Dexter Laundry T-30X2 User manual

8514-254-001 rev. D
COMMERCIALDRYER OriginalInstructions
MODELT-30X2VENDED ForGB&IE
C-SERIES CONTROL, ELECTRICALLY HEATED
OPERATOR’S MANUAL
INSTALLATION & OPERATION INSTRUCTIONS
The dryer will operate correctly in ambient temperatures of 5°C to 45°C, in relative humidity up to
50% at 40°C and above 50% when below 40°C, and at altitudes up to 1000m above sea level, must
be transported and stored from -40°C to 140°C, and has been packaged to prevent damage from
humidity, vibration, and shock. Take measures to avoid harmful effects of occasional condensation.
Post the following “For Your Safety” cautions in a prominent location:
FOR YOUR SAFETY
Do not store or use petrol or other flammable vapours and liquids or dry cleaning
solvents in the vicinity of this or any other appliance.
FOR YOUR SAFETY
THIS MACHINE IS FOR DRYING ONLY FABRICS WASHED IN WATER.To avoid
possibility of fire, including spontaneous combustion, do not dry oiled floor
mops, items containing foam rubber or similarly textured rubberlike materials or
any material on which you have used a cleaning solvent or which contains
flammable liquids or solids (such as petrol, kerosene, waxes, etc.) Fabric
softeners, or similar products, should be used per the fabric softener
instructions. Remove all objects from pockets such as lighters and matches.
WARNING – Risk of Fire
Clothes dryer installation must be performed by a qualified installer.
Install the clothes dryer according to the manufacturer’s instructions and local codes.
Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)
duct is installed, use duct that has been investigated and found acceptable for use with clothes
dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These
conditions will obstruct clothes dryer airflow and increase the risk of fire.
To reduce the risk of severe injury or death, follow all installation instructions.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision. Children of less than 3 years
should be kept away unless continuously supervised.
It is important that you read this Manual and retain it for future reference. For service or
replacement parts, contact the distributor in your area or the manufacturer:
Dexter Laundry, Inc.
2211 West Grimes Avenue
Fairfield, Iowa 52556, USA

8514-254-001 rev. D page 2
TABLE OF CONTENTS
DRYER DIMENSIONS (Figure 1).............................................................................5
UNCRATING.........................................................................................................6
DRYER INSTALLATION (Figure 2).......................................................................... 7
DRYER EXHAUST SYSTEM (Figure 3)..................................................................... 10
DRYER SHUTDOWN..............................................................................................10
DESCRIPTION OF DRYER CONTROL...................................................................... 11
OPERATING INSTRUCTIONS................................................................................. 12
PROGRAMMING THE DRYER CONTROL……............................................................ 12
SERVICING AND TROUBLESHOOTING................................................................... 25
PREVENTATIVE MAINTENANCE............................................................................. 26
WARNINGS ABOUT USE AND OPERATION
Caution! There are sharp edges on various sheet metal parts
internal to the enclosure. Use safety consciousness when placing or
moving your hands while working in the interior of this equipment.
Meaning: Do Not Enter This
Equipment (or Space).
Meaning: Do Not Step, Stand, or Sit
on This Equipment.
Meaning: Do Not Operate with
Guards or Covers Removed.
Meaning: High Voltage. Disconnect
power before servicing.
Meanin
g
: Lock Out and Ta
g
Out
before servicing.
Meaning: Burn Hazard. Do Not Touch
Heater Housing or Heating Elements.
Allow these parts to cool before servicing.
Meaning: Do Not Dry Items
Containing Explosive Material.
Meaning: Do Not Dry Items
Containing Flammable Material.
Meaning: Read Operators
Manual.
Meaning: Center of Gravity.
Meaning: Left Point for Forklift
or Hand Pallet Truck or Jack.
Meaning: Right Point for Forklift or
Hand Pallet Truck or Jack.
DO NOT MODIFY THIS APPLIANCE. KEEP SHIELDS, GUARDS, AND COVERS IN
PLACE. These safety devices are provided to protect everyone from injury.
It is ABSOLUTELY ESSENTIAL that the dryer be connected to a good earth connection.
This is not only for personal safety, but is necessary for proper operation of the controller.
Failure to do so will void the warranty of the controller.
THIS DRYER IS EQUIPPED WITH A MANUALLY RESETTABLE OVER-TEMPERATURE
THERMOSTAT located on the side of the exhaust duct above each motor. If the dryer cease
to operate, reset the thermostat by rotating the lever bracket clockwise. If the thermostat
continues to trip, the dryer must be inspected by a qualified service person.
CHECK THIS THERMOSTAT WHEN INSTALLING DRYER to assure it is not tripped.
Impacts, such as rough handling in shipment, may trip the thermostat.

