Dexter Laundry T-450SWD User manual

8514-298-001 REV A page 1
COMMERCIAL STACK WASHERS
MODELS T-350SWD, T-450SWD AND T-750SWD
VENDED C-SERIES CONTROL
OPERATOR’S MANUAL
INSTALLATION & OPERATION
INSTRUCTIONS
Please read this information and retain for reference.
WARNING - HIS WASHER IS EQUIPPED WI H DEVICES AND FEA URES RELA ING O I S SAFE
OPERA ION. O AVOID INJURY OR ELEC RICAL SHOCK, DO NO PERFORM ANY SERVICING UNLESS
QUALIFIED O DO SO.
I IS HE RESPONSIBILI Y OF HE OWNER O CHECK HIS EQUIPMEN ON A FREQUEN
BASIS O ASSURE I S SAFE OPERA ION.
A machine should NO be allowed to operate if any of the following occur:
- Excessively high water level.
- If machine is not connected to a properly grounded circuit.
- If the door does not remain securely locked during the entire cycle.
- Vibration or shaking from an inadequate mounting or foundation.
WARNING - SAFETY PRECAUTIONS
- Always shut off power and water supply before servicing.
- Do not overload the washer.
- Do not open door when cylinder is in motion or it contains water.
- Do not bypass any safety devices of this washer.
- Do not use volatile or flammable substances in or near this washer.
- Keep all panels in place. hey protect against shock and injury and add rigidity to the washer.
PREVENTIVE MAINTENANCE RE UIREMENTS
DAILY
- Check that the loading door remains securely locked and cannot be opened during an entire
cycle.
- Check the water connections for leaks.
- Clean the top, front, and sides of the cabinet to remove residue.
- Clean the soap dispenser and lid and check that all dispenser mounting screws are in-place and
tight.
- Check the drain valve for leaking and that it opens properly.
- Check the loading door for leaks. Clean the door seal of all foreign matter.
- Leave the loading door open to aerate the washer when not in use.
QUAR ERLY
- Make sure the washer is inoperative by switching off the main power supply.
- Check the V-belts for wear and proper tension.
- Clean lint and other foreign matter from around motor.
- Check all water connections for leaks.
- Wipe and clean the inside of the washer and check that all electrical components are free of
moisture and dust.
- Remove and clean water inlet hose filters. Replace if necessary.
- Check anchor bolts. Retighten if necessary
IMPORTANT: Replace any and all panels that were removed to perform daily and/or quarterly
maintenance.

8514-298-001 REV A page 2
TABLE OF CONTENTS
1 SPECIFICA ION SHEE ...................................................................................... 3
2 INS ALLA ION INS RUC IONS .......................................................................... 4
2.1 FOUNDA ION REQUIREMEN S ...................................................................... 4
2.2 MOUN ING .................................................................................................. 4
2.2.1 -350 SWD Machine Mounting Detail ....................................................... 6
2.2.2 -350 SWD Commercial Washer Dimensions ............................................ 7
2.2.3 -450 SWD Machine Mounting Detail ....................................................... 8
2.2.4 -450 SWD Commercial Washer Dimensions ............................................ 9
2.2.5 -750 SWD Machine Mounting Detail ..................................................... 10
2.2.6 -750 SWD Commercial Washer Dimensions .......................................... 11
2.3 PLUMBING ................................................................................................. 12
2.4 DRAIN ....................................................................................................... 12
2.5 PRO EC IVE FILM ...................................................................................... 12
2.6 ELEC RICAL ............................................................................................... 12
2.6.1 INS ALLING HE ELEC RICAL CONNEC ION ......................................... 14
2.6.2 FUSING REQUIREMEN S....................................................................... 14
2.6.3 CON ROLS RANSFORMER ................................................................... 15
2.7 OPERA ION CHECK .................................................................................... 15
3 OPERA ING INS RUC IONS ............................................................................. 16
3.1 S AR ING HE WASHER ............................................................................. 16
3.2 END OF CYCLE ........................................................................................... 17
3.3 EMERGENCY S OP / SAFE Y DOOR LOCK .................................................... 17
3.4 VARIABLE FREQUENCY DRIVE INDICA ORS ................................................ 17
4 MACHINE PROGRAMMING INS RUC IONS ........................................................ 19
4.1 MANUAL PROGRAMMING: ........................................................................... 19
4.2 Optional Cycles Option: ............................................................................... 22
4.3 Error Code Historical Log: ............................................................................ 23
4.4 Prices Option: ............................................................................................. 23
4.5 emp Pricing Option: .................................................................................. 24
4.6 Cycles Option: ............................................................................................ 24
4.7 Plus Cycle Options: ..................................................................................... 27
4.8 Settings: .................................................................................................... 30
4.9 Usage Menu: .............................................................................................. 33
4.10 Control Menu: ............................................................................................ 35
4.11 COIN WASHER DEFAUL CYCLE .................................................................. 36
4.12 WASHERS WI HOU COIN ACCEP ORS ....................................................... 36
4.13 RAPID ADVANCE MODE .............................................................................. 36
4.14 WA ER LEVEL ADJUS MEN ....................................................................... 37
5 DISPLAYED WASHER MESSAGES ....................................................................... 38
6 ROUBLESHOO ING ........................................................................................ 46
7 RANSIEN VOL AGE SURGE SUPPRESSORS .................................................... 50
8 SERVICE AND PAR S ........................................................................................ 51

