owner.
•Before use, check that the heater and all supplied accessories are present and
intact.
•The heater must be installed as per installation instructions. The heater must be
plugged into a socket that meets the following requirements: AC 230V,
frequency 50/60Hz.
•The heater is only suitable for indoor use. Do not use it outdoors!
•Do not leave the heater unattended during use. Keep the heater out of the reach
of children: risk of burns.
•Do not use an external controller with the heater. The heater must not be set to
switch on when it will be unattended.
•Do not use the heater near flammable or explosive materials: risk of fire or
explosion.
•Inserting items into the protective grill of the heater is strictly prohibited: risk of
electric shock.
•Do not touch the metal housing as it will get hot when the heater is in use: risk of
burns. Set aside some time to let the heater cool before you turn it off and store
it.
•Unplug the heater if it is going to be out of use for a long time.
•Prior to each use of the electric heater, make sure it is in a good condition and
intact. Do not plug in or use the heater if the casing, wire, or plug are
damaged.
•The heating element may be damaged if the heater is dropped or hit. Check that
the element is not damaged prior to each use. Do not use the heater if the
element is broken.
•Disconnect the plug from the socket when moving or cleaning the heater. When
disconnecting, first turn off the switch, then unplug the plug. Do not yank the
cable.
•Demolition of the electric heater without authorization is strictly prohibited.
Please look for professional service personnel if the heater is damaged.
•During use, do not let bare skin touch the surface of the appliance: risk of burns.
•Do not share the heater’s socket with other appliances: risk of fire due to
excessive load.
•CAUTION: never cover the heater. Covering the heater risks overheating and
fire.
•The heater must not be located immediately below an electrical socket-outlet.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent, or a similarly qualified person to avoid a hazard.
•Avoid the use of an extension cord as this may overheat and cause a fire risk.
•This heater is not intended for use in bathrooms, laundry areas or similar
locations where there may be moisture. Never place the heater where it may fall

into a bathtub or other water receptacle.
•Do not use the heater in the immediate surroundings of a bath, shower or
swimming pool.
•Children of less than 3 years should be kept away unless continuously
supervised.
•Children aged between 3 and 8 years should only switch the appliance on/off
provided that it has been placed or installed in its intended normal operating
position and they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children aged
between 3 and 8 years should not plug in, clean, or perform maintenance the
appliance.
•This appliance can be used by children aged 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and maintenance should not be carried
out by children without supervision.
•CAUTION: some parts of this product can become very hot and cause burns.
Particular attention must be given where children and vulnerable people are
present.
Installation Instructions
•Before installing, check that all parts are present, and the product is intact.
•If you want to use the electric heater freestanding, please fit with the feet
provided with the heater, following the instructions below. Make sure the heater
is mounted on a level, stable and clean surface.
Freestanding Installation
1. Put the product upside down on a
soft cotton cloth or carpet.
2. Fix the feet to the base of the
heater using the screws provided.
Line up the holes in the base with
the holes in feet, put the screws
through the holes and tighten with
a screwdriver.

Wall Mounted Installation
4 Hook Type Bracket
1. Take out 4 brackets, 6 expansion screws and 6 screws out from the box and fix 2 brackets onto
the wall according to the distances between holes of the bracket, as depicted in the picture
below. Fig. 1
2. Fix 2 brackets onto the bottom of the product, as depicted in the picture below.

3. Holding the sides of the heater, align the brackets and corresponding holes and slide into
position ensuring it is fastened securely.

A. Wi-Fi Connection
B. Working Status-The flame icon is displayed if the heater is in operation
C. Keyboard Lock
D. Timer
E. Comfort Mode
F. Eco Mode
G. Anti-frost
H. Setting
I. Up
J. Down
K. Power Switch/Wi-Fi Setting