8514-254-001 rev. D page 3
WARNINGS ABOUT USE AND OPERATION continued
WARNING: Do not stop dryer before end of cycle time unless all items are quickly removed
and spread out to dissipate heat.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE while in operation.
THIS APPLIANCE SHALL NOT BE USED TO DRY OFF CLOTHES CONTAINING
SOLVENTS OR DRY-CLEANING FLUIDS.
Misuse of Dryer
Do not use this Equipment for any purpose not described in this Manual.
Do not operate this equipment without all guards and covers in place.
Do not operate this dryer from any power source not matching the
operational requirements on the back of the dryer.
Do not place your body inside the dryer cylinder or allow others to do so.
Death or serious injury can result from this!
Other Examples May Be Applicable
Caution – Replace Fuses With Same Type and Rating
Fuse No. Voltage Amperage SC I/R Type Size
F1 250V 2.5A 100A@250VAC F ¼ x 1¼ in. (6.35 x 31.75 mm)

8514-254-001 rev. D page 4
SPECIFICATIONS
13.6 kg (30 lb.) Commercial Stack Dryer: T-30x2 - DC30X2E_-79CC_X
Cabinet Height 76 1/4 in. 1937 mm.
(Assumes minimum leveling leg adjustment)
Cabinet Width 31 1/2 in. 800 mm.
Overall Depth 49 3/4 in. 1264 mm.
Floor to Bottom of Door- Bottom Dryer 7 3/4 in. 197 mm.
Floor to Bottom of Door- Top Dryer 45 1/2 in. 1156 mm.
Door Opening 22 5/8 in. 575 mm.
Dry Wt. Capacity 30 x 2 lbs. 13.6 x 2 kg.
Cylinder Diameter 30 in. 762 mm.
Cylinder Depth 27 1/2 in. 699 mm.
Cylinder Volume 11.25 cu. ft. 319 liters
Lint Screen Area 453 sq. in. 2923 sq. cm.
Electric Heat Input (per dryer) 24 kW
Exhaust Size 8 in. 203 mm.
Make-up Air 1.5 sq. ft. 1394 cm².
Example: 1.5 sq. ft = 1 ft. long X 1.5 ft. wide
Motor Size 1/2 H.P. .373 kW
Airflow 500 CFM 14.2 m³/min
Electrical Specifications - 230/50/1
Voltage/Hz/Phase 400V/50Hz/3Phase
Running Amps 45
Circuit Protection Amps 50
WireSize #6gauge(13.3mm^2)
Electrical Service L1 + L2 + L3 + N + PE
Shipping Weight 750 lbs. 340 kg.
Net Weight 699 lbs. 317 kg.
Clearance Behind Machines (min.) 18 in. 457 mm.