8514-298-001 REV A page 3
1 SPECIFICATION SHEET
Capacity Dry Weight Capacity Per Machine - lb (kg) 20 (9.1) 30 (13.6) 50 (22. )
Washer Cylinder Volume - cu ft (L) 2. ( 6.5) 4 (113.3) 6.5 (184.1)
Dryer Cylinder Volume - cu ft (L) (198.2) 11.3 (320) 15.8 (44 .4)
Speed Washer High Extract Speed - g (RPM) 200 5 9 200 ( 50) 200 (685)
Washer Intermediate Extract Speed - g (RPM) 60 449 60 (411) 60 (3 5)
Washer Washing Speed - g (RPM) 0.9 55 0.9 (50) 0.9 (43)
Dryer Tumbler Speed - RPM 51 --- 4 --- 45 ---
Washer Motor Size - hp (kW) 1 (0. 5) 2 (1.5) 3 (2.2)
Dryer Motor Size - hp (kW) 1/3 (0.25) 1/2 (0.38) 2 & 1/2 (1.5 & 0.38)
Airflow 60 Hz Model (Dryer Only) - cfm (M3/min) 3 0 (10.5) 500 (14.6) 650 (18.4)
50 Hz Model (Dryer Only) - cfm (M3/min) 300 (8.5) 450 (12. ) 510 (14.4)
Dimensions Overall Cabinet Height - in (cm) 4 3/4 (189.9) 8 3/8 (199) 8 3/16 (221.5)
Overall Cabinet Width - in (cm) 2 (68.6) 31 1/2 (80) 34 1/2 (8 .6)
Overall Cabinet Depth - in (cm) 44 5/8 (113. ) 49 /16 (125.6) 54 5/8 (138. )
Washer Cylinder Diameter - in (cm) 21 (53.3) 25 (63.5) 30 ( 6.2)
Washer Cylinder Depth - in (cm) 13 1/2 (34.3) 14 1/8 (35.9) 16 (40.6)
Washer Door Opening - in (cm) 12 1/4 (31.1) 15 1/4 (38. ) 19 1/4 (48.9)
Floor to Washer Door Bottom - in (cm) 14 /8 (3 .8) 12 /16 (31.6) 16 (40.6)
Dryer Cylinder Diameter - in (cm) 25 1/2 (64.8) 30 ( 6.2) 32 1/2 (82.5)
Dryer Cylinder Depth - in (cm) 24 (61) 2 1/2 (69.9) 33 (83.8)
Dryer Door Opening - in (cm) 18 1/8 (46) 22 11/16 (5 .6) 25 5/8 (65.1)
Floor to Dryer Door Bottom - in (cm) 48 1/4 (122.6) 4 3/8 (120.3) 55 1/8 (140)
Dryer Lint Screen Area - sq in (sq cm) 285 (1839) 453 (2923) 544 (3510)
Weight Net Weight - lb (kg) 800 (362.9) 1051 (4 6. ) 1600 ( 25. )
Shipping Shipping Weight - lb (kg) 840 (381) 1101 (499.4) 1650 ( 48.4)
Shipping Height - in (cm) 80 5/8 (204.8) 84 (213.4) 91 5/8 (232. )
Shipping Width - in (cm) 29 1/4 ( 4.3) 34 (86.4) 35 /8 (91.1)
Shipping Depth - in (cm) 49 3/4 (126.4) 54 (13 .2) 63 1/2 (161.3)
Installation Min. Clearance Between Machines - in (cm) 1/2 (1.3) 1/2 (1.3) 1/2 (1.3)
Min. Clearance Behind Machines - in (cm) 24 (61) 24 (61) 24 (61)
Min. Concrete Thickness - in (cm) 6 (15.2) 6 (15.2) 8 (20.3)
Make-Up Air Required - sq ft (sq cm) 0. (650) 1 (929) 1 (929)
Exhaust Size - in (cm) 6 (15.2) 6 (15.2) 8 (20.3)
Max. Exhaust Back Pressure (Water Column) - in (mm) 0.3 ( .6) 0.3 ( .6) 0.3 ( .6)
Recommended Exhaust Length - ft (m) & 2 elbows 14 (4.3) 14 (4.3) 14 (4.3)
Water Water Inlet Size - in (mm) 3/4 (19) 3/4 (19) 3/4 (19)
Pressure (min-max) - psi (kPa)
30-120 (20 -82 ) 30-120 (20 -82 ) 30-120 (20 -82 )
Flow Rate - gal/min (L/min) 9 (34) 9 (34) 9 (34)
Approx. Water Usage Per Cycle - gal (L) 15.8 (59.8) 23.5 (89) 38.4 (145.4)
Drain Diameter (O.D.) - in (cm) 2 1/4 (5. ) 3 ( .6) 3 ( .6)
Floor to Center of Drain - in (cm) 5 /8 (14.9) 4 /16 (11.3) 6 5/8 (16.8)
Gas (Gas Models Only)
Gas Supply Connection - in (mm) 1/2 (12. ) 1/2 (12. ) 1/2 (12. )
Natural Gas Supply (Water Column) - in (cm) 5-10 (12. - 25.4) 5-10 (12. - 25.4) 5-10 (12. - 25.4)
LP Gas Supply (Water Column) - in (cm) 11 1/2 - 14 (29.2 - 35.6) 11 1/2 - 14 (29.2 - 35.6) 11 1/2 - 14 (29.2 - 35.5)
Gas Usage - 60Hz Model - BTU/hr (kW) 56,000 (16.4) 80,000 (23.4) 108,000 (31. )
Gas Usage - 50Hz Model - BTU/hr (kW) 4 ,000 (13.8) 4,000 (21. ) 96,000 (28.3)
Electrical Model Volts / Hz / Phase / Wiring
208-240 / 60 / 1 / 2 wire + ground
208-240 / 60 / 3 / 3 wire + ground
Gas Dryer 208-240 / 60 / 1 / 2 wire + ground
208-240 / 60 / 1 / 2 wire + ground
208-240 / 60 / 3 / 3 wire + ground
120 / 60 / 1 / 2 wire + ground
208-240 / 60 / 1 / 2 wire + ground
Washer 230 / 50 / 1 / 2 wire + ground
Gas Dryer 230 / 50 / 1 / 2 wire + ground
Washer 230 / 50 / 1 / 2 wire + ground
Gas Dryer 230 / 50 / 1 / 2 wire + ground
Model kW / Volts / Hz / Phase / Wiring
Washer 230 / 50 / 1 / 2 wire + ground
Electric Dryer 24 / 400 / 50 / 3 / 4 wire + ground
Washer 230 / 50 / 1 / 2 wire + ground
Electric Dryer 15 / 400 / 50 / 3 / 4 wire + ground
-16 Washer --- --- 20 / 8.4 / #12
---
---
15 / 10 / #12
T-350 STACK WASHER-DRYER UNIT
T-750 STACK WASHER-DRYER UNIT
T-450 STACK WASHER-DRYER UNIT
---
Circuit Breaker Amps / Running Amps / Wire Size
---
15 / 6.2 / 3.5 mm²
15 / 6.2 / #12 15 / 6.5 / #12 ---
15 / 3.9 / #12
15 / 4 / #12
---
Circuit Breaker Amps / Running Amps / Wire Size
-1
Washer
Gas Dryer
15 / 1.9 / #12
15 / 2.5 / #12
-39
15 / 6.5 / 3.5 mm²
---
15 / 5 / 3.5 mm²
---
-59 --- ---
15 / 6.5 / 3.5 mm²
20 / 8.4 / 3.5 mm²
15 / 3.4 / 3.5 mm²
15 / 5 / 3.5 mm²
15 / 10 / 3.5 mm²
---
15 / 6.5 / 3.5 mm²
---
-82
---
---
15 / 6.2 / 3.5 mm²
30 / 30 / 8.4 mm²
---
- 9
50 / 45 / 13.3 mm²
---
---

