dewert okin RF396E User manual

Issue Department
：
Bedding
Division
Date：2022-03-25
User manual
Author
：
Edition
：
1.0
Page 1 of 7
User manual of RF396E
Figure 1 button ofremote
Child lock
Lumbar up
M1 position
Head up
Lumbar down
Head down
Massage model
Flat
Zero position
M2 position
Foot massage
TV position
Bed lamp
Head massage
Antisnore
Foot up
Doot down
Massage frequent
Massage frequent
1/ 7

Issue Department
：
Bedding
Division
Date：2022-03-25
User manual
Author
：
Edition
：
1.0
Page 2 of 7
Item
1.1 Child Lock 1
Click the Child Lock button for 3 second to lock or unlock the remote.
1.2 Bed lamp 2
Click the bed lamp button to open or shut the light under the bed.
1.3 Antisnore 3
Click the Antisnore button, the bed moves to Antisnore position, press and hold Antisnore
button for 5s, until backlight flashes, the control set the current position as Antisnore position
1.4 TV 4
Click the TV button, the bed moves to TV position, press and hold TV button for 5s, until
backlight flashes, the control set the current position as TV position.
1.5 LUMBAR UP 5
Press and hold LUMBAR UP button, Lumbar actuator moves out, stop when released.
1.6 LUMBAR DOWN 6
Press and hold LUMBAR DOWN button, Lumbar actuator moves in, stop when released.
2/ 7

Issue Department
：
Bedding
Division
Date：2022-03-25
User manual
Author
：
Edition
：
1.0
Page 3 of 7
1.7 M1 7
Click the M1 button, the bed moves to M1 position, press and hold M1 button for 5s until
backlight flashes, the control set the current position as M1 position
1.8 M2 8
Click the M2 button, the bed moves to M2 position, press and hold M2 button for 5s until
backlight flashes, the control set the current position as M2 position
1.9 HEAD UP 9
Press and hold HEAD UP button,head actuator moves out, stop when released.
1.10 HEAD DOWN 10
Press and hold HEAD DOWN button, head actuator moves in, stop when released.
1.11 FOOT UP 11
Press and hold FOOT UP button,foot actuator moves out, stop when released.
1.12 FOOT DOWN 12
Press and hold FOOT DOWN button, foot actuator moves in, stop when released.
1.13 ZG 13
Click the ZG button, the bed moves to zeroG position, press and hold zeroG button for 5s,
3/ 7

Issue Department
：
Bedding
Division
Date：2022-03-25
User manual
Author
：
Edition
：
1.0
Page 4 of 7
until backlight flashes, the control set the current position as zeroG position
1.14 HEAD MASSAGE 14
Click the HEAD MASSAGE button, head massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3；
1.15 MASSAGE model 15
Click the MASSAGE MODEL button to change the massage model.
1.16 FOOT MASSAGE 16
Click the FOOT MASSAGE button, foot massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3
1.17 FLAT 17
Click the FLAT button, the bed goes flat.
1.18
MASSAGE FREQUENT 28Hz
Click the 28Hz button to set the massage frequent 28Hz.
1.19 MASSAGE FREQUENT 40Hz
Click the 28Hz button to set the massage frequent 40Hz.
4/ 7

Issue Department：Bedding
Division Date：2022-03-25
User manual Author：
Edition：1.0
Page 5of 7
1.20 S20
The two remote controls are synchronized wirelessly.
5/ 7
S21
S20
1.21 S21
Click the S21 button, the remote control will be paired with the control box.

Issue Department
：
Bedding
Division
Date：2022-03-25
User manual
Author
：
Edition
：
1.0
Page 6of 7
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
6/ 7
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirment. The device can
be used in portable exposure condition without restriction.

Issue Department
：
Bedding
Division
Date：2022-03-25
User manual
Author
：
Edition
：
1.0
Page 7of 7
(2) l'utilisateur del'appareil doit accepter tout brouillage adioélectrique subi, même si
le brouillage est susceptible d'en compromettre lefonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment.The device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac
un autre environnement.ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition
aux rf.
7/ 7
Canada, Industry Canada (IC) Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio
exempts de licence.L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et