8514-254-001 rev. D page 5
MAX
MIN

8514-254-001 rev. D page 6
INSTALLATION INSTRUCTIONS
Note: A forklift, or a hand pallet truck or jack, must lift the dryer and only from the
front or rear of the dryer with the dryer bolted to the pallet and supported the full
length of the dryer.
UNCRATING AND PLACING DRYER
Tools Required: 19 mm (3/4 in.) hex socket & ratchet driver, wood block 100 mm (4 in.) or 125
mm (5 in.) thick, a knife, and groove joint pliers, which will open to 35 mm (1 3/8 in.).
1. Remove and discard the packaging.
2. The crate base is attached to the dryer by (4) cap screws driven upward from below the
crate base. Remove the crate base from the dryer, by tipping the dryer sidewise and place
the block under the crate base rail in the center of the dryer. Using the ratchet and the 19
mm (3/4 in.) hex socket, remove the (2) crating bolts from the side, which is raised, and
save for future moving of the dryer. Remove the block from under the crate base. Repeat
for the other side.
3. With a walking motion, move the dryer completely off the crate base. Save the crate base
for future moving of the dryer.
4. Slide the unit into the position where it will be installed. Adjust the leveling legs, using the
groove joint pliers, to level and align the dryer with adjacent units.
Note: If the dryer is ever moved again, the dryer should be re-mounted on its crate base and
its crating bolts re-inserted and tightened, in the reverse order as above.
Dryer Model Mass
DC30X2E_-79 340 kg
DRYER INSTALLATION
1. CODE CONFORMITY: All commercial dryer installations must conform to the local and the
national codes for the location of the installation.
The appliance must not be installed behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the
tumble dryer door is restricted.
2. INSTALLATION CLEARANCES: This unit may be installed at the following alcove clearances.
I. Left Side 0 in.
II. Right Side 0 in.
III.Back 457 mm (18 in.) (Certified for 150 mm (6 in.) clearance; however, 457
mm (18 in.) clearance is necessary behind the belt guards to allow for
servicing and maintenance.)
IV. Front 1220 mm (48 in.) (To allow use of dryer.)
V. Top Refer to Figure 2 labeled “Vertical Clearance Dimensions”.
AB. Certification allows 0 in. clearance at the top, 100 mm (4 in.) back
from the front. However, a 6 mm (1/4 in.) clearance should be allowed in
case the dryer needs moving.
C. A 254 mm (10 in.) clearance is required from top at all other points.
VI. Floor This unit may be installed upon a combustible floor.
Do not obstruct the flow of combustion and ventilation air.
Maintain minimum of 25 mm (1 in.) clearance between duct and combustible material.

8514-254-001 rev. D page 7
Refer to the installation label attached to the Belt Guard on the rear of the dryer for other
installation information and start-up instructions.
3. MAKE-UP AIR. Adequate make-up air (17 m3/min./DRUM (600 CFM), 34 m3/min./DRYER
(1200 CFM)) must be supplied to replace air exhausted by dryers on all types of installations.
Provide a minimum of 0.14 m2(1.5 ft.2) make-up air opening to the outside for each dryer.
This is a net requirement of effective area. Screens, grills or louvers, which will restrict the
flow of air, must be considered. Consult the supplier to determine the free area equivalent for
the grill being used.
The source of make-up air should be located sufficiently away from the dryers to allow an
even airflow to the air intakes of all dryers. Multiple openings should be provided.
The operation of this appliance may affect the operation of gas appliances, which take their air
for safe combustion from the same room. Adequate ventilation must be provided to avoid
back flow of gasses from other appliances in the same room. All gas appliances should be
tested with the Dexter dryer in operation and all the windows and doors closed. If in doubt,
consult the appliance manufacturer(s).
4. ELECTRICAL REQUIREMENTS.
The electrical installation must be performed by a qualified electrical technician.
The electrical power requirements necessary to operate the unit satisfactorily are listed on the
serial plate located on the back panel of each dryer. The electrical connection should be made
at the terminal blocks in the two control boxes on the rear of the unit using conductors rated
at 75°C (167°F) and a wire size adequate to handle the amperage and voltage listed on the
serial plate (see the table on the next page for recommended minimum sizes). It is absolutely
necessary that the dryer be connected to a known earth (No. 8 AWG copper conductor
recommended). Knockouts are provided for the connection of 1-inch (25 mm) conduit for the
power supply conductors and 3/8-inch (10 mm) conduit for the external earthing conductor.
It is absolutely necessary that the dryer be connected to a known earth connection. The earth
connection resistance should be checked prior to operation. Introduction of supply wiring
must not increase the Ingress Protection (IP) rating.
TOP OF DRYER
SIDE OF DRYER
FRONT
OF
DRYER
FIGURE
2
- Vertical Clearance Dimensions