8514-298-001 REV A page 4
2 INSTALLATION INSTRUCTIONS
his washer may have been purchased as part of a stacked washer/dryer. In
addition to these instructions, please also refer to the installation instructions
that accompany the dryer when installing this product.
All washers must be installed in accordance with all local, state and national
building, electrical, plumbing and other codes in effect in the area.
WARNING:
THESE INSTALLATION AND SERVICING INSTRUCTIONS ARE FOR USE
BY UALIFIED PERSONNEL ONLY. TO AVOID INJURY AND ELECTRICAL
SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THAT
CONTAINED IN THE OPERATING INSTRUCTIONS, UNLESS UALIFIED.
2.1 FOUNDA ION REQUIREMEN S
his machine is designed for use on or over bare concrete floor - not to be
used above combustible flooring, such as carpet or wood. he washer
must be securely bolted and grouted to a substantial concrete floor, or
mounted and grouted upon a suitable base that is securely bolted and
grouted to a substantial concrete floor.
CARE MUS BE AKEN WI H ALL FOUNDA ION WORK O ENSURE A
S ABLE UNI INS ALLA ION, ELIMINA ING POSSIBILI IES OF
EXCESSIVE VIBRA ION.
All installations require concrete floors and quality grade anchor bolts or
expansion anchors. Mounting hardware is not provided with the
machines. Refer to appropriate model Machine Mounting Detail Figures 1-
1, 1-2 and 1-3 for floor thickness and bolt sizes. See mounting diagram
for overall washer dimensions.
2.2 MOUN ING
A concrete pedestal or steel-mounting base that elevates the machine
above the floor level is recommended to provide easy access to the
loading door.
Recommended height:
-350 SWD: approximately 8 inches (200 mm)
-450 SWD: approximately 6 inches (152 mm)
-750 SWD: approximately 4 inches (102 mm)
Allow a minimum 24 inches (610 mm) of clearance behind the rear of the
machine to provide access for motor service. Contact a Dexter laundry
equipment distributor for recommended steel mounting bases.
If an elevated concrete pedestal is desired, it should be embedded and
tied into the existing floor (cut through existing floor as shown). See

