Dewenwils HOSL03E User manual

SKU: HOSL03E
V20627
Please pay attention to the warning signs
Read the instructions with caution before operating
and keep it properly

Important safety information to reduce risk of fire injury.
1. Do not install within 10 feet (3 m) of a pool, spa or fountain.
2. There are no serviceable parts inside the power supply unit. DO NOT
DISASSEMBLE.
3. Do not repair or tamper with cord or plug.
4. Do not submerge transformer in water.
5. Do not mount the transformer onto combustible material.
6. Do not connect two or more transformers in parallel.
7. Do not use the transformer with a dimmer switch.
8. Plug the power supply unit directly into a GFCI wet location outlet.
9. For use with low voltage outdoor landscape lighting system only.
10. The maximum output of this transformer is 120 watts. Do not overload
the transformer. Be sure that the total cumulative wattage of all 12 volt
fixtures connected to the transformer is equal to or less than 120 watts.
SAFETY INSTRUCTIONS
The 120 Watt transformer has 120 watt circuits which will power up to 120
watts of light. To make sure the maximum number of fixtures can be safely
connected to this transformer, add up the individual wattage of all the
fixtures. The total wattage of your fixtures must not exceed output capacity
of the 120 Watt transformer.
Being careful when splitting it.
NOT to expose the copper cable.
Remove the landscape cable
insulation 1/2 inch from both
cables and twist ends.
CALCULATE LIGHTING CAPACITY
1. Preparing the Cable
INSTALLATION
CAUTION: This landscape light system must be installed in accordance
with all local codes and ordinances. If you are experiencing problems,
contact a qualified electrician.

Lay the transformer on a flat, stable surface and use screwdriver to connect
the stripped ends of the cable under the terminal clamping plate.
Tips: Thread your cable through the white plastic loop to reduce its gravity.
As the following image shows, there are 3 group wiring ports(COM/12V/
14V for each group), you can choose any group of them to connect your
cable. For each group, there are 2 terminal output ends- 12V/14V, select
the appropriate terminal according to your lamp voltage.
2.Connecting the cable to the Transformer
Lay your fixtures (not included) to your desired location. Be sure they do not
exceed the 120-watt rating of the transformer. Coil the rest of the cable after
the last fixture. Transformer Cable Fixtures.
3.Placing Your Fixtures and Routing the cable
Note: Gently pull on the landscape
cable to verify if the connection is strong.
Use the cable connectors to attach your fixtures with the cable. Plug the
transformer in the GFCI outlet and enter the ON mode. Then the lamps
will light up.
4.Attaching Your Fixtures

Use the screw to mount the transformer directly on a wall. 12 inch to 48
inch (0.3 m to 1.2 m) high from the ground would be suggested.12in. to
48in. (0.3m to 1.2m)
5.Mounting the Transformer

Tips: After completing installation, please remove the cap from the
photocell sensor for exposing it to light.

The currently selected output port of the transformer has no output voltage,
and the load lamps do not light up.
Figure 1: OFF MODE
The currently selected output port of the transformer will maintain the output
through the day, and the load lamps will be always on.
Figure 2: ON MODE
In this mode, it will also take 0-30s for the transformer to detect the external
environment firstly. If it is night, the currently selected output port of the
transformer will start output later and the load lamps will light. Then they will
turn off automatically when the the countdown is over. If it is during the day,
the currently selected output port of the transformer will have no output and
the load lamps will not light.
Note: When the system starts to count down, if the surrounding light shines
on the sensor for more than 30s, the countdown will end, the currently
selected output port of the transformer will stop output, and the load lamps
will go out.
Figure 4 & Figure 5: COUNTDOWN MODE
In this mode, it will take 0 ~30s for the transformer to detect the external
environment firstly. If it is night, the currently selected output port of the
transformer will start output later, then the load lamps will light on
automatically and off at dawn. If it is during the day, the currently selected
output port of the transformer will have no output and the load lamps will
not light.
Note: If the light emitted by the load lamps shines on the sensor at night,
it may cause the transformer to continuously switch on/off, and the load
lamps flash continuously, with a flash interval of 30s.
Figure 3: AUTO MODE

1 x Low Voltage Transformer
2 x Screws
2 x Wall Anchors
1 x Instruction Manual
PACKING LIST
- Model: TD-120-12WF-1
- Input Voltage: 120VAC, 60Hz
- Output: 12VAC/14 VAC
- Max Power Rating: 120W
- Photo Sensor Cable Length: 6 ft
SPECIFICATIONS
One Year Limited Warranty
Supported by our professional R&D team and QC team, we provide One
Year Warranty for materials and workmanship from the purchase date.
Please note that the warranty does not cover damage caused by personal
misuse or improper installation.
Please attatch your Order ID and Name so that our dedicated customer
service team can help you better.