8514-254-001 rev. D page 8
HEATING
ELEMENT SIZE
(kW)
SUPPLY
VOLTAGE
(PHASE / V.)
MINIMUM DUAL ELEMENT TIME
DELAY FUSE SIZE AT FUSED
DISCONNECT (A.)
MINIMUM WIRE SIZE FROM FUSED
DISCONNECT TO DRYER TERMINAL
BLOCK (75OC COPPER WIRE)
24 3 / 400 50 # 6 (13.3 mm^2)
The installation must meet the electrical requirements of the country, state, and locality of the
installation. Individual circuit breakers for each dryer are required. The installer must provide
a disconnect switch which will interrupt all lines. It may be a local or national requirement to
provide an electrical interruption switch visible and accessible from the room in which the
dryer is installed. The wiring diagram is located in the control box on the back of the dryer.
For destination countries where CE requirements must be met, individual 400V supply
disconnecting devices for each dryer are required and must be one of the following types:
a. switch-disconnector with fuses per IEC 60947-3 utilization category AC-23B;
b. disconnector with fuses per IEC 60947-3 having an auxiliary contact that in all cases causes
switching devices to break the load circuit before the opening of the main contacts of the
disconnector;
c. a circuit-breaker suitable for isolation per IEC 60947-2;
d. any other switching device in accordance with an IEC product standard for that device and
which meets the isolation requirements of IEC 60947-1 as well as a utilization category
defined in the product standard as appropriate for on-load switching of motors or other
inductive loads;
The supply disconnecting devices must
a. provide a means allowing the supply disconnecting devices to be locked in the OFF position;
b. be mounted 0.7 m to 1.7 m above the floor, within 2 m from the dryer, and within 8 m
from the operator position;
c. have a red actuator to indicate that it serves a dual Emergency Stop function;
d. be rated for branch circuit operation;
e. be approved for use in the country where installed;
CONTROL TRANSFORMER CONNECTIONS Adjustment for different voltages of supply mains.
IMPORTANT: TRANSIENT VOLTAGE SURGE SUPPRESSORS
Like most electrical equipment your new machine can be damaged or have its life shortened
by voltage surges due to lightning strikes which are not covered by factory warranty. Local
power distribution problems also can be detrimental to the life of electrical components. We
recommend the installation of transient voltage surge suppressors for your new equipment.

8514-254-001 rev. D page 9
These devices may be placed at the power supply panel for the complete installation and don’t
require an individual device for each machine.
These surge protectors help to protect equipment from large spikes and also from small
ongoing spikes in the power that occur on a day to day basis. These smaller surges can
shorten overall life of electrical components of all types and cause their failure at a later date.
Although they can’t protect against all events, these protective devices have a good
reputation for significantly lengthening the useful life of electronic components. Electronic
components are helped to have a longer useful life when they are supplied with the clean
stable electrical power they like.
6. EXHAUST INSTALLATION. (Refer to Figure 3) Exhausting of the dryer(s) should be
planned and constructed so that no air restrictions occur. Any restriction due to pipe size or
type of installation can cause slow drying time, excessive heat, and lint in the room.
From an operational standpoint, incorrect or inadequate exhausting can cause a cycling of the
high limit thermostat, which shuts off the heating elements and results in inefficient drying.
The exhaust duct connection near the top of the dryer will accept a 203 mm (8 in.) round
duct. Individual exhausting of the dryers is recommended. All heat, moisture, and lint should
be exhausted outside by attaching a pipe of the proper diameter to the dryer adapter collar
and extending it out through an outside wall. This pipe must be very smooth on the inside, as
rough surfaces tend to collect lint, which will eventually clog the duct and prevent the dryer
from exhausting properly. All elbows must be smooth on the inside. All joints must be made
so the exhaust end of one pipe is inside the next one downstream. The addition of an
exhaust pipe tends to reduce the amount of air the blower can exhaust. This does not affect
the dryer operation if held within practical limits. For the most efficient operation, it is
recommended that no more than 4.27 m (14 ft.) of straight 203 mm (8 in.) diameter pipe with
two right angle elbows be used for each cylinder. The design of the vent system shall be such
that any condensate formed when operating the dryer from cold shall either be retained and
re-evaporated or discharged.
Maintain a minimum of 25 mm (1 in.) clearance between duct and combustible material.
If the exhaust pipe passes through a wall, a metal sleeve of slightly larger diameter should be
set in the wall and the exhaust pipe passed through this sleeve. This practice is required by
some local codes and is recommended in all cases to protect the wall. This type of installation
should have a means provided to prevent rain and high winds from entering the exhaust when
the dryer is not in use. A hood with a hinged damper can be used for this purpose. Another
method would be to point the outlet end of the pipe downward to prevent entrance of wind
and rain. In either case, the outlet should be kept clear, by at least 610 mm (24 in.), of any
objects, which would cause air restriction.
Never install a protective screen over the exhaust outlet.
When exhausting a dryer straight up through a roof, the overall length of the duct has the
same limits as exhausting through a wall. A rain cap must be placed on top of the exhaust
and must be of such a type as to be free from clogging. The type using a cone shaped “roof”
over the pipe is suitable for this application.
Exhausting the dryer into a chimney or under a building is not permitted. The exhaust air
should not be vented into a wall, a ceiling, or a concealed space of building. In these cases,
there is a danger of lint buildup, which can be highly combustible.