Heater Control Panel
•First start by turning the heater on. The heater will start in standby mode, displaying the
Wi-Fi icon and the current room temperature in °C.
•Press the ON/OFF button to initiate heating. When the heater is switched on the
heating icon and the Eco mode icon will illuminate by default. This means that the
heater is operating in Eco mode.
•Use the Up and Down buttons to cycle between the heating modes: Eco ,
Comfort and Anti-frost mode . The mode icons will flash as you cycle through
them. After a few seconds, the mode icon will stop flashing and the heater will heat in that
mode.
•To adjust the set temperature of any of the modes you can press the Setting button ,
wait for the light to flash then use the Up and Down buttons to adjust the
temperature. The temperature range is from 5-50°C.
•To set the timer, press the Setting button , when the Timer icon flashes use the
Up and Down buttons to adjust the time. The timer range is 1-24 hours. The digits
will flash while setting and then the screen will return to heating mode. The Timer icon
will not appear on the display to indicate that a timer has been set and the heater will
continue to operate until the selected time has elapsed.
•To set the child lock function press and hold the Up button. The padlock icon will
appear on the display screen and the control panel will now be locked. To disable the child
lock press and hold the Down button. The padlock icon will disappear to indicate
that the child lock function is now inactive, and all buttons can be used again.
•To switch off the display light whilst the heater is in operation press and hold the for
5 seconds. Press the button again to switch the display light back on.
Eco Mode –In this mode the heater works at half of its maximum capacity. For example, if the
heaters full capacity is 2000W, in eco mode it would operate at 1000W.
Comfort Mode –When the heater is operating in comfort mode it is running at its full capacity,
thus, if it is a 2000W heater it will operate at 2000W.
Anti-frost Mode–This mode is specifically designed to prevent frosting. When the ambient
temperature is below 5℃the product will begin to operate. If the ambient temperature rises greater
than 7℃the product will automatically cease heating.
Remote Control –The remote-control use distance is 2M. All control panel functions are the same
as the remote control.

Connecting to Wi-Fi
1. To connect your heater to the Wi-Fi, the first step is to download the Smart
Life app onto your smartphone or tablet. You can find the app by scanning the
QR code below or searching “Smart Life” in the Google Play or Apple app
store.
2. Download and install the app. Unless you already have a Smart Life account, you
will need to create an account by tapping Register.
The device will automatically determine your country, although you can change this
if necessary. Enter your phone number or email address. If you enter a phone
number,a verification number will be sent toyourphone: enter this number to verify,
then create a password. If you enter your email address, you will need to create a
password.
3. To add your heater to the app, first put the heater in Wi-Fi connection mode. The
heater is in Wi-Fi connection mode when the Wi-Fi icon is flashing. If the
icon is not flashing, go to standby mode and hold down the button for three
seconds.

Once the icon is flashing, go to the app and press Add a Device. Select the
device type(heater)in the Small Home Appliances tab and confirm that the
indicator is flashing. You will then be prompted to enter your Wi-Fi password. This
allowstheapptofindyour heaterusing your Wi-F

4. The app will then display its connecting screen.
NOTE if the heater is failing to connect, press and
hold the button for three further seconds. It will
then switch to its secondary connection mode. The
heater has two connection modes: one where the
icon flashes slowly (once per second) andone
where the icon flashes fast (three times per
second). Most devices will connect on the fast
flashing mode.
5. The heater will beep and display a solid icon when the device is connected.
The app will confirm that the heater has been added. You can now name the
device, share it with family members, or proceed to scheduling your heating.

Using the Smart Life App
You can use the app to control multiple devices. The status of your devices is shown
on the device list:
•Offline (device is turned off at the wall)
•Turned Off (device is in standby mode)
•Turned On (device is in heating mode)
When the heater is online, tap the device name to go to the control interface. Note:
when the heater is offline, you will not be able to control it with the app.
Controlling the Heater
Set Temperature
Temperature
Adjust
Programming
ON / OFF
Current
Temperature
Select Mode

You can change the heater’s current mode by tapping the mode buttons. You can adjust
the mode’s temperature using the + and – buttons when you’re on that mode.
Scheduling your Heating
You can program your heating by creating a schedule of “events”, where the heater
switches on or off. These events can be temporary, like setting a timer, or they can be
recurring, so the heater switches on at the same time every week. You can set an
unlimited number of events, switching the heater on and off across the week.
For every event, you must set a start time. Then, choose whether you want it to
repeat. Select “Only Once” if you just want to set a timer for now. If you want the
event to repeat, select which days you want it to occur. Finally, choose whether you
want the heater to switch on or off. Make sure you confirm your settings at every
stage and press save to keep the event.
Each event will appear in your schedule. You can activate and de-activate events
using the toggle. You can also delete events by swiping left and tapping Delete.
The heater will beep when it begins a new heating event. The heater will heat at
whatever mode it was last set to and you cannot schedule mode changes. Note, if
you change the heater’s setting during an event – i.e. turning it on when it is
scheduled to be off –the heater will remain as it is until the next scheduled event.

