DeWalt DCS374P2 User manual

Carhartt Workshop Quick Start Guide
DeWalt Portable Band Saw DCS374P2
User Manual
Information pertinent to setup:
This tool is designed and set up for metal cutting only (rebar, galvanized fence posts, conduit,
etc.)
Make sure band saw is clean and clear of obstruction before connecting battery.
Work in a well-ventilated area and wear a respirator and safety glasses when cutting - heat
generated from sawing through certain materials can create hazardous debris and fumes (e.g.
galvanized tubing).
Avoid operating near flammable materials as sparks could be generated.
Always hold tool by insulated gripping handles.
If cutting conduit in place, be sure there are no wires inside the tube as it could cause
electrocution.
Do Not hold or secure pieces being cut with any part of your body. Secure work piece using a
vice or clamps to a safe work area.
Information pertinent to usage:
Stay clear of end pieces that may fall after cutting off.
Make sure to engage trigger lock when not using to prevent the tool from being activated
accidentally.
This tool has does not have the ability to be locked on. Do not alter tool or use additional
devices to make tool remain on.
Always be sure the blade is spinning at full power before engaging your material.
This portable band saw is designed to use .020" (0.5 mm) thick, 1/2" (12.5 mm) wide and 44-
7/8" (1140 mm) long blades. DO NOT USE .025 (.64 mm) thick blades
Blade Speed
oYour DCS374 portable band saw is equipped with variable speed for greater versatility.
Turn the speed wheel (K) to select the desired speed (Fig. 2, below).
oSpeed 1 is the slowest speed; Speed 5 is the fastest.
oWhen cutting copper, brass, bronze, aluminum, cast iron, angle iron, and mild steel, use
a higher speed.
oWhen cutting plastic pipe, tougher steels, chrome steel, tungsten steel, stainless steel,
and other problematic materials, use a low speed.
NOTE: When cutting plastic pipe, higher speeds may melt plastic.

Your band saw is equipped with an adjustable blade tracking mechanism which always assures
proper blade tracking. The back edge of a properly aligned blade will run lightly against one or
both backup rollers in the blade guides. (The pressure between the edge of the blade and the
roller will be very slight and will not damage either the blade or the roller.)
TO ADJUST THE BLADE TRACKING
o1. Use a 1/2" (13 mm) wrench to loosen the adjustment locking nut (G), (shown in Fig. 2
below) by turning it one or two turns counterclockwise.
o2. Use a screwdriver to turn the adjustment screw (H) 1/4 turn. Turning the screw
clockwise will move the blade up toward the blade guide rollers. Turning the screw
counterclockwise will move the blade down away from the rollers.
o3. Adjust so that the back edge of the blade lightly touches the rollers then securely
tighten the adjustment locking nut. (It will be necessary to insert the battery pack and
run the saw to observe the tracking.)
o4. Observe blade tracking between runs and repeat Steps 1–4 as necessary to achieve
proper blade tracking
Information pertinent to Safety: (PPE (Personal Protective Equipment), workspace, etc.)
Familiarize yourself with the tool.
oMake sure you are using the right tool for the job.

oGet to know its safety features, moving parts, and hazards before beginning work.
oInspect tool for damage.
oNever modify, tamper with, or attempt to change or repair tools and parts on your own.
oIf you suspect that a tool may be damaged, malfunctioning or in need of repair, stop
usage immediately, disconnect from power source, and contact the Carhartt Workshop.
Secure a safe workspace.
oMake sure you are working on a clean, dry, level surface.
oClear any debris, trip, slip, fall hazards.
oMake sure your workspace is properly lit.
oCheck that your workspace has proper clearance and is free of obstructions. Including
overhead obstructions such as power lines.
Wear proper PPE
oDo your research and use the proper PPE with the correct safety ratings for the work
you are performing.
oThis includes but is not limited to safety glasses, face shields, earplugs, dust masks,
clothes toed shoes, and proper clothing and footwear.
oNever wear baggy clothes, jewelry, or have longhair down and unsecured.
Handle Tools with care
oNever carry power tools by their cords
oNever leave tools unattended.
oDisconnect from power and secure tools when they are not in use.
oDo not carry sharp or pointed tools in your pockets.
Take your time
oDo not rush or force materials through tools.
oPay attention to your work and surroundings.