8514-254-001 rev. D page 10
Installation of several dryers, where a main discharge duct is necessary, will need the
following considerations for installation (see Figure 3). Individual 203 mm (8 in.) exhaust
ducts from each dryer should enter the main discharge duct at a 45-degree angle in the
direction of discharge airflow.
NOTE: Never install the individual 203 mm (8 in.) ducts at a right angle into the main
discharge duct. The individual ducts from the dryers can enter at the sides or bottom of the
main discharge duct. Figure 3 indicates the various round main duct diameters to use with
the individual dryer ducts. The main duct can be rectangular or round, provided adequate
airflow is maintained. For each individual dryer, the total exhausting (main discharge duct
plus duct outlet from the dryer) should not exceed the equivalent of 4.27 m (14 ft.) and two
elbows. The diameter of the main discharge duct at the last dryer must be maintained to
exhaust end.
NOTE: A small diameter duct will restrict airflow; a large diameter duct will reduce air velocity
- both contributing to lint buildup. An inspection door should be provided for periodic clean
out of the main duct.
NOTE: Exhaust air must not be discharged into a flue which is used for exhausting fumes from
appliances burning gas or other fuels.
Caution - A clothes dryer produces combustible lint and should be exhausted
outdoors. The area around the clothes dryer should be kept free of lint.
NOTE: The A-weighted emission sound pressure level does not exceed 70dB(A). The operator
does not need hearing protection.
NOTE: The dryer does not emit hazardous radiation.
WARNING: To avoid potential risks of spontaneous combustion of a load, remove the
load quickly after the completion of the cycle or in case of failure of power supply.
DANGER: Do not dry loads which may create an explosive atmosphere in the dryer.
DRYER SHUTDOWN
To render the dryer inoperative, disconnect electrical supply to the dryer.
DIAMETER TO INCREASE AS SHOWN
WALL
INSTALL NO
SCREEN OR
COVER
EXHAUST AIR
(SEE INSTRUCTIONS)
DRYER DUCTS
MUST ENTER AT
A 45° ANGLE
INCHES
(MM)
INSPECTION
COVER
FIGURE 3- Dryer Exhausting Using A Main Discharge Duct.