Other Features
Scenes
“Scenes” bring all your devices together to respond to environmental conditions.
Triggers of events include the temperature, humidity levels, air quality, sunrise and
sunset, and device behavior. So, for example, you could set your windows to close
every time your heater switches on; or set your lights to switch on, curtains to close
and heater to switch on whenever the sun sets. Only devices connected to the app
can be used in scenes.
Sharing
You can share control of your devices with family members. Go to “device sharing”,
toggle which devices you want to share, and tap Share with New Member. You can then
add their email address or phone number. If they have the app, the device will appear on
their device list. If they don’t have the app, they will be sent a link to download the app.
Note you can only share to numbers and email addresses that are connected to app-
compatible devices: smartphones or tablets.
Voice integration
Smart Life is compatible with both Amazon Echo and Google Home.
FAQs
Find the answer to many troubleshooting problems in the app’s FAQ section.

Technical Data
Type
Voltage
Frequency
Power
Category
DVPW1000B/DVPW1000WH
230V
50/60Hz
1000W
I
DVPW1500B/DVPW1500WH
230V
50/60Hz
1500W
I
DVPW2000B/DVPW2000WH
230V
50/60Hz
2000W
I
ERP LABEL
Model identifier(s):
DVPW1000B/DVPW1000WH/DVPW1500B/DVPW1500WH/DVPW2000B/DVPW2000WH
Item
Symbol
Value
Unit
Item
Unit
Heat output DVPW1000B/DVPW1500B/DVPW2000B
DVPW1000WH/DVPW1500WH/DVPW2
000WH
Type of heat input, for electric storage local
space heaters only (select one)
Nominal heat output
Pnom
1.0/1.5/2.0
kW
manual heat charge control, with
integrated thermostat
No
Minimum heat output
(indicative)
Pmin
0.5/0.75/1.
0
kW
manual heat charge control with room
and/or outdoor temperature feedback
No
Maximum continuous
heat output
Pmax,c
1.0/1.5/2.0
kW
electronic heat charge control with room
and/or outdoor temperature feedback
No
Auxiliary electricity
consumption
fan assisted heat output
No
At nominal heat output
elmax
N/A
kW
Type of heat output/room temperature control
(select one)
At minimum heat output
elmin
N/A
kW
single stage heat output and no room
temperature control
No
In standby mode
elSB
0.00089
kW
Two or more manual stages, no room
temperature control
No
with mechanic thermostat room
temperature control
No
with electronic room temperature control
No
electronic room temperature control plus
day timer
Yes
electronic room temperature control plus
week timer
Yes
Other control options (multiple selections
possible)
room temperature control, with presence
detection
No
room temperature control, with open
window detection
No
with distance control option
Yes
with adaptive start control
No
with working time limitation
No
with black bulb sensor
No
Contact details

Correct Disposal of this product
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was
purchased. They can take this product for environmentally safe recycling.

Warranty
Guarantee and service policy
This product is covered by a standard parts or replacement warranty for a period of 12
months from the date of purchase.
Extend your warranty for 12 months for free by visiting www.devola.co.uk/warranty.
Incorrect installation and failure to follow correct operating instructions are excluded.
Consequential costs such as labour charges or damage to surroundings are expressly
excluded.
Contact Us
If you experience a problem with this product you should first contact us on 0121 250 2180
before taking any further action.
CLAIM YOUR EXCLUSIVE 5% OFF YOUR NEXT ONLINE ORDER
DISCOUNT CODE: DEV5
OFFER VALID FOR 21 DAYS. DON’T MISS OUT!
YOUR DISCOUNT CODE ALSO APPLIES TO OUR SISTER WEBSITES
Visit our websites:
www.devola.co.uk
www.energybulbs.co.uk
www.airconcentre.co.uk
www.ledbulbs.co.uk
This manual suits for next models
5
Table of contents
Other DEVOLA Electric Heater manuals