8514-298-001 REV A page 5
Machine Mounting Detail Figures for floor thickness and bolt sizes.
EXPANSION ANCHORS ARE NO RECOMMENDED FOR USE IN CONCRE E
PEDES ALS BECAUSE HE ANCHORS ARE OO CLOSE O AN EDGE,
CAUSING I O BREAK OU .

8514-298-001 REV A page 6
2.2.1 -350 SWD Machine Mounting Detail

8514-298-001 REV A page 7
2.2.2 -350 SWD Commercial Washer Dimensions

8514-298-001 REV A page 8
2.2.3 -450 SWD Machine Mounting Detail

8514-298-001 REV A page 9
2.2.4 -450 SWD Commercial Washer Dimensions

8514-298-001 REV A page 10
CONCRETE PEDESTAL MOUNTING
Figure 1-1 Figure 1-2
FLOOR OUTLINE
Figure 1-3
MACHINE MOUNTING DETAIL
2.2.5 -750 SWD Machine Mounting Detail

8514-298-001 REV A page 11
2.2.6 -750 SWD Commercial Washer Dimensions

8514-298-001 REV A page 12
2.3 PLUMBING
Water supply hoses are provided with each machine. he threaded
connections on the hoses are ¾-11 ½ NH for 60 Hz models and ¾-14
BSP for 50 Hz models.
Separate hot and cold water lines must be supplied to the machine,
maintaining 30 psi to 120 psi (207 kPa to 827 kPa) water flow pressure. A
140°F (60°C) hot water supply is recommended for best washing results.
Do not exceed 180°F (82°C) water temperature.
2.4 DRAIN
he drain outlet tube size:
For - 350 SWD is 2 ¼ inches (57 mm) in diameter,
and for -450 SWD and -750 SWD is 3 inches (76 mm) in diameter.
Any drain hose used must be lower than the drain valve to assure proper
draining.
2.5 PRO EC IVE FILM
he machine may have protective adhesive film on the front control panel
label area and on the front, top, and side stainless steel panels. he film
may be peeled off before putting the machine into service.
2.6 ELEC RICAL
he Dexter single/three-phase 208-240VAC 60 Hz (single phase 230VAC
50 Hz) washing machines are intended to be permanently installed
appliances. No power cord is provided. he machine should be
connected to an individual branch circuit not shared by lighting or other
equipment. A means for disconnection with a contact separation of at
least 1/8” (3 mm) must be provided. he connection should be sheathed
in liquid-tight or approved flexible conduit, or equivalent, with conductors
of the proper size and insulation (50 Hz: he sheath of the supply cord
must be at least equivalent to that of a cord complying with IEC 227 or
IEC 245). A qualified technician should make such connections in
accordance with the wiring diagram. See specification sheet for minimum
recommended wire size.
Individual circuit breakers for each unit are required. Do not use ground-
fault (earth-fault) circuit breakers or ground-fault (earth-fault) circuit
interrupter outlets.