8514-254-001 rev. D page 11
DESCRIPTION OF DRYER CONTROL
Both dryers are operated by the controller at the left midpoint of the dryer. The controller is two-
in-one with the upper display and lights dedicated to the upper dryer and lower display and lights
dedicated to the lower dryer.
1. When money has been deposited, the control will prompt the user to choose a drying
temperature and press the “start” button. Time is not added until this occurs for either the
upper or lower dryer. If no purchased time is available on the control, the vend price is
displayed.
The drying program (temperature) selected by the user is indicated by the red lights at the top and
bottom. When the dryer is in use, the drying temperature may be displayed by simultaneously
pressing the “start” button and the button of the temperature selected.
Cool-down time (owner programmable) is always part of the cycle time to prevent damage from
heat and is purchased by the customer. For example, if cool-down time is 2 minutes, the last two
minutes of the cycle will have no heat.

8514-254-001 rev. D page 12
OPERATING INSTRUCTIONS
STARTING THE DRYER
1. Load clothes into either the upper or lower dryer (or both). Close the door(s) completely.
2. Deposit coins equal to or greater than the displayed vend price. The control will prompt the
user to choose a drying temperature. Time is not added until this occurs for either the upper or
lower dryer.
3. Select drying temperature by pressing the appropriate button for the dryer to be used. This
will turn on the red light showing the selected temperature.
4. Press “start” button to start dryer. This will display the drying time purchased.
RUNNING THE DRYER
-Opening the door will stop the dryer. The dryer will restart, if time has not expired, upon
closing the door and pressing the “start” button.
-Selected temperature may be changed at any time (unless Temperature Pricing
feature is activated).
-Running time may be extended by depositing coins and pressing the “start” button for the
correct dryer. Unless time has expired, the controller will accept coins whether or not the
original vend price is equaled.
If time has run out, the dryer must be restarted as if it was at the beginning of drying the load,
which requires meeting or exceeding the vend price.
PROGRAMMING THE DRYER CONTROL
The dryer control can be programmed to prompt the user for alternate vend prices, change
dryer cycle times, temperatures and many other options. This can be accomplished in two
ways:
1. Manual programming utilizing the “Start”, “High”, “Medium” and “Low” buttons for the
bottom dryer.
2. USB download of a customizable User File. For instructions on using the USB download
feature, please contact your local Dexter distributor or visit DexterLive.com.
MANUAL PROGRAMMING:
The dryer must be in idle mode for the manual programming menus to be accessed. Idle
mode is when the dryer is not actively running a drying cycle and the vend price is displayed
on the screen (for both upper and lower dryers).
To enter the manual programming mode, the control tray on the dryer must be unlocked and
pulled out to reveal the programming button. The programming button is then pressed for 1
second. The control should display “DRYER PROGRAMMING”.

8514-254-001 rev. D page 13
See the figure below for the location of the programming button on the control tray.
When manual programming mode is entered, the “Start”, “High”, “Medium” and “Low” buttons
for the lower dryer perform alternate functions. Please note that the changes made using the
lower dryer buttons affect both upper and lower dryers.
Button Name Alternate Function in Programming Mode
Start Becomes the action to accept the displayed option or
the “Enter” key
High Becomes the action to move UP through displayed
options (Press & hold for accelerated scrolling)
Medium Becomes the action to move DOWN through displayed
options (Press & hold for accelerated scrolling)
Low Becomes the action to move back a step (1 press) or
EXIT from programming mode (press for 3 seconds)

8514-254-001 rev. D page 14
These alternate functions allow the user to move through a menu of options to choose various
programmable settings. The figure below shows the top level menu. Choosing an option from
the top level menu will then display the next level of options (the sub menu).
Quick Test Option:
When the Quick Test Option is chosen, the dryer will begin a shortened dry cycle without the
displayed vend price being met. The purpose of this shortened cycle is to test all major
components for proper operation.
Error Codes should all function normally during this test. The display will show customer
prompts in a similar way to a normal dry cycle.
Continuous Test Option:
Similar to the Quick Test, when the Continuous Test Option is chosen, the dryer will begin a
dry cycle without the displayed vend price being met. However, in this case, it will be a
continuously-running cycle. It will not time out after any designated amount of time.
CAUTION: This option is meant for factory use only. Do not operate the dryer with this cycle
active without factory authorization.
Error Code Historical Log:
The last fifteen occurring error codes will be stored in the control with a time and date stamp.
The purpose of this option is only to observe the history of these code occurrences (no
changes can be made).
The time is based off the Real Time Clock, but potentially shifted by the user’s manual
programming changes (Shift Hours option) and/or network time override. As additional error
codes occur, the oldest of the fifteen logged codes is cleared from memory.

8514-254-001 rev. D page 15
Prices Option:
This option allows the user to set values for coin acceptor inputs, vend price & time and
extend dry price & time. It also allows the user to return the values to factory defaults. After
changing prices using the “Up” or “Down” buttons, the “Enter” button must be pressed again
for the control to store the changes that have been made. Note that, in general, time values
are set in 1 minute increments. This can be changed to 30 second increments, by changing
the “Display Time” to “MIN+SEC” (refer to the “Settings” section”).
1. “RIGHT COIN” and “LEFT COIN” are the two possible inputs from coin acceptors.
2. “PRICE SET VEND” is the actual Base Vend Price (or Vend Price A) that is shown on the
control display. The value can be increased or reduced even down to “0”. In this case,
the displays will prompt “FREE” and the cycle will start as soon is the “Start’ button is
pressed (without any vend price being met).
3. “TIME SET VEND” is the cycle time that the customer has available once they’ve met
the Base Vend Price.
4. “FREE SET TIME” is the cycle time that the customer has available if the Base Vend
Price is set to “FREE”.
5. “EXTEND DRY” sets the price and time for additional drying time that becomes available
after the customer has already met the Base Vend Price.
To reset either the coin acceptor inputs or the vend price to factory default, press “Enter”
when the “DEFAULT” prompt is shown. Press “Enter” again when the “RESET” prompt is
shown to confirm the action.
Example- A store owner has programmed the control for the following values:
Base Vend Price $1.00
Base Vend Time 30 minutes
Extend Dry Price $.25
Extend Dry Time 8 minutes
In this case, the customer adds 4 quarters to satisfy the $1.00 Vend Price. The display
shows 30 minutes of drying time. At this point, if an additional quarter is added, the
customer display shows an additional 8 minutes of drying time (38 minutes total) as per
the Extend Dry Price & Time.
The customer starts the drying cycle and at 25 minutes into the cycle (13 minutes
displayed), they add an additional quarter. The controller adds 8 minutes to the
displayed time again (21 minutes total) as per the Extend Dry Price & Time.
“AFTER CYCLE” allows the user to choose whether a customer is allowed to add “EXTEND
DRY” time for up to 30 seconds after the dryer door is opened after a completed cycle.

8514-254-001 rev. D page 16
The figure below shows the sub menu options for Prices:

8514-254-001 rev. D page 17
Cycles Option:
This option allows the user to set temperature and cooldown information for the drying cycle.
It also allows the user to return the values to factory defaults.
1. “TEMP SETTINGS” allows the user to make adjustments, within a designated range, to
the cycling temperature for each of the “Low”, “Medium” and “High” customer choices.
2. In addition, on the “Low” setting, the user can reduce the cycling temperature below
110 degrees F. In this case, when the customer chooses the “Low” setting, the dryer
will not turn on the heat relay. When checked, the displayed temperature will read “NO
HEAT”.
3. “COOLDOWN” allows the user to change the designated time at the end of a cycle
where the heat relay is turned off. On “High” and “Medium” temperature settings, the
designated time cannot be reduced to less than 2 minutes.
4. “DEFAULT TEMP” allows the user to choose which general temperature setting, “High”,
“Medium” or “Low”, the control will default to at the beginning of each cycle if the
customer does not make a choice.
5. “ANTI WRINKLE” is a feature that periodically rotates the dryers after a cycle is
complete. If the door was closed at the end of the cycle, and is left closed for 5
minutes, the enunciator will sound and the display begins scrolling “ANTI WRINKLE”. 5
seconds later, the dryer motor will turn on for 60 seconds and then turn off. The heat
relay will not be turned on. The “ANTI WRINKLE” message will continue throughout the
time that the motor is turned on. The user can choose to enable or disable this feature.
To reset all values in the Cycles option to factory default, press “Enter” when the “DEFAULT”
prompt is shown. Press “Enter” again when the “RESET” prompt is shown to confirm the
action.