8514-298-001 REV A page 13
WARNING:
SHUT OFF POWER AND WATER BEFORE OPENING ANY SERVICE
PANELS.
ELECTRICAL CONNECTIONS

8514-298-001 REV A page 14
2.6.1 INS ALLING HE ELEC RICAL CONNEC ION
2.6.1.1 Disconnect all power to the washer.
2.6.1.2 Remove the top panel of the washer and locate the power terminal block
near the back of the control compartment.
2.6.1.3 If power is 208-240V-3PH-60Hz, connect L1, L2, L3 and Ground. If there
is a high leg, it must NO be connected to L1 or L2. However, failure due
to a voltage surge on the high leg is not covered by equipment warranty.
Contact Dexter Laundry with any questions.
2.6.1.4 If power is 208-240V-1PH-60Hz, connect L1, L2 and Ground.
2.6.1.5 If power is 230V-1PH-50Hz, connect L1, N and Earth.
NO E: It is important that the grounding screw next to the power
terminal block be connected to a good external ground.
2.6.2 FUSING REQUIREMEN S
Single- and hree -phase models:
See specification sheet for required IME-DELAY (DUAL ELEMEN )
FUSE size (or equivalent circuit breaker)

8514-298-001 REV A page 15
2.6.3 CON ROLS RANSFORMER
he controls transformer is located inside the control trough and
steps a range of 180 to 255 volts down to 24 volts. here are two
terminals on the controls transformer for the primary (incoming)
power. Use the terminal marked “L1 200V” for power supplies
between 180 and 229 volts. Use the terminal marked “L1 230V” for
power supplies between 230 and 255 volts.
2.7 OPERA ION CHECK
After all mounting, plumbing and electrical work is completed, run the
machine through a complete wash cycle. Check for water leaks and verify
proper operation.
During intermediate spin and final spin, the cylinder should turn in a
counterclockwise direction when viewed from the front of the machine.
If spin is clockwise, the 1 and 2 motor wires connecting to terminal 1
and 2 on the variable frequency drive should be swapped. Remove
power to the machine before opening service panels and swapping wires.

8514-298-001 REV A page 16
3 OPERATING INSTRUCTIONS
3.1 S AR ING HE WASHER
3.1.1 urn on power to the washer.
3.1.2
Load the laundry.
Place laundry into the cylinder and latch the door securely. Be sure
laundry does not get caught between the door gasket and tub front
when closing the door. Maximum load is the dry weight capacity
listed in the specification sheet. Do not exceed the listed capacity
weight.
NOTE: o begin closing the door, the handle must be in the
horizontal position. After moving the door to the closed position,
the handle must be turned down to the vertical position in order to
latch the door for machine operation.
3.1.3 Select cycle temperature.
Select the appropriate cycle for the type of load being washed. Use
the “UP” and “DOWN” keys to change the cycle on the display to
the desired cycle and press the enter button to select.
3.1.4 Add washing chemicals.
Add low sudsing powdered detergent into the “DE ERGEN ”
compartment of the automatic dispenser on the top or front of the
washer.
If liquid wash products are used in the “DE ERGEN ”
compartment, they must be added at the beginning of the wash
cycle.
If desired, add fabric softener to the “FABRIC SOF ENER”
compartment. Use the amount of fabric softener as recommended
by the manufacturer.
If the machine is set for pre-wash, washing products can be added
to the round opening of the dispenser or put in with the clothes
when loading the washing machine.
If bleach is desired, DO NO place into dispenser until the ADD
BLEACH message is displayed.
3.1.5 Start wash cycle.
Insert coins, tokens or debit card to meet the displayed vend price.
he display will count down the amount needed to meet the vend
price. Once the vend price is met, the display will read “PRESS
S AR ” and the start button LED will blink. If the door is not closed
and latched, the display will read “CLOSE DOOR” and the control
will wait until the door is latched to continue. Pressing the start
button will begin the cycle and activate the ON light. he display
will show the remaining cycle time in minutes. he clothes door
will lock and remain locked until the end of the cycle.

8514-298-001 REV A page 17
3.2 END OF CYCLE
When the cycle is complete a 3-second tone will sound and the display will
read “CYCLE DONE HANK YOU” until the door is opened. he door can
now be opened. Leave the clothes door open when the machine is not in
use.
3.3 EMERGENCY S OP / SAFE Y DOOR LOCK
his machine is equipped with a Safety Door Lock that locks the door
closed from when the cycle is started until the cycle is complete. he door
lock prevents opening the door for up to 3 minutes if the power is
interrupted during the cycle.
he Emergency Stop button pauses the washer and allows the door to be
opened during the cycle after the Safety Door Lock releases. When the
Emergency Stop button is pressed an alarm will sound and the display will
begin counting down and read “S OP 3”, “S OP 2”, “S OP 1”. If the
button is released before 3 seconds elapse, the alarm will stop and the
cycle will continue normally. If the Emergency Stop is held down for 3
seconds, the display will count down and the washer will begin stopping
movement and water flow and begin draining water from inside the
washer. hough the machine may stop wash movement quickly, it may
take up to 3 minutes for the door to unlock. During that time the alarm
will continue to sound and the display will read “S OPPING”. When the
alarm stops, the door may be opened. he washer may be restarted by
closing and latching the door, and pressing the Start button. If the
washer was stopped more than once before the final extract, the cycle will
be cancelled. If the washer was stopped during final extract, the cycle will
be ended. If the washer is stopped for more than 1 hour, the cycle will be
terminated.
3.4 VARIABLE FREQUENCY DRIVE INDICA ORS
here are three small red LEDs located on the upper Variable Frequency
Drive (VFD) cover. hey are labeled as “READY”, “RUN”, and “FAUL ”
and can be used for troubleshooting. he definitions of the LEDs are
listed in able 1 below.

8514-298-001 REV A page 18
Table 1: Variable Frequency Drive Indicators
Washer Condition
“READY”
LED
Status
“RUN”
LED Status
“FAUL ”
LED
Status
Idle Mode
(No Cylinder Movement) ON OFF OFF
umbling ON ON OFF
Stop from umble ON FLASHING OFF
Ramp to Intermediate or
Final Extract Spin ON ON OFF
Spinning
(Intermediate or Final) ON ON OFF
Stop from Spin
(Intermediate or Final) ON FLASHING OFF
Faulted ON OFF ON

8514-298-001 REV A page 19
4 MACHINE PROGRAMMING INSTRUCTIONS
he washer control can be programmed to prompt the user for alternate vend prices,
change washer cycle times, temperatures and many other options. his can be
accomplished in two ways:
1. Manual programming utilizing the “Start”, “Hot”, “Warm” and “Cold” buttons
2. USB download of a customizable User File. For instructions on using the USB
download feature, please contact your local Dexter distributor or visit
dexterlive.com.
4.1 MANUAL PROGRAMMING:
he washer must be in idle mode for the manual programming menus to be accessed.
Idle mode is when the washer is not actively running a wash cycle and the vend price is
displayed on the screen.
o enter the manual programming mode, the programming button needs to be pressed
for 1 second. he control should display “PROGRAMMING”. here are two
programming buttons on this washer. One is on the control board behind the front
panel and an auxiliary button is inside the coin vault.
he figure below shows the location of the programming button and USB port inside of
the coin vault.

8514-298-001 REV A page 20
When manual programming mode is entered, the “Start”, “Hot”, “Warm” and “Cold”
buttons perform alternate functions.
Button Name Alternate Function in Programming Mode
Start Becomes the action to accept the displayed option or
the “Enter” key
Hot Becomes the action to move UP through displayed
options (Press & hold for accelerated scrolling)
Warm Becomes the action to move DOWN through displayed
options (Press & hold for accelerated scrolling)
Cold Becomes the action to move back a step (1 press) or
EXI from programming mode (press for 3 seconds)
hese alternate functions allow the user to move through a menu of options to choose
various programmable settings. he figure below shows the top level menu. Choosing
an option from the top level menu will then display the next level of options (the sub
menu).