8514-254-001 rev. D page 18
The figure below shows the sub menu options for Cycles:

8514-254-001 rev. D page 19
Temperature Pricing Option:
This option allows the user to require additional vend amounts be added based on the
drying temperature chosen by the customer. This pricing adder is effective only for the Base
Vend Price (it does not affect the Extend Dry Price). It allows a pricing adder separate for
“Medium” and “Hot” temperature settings.
Example- A store owner has programmed the control for the following:
Vend Price $1.00
Vend Time 30 minutes
Extend Dry Price $.25
Extend Dry Time 8 minutes
Medium Adder $.25
Hot Adder $.50
In this case, the Vend Price is displayed as:
$1.00 if Low Temperature is chosen
$1.25 if Medium Temperature is chosen
$1.50 if Hot Temperature is chosen
When Temperature Pricing Adders are in place (user has chosen a higher value then $0.00), if
the customer attempts to change their temperature selection from a lower temperature to a
higher one during a drying cycle, there will be no change in the temperature selection. The
higher temperature buttons are disabled until the drying cycle is complete and a new Vend
Price is required.
The figure below shows the sub menu options for Temperature Pricing:

8514-254-001 rev. D page 20
Settings Options:
The Settings options allow for the user to make various programming changes to change how
the control operation affects the customer. See below for detailed information on each next
level option.
1. “Decimal Point”: If the user programs the Decimal Point to “OFF”, control display will
not show a decimal point on any vend price values. The factory default is “ON”.
2. “Display Time”: If the user programs this value to “MIN”, then minutes only will be
shown for the cycle time. If it is programmed to “MIN+SEC”, then minutes and seconds
will be shown. This also allows other programming changes, involving time, to be made
in either minute increments or minutes & seconds increments, as desired.
3. “Temp Scale”: If the user programs this value to “F”, then the temperatures will be
displayed in Fahrenheit units. If it is programmed to “C”, then the temperature will be
in Celsius units.
4. “Sounds”: If the user programs the Sounds to “OFF”, the control will not sound the
enunciator at the end of a dry cycle. The factory default is “ON”.
5. “Password”: If the user programs the password to any value other then 0000, the
control will prompt the user to enter a password (the programmed value) before
manual programming can be accessed. The factory default is “0000” (no password).
a. Note that if the user forgets the Password, it can be reset to factory default (no
password), by performing a hard reset on the control. Please refer to the
appropriate section of this manual to understand how to perform a hard reset.
b. The individual digits of the Password can be set by using the “Up” or “Down”
buttons to change the number that is flashing. Once the desired number is
chosen for a single digit, press the “Enter” button to move to the next one. Once
all four desired digits are chosen, the “Enter” button must be held down for 3
seconds to confirm that the complete password should be set.
6. “Central Pay”: If the user programs this value to “ON”, the left and right coin inputs
become upper and lower dryer coin inputs.
Central Pay “OFF” Central Pay “ON”
Left Coin Input Upper Dryer Input
Right Coin Input Lower Dryer Input
A system can then be installed that will register coin inputs per individual dryer
remotely from a Central Pay kiosk. The left and right coin prices must be appropriately
programmed. When this option is enabled, the controller will only display customer
prompts for a designated dryer. This designated dryer is determined when coins are
inserted at the Central Pay kiosk.
7. “Language”: The control uses English for the default language of the customer
prompts. Alternatively, the user can choose Spanish, French, Malay, or Italian for the
customer display prompts. However, all other prompts, such as Manual Programming,
USB Programming and any Error Codes will still display in English.
8. “Shift Hours”: This feature allows the user to shift the time used by the control from the
time kept internally by the control. The control uses a Real Time Clock (RTC) to
internally track the time and date. The RTC continues operation even if the control
loses external power. The RTC is set for Central Standard Time and no daylight savings.
Because the machine may be located in another time zone, the